By employing sintering additives of Li2CO3 and Y2O3,porous Si3N4 ceramics are prepared after experiencing the processes of sintering and post-vacuum heat treatment at 1680 and 1550°C,respectively.The experimental...By employing sintering additives of Li2CO3 and Y2O3,porous Si3N4 ceramics are prepared after experiencing the processes of sintering and post-vacuum heat treatment at 1680 and 1550°C,respectively.The experimental results demonstrate the completed phase transformation fromαtoβ-Si3N4 in Si3N4 ceramic samples with a amount of 1.60 wt%Li2CO3(0.65 wt%Li2O)and 0.33 wt%Y2O3 additives.The as-synthesized porous Si3N4 ceramics exhibit high flexural strength((126.7±2.7)MPa)and high open porosity of 50.4%at elevated temperature(1200°C).These results are attributed to the significant role of added Li2CO3 as sintering additive,where the volatilization of intergranular glassy phase occurs during sintering process.Therefore,porous Si3N4 ceramics with desired mechanical property prepared by altering the addition of sintering additives demonstrate their great potential as a promising candidate for high temperature applications.展开更多
The microstructures and crack propagating characteristic of Si 3N 4 (μ)/SiC (n, w) composite ceramic were studied with AEM. The Si 3N 4 (μ)/SiC (n, w) composite ceramic consists of β Si 3N 4, β SiC, a smal...The microstructures and crack propagating characteristic of Si 3N 4 (μ)/SiC (n, w) composite ceramic were studied with AEM. The Si 3N 4 (μ)/SiC (n, w) composite ceramic consists of β Si 3N 4, β SiC, a small amount of α Si 3N 4 and α SiC, and amorphous phase. Most of Si 3N 4 grains were equiaxed crystal and also there were some bulky columnar ones. Most of SiC particles and SiC whiskers distributed at the Si 3N 4 grain boundaries and a few of smaller SiC particles in the Si 3N 4 grains. Most of amorphous structure was in the junction of several Si 3N 4 grains and thin amorphous layer was observed only at a few of Si 3N 4 boundaries. Failured cracks propagated mainly along the boundaries of the Si 3N 4 grains and partially passed through Si 3N 4 grains. The path of crack propagating might change, branching and twisting of the cracks might occur when the expanding crack meet the SiC particle and/or SiC whisker. Effect of the microstructure on strength and toughness of the composite ceramic was briefly discussed.展开更多
Aiming at developing novel microwave-transparent ceramics with low dielectric loss, high thermal conductivity and high strength, Si3Na-AIN （30%, mass fraction） composite ceramics with La203 as sintering additive wer...Aiming at developing novel microwave-transparent ceramics with low dielectric loss, high thermal conductivity and high strength, Si3Na-AIN （30%, mass fraction） composite ceramics with La203 as sintering additive were prepared by hot-pressing at 1 800 ℃ and subsequently annealed at 1 450 ℃ and 1 850 ℃ for 2 h and 4 h, respectively. The materials were characterized by XRD and SEM. The effect of annealing process on the phase composition, sintering performance, microstructure, bending strength, dielectric loss and thermal conductivity of the materials was investigated. The results showed that both annealing at 1 850 ℃ and 1 450 ℃ promoted the phase transformation of α-Si3N4 to β-Si3N4. After annealing at 1 850 ℃, grain growth to a certain extent occurred in the materials. Especially, the elongated β-Si3N4 grains showed a slight increase in diameter from 0.2 μm to 0.6 μm approximately and a decrease in aspect ratio. As a result, as the annealing time increased to 4 h, the bending strength declined from 456 MPa to 390 MPa, whereas the dielectric loss decreased to 2.15× 10^-3 and the thermal conductivity increased to 16.3 W/（m.K） gradually. When annealed at 1 450 ℃, increasing the annealing time to 4 h significantly promoted the crystallization of glassy phase to La2Si6N803 phase in the materials, which led to the increase in bending strength to 619 MPa and thermal conductivity to 15.9 W/（m·K）, respectively, and simultaneously the decrease in dielectric loss to 1.53× 10^-3.展开更多
The effect of rare earth oxides Y 2O 3 or CeO 2 on sintering properties of Si 3N 4 ceramics was studied and the mechanism of assisting action during sintering was analyzed. The results indicate that the best sint...The effect of rare earth oxides Y 2O 3 or CeO 2 on sintering properties of Si 3N 4 ceramics was studied and the mechanism of assisting action during sintering was analyzed. The results indicate that the best sintering properties appear in Si 3N 4 ceramics with 5% Y 2O 3 or 8% CeO 2. Secondary crystallites are formed at grain boundaries after heat treatment, which decreases the amount of glass phase and contributes to the improvement of high temperature mechanical properties of silicon nitride.展开更多
基金Project(202045007)supported by the Start-up Funds for Outstanding Talents in Central South University,China。
文摘By employing sintering additives of Li2CO3 and Y2O3,porous Si3N4 ceramics are prepared after experiencing the processes of sintering and post-vacuum heat treatment at 1680 and 1550°C,respectively.The experimental results demonstrate the completed phase transformation fromαtoβ-Si3N4 in Si3N4 ceramic samples with a amount of 1.60 wt%Li2CO3(0.65 wt%Li2O)and 0.33 wt%Y2O3 additives.The as-synthesized porous Si3N4 ceramics exhibit high flexural strength((126.7±2.7)MPa)and high open porosity of 50.4%at elevated temperature(1200°C).These results are attributed to the significant role of added Li2CO3 as sintering additive,where the volatilization of intergranular glassy phase occurs during sintering process.Therefore,porous Si3N4 ceramics with desired mechanical property prepared by altering the addition of sintering additives demonstrate their great potential as a promising candidate for high temperature applications.
文摘The microstructures and crack propagating characteristic of Si 3N 4 (μ)/SiC (n, w) composite ceramic were studied with AEM. The Si 3N 4 (μ)/SiC (n, w) composite ceramic consists of β Si 3N 4, β SiC, a small amount of α Si 3N 4 and α SiC, and amorphous phase. Most of Si 3N 4 grains were equiaxed crystal and also there were some bulky columnar ones. Most of SiC particles and SiC whiskers distributed at the Si 3N 4 grain boundaries and a few of smaller SiC particles in the Si 3N 4 grains. Most of amorphous structure was in the junction of several Si 3N 4 grains and thin amorphous layer was observed only at a few of Si 3N 4 boundaries. Failured cracks propagated mainly along the boundaries of the Si 3N 4 grains and partially passed through Si 3N 4 grains. The path of crack propagating might change, branching and twisting of the cracks might occur when the expanding crack meet the SiC particle and/or SiC whisker. Effect of the microstructure on strength and toughness of the composite ceramic was briefly discussed.
基金Project(50872052) supported by the National Natural Science Foundation of ChinaProject(2009AA05Z313) supported by the National High Technology Research and Development Program of ChinaProject supported by the Commission of Science,Technology and Industry for National Defence,China
文摘Aiming at developing novel microwave-transparent ceramics with low dielectric loss, high thermal conductivity and high strength, Si3Na-AIN （30%, mass fraction） composite ceramics with La203 as sintering additive were prepared by hot-pressing at 1 800 ℃ and subsequently annealed at 1 450 ℃ and 1 850 ℃ for 2 h and 4 h, respectively. The materials were characterized by XRD and SEM. The effect of annealing process on the phase composition, sintering performance, microstructure, bending strength, dielectric loss and thermal conductivity of the materials was investigated. The results showed that both annealing at 1 850 ℃ and 1 450 ℃ promoted the phase transformation of α-Si3N4 to β-Si3N4. After annealing at 1 850 ℃, grain growth to a certain extent occurred in the materials. Especially, the elongated β-Si3N4 grains showed a slight increase in diameter from 0.2 μm to 0.6 μm approximately and a decrease in aspect ratio. As a result, as the annealing time increased to 4 h, the bending strength declined from 456 MPa to 390 MPa, whereas the dielectric loss decreased to 2.15× 10^-3 and the thermal conductivity increased to 16.3 W/（m.K） gradually. When annealed at 1 450 ℃, increasing the annealing time to 4 h significantly promoted the crystallization of glassy phase to La2Si6N803 phase in the materials, which led to the increase in bending strength to 619 MPa and thermal conductivity to 15.9 W/（m·K）, respectively, and simultaneously the decrease in dielectric loss to 1.53× 10^-3.
文摘The effect of rare earth oxides Y 2O 3 or CeO 2 on sintering properties of Si 3N 4 ceramics was studied and the mechanism of assisting action during sintering was analyzed. The results indicate that the best sintering properties appear in Si 3N 4 ceramics with 5% Y 2O 3 or 8% CeO 2. Secondary crystallites are formed at grain boundaries after heat treatment, which decreases the amount of glass phase and contributes to the improvement of high temperature mechanical properties of silicon nitride.
