Magnetic levitation performance of high-temperature superconductor over three magnetic hills of permanent magnet guideway with iron shims of different thicknesses

Superconducting magnetic levitation performance, including levitation force and guidance force, is important for the application of high-temperature super- conducting maglev. Both of them are not only affected by different arrays of superconductors and magnets, but also by the thickness of the iron shim between permanent magnets. In order to obtain the best levitation performance, the magnetic field distribution, levitation force, and guidance force of a new type of three magnetic hills of permanent magnet guideway with iron shim of different thicknesses （4, 6, and 8 mm） are discussed in this paper. Simulation analysis and experiment results show that the guideway with iron shim of 8 mm thickness possesses the strongest magnetic field and levitation performance when the suspension gap is larger than 10 mm. However, with the decreasing of suspension gap, the guideway with iron shim of 4 mm thickness possesses the best levitation performance. The phenomena can be attributed to the density distribution of flux and magnetization of iron shim.

IPv6多宿主技术研究

多宿主技术具有提高网络可靠性、实现负载均衡等许多优点,因此在IPv6网络中将被广泛地应用。但是,多宿主的实施会给网络带来许多问题。本文总结了目前实现IPv6多宿主技术的几种方法。根据这些方法的特点,我们将其分类归纳为四种策略,并进行比较,还重点介绍了Shim6方法的原理。文中还指出了IPv6多宿主技术在实际应用中应该考虑的因素,并提出了一种基于地址隐匿和识别的方法。最后,本文对多宿主技术的发展趋势进行了预测,探讨了研究面临的一些具体问题以及未来的研究方向。

中科院近物所的SHIM物理研究

简要介绍了 SHIM物理及其近 1 0年来国际研究的最新进展 ,重点介绍了中国科学院近代物理研究所在该学科研究中所获得的部分最新研究结果 ,展望了

Vibration characteristics of rotor system with tilting-pad journal bearing of elastic and damped pivots

In view of an entire dynamic model of tilting-pad journal bearing(TPJB) in which the pads swing and vibrate along geometric direction of preload, a TPJB of elastic and damped pivots was designed and manufactured. Vibration experiments were carried out under the conditions of different rotor bending stiffness and oil supply pressure to find out the relationship between the new bearing's vibration depression effect and other dynamic parameters of the rotor. The result shows that critical amplitudes can be efficaciously reduced while system's stability can be remarkably improved by this bearing. Besides, the bearing's effect of vibration depression weakens as the rotor bending stiffness increases, but heightens it as the oil supply pressure increases.

一种基于动态SHIM的视频拖拽点播方案

在此阐述了B/S架构的可视化系统中拖拽点播功能的实现方案。针对拖拽点播中播放控件遮蔽页面元素和窗口无法定位的问题,给出了基于SHIM技术的解决方法。通过动态SHIM技术,对拖拽DOM节点进行处理,对zTree树形组件进行改进,解决了Active X播放控件遮蔽页面元素的问题。同时,设计了基于SHIM位置的动态偏移算法,解决了播放窗口无法定位的问题。该方案为Web项目中拖拽问题提供了有效的解决思路,提升了用户体验。

Comparison of FASTMAP and <i>B</i>₀Field Map Shimming at 4T: Magnetic Field Mapping Using a Gradient-Echo Pulse Sequence

Local susceptibility variations result in B0 field inhomogeneities, causing distortions and signal losses in MR imaging. Susceptibility variations become stronger with increasing B0 magnetic field strength. Active shimming is used to generate corrective magnetic fields, which can be used to improve B0 field homogeneity. FASTMAP is an effective shimming technique for computing optimal coil currents, which uses data from six projection directions (or columns): this technique is routinely used for shimming cubic volumes of interest (VOIs). In this paper, we propose several improvements to FASTMAP at 4T. For each shim coil, using a modified 3D gradient-echo pulse sequence, we compute B0 inhomogeneity maps and project them onto eight 1st and 2nd order spherical harmonic functions. This process is repeated for shim currents between -15,000 to 15,000 with increments of 5000 Digital to Analog Converter (DAC) units, and is used to compute the gradient between spherical harmonic coefficients and DAC values for all 8 shim coils—along with the R2 values of linear fits. A method is proposed (based on R2 values) to further refine optimal shim currents in respective coils. We present an analysis that is numerically robust and completely flexible in the selection of the VOIs for shimming. Performance analyses, phantom results, and in vivo results of a human brain are presented, comparing our methods with the FASTMAP method.

Method for secondary spring load equalization of railway vehicles with two-stage spring suspension: Modeling and optimal regulation

To ensure running safety,the secondary spring loads of railway vehicles must be well equalized.Due to the coupling interactive effects of these hyper static suspended structures,the equalization adjustment through shimming procedure is quite complex.Therefore,an effective and reliable method in application is developed in this paper.Firstly,the best regulation of spring load is solved based on a mechanical model of the secondary suspension system,providing a target for actual adjustment.To reveal the relationship between secondary spring load distribution and shim quantity sequence,a forecasting model is constructed and then modified experimentally with consideration of car body’s elastic deformation.Further,a gradient-based algorithm with a momentum operation is proposed for the load optimization.Effectiveness of the whole method has been verified on a test rig.It is experimentally confirmed that this research provides an important basis for achieving an optimal regulation of spring load distribution for multiple types of railway vehicles.

Influence of Shim Layers on Progressive Failure of a Composite Componentin Composite-Aluminum Bolted Joint in Aerospace Structural Assembly

The influence of varying shim layers on the progressive damage/failure of a composite component in a bolted composite-aluminum aerospace structural assembly was investigated using a non-linear three-dimensional(3 D)structural solid elements assembled model of a carbon fiber-reinforced polymer(CFRP)-aluminum single-lap joint with a titanium(Ti-6 Al-4 V)fastener and a washer generated with the commercial finite element(FE)software package,ABAQUS/Standard.A progressive failure algorithm written in Fortran code with a set of appropriate degradation rules was incorporated as a user subroutine in ABAQUS to simulate the non-linear damage behavior of the composite component in the composite-aluminum bolted aerospace structure.The assembled 3 DFE model simulated,as well as the specimen for the experimental testing consisted of a carbon-epoxy IMS-977-2 substrate,aluminum alloy 7075-T651 substrate,liquid shim(Hysol EA 9394),solid peelable fiberglass shim,a titanium fastener,and a washer.In distinction to previous investigations,the influence of shim layers(liquid shim and solid peelable fiberglass shim)inserted in-between the faying surfaces(CFRP and aluminum alloy substrates)were investigated by both numerical simulations and experimental work.The simulated model and test specimens conformed to the standard test configurations for both civil and military standards.The numerical simulations correlated well with the experimental results and it has been found that:(1)The shimming procedure as agreed upon by the aerospace industry for the resolution of assembly gaps in bolted joints for composite materials is the same for a composite-aluminum structure;liquid shim series(0.3,0.5 and 0.7 mm thicknesses)prolonged the service life of the composite component whereas a solid peelable fiberglass shim most definitely had a better influence on the 0.9 assembly gap compared with the liquid shim;(2)The shim layers considerably influenced the structural strength of the composite component by delaying its ultimate failure thereby increasing its service life;and(3)Increasing the shim layer′s thickness led to a significant corresponding effect on the stiffness but with minimal effect on the ultimate load.

A novel approach to designing cylindrical-surface shim coils for a superconducting magnet of magnetic resonance imaging

For a superconducting magnet of magnetic resonance imaging （MRI）, the novel approach presented in this paper allows the design of cylindrical gradient and shim coils of finite length. The method is based on identification of the weighting of harmonic components in the current distribution that will generate a magnetic field whose z-component follows a chosen spherical harmonic function. Mathematical expressions which relate the harmonic terms in the cylin- drical current distribution to spherical harmonic terms in the field expansion are established. Thus a simple matrix inversion approach can be used to design a shim coil of any order pure harmonic. The expressions providing a spherical harmonic decomposition of the field components produced by a particular cylindrical current distribution are novel. A stream function was applied to obtain the discrete wire distribution on the cylindrical-surface. This method does not require the setting of the target-field points. The discussion referring to matrix equations in terms of condition numbers proves that this novel approach has no ill-conditioned problems. The results also indicate that it can be used to design cylindrical-surface shim coils of finite length that will generate a field variation which follows a particular spherical harmonic over a reasonably large-sized volume.

Design and field measurement of a dipole magnet for a newly developed superconducting proton cyclotron beamline

The design, field quality optimization, multipole field analysis, and field measurement of a dipole for a newly developed superconducting proton cyclotron(SC200) beamline are presented in this paper. The maximum magnetic field of the dipole is 1.35 T; the bending radius is 1.6 m with a proton beam energy in the range of70–200 Me V. The magnetic field was calculated with 2 D and 3 D simulations, and measured with a Hall mapping system. The pole shim and end chamfer were optimized to improve the field quality. Based on the simulated results,the multipole field components in the good-field region were studied to evaluate the field quality. The results showed that the field quality is better than ± 5 × 10^(-4) at1.35 T with shimming and chamfering. For the transverse field homogeneity, the third-order(B3) and fifth-order(B5)components should be controlled with symmetrical shims.The second-order(B2) component was the main disturbance for the integral field homogeneity; it could be improved with an end chamfer. The magnet manufacturing and field measurement were performed in this project. The measurement results demonstrated that the magnetic design and field quality optimization of the 45° dipole magnet can achieve the desired high field quality and satisfy the physical requirements.

Active ferromagnetic shimming of the permanent magnet for magnetic resonance imaging scanner

This paper presents an approach of active ferromagnetic shimming for C-type permanent magnetic resonance imaging （MRI） magnet. It is designed to reduce inhomogeneity of magnetostatic field of C-type permanent magnet to meet the stringent requirement for MRI applications. An optimal configuration （locations and thicknesses） of active ferromagnetic pieces is generated through calculation according to the initial field map and the demanded final homo- geneity specifications. This approach uses a minimisation technique which makes the sum of squared magnetic moment minimum to restrict the amount of the active ferromagnetic material used and the maximal thickness of pieces stacked at each hole location in the shimming hoards. Simulation and experimental results verify that the method is valid and efficient.

Shim coil design for Halbach magnet by equivalent magnetic dipole method

Low-field nuclear magnetic resonance magnet（2 MHz） is required for rock core analysis. However, due to its low field strength, it is hard to achieve a high uniform B0 field only by using the passive shimming. Therefore, active shimming is necessarily used to further improve uniformity for Halbach magnet. In this work, an equivalent magnetic dipole method is presented for designing shim coils. The minimization of the coil power dissipation is considered as an optimal object to minimize coil heating effect, and the deviation from the target field is selected as a penalty function term. The lsqnonlin optimization toolbox of MATLAB is used to solve the optimization problem. Eight shim coils are obtained in accordance with the contour of the stream function. We simulate each shim coil by ANSYS Maxwell software to verify the validity of the designed coils. Measurement results of the field distribution of these coils are consistent with those of the target fields.The uniformity of the B0 field is improved from 114.2 ppm to 26.9 ppm after using these shim coils.

Dynamic subsidence basins in coal mines based on rock mass rheological theory

In order to investigate the surface deformation caused by coal mining and to reduce environmental damage, more accurate information of dynamic subsidence basins, caused by coal mining, is needed. Based on theological theory, we discuss surface deformation mechanism of dynamic subsidence on the assumption that both the roof and the coal seam are visco-elastic media, put forward the idea that the principle of surface deformation is similar to that of roofs, except for their parameters. Therefore, a surface deforma- tion equation can be obtained, given the equation of the roof deformation derived.from using a HIM rhe- ological model. In the end, we apply the equation of surface deformation as a practical subsidence prediction in a coal mine. Given the theologic properties of a rock mass, the results of our research of a dynamic subsidence basin can predict the development of surface deformation as a function of time, which is more important than the ultimate subsidence itself. The results indicate that using rheological theory to calculate the deformation of a dynamic subsidence basin is suitable and provides some reference for surface deformation of dynamic subsidence basins.

Active shim coils design for Halbach magnet based on inverse boundary element method

With advantages of small volume,high field strength,and compact stray field,the Halbach array magnet is of great potential in desktop NMR applications.However,field inhomogeneity poses a main obstacle to its applications.Active shimming is necessary for improving the field homogeneity.An active shim coil design method for cylindrical Halbach magnet based on inverse boundary element method(iBEM)is introduced in this work.Shim coils targeting 1st~3rd and Z4/Z5/Z6 spherical harmonic(SH)terms were designed with constraints of field accuracy,resistance,inductance,and current density.Wire loops and symmetric property influence were discussed to further improve the performance of high-order shim coils.Finally,with the prototype of the shim coils constructed,field pattern and SH transformation proved that the coils designed could fit the target SH distribution,though contamination from low-order components existed in highorder terms.A practical shimming experiment on the Halbach magnet has improved the homogeneity from 40.3 ppm to 3.8 ppm in radius 2.5 mm,height 5 mm cylindrical sample space,verifying the coils'compensation ability.This work provides a flexible inverse coil design method for cylindrical Halbach magnet and discusses the high-order shim coil design and implementation,which is potential in nuclear magnetic resonance applications based on Halbach magnet arrays.

基于Shim6机制的最佳接入方式

随着IPv6的逐渐部署,使用多宿主(Multihoming)也将成为一种普遍的现象,虽然现有解决IPv6多宿主的方法很多,但Shim6方案已被认为是目前解决IPv6多宿主问题的最好方案。但是目前现有的Shim6机制还不够完善,有些地方还存在缺陷,文章提出一种基于Shim6机制的最佳接入方式,该方式不仅能够减少切换的时延、节省用户资源消耗,还能根据用户自定义的策略选择"最佳"接入网,提升用户体验(QoE)。

Slice-Selective Transmit Array Pulses for Improvement in Excitation Uniformity and Reduction of SAR

To overcome challenges of inhomogeneous transmit B1 distribution and high specific energy absorption rate (SAR) in MRI, we compare slice-selective array-optimized composite pulse and RF shimming designed to both improve B1 uniformity and reduce SAR using an 8-channel transmit head array loaded with a head model at various RF pulse excitation times, and compare results with standard quadrature voltage distribution at 3T (128 MHz) and 7T (300 MHz). The excitation uniformity was estimated throughout the 3D brain region and SAR was calculated for the whole head. The optimized composite pulse could produce significantly better homogeneity and significantly better homogeneity when SAR was not constrained, and both significantly better homogeneity and lower SAR when the pulse duration was allowed to be twice that of the quadrature or RF shimmed pulse. When the total pulse durations were constrained to the same length, the relative advantages of the optimized composite pulse for producing better homogeneity and lower SAR simultaneously were diminished. Using the optimization results, the slice-selective composite pulse sequence was implemented on a 3D MRI simulator currently under development, and showed both effective slice selection and improvement in excitation uniformity compared to a conventional quadrature driving method.

SARAH SHIM 甜美梦幻的秀场

韩国设计师带来了粉粉的皮草,可爱的蓬裙,飘逸的长裙,所有的主题围绕公主这个词汇展开,为女孩们带来一场甜美梦幻的秀场。

Mapping System,Magnetic Measurement and Shimming in CRM Cyclotron

The Central Region Model(CRM)is a compact H^- cyclotron.Because of the intrinsic asymmetry of the magnet,its machining and assembly are very complicated.To guarantee the magnet field distribution,it is necessary to measure and shim the magnetic field.This paper presents a study on the design and use of the mapping system based on the Hall Effect and the re-machining of shimming bars after analyzing the magnetic field measurement data to achieve the isochronous field and good vertical focusing frequency.The method to effectively reduce the amplitude of the 1st harmonic by shimming bars ls also introduced.

The physics design of magnet in 14 MeV cyclotron

The 14 MeV, 400 μA compact cyclotron is under construction at China Institute of Atomic Energy (CIAE). The design of main magnet and the result of beam dynamics in the cyclotron will be described in this paper, including the choice of main parameters of magnet, the method of shimming isochronous field in the compact cyclotron and optimization of the magnetic field in central region. The beam will be accelerated to 14.6 MeV by optimizing the magnet structure.

Passive shimming based on mixed integer programming for MRI magnet

A mathematical model based on mixed integer programming is presented in this paper for the passive shimming of magnet in magnetic resonance imaging(MRI) scanner.In this model,the magnetic field inhomogeneity tolerance and the central value of the magnetic field after shimming are programmed together with the volume of each shim piece as the variables,which increases the degree of freedom and guarantees a better solution.The magnetic field inhomogeneity tolerance after shimming with a weighting coefficient and the total volume of shim pieces are both contained in the objective function of the model.By assigning different values to the weighting coefficient in the objective function,different shimming plans with different emphases can be obtained.A simulation test has been carried out on a small permanent magnet with frame structure.Several solutions are given and compared in this paper,which indicates that a practical shimming plan can be obtained quickly by solving this model.