The effects of lamellar structure on deformation and fracture behavior in a Ti 48Al 2Mn 2Nb alloy produced by centrifugal spray deposition(CSD) were investigated. The deformation and fracture of samples after tensile ...The effects of lamellar structure on deformation and fracture behavior in a Ti 48Al 2Mn 2Nb alloy produced by centrifugal spray deposition(CSD) were investigated. The deformation and fracture of samples after tensile and compressive tests were examined in a scanning electron microscope (SEM). The in situ tensile testing was further carried out in a SEM and the crack growth path of samples was observed. The result shows that there is a remarkable effect of lamellar structure of CSD TiAl alloy on its deformation and fracture process. Especially, the main crack extension is dependent on the lamellar direction relative to tensile loading axis. SEM observations indicate that there is a shielding toughening effect of lamellar structure on fracture in CSD samples, such as, crack deflection, crack path tortuousity, and crack branching, etc. Moreover, the crack growth path shows that the main crack grows tortuously and uncontinuously by ligaments bridging many microcracks in front of crack tip. The effect mechanism of microstructure on deformation and fracture process is discussed.[展开更多
The effect of Al in Ti-microalloyed welding wire on microstructure and toughness of deposited metals is studied.The results show that the deposited metal toughness worsens with increasing Al in wire' The mechanis...The effect of Al in Ti-microalloyed welding wire on microstructure and toughness of deposited metals is studied.The results show that the deposited metal toughness worsens with increasing Al in wire' The mechanism of Al is as follows:(1) Al makes oxygen content in deposited metal increase.(2)Al restrains the formation of Ti-rich oxide inclusion, which causes granular bainite microstructure in deposited metal.(3)The content of solute Ti in deposited metal increases with Al content in welding wire,as a result,a part of carbonrich constitution in deposited metal is in the form of twin martensite.展开更多
The Co Mg O and Co Mn Mg O catalysts are prepared by a co-precipitation method and used as the catalysts for the synthesis of carbon nanotubes（CNTs） through the catalytic chemical vapor deposition（CCVD）. The effec...The Co Mg O and Co Mn Mg O catalysts are prepared by a co-precipitation method and used as the catalysts for the synthesis of carbon nanotubes（CNTs） through the catalytic chemical vapor deposition（CCVD）. The effects of Mn addition on the carbon yield and structure are investigated. The catalysts are characterized by temperature programmed reduction（TPR） and X-ray diffraction（XRD） techniques, and the synthesized carbon materials are characterized by transmission electron microscopy（TEM） and thermo gravimetric analysis（TG）. TEM measurement indicates that the catalyst Co Mg O enclosed completely in the produced graphite layer results in the deactivation of the catalyst. TG results suggest that the Co Mn Mg O catalyst has a higher selectivity for CNTs than Co Mg O. Meanwhile, different diameters of CNTs are synthesized by Co Mn Mg O catalysts with various amounts of Co content, and the results show that the addition of Mn avoids forming the enclosed catalyst, prevents the formation of amorphous carbon, subsequently promotes the growth of CNTs, and the catalyst with decreased Co content is favorable for the synthesis of CNTs with a narrow diameter distribution.The Co Mn Mg O catalyst with 40% Co content has superior catalytic activity for the growth of carbon nanotubes.展开更多
An optical transmission method was used in-situ to measure the rate of pyrolytic deposition from Mn_2(CO)_(10) induced by a CW CO_2 laser. The effect of the laser intensity, Mn_2(CO)_(10) vapor pressure and added gase...An optical transmission method was used in-situ to measure the rate of pyrolytic deposition from Mn_2(CO)_(10) induced by a CW CO_2 laser. The effect of the laser intensity, Mn_2(CO)_(10) vapor pressure and added gases (CO, O_2 and Ar) on the deposition rate has been examined.展开更多
Textured Bi and MnBi/Bi thin films are prepared by the pulsed laser deposition method. The highly c-axis textured MnBi films are obtained by annealing the bilayer consisting of textured Bi and Mn films. The eoerciviti...Textured Bi and MnBi/Bi thin films are prepared by the pulsed laser deposition method. The highly c-axis textured MnBi films are obtained by annealing the bilayer consisting of textured Bi and Mn films. The eoercivities of the MnBi/Bi film are 1.5 T and 2.35 T at room temperature and at 373K, respectively, showing a positive temperature coefficient. Microstructural investigations show that the textured MnBi film results from the orientated growth induced by the textured Bi under-layer.展开更多
基金Project (E990 0 0 7)supportedbyFujianProvincialNaturalScienceFoundation P .R .China
文摘The effects of lamellar structure on deformation and fracture behavior in a Ti 48Al 2Mn 2Nb alloy produced by centrifugal spray deposition(CSD) were investigated. The deformation and fracture of samples after tensile and compressive tests were examined in a scanning electron microscope (SEM). The in situ tensile testing was further carried out in a SEM and the crack growth path of samples was observed. The result shows that there is a remarkable effect of lamellar structure of CSD TiAl alloy on its deformation and fracture process. Especially, the main crack extension is dependent on the lamellar direction relative to tensile loading axis. SEM observations indicate that there is a shielding toughening effect of lamellar structure on fracture in CSD samples, such as, crack deflection, crack path tortuousity, and crack branching, etc. Moreover, the crack growth path shows that the main crack grows tortuously and uncontinuously by ligaments bridging many microcracks in front of crack tip. The effect mechanism of microstructure on deformation and fracture process is discussed.[
文摘The effect of Al in Ti-microalloyed welding wire on microstructure and toughness of deposited metals is studied.The results show that the deposited metal toughness worsens with increasing Al in wire' The mechanism of Al is as follows:(1) Al makes oxygen content in deposited metal increase.(2)Al restrains the formation of Ti-rich oxide inclusion, which causes granular bainite microstructure in deposited metal.(3)The content of solute Ti in deposited metal increases with Al content in welding wire,as a result,a part of carbonrich constitution in deposited metal is in the form of twin martensite.
基金Project supported by the National Basic Research Program of China(Grant No.2011CB201202)
文摘The Co Mg O and Co Mn Mg O catalysts are prepared by a co-precipitation method and used as the catalysts for the synthesis of carbon nanotubes（CNTs） through the catalytic chemical vapor deposition（CCVD）. The effects of Mn addition on the carbon yield and structure are investigated. The catalysts are characterized by temperature programmed reduction（TPR） and X-ray diffraction（XRD） techniques, and the synthesized carbon materials are characterized by transmission electron microscopy（TEM） and thermo gravimetric analysis（TG）. TEM measurement indicates that the catalyst Co Mg O enclosed completely in the produced graphite layer results in the deactivation of the catalyst. TG results suggest that the Co Mn Mg O catalyst has a higher selectivity for CNTs than Co Mg O. Meanwhile, different diameters of CNTs are synthesized by Co Mn Mg O catalysts with various amounts of Co content, and the results show that the addition of Mn avoids forming the enclosed catalyst, prevents the formation of amorphous carbon, subsequently promotes the growth of CNTs, and the catalyst with decreased Co content is favorable for the synthesis of CNTs with a narrow diameter distribution.The Co Mn Mg O catalyst with 40% Co content has superior catalytic activity for the growth of carbon nanotubes.
文摘An optical transmission method was used in-situ to measure the rate of pyrolytic deposition from Mn_2(CO)_(10) induced by a CW CO_2 laser. The effect of the laser intensity, Mn_2(CO)_(10) vapor pressure and added gases (CO, O_2 and Ar) on the deposition rate has been examined.
基金Supported by the National Natural Science Foundation of China under Grant Nos 51171001,51371009 and 50971003the Foundation of Key Laboratory of Neutron Physics of CAEP under Grant No 2014BB02
文摘Textured Bi and MnBi/Bi thin films are prepared by the pulsed laser deposition method. The highly c-axis textured MnBi films are obtained by annealing the bilayer consisting of textured Bi and Mn films. The eoercivities of the MnBi/Bi film are 1.5 T and 2.35 T at room temperature and at 373K, respectively, showing a positive temperature coefficient. Microstructural investigations show that the textured MnBi film results from the orientated growth induced by the textured Bi under-layer.
