Effect of Ball Scribing on Magnetic Shielding Efficiency of Grain-oriented Silicon Steel

Magnetic shielding of grain-oriented silicon steel was investigated. Ball scribing with spacing of 2 to 16 mm was performed at peak flux densities of 8.0 mT to 1.3 T. Magnetic shielding efficiency was calculated, including absorption, reflection and inner multi-reflection shielding efficiencies. Magnetic shielding efficiency （MSE） increase ratios after different scribing spacing were compared, and thickness requirement to achieve absorption shielding of 50 dB was also calculated. The results show that magnetic shielding efficiencies of C711 and H668 silicon steels increase by 4.79 and 3.15 dB respectively after scribing of 16 mm. Before scribing, shielding efficiency of H668 steel was higher than that of C711 steel, while after scribing, both absorption and shielding efficiency gaps were largely abridged between C711 and H668 steels. Plate thickness of C711 steel could be reduced from 3.18 mm without scribing to 2. 20 mm after scribing of 16 mm. There is no apparent thickness reduction at lower flux densities; while the peak flux density is above 0.3 T, the shielding effect becomes apparent, and the thickness could be reduced from 2.28 mm without scribing to 1.70 mm with scribing spacing of 16 ram. Magnetizing process and its effect on variation of magnetic shielding were also analyzed.

NSRT台站L频段RFI测量及干扰缓解（英文）

Radio environment degrades significantly at Nan Shan 26 m Radio Telescope(NSRT) base due to new and upgraded electrical devices on-site and more establishment of surrounding radio communication services. How do we mitigate them effectively? Firstly, a quasi-real time Radio Frequency Interference(RFI) measurement method is employed for RFI detection and spectral analysis based on the layout for potential on-site interference areas and off-site radio communication services. Our investigation at the frequency bands for pulsar observations(1380–1700 MHz) indicates that transient interferences pose the greatest impact on observations. Then we use a portable RFI measurement system for interferences hunting at the NSRT, and the typical characteristics of interferences are analyzed. Secondly, based on the RFI characteristics, main interference sources in the observation room are shielded with shielding cabinets. The results from our shielding efficiency(SE) measurement and evaluation show that these methods work effectively.Furthermore, we propose a Radio Quiet Zone(RQZ) and the regulations for NSRT to mitigate off-site RFIs.

Particular properties of Ti_2O and TiN_x nanoparticles prepared by thermal decomposition

Particular properties of Ti2O and TiNx prepared by thermal decomposition were introduced. A precursor prepared by titanium powder reacting with oxalate acid was thermally decomposed in nitrogen atmosphere at 840℃ for 15 min, and relatively pure Ti2O was then obtained. Conductive TiNx was also prepared after altering reaction conditions. Samples were characterized by resistivity, X-ray powder diffraction, transmission electron microscope, Ultraviolet-Visible diffuse reflection, and electromagnetic shielding efficiency. The results indicate that both Ti2O and TiNx have good conductivity. Moreover, Ti2O shows a better solar photocatalytic activity and TiNx does well in the electromagnetic shield.

Additive Manufacturing of Large-scale Metal Mesh with Core-shell Composite Structure for Transparent Electromagnetic Shielding/glass Heater

Transparent electromagnetic(EM)shielding glass with a metal mesh has significant potential for application in different fields of EM radiation and anti-EM interference light-transmitting observation windows.In particular,a transparent EM-shielding glass with a large-aspect-ratio metal mesh can effectively alleviate the contradictory problems of shielding effectiveness and light-transmission performance constraints.However,the fabrication of high-aspect-ratio metal meshes on glass substrates has problems such as high cost,complex processes,low efficiency,small area,and easy damage issues,which limit their application in the field of high-performance,transparent EM-shielding glass.Therefore,this paper proposes a composite additive manufacturing process based on electric-field-driven microjet 3D printing and electroplating.By fabricating metal meshes with an Ag-Cu core-shell structure on a glass substrate,EM-shielding glass with high shielding efficiency and light transmission can be manufactured without increasing the aspect ratio of the metal meshes.The prepared Ag-Cu composite metal mesh has excellent optoelectronic properties(period 250𝜇m,line width 10𝜇m,90.1%transmission at 550 nm visible light,square resistance 0.21Ω/sq),efficient electrothermal effect(3 V DC voltage can reach 189°C steady-state temperature),stable EM-shielding effectiveness(average shielding effectiveness 23 dB at X-band),and acceptable mechanical and environmental stability(less than 3%change in square resistance after 150-times adhesion test and less than 6%and 0.6%change in resistance after 72 h in acid and alkali environments,respectively).This method provides a new solution for the mass production of high-performance large-area transparent electric heating/EM-shielding glass.