The effect of nitric oxide（NO） annealing on charge traps in the oxide insulator and transition layer in n-type4H–Si C metal–oxide–semiconductor（MOS） devices has been investigated using the time-dependent bias s...The effect of nitric oxide（NO） annealing on charge traps in the oxide insulator and transition layer in n-type4H–Si C metal–oxide–semiconductor（MOS） devices has been investigated using the time-dependent bias stress（TDBS）,capacitance–voltage（C–V）,and secondary ion mass spectroscopy（SIMS）.It is revealed that two main categories of charge traps,near interface oxide traps（Nniot） and oxide traps（Not）,have different responses to the TDBS and C–V characteristics in NO-annealed and Ar-annealed samples.The Nniotare mainly responsible for the hysteresis occurring in the bidirectional C–V characteristics,which are very close to the semiconductor interface and can readily exchange charges with the inner semiconductor.However,Not is mainly responsible for the TDBS induced C–V shifts.Electrons tunneling into the Not are hardly released quickly when suffering TDBS,resulting in the problem of the threshold voltage stability.Compared with the Ar-annealed sample,Nniotcan be significantly suppressed by the NO annealing,but there is little improvement of Not.SIMS results demonstrate that the Nniotare distributed within the transition layer,which correlated with the existence of the excess silicon.During the NO annealing process,the excess Si atoms incorporate into nitrogen in the transition layer,allowing better relaxation of the interface strain and effectively reducing the width of the transition layer and the density of Nniot.展开更多
A three-terminal silicon-based light emitting device is proposed and fabricated in standard 0.35 μm complementary metal-oxide-semiconductor technology. This device is capable of versatile working modes： it can emit ...A three-terminal silicon-based light emitting device is proposed and fabricated in standard 0.35 μm complementary metal-oxide-semiconductor technology. This device is capable of versatile working modes： it can emit visible to near infra-red （NIR） light （the spectrum ranges from 500 nm to 1000 nm） in reverse bias avalanche breakdown mode with working voltage between 8.35 V-12 V and emit NIR light （the spectrum ranges from 900 nm to 1300 nm） in the forward injection mode with working voltage below 2 V. An apparent modulation effect on the light intensity from the polysilicon gate is observed in the forward injection mode. Furthermore, when the gate oxide is broken down, NIR light is emitted from the polysilicon/oxide/silicon structure. Optoelectronic characteristics of the device working in different modes are measured and compared. The mechanisms behind these different emissions are explored.展开更多
SiC MOSFET因其高击穿电压、高开关速度、低导通损耗等性能优势而被广泛应用于各类电力电子变换器中。然而,由于其短路耐受时间仅为2~7μs,且随母线电压升高而缩短,快速可靠的短路保护电路已成为其推广应用的关键技术之一。为应对不同...SiC MOSFET因其高击穿电压、高开关速度、低导通损耗等性能优势而被广泛应用于各类电力电子变换器中。然而,由于其短路耐受时间仅为2~7μs,且随母线电压升高而缩短,快速可靠的短路保护电路已成为其推广应用的关键技术之一。为应对不同母线电压下的Si C MOSFET短路故障,文中提出一种基于漏源电压积分的自适应快速短路保护方法(drain-sourcevoltageintegration-basedadaptivefast short-circuit protection method,DSVI-AFSCPM),研究所提出的DSVI-AFSCPM在硬开关短路(hardswitchingfault,HSF)和负载短路(fault under load,FUL)条件下的保护性能,进而研究不同母线电压对DSVI-AFSCPM的作用机理。同时,探究Si CMOSFET工作温度对其响应速度的影响。最后,搭建实验平台,对所提出的DSVI-AFSCPM在发生硬开关短路和负载短路时不同母线电压、不同工作温度下的保护性能进行实验测试。实验结果表明,所提出的DSVI-AFSCPM在不同母线电压下具有良好的保护速度自适应性,即母线电压越高,短路保护速度越快,并且其响应速度受Si CMOSFET工作温度影响较小,两种短路工况下工作温度从25℃变化到125℃,短路保护时间变化不超过90 ns。因此,该文为Si CMOSFET在不同母线电压下的可靠使用提供一定技术支撑。展开更多
在评估和优化半导体器件开关瞬态特性领域,解析模型因具有简单、直观、应用便捷等优点得到广泛研究。相较同等功率等级的硅基功率器件,碳化硅(silicon carbide,SiC)金属氧化物半导体场效应晶体管(metal-oxide-semiconductor field effec...在评估和优化半导体器件开关瞬态特性领域,解析模型因具有简单、直观、应用便捷等优点得到广泛研究。相较同等功率等级的硅基功率器件,碳化硅(silicon carbide,SiC)金属氧化物半导体场效应晶体管(metal-oxide-semiconductor field effect transistor,MOSFET)可以应用于更高开关速度,其开关瞬态特性更为复杂,开关瞬态解析建模也更加困难。该文总结现有的针对SiC MOSFET与二极管换流对的开关瞬态解析建模方法,在建模过程中依次引入各种简化假设,按照简化程度由低到高的顺序,梳理解析建模的逐步简化过程。通过对比,评估各模型的优缺点以及适用场合,对其中准确性、实用性都较强的分段线性模型进行详细介绍;之后,对开关瞬态建模中关键参数的建模方法进行总结与评价;最后,指出现有SiC MOSFET开关瞬态解析模型中存在的问题,并对其未来发展给出建议。展开更多
In this paper, the normally-off N-channel lateral 4H-SiC metal-oxide-semiconductor field-effect transistors （MOSF- FETs） have been fabricated and characterized. A sandwich- （nitridation-oxidation-nitridation） type...In this paper, the normally-off N-channel lateral 4H-SiC metal-oxide-semiconductor field-effect transistors （MOSF- FETs） have been fabricated and characterized. A sandwich- （nitridation-oxidation-nitridation） type process was used to grow the gate dielectric film to obtain high channel mobility. The interface properties of 4H-SiC/SiO2 were examined by the measurement of HF l-V, G-V, and C-V over a range of frequencies. The ideal C-V curve with little hysteresis and the frequency dispersion were observed. As a result, the interface state density near the conduction band edge of 4H-SiC was reduced to 2 x 1011 eV-l.cm-2, the breakdown field of the grown oxides was about 9.8 MV/cm, the median peak field- effect mobility is about 32.5 cm2.V-1 .s-1, and the maximum peak field-effect mobility of 38 cm2-V-1 .s-1 was achieved in fabricated lateral 4H-SiC MOSFFETs.展开更多
Experiments and simulation studies on 283 MeV I ion induced single event effects of silicon carbide(SiC) metal–oxide–semiconductor field-effect transistors(MOSFETs) were carried out. When the cumulative irradiation ...Experiments and simulation studies on 283 MeV I ion induced single event effects of silicon carbide(SiC) metal–oxide–semiconductor field-effect transistors(MOSFETs) were carried out. When the cumulative irradiation fluence of the SiC MOSFET reached 5×10^(6)ion·cm^(-2), the drain–gate channel current increased under 200 V drain voltage, the drain–gate channel current and the drain–source channel current increased under 350 V drain voltage. The device occurred single event burnout under 800 V drain voltage, resulting in a complete loss of breakdown voltage. Combined with emission microscope, scanning electron microscope and focused ion beam analysis, the device with increased drain–gate channel current and drain–source channel current was found to have drain–gate channel current leakage point and local source metal melt, and the device with single event burnout was found to have local melting of its gate, source, epitaxial layer and substrate. Combining with Monte Carlo simulation and TCAD electrothermal simulation, it was found that the initial area of single event burnout might occur at the source–gate corner or the substrate–epitaxial interface, electric field and current density both affected the lattice temperature peak. The excessive lattice temperature during the irradiation process appeared at the local source contact, which led to the drain–source channel damage. And the excessive electric field appeared in the gate oxide layer, resulting in drain–gate channel damage.展开更多
基金Project supported by the National Natural Science Foundation of China(Grant Nos.61404098 and 61274079)the Doctoral Fund of Ministry of Education of China(Grant No.20130203120017)+2 种基金the National Key Basic Research Program of China(Grant No.2015CB759600)the National Grid Science&Technology Project,China(Grant No.SGRI-WD-71-14-018)the Key Specific Project in the National Science&Technology Program,China(Grant Nos.2013ZX02305002-002 and 2015CB759600)
文摘The effect of nitric oxide（NO） annealing on charge traps in the oxide insulator and transition layer in n-type4H–Si C metal–oxide–semiconductor（MOS） devices has been investigated using the time-dependent bias stress（TDBS）,capacitance–voltage（C–V）,and secondary ion mass spectroscopy（SIMS）.It is revealed that two main categories of charge traps,near interface oxide traps（Nniot） and oxide traps（Not）,have different responses to the TDBS and C–V characteristics in NO-annealed and Ar-annealed samples.The Nniotare mainly responsible for the hysteresis occurring in the bidirectional C–V characteristics,which are very close to the semiconductor interface and can readily exchange charges with the inner semiconductor.However,Not is mainly responsible for the TDBS induced C–V shifts.Electrons tunneling into the Not are hardly released quickly when suffering TDBS,resulting in the problem of the threshold voltage stability.Compared with the Ar-annealed sample,Nniotcan be significantly suppressed by the NO annealing,but there is little improvement of Not.SIMS results demonstrate that the Nniotare distributed within the transition layer,which correlated with the existence of the excess silicon.During the NO annealing process,the excess Si atoms incorporate into nitrogen in the transition layer,allowing better relaxation of the interface strain and effectively reducing the width of the transition layer and the density of Nniot.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.60536030,61036002,60776024,60877035 and 61036009)National High Technology Research and Development Program of China(Grant Nos.2007AA04Z329 and 2007AA04Z254)
文摘A three-terminal silicon-based light emitting device is proposed and fabricated in standard 0.35 μm complementary metal-oxide-semiconductor technology. This device is capable of versatile working modes： it can emit visible to near infra-red （NIR） light （the spectrum ranges from 500 nm to 1000 nm） in reverse bias avalanche breakdown mode with working voltage between 8.35 V-12 V and emit NIR light （the spectrum ranges from 900 nm to 1300 nm） in the forward injection mode with working voltage below 2 V. An apparent modulation effect on the light intensity from the polysilicon gate is observed in the forward injection mode. Furthermore, when the gate oxide is broken down, NIR light is emitted from the polysilicon/oxide/silicon structure. Optoelectronic characteristics of the device working in different modes are measured and compared. The mechanisms behind these different emissions are explored.
基金Projcet supported by the National Natural Science Foundation of China(Grant Nos.61404098,61176070,and 61274079)the Doctoral Fund of Ministry Education of China(Grant Nos.20110203110010 and 20130203120017)+1 种基金the National Key Basic Research Program of China(Grant No.2015CB75960the Key Specific Projects of Ministry of Education of China(Grant No.625010101)
文摘In this paper, the normally-off N-channel lateral 4H-SiC metal-oxide-semiconductor field-effect transistors （MOSF- FETs） have been fabricated and characterized. A sandwich- （nitridation-oxidation-nitridation） type process was used to grow the gate dielectric film to obtain high channel mobility. The interface properties of 4H-SiC/SiO2 were examined by the measurement of HF l-V, G-V, and C-V over a range of frequencies. The ideal C-V curve with little hysteresis and the frequency dispersion were observed. As a result, the interface state density near the conduction band edge of 4H-SiC was reduced to 2 x 1011 eV-l.cm-2, the breakdown field of the grown oxides was about 9.8 MV/cm, the median peak field- effect mobility is about 32.5 cm2.V-1 .s-1, and the maximum peak field-effect mobility of 38 cm2-V-1 .s-1 was achieved in fabricated lateral 4H-SiC MOSFFETs.
基金supported by the National Natural Science Foundation of China (Grant No. 12075065)。
文摘Experiments and simulation studies on 283 MeV I ion induced single event effects of silicon carbide(SiC) metal–oxide–semiconductor field-effect transistors(MOSFETs) were carried out. When the cumulative irradiation fluence of the SiC MOSFET reached 5×10^(6)ion·cm^(-2), the drain–gate channel current increased under 200 V drain voltage, the drain–gate channel current and the drain–source channel current increased under 350 V drain voltage. The device occurred single event burnout under 800 V drain voltage, resulting in a complete loss of breakdown voltage. Combined with emission microscope, scanning electron microscope and focused ion beam analysis, the device with increased drain–gate channel current and drain–source channel current was found to have drain–gate channel current leakage point and local source metal melt, and the device with single event burnout was found to have local melting of its gate, source, epitaxial layer and substrate. Combining with Monte Carlo simulation and TCAD electrothermal simulation, it was found that the initial area of single event burnout might occur at the source–gate corner or the substrate–epitaxial interface, electric field and current density both affected the lattice temperature peak. The excessive lattice temperature during the irradiation process appeared at the local source contact, which led to the drain–source channel damage. And the excessive electric field appeared in the gate oxide layer, resulting in drain–gate channel damage.
