Multi-layer pressure vessels are widely used in every field of high pressure technology.For the purpose of enhancing a vessels＇ load bearing capacity,a beneficial process like shrink-fit is usually employed.However,f...Multi-layer pressure vessels are widely used in every field of high pressure technology.For the purpose of enhancing a vessels＇ load bearing capacity,a beneficial process like shrink-fit is usually employed.However,few documents on optimum design for multi-layer shrink-fit vessels made of different strength materials can be found,available data are mainly on two-layer vessels.In this paper,an optimum design approach is developed for shrink-fit multi-layer vessels under ultrahigh pressure by using different materials.Maximum shear stress theory is applied as design criteria.The inner and outer radii of a multi-layer vessel,as well as the material of each layer,are assumed to be known.The optimization mathematical model is,thereby,built.Lagrange multipliers method is required to obtain the optimal design formula of wall ratio（ratio of outer to inner radii） of each layer,from which the optimum formulas of shrinkage pressure and radial interference are derived with the superposition principle employed.These formulas are applicable for the optimization design of all multi-layer vessels made of different materials,or same materials.The formulas of the limit working pressure and the contact pressure show that the optimum wall ratio of each layer and limit working pressure are only related to all selected material strength and unrelated to the position of the layer placement in the vessel.However,shrinkage pressure is related to the position of the layer placement in the vessel.Optimization design of an open ended shrink-fit three-layer vessel using different materials and comparisons proved that the optimized multi-layer vessels have outstanding characteristics of small radial interference and are easier for assembly.When the stress of each layer is distributed more evenly and appropriately,the load bearing capability and safety of vessels are enhanced.Therefore,this design is material-saving and cost-effective,and has prospect of engineering application.展开更多
Though the lengthened shrink-fit holder (LSFH) is widely applied in high speed milling of the parts characterized by deep cavities at present, its design and selection mainly depends on the experience and lacks a corr...Though the lengthened shrink-fit holder (LSFH) is widely applied in high speed milling of the parts characterized by deep cavities at present, its design and selection mainly depends on the experience and lacks a correct theoretical guidance. In this paper, attention is focus on the radial grip rigidity of the matching of LSFH and cutter in high speed milling. Based on the experiment modal analysis (EMA) technique, an accurate finite element model of the matching of LSFH and cutter is established firstly. Subsequently, the influence of different interference, grip length and spindle speed on the grip rigidity of LSFH are analyzed. The analysis results show that there is a reasonable interference and grip length between the LSFH and cutter so that to have a steepless grip and have a good radial grip rigidity and at the same time to avoid the strength of LSFH to exceed it’s yield limit which will reduce the precision and service life of LSFH, besides when spindle speed reach a extension the weakening influence of the centrifugal force on the radial grip rigidity of the matching of LSFH and cutter should been taken into account. Finally, the finite element analysis results are verified based on the construction of measurement method of the grip rigidity and the results fit very well. The studies provide a theoretical basis for the design, selection and the serialization and standardization of the matching of LSFH and cutter.展开更多
Structural integrity of the flywheel of reactor coolant pump is important for safe operation of a nuclear power plant. A shrink-fit multi-ring flywheel is designed with a fall-off function, i.e., it will separate from...Structural integrity of the flywheel of reactor coolant pump is important for safe operation of a nuclear power plant. A shrink-fit multi-ring flywheel is designed with a fall-off function, i.e., it will separate from the shaft at a designed fall-off rotation speed, which is determined by the assembly process and the gravity. However, the two factors are ignored in the analytical method based on the Lame's equation. In this work, we conducted fall-off experiments to analyze the two factors and used the experimental data to verify the validity of the analytical method and the finite element method(FEM). The results show that FEM performs better than the analytical method in designing the falloff function of the flywheel, though FEM cannot successfully predict the strain variation with the rotational speed.展开更多
基金supported by Key Scientific Research Project of Baoji University of Arts and Sciences of China (Grant No.ZK0727)Shanxi Provincial Special Foundation Project of Key Discipline Construction of China
文摘Multi-layer pressure vessels are widely used in every field of high pressure technology.For the purpose of enhancing a vessels＇ load bearing capacity,a beneficial process like shrink-fit is usually employed.However,few documents on optimum design for multi-layer shrink-fit vessels made of different strength materials can be found,available data are mainly on two-layer vessels.In this paper,an optimum design approach is developed for shrink-fit multi-layer vessels under ultrahigh pressure by using different materials.Maximum shear stress theory is applied as design criteria.The inner and outer radii of a multi-layer vessel,as well as the material of each layer,are assumed to be known.The optimization mathematical model is,thereby,built.Lagrange multipliers method is required to obtain the optimal design formula of wall ratio（ratio of outer to inner radii） of each layer,from which the optimum formulas of shrinkage pressure and radial interference are derived with the superposition principle employed.These formulas are applicable for the optimization design of all multi-layer vessels made of different materials,or same materials.The formulas of the limit working pressure and the contact pressure show that the optimum wall ratio of each layer and limit working pressure are only related to all selected material strength and unrelated to the position of the layer placement in the vessel.However,shrinkage pressure is related to the position of the layer placement in the vessel.Optimization design of an open ended shrink-fit three-layer vessel using different materials and comparisons proved that the optimized multi-layer vessels have outstanding characteristics of small radial interference and are easier for assembly.When the stress of each layer is distributed more evenly and appropriately,the load bearing capability and safety of vessels are enhanced.Therefore,this design is material-saving and cost-effective,and has prospect of engineering application.
基金supported by National Hi-tech Research and Development Program of China (863 Program, Grant No. 2009AA44302)Scientific Research Fund of Hunan Provincial Education Department, China (Grant No. 10C1259)+2 种基金Hunan Provincial Planned Science and Technology Project of China (Grant No. 2011FJ3231)National Natural Science Foundation of China (Grant No. 51005194)Open Innovation Platform of Hunan College Fund, China (Grant No. 10K063)
文摘Though the lengthened shrink-fit holder (LSFH) is widely applied in high speed milling of the parts characterized by deep cavities at present, its design and selection mainly depends on the experience and lacks a correct theoretical guidance. In this paper, attention is focus on the radial grip rigidity of the matching of LSFH and cutter in high speed milling. Based on the experiment modal analysis (EMA) technique, an accurate finite element model of the matching of LSFH and cutter is established firstly. Subsequently, the influence of different interference, grip length and spindle speed on the grip rigidity of LSFH are analyzed. The analysis results show that there is a reasonable interference and grip length between the LSFH and cutter so that to have a steepless grip and have a good radial grip rigidity and at the same time to avoid the strength of LSFH to exceed it’s yield limit which will reduce the precision and service life of LSFH, besides when spindle speed reach a extension the weakening influence of the centrifugal force on the radial grip rigidity of the matching of LSFH and cutter should been taken into account. Finally, the finite element analysis results are verified based on the construction of measurement method of the grip rigidity and the results fit very well. The studies provide a theoretical basis for the design, selection and the serialization and standardization of the matching of LSFH and cutter.
基金supported by the National Natural Science Foundation of China(No.51576125)
文摘Structural integrity of the flywheel of reactor coolant pump is important for safe operation of a nuclear power plant. A shrink-fit multi-ring flywheel is designed with a fall-off function, i.e., it will separate from the shaft at a designed fall-off rotation speed, which is determined by the assembly process and the gravity. However, the two factors are ignored in the analytical method based on the Lame's equation. In this work, we conducted fall-off experiments to analyze the two factors and used the experimental data to verify the validity of the analytical method and the finite element method(FEM). The results show that FEM performs better than the analytical method in designing the falloff function of the flywheel, though FEM cannot successfully predict the strain variation with the rotational speed.
