Thermal analysis for brake disks of SiC/6061 Al alloy co-continuous composite for CRH3 during emergency braking considering airflow cooling

The mass of high-speed trains can be reduced using the brake disk prepared with SiC network ceramic frame reinforced 6061 aluminum alloy composite （SiCn/Al）. The thermal and stress analyses of SiCn/Al brake disk during emergency braking at a speed of 300 km/h considering airflow cooling were investigated using finite element （FE） and computational fluid dynamics （CFD） methods. All three modes of heat transfer （conduction, convection and radiation） were analyzed along with the design features of the brake assembly and their interfaces. The results suggested that the higher convection coefficients achieved with airflow cooling will not only reduce the maximum temperature in the braking but also reduce the thermal gradients, since heat will be removed faster from hotter parts of the disk. Airflow cooling should be effective to reduce the risk of hot spot formation and disc thermal distortion. The highest temperature after emergency braking was 461 °C and 359 °C without and with considering airflow cooling, respectively. The equivalent stress could reach 269 MPa and 164 MPa without and with considering airflow cooling, respectively. However, the maximum surface stress may exceed the material yield strength during an emergency braking, which may cause a plastic damage accumulation in a brake disk without cooling. The simulation results are consistent with the experimental results well.

Microstructure,interfacial reaction behavior,and mechanical properties of Ti_(3)AlC_(2)reinforced Al6061 composites

The interfacial reaction behavior of Al and Ti_(3)AlC_(2)at different pouring temperatures and its effect on the microstructure and mechanical properties of the composites were investigated.The results show that the addition of3.0 wt.%Ti_(3)AlC_(2)refines the average grain size ofα(Al)in the composite by 50.1%compared to Al6061 alloy.Morphological analyses indicate that an in-situ Al_(3Ti)transition layer of-180 nm in thickness is generated around the edge of Ti_(3)AlC_(2)at 720℃,forming a well-bonded Al-Al_(3Ti)interface.At this processing temperature,the ultimate tensile strength of A16061-3.0 wt.%Ti_(3)AlC_(2)composite is 199.2 MPa,an improvement of 41.5%over the Al6061 matrix.Mechanism analyses further elucidate that 720℃is favourable for forming the nano-sized transition layer at the Ti_(3)AlC_(2)edges.And,the thermal mismatch strengthening plays a dominant role in this state,with a strengthening contribution of about 74.8%.

Effect of porosity and interface structures on thermal and mechanical properties of SiC_p/6061Al composites with high volume fraction of SiC

50 vol.% SiCp/Al composites with high thermal and mechanical properties were successfully produced by spark plasma sintering technique. The influences of sintering temperature on the thermal conductivity, coefficient of thermal expansion and bending strength of the SiCp/Al composites were carefully investigated. The results show that the SiCp/Al composites sintered at 520℃ exhibits a thermal conductivity of 189 W/(m·K), a coefficient of thermal expansion (50.200℃) of 10.03×10^-6 K^-1 and a bending strength of 649 MPa. The high thermal and mechanical properties can be ascribed to the nearly full density and the well interfacial bonding between the alloy matrix and the SiC particles. This work provides a promising pathway for producing materials to meet the needs of high performance electronic packaging.

Relaxation of residual stresses in 20%SiC_w/6061Al composite as-extruded at high temperature

The residual stress in a 20%SiC w/6061Al composite as extruded was investigated by using X ray stress measurement method. It was found that, high residual stress existed in the composite and residual stress distribution in each direction are not uniform. Relaxation process of residual stress in the composite was dynamically measured during annealing at high temperature. It is verified that the relaxation of residual stress obeys the power law at high temperature. With the creep mechanism, the relaxation behavior of residual stresses at high temperature was analyzed. The results show that, the stress exponent and activation energy for stress relaxation of the composite are obviously higher than those of the matrix alloy.

Role of particle stimulated nucleation in recrystallization of hot extruded Al 6061/SiC_p composites

Studies on texture and microstructure evolution in hot extruded Al 6061 aluminium alloy reinforced with uncoated and nickel coated SiC p were carried out by electron backscattered diffraction technique.Textures of both the alloy and its composite with nickel coated SiC p do exhibit strong β fiber with its axis parallel to the direction of extrusion.In addition to the dominant cube texture（001） 100,fully recrystallized grains with partially equiaxed structure have been observed in the alloy reinforced with uncoated SiC p.The recrystallization texture of this composite can be attributed to the particle stimulated nucleation（PSN） due to the presence of SiC p with size less than 5 μm.Under these conditions,the low value of Zener-Hollomon,Z（～1012s-1） confirms that PSN is one of the dominant mechanisms for recrystallization and is governed by formation of deformation zone rather than stored energy.

Diffusion welding process and joint's microstructure behavior of SiC_w/6061Al composite

The rules such as process parameters affecting joint properties and theevolution principle of weld's microstructure have been researched by adopting diffusion weldingprocess to connect SiC_w/6061Al composite. Experimental results show that there exists a criticaltemperature region between solid and liquid phase line of SiC_w/6061Al composite, and the regionwill shrink with the increasing of welding pressure. When diffusion welding occurred under thecritical temperature region, welding joint exhibits bad property of bonding, and the matrix and thereinforcement can't bond effectively. When diffusion welding occurred in the critical temperatureregion, the strength of welding joint changes widely with the variation of welding temperature. Whenwelding temperature varies in 10 deg C, the strength of welding joint will change obviously. Onlywhen welding temperature is higher than the critical temperature region, stable joint properties canbe obtained. Simultaneously the matrix and the reinforcement has better interfacial bonded indiffusion welding interface, and no obvious interface reaction occurred, and thus diffusion weldingof SiC_w/6061 Al composite can be successfully realized.

ROLES OF ORIENTATION RELATIONSHIP AND RECRYSTALLIZATION IN SUPERPLASTICITY OF SiCw/6061Al COMPOSITE

ＲＯＬＥＳＯＦＯＲＩＥＮＴＡＴＩＯＮＲＥＬＡＴＩＯＮＳＨＩＰＡＮＤＲＥＣＲＹＳＴＡＬＬＩＺＡＴＩＯＮＩＮＳＵＰＥＲＰＬＡＳＴＩＣＩＴＹＯＦＳｉＣｗ／６０６１ＡｌＣＯＭＰＯＳＩＴＥ①ＧｕＷａｎｌｉ，ＰｅｎｇＨｕａｘｉｎ，ＬｉｕＺｏｎｇｒｏｎｇ，Ｗａｎｇ...

MICROSTRUCTURE AND PROPERTIES OF SiC_w/6061Al COMPOSITE The Author is now with Institute of Metal Research,Academia Sinica,China

The SiC_w/Al composite prepared by squeeze casting has a combination of superior room temperature specific strength and modulus together with excellent thermal properties.The extrusion can make an improvement on the strength and ductility of the composite from 582 MPa as squeeze casted up to 639 MPa,and on the transformation from isotropic to the anisotropic structure.This seems to be explained by the orientation of whiskers and the densification of dislocations in matrix.TEM observation indicates that the stacking fault is the usual planar defect on the SiC_w surface. composite;;SiC whisker;;Al alloy;;microstructure

An ecofriendly approach for corrosion control of 6061 Al-15%(v)SiC(P)composite and its base alloy

Corrosion inhibition characteristics of bio polymer dextran was studied for the corrosion control of 6061 Al-15%_((v)) SiC_((P)) composite and its base alloy in 1 mol·L^(-1) HCl. Standard electrochemical techniques such as potentiodynamic polarization(PDP) measurements and electrochemical impedance spectroscopy(EIS) method were adopted for corrosion rate measurement. Surface morphology was studied by scanning electron microscopy(SEM) and elemental mapping was done by energy dispersive X-ray(EDX) analysis. Suitable mechanism was proposed for corrosion and inhibition process. Results indicated that dextran acts as an excellent anticorrosive agent for the corrosion control of 6061 Al-15%_((v)) SiC_((P)) composite, with maximum inhibition efficiency of 91% for the concentration of 0.4 g·L^(-1) at 303 K. Dextran acted as a mixed type of inhibitor, and got physically adsorbed both on composite and base alloy by obeying Langmuir adsorption isotherm. Dextran is proved to be a green inhibitor with environmental and economic benefits.

Microstructure and thermophysical properties of SiC/Al composites mixed with diamond

The thermophysical properties of the SiC /Al composites mixed with diamond（SiC-Dia/Al） were studied through theoretical calculation and experiments. The thermal conductivity and the thermal expansion coefficient of the SiC-Dia/Al were calculated by differential effective medium（DEM） theoretical model and extended Turner model, respectively. The microstructure of the SiC-Dia/Al shows that the combination between SiC particles and Al is close, while that between diamond particles and Al is not close. The experimental results of the thermophysical properties of the SiC-Dia/Al are consistent with the calculated ones. The calculation results show that when the volume ratio of the diamond particles to the SiC particles is 3：7, the thermal conductivity and the thermal expansion coefficient can be improved by 39% and 30% compared to SiC/Al composites, respectively. In other words, by adding a small amount of diamond particles, the thermophysical properties of the composites can be improved effectively, while the cost increases little.

Mixed rare earth metal conversion coatings on 2024 alloy and Al6061/SiC_p metal matrix composites

The processes of mixed rare earth metal (REM) conversion coatings on 2024 alloy and Al6061/SiC p metal matrix composites (MMC) were introduced. The coatings were examined to be honeycomb like feature by scanning electron microscope. X ray diffraction analysis revealed that the coatings are amorphous structure. The results of X ray photoelectron spectroscopy indicated that the mixed REM conversion coatings consist predominantly of Ce and O, the contents of other rare earth elements (such as La, Pr) are relatively low, the coatings are about 2～4 μm thickness with excellent adhesion and wearability. The results of mass loss test showed that the mixed REM conversion coatings produce corrosion resistant surface of 2024 alloy and Al6061/SiC p. [

Microstructure and properties of Al/Si/SiC composites for electronic packaging

The Al/Si/SiC composites with medium volume fraction for electronic packaging were fabricated by gas pressure infiltration.On the premise of keeping the machinability of the composites,the silicon carbide particles,which have the similar size with silicon particles（average 13 μm）,were added to replace silicon particles of same volume fraction,and microstructure and properties of the composites were investigated.The results show that reinforcing particles are distributed uniformly and no apparent pores are observed in the composites.It is also observed that higher thermal conductivity（TC） and flexural strength will be obtained with the addition of SiC particles.Meanwhile,coefficient of thermal expansion（CTE） changes smaller than TC.Models for predicting thermal properties were also discussed.Equivalent effective conductivity（EEC） was proposed to make H-J model suitable for hybrid particles and multimodal particle size distribution.

FATIGUE BEHAVIOUR OF SiC_p/6061Al COMPOSITE

The fatigue of SiC_p/6061Al composite containing 15 v.-% SiC particles has been compared with 6061Al alloy.Dislocation structure and microprocess of fatigue crack initiation and propagation in the composite have been investigated by using SEM and TEM.The results in- dicate that the fatigue strength at 10~7 cycles of the composite is 196 MPa,i.e.about 25% higher than matrix alloy.The voids and microcracks initiated at and near the interface be- tween SiC_p and matrix,where has a higher density of dislocations,will propagate and link up to form the fatigue crack.It is an important evidence to note that the dislocation channels where screw dislocation can travel are formed near interface and corner region of SiC_o in the composite subjected to fatigue stress(σ_(max)=274 MPa N=2.4×10~5 cycles),demonstrating the relationship between fatigue crack initiation and dislocation movement in the SiC particles reinforced 6061 Al alloy composite.

Mechanical and Machining Properties Analysis of Al6061-Cu-Reinforced SiC_PMetal Matrix Composite

The metal matrix composite (MMC), despite of its high stiffness, strength, corrosion resistance, wear resistance, non-react with chemicals and so many other tailored qualities which are never obtained in alloy of metals, has limited utilization due to the high cost of fabrication. In this study, a modest attempt has been made to find out the process parameters at which best mechanical properties of Al6061, 4% Cu and reinforced 5% SiCP ceramic MMC can be obtained. The addition of 4% Cu in Al6061 is more or less comparable to the composition duralumin, which are widely used in aerospace applications. SiCP is hard and has linear thermal expansion at high temperature. With reinforcement of SiCP in Al6061-Cu alloy, it can be postulated that hardness of MMC retains at high temperature applications. An analysis of Variance (ANOVA) and linear regression was used for analysis of data with the help of SPSS (Version-17.0). Independent parameters are five levels of pouring rates (1.5 cm/s, 2.0 cm/s, 2.5 cm/s, 3.0 cm/s and 3.5 cm/s), and material type (Al6061 + 4% Cu alloy and Al6061 + 4% Cu, reinforced 5% SiCp MMC processed using stir casting technique) and dependent parameters are hardness and impact strength material removal rates of workpiece. It is found that at different pouring rates material hardness and impact strength of workpiece are highly significant but the material removal rate of workpiece is having no significance value. At pouring rate of 2.5 cm/s and 700℃ ± 5℃ pouring temperature, optimum values of hardness and impact strength are observed as compared to other values of pouring rates (1.5 cm/s, 2.0 cm/s, 3.0 cm/s and 3.5 cm/s). Material Removal rate for work pieces of Al6061 + 4% Cu alloy is less as compared to MMC. So it can be concluded that MMC has better machining ability compared to Al6061 + 4% Cu alloy. Material removal rate of Al6061 + 4% Cu, reinforced 5% SiCP MMC has maximum values at 1.5 cm/s pouring rate compared to 2.0 cm/s, 2.5 cm/s, 3.0 cm/s and 3.5 cm/s pouring rates. With reinforcement of 5% SiC trend of mechanical properties is same, but the hardness and impact strength of MMCs are increased by 25% and 20% respectively. Also it is observed from scanning electron microscopy (SEM) that at pouring rate 2.5 cm/s a better homogeneity can be obtained.

Experimental study and numerical analysis on dry friction and wear performance of co-continuous SiC/Fe-40Cr against SiC/2618 Al alloy composites

The dry friction and wear behaviors of co-continuous composites SiC/Fe–40Cr against SiC/Al 2618 alloy were investigated on a ring-on-ring friction and wear tester at sliding speed of 30-105 m/s under the load of 1.0-2.5 MPa. The experimental result reveals that the characteristic of two body abrasive wear and oxidation wear mechanisms are present for SiCn/2618 Al composite under higher load and sliding speed. SiC ceramic continuous network as the reinforcement can avoid composite from the third body wear that usually occurs in traditional particle reinforced composite. The mechanically mixed layer (MML) controls greatly the wear rate and friction coefficient of the composites. The composites tested at higher sliding speed exhibit higher value of friction coefficient and fluctuation, which is associated with the intermittent formation and removal of the MML. The wear and stress—strain behaviors of SiCn/Fe–40Cr against SiCn/Al 2168 at 30-105 m/s under 1.0-2.5 MPa were analyzed by finite element method with the software Solidwork2012 Simulation, respectively. The wear and stress–strain behavior of the composite predicted by the FEM correlated well with the experimental results.

Flow stress behavior and processing map of extruded 7075Al/SiC particle reinforced composite prepared by spray deposition during hot compression

Hot compression tests of the extruded 7075Al/15%SiC (volume fraction) particle reinforced composite prepared by spray deposition were performed on Gleeble?1500 system in the temperature range of 300?450 °C and strain rate range of 0.001?1 s?1. The results indicate that the true stress?true strain curve almost exhibits rapid flow softening phenomenon without an obvious work hardening, and the stress decreases with increasing temperature and decreasing strain rate. Moreover, the stress levels are higher at temperature below 400 °C but lower at 450 °C compared with the spray deposited 7075Al alloy. Superplastic deformation characteristics are found at temperature of 450 °C and strain rate range of 0.001?0.1 s?1 with corresponding strain rate sensitivity of 0.72. The optimum parameters of hot working are determined to be temperature of 430?450 °C and strain rate of 0.001?0.05 s?1 based on processing map and optical microstructural observation.

Microstructures and mechanical properties of 2024Al/Gr/SiC hybrid composites fabricated by vacuum hot pressing

The 2024Al/Gr/SiC hybrid composite plates with 5%-10% SiC particles （volume fraction） and 3%-6% flaky graphite （Gr） （volume fraction） were fabricated by vacuum hot pressing and hot extrusion processing. The effects of SiC and Gr on the microstructures and mechanical properties of the composites aged at 160, 175 and 190℃ were studied by optical microscopy, scanning electron microscopy （SEM）, and hardness and tensile tests. The results indicate that the SiC particles have a more obvious effect on accelerating the aging response as compared with the Gr. Both the tensile strength and elongation are reduced by the Gr and SiC particles added into the matrix, while the Gr has a more negative influence on the elongation than the SiC particles. The tensile strength （ab）, yield stress （as） and elongation （δ） of the 2024Al/3Gr/10SiC composite aged at 165℃ for 8 h are 387 MPa, 280.3 MPa and 5.7%, respectively. The hybrid composites are characterized by ductile fracture, which is associated with the ductile fracture of the matrix and the tearing of the interface between the matrix and the particles.

Microstructural and abrasive wear properties of SiC reinforced aluminum-based composite produced by compocasting

The effect of SiC particles reinforcement with average size of 1, 5, 20 and 50 μm and volume fraction of 5%, 10% and 15% on the microstructure and tribological properties of Al-based composite was investigated. Composites were produced by applying compocasting process. Tribological properties of the unreinforced alloy and composites were studied using pin-on-disc wear tester, under dry sliding conditions at different specific loads. The influence of secondary mechanical processing with different rolling reductions on the dry sliding wear characteristics of Al matrix composites was also assessed. Hardness measurement and scanning electron microscopy were used for microstructural characterization and investigation of worn surfaces and wear debris. The proper selection of process parameter such as pouring temperature, stirring speed, stirring time, pre-heated temperature of reinforcement can all influence the quality of the fabricated composites. The porosity level of composite should be minimized and the chemical reaction between the reinforcement and matrix should be avoided.

Particle Removal Mechanism of High Volume Fraction SiCp/Al Composites by Single Diamond Grit Tool

Particle removal mechanism was presented during machining particle SiC/Al composites with diamond grinding tool. The relevant removal modes and their mechanisms were discussed considering the impact and squeezing effect of diamond grit on the SiC particle. The experimental results show that the aluminum matrix has larger plastic deformation, so the aluminum mixed with the surplus SiC particles is cut from the surface. The SiC particles can be removed in multiple ways, such as broken/fractured, micro cracks, shearing and pulled out, etc. More particles removed by shearing, and less particles removed by fractured during material removal progress can produce a better machined surface.

Microstructure and mechanical properties of SiC-particle-strengthening tri-metal Al/Cu/Ni composite produced by accumulative roll bonding process

In this study, a multilayer Al/Ni/Cu composite reinforced with Si C particles was produced using an accumulative roll bonding(ARB) process with different cycles. The microstructure and mechanical properties of this composite were investigated using optical and scanning microscopy and hardness and tensile testing. The results show that by increasing the applied strain, the Al/Ni/Cu multilayer composite converted from layer features to near a particle-strengthening characteristic. After the fifth ARB cycle, a composite with a uniform distribution of reinforcements(Cu, Ni, and SiC) was fabricated. The tensile strength of the composite increased from the initial sandwich structure to the first ARB cycle and then decreased from the first to the third ARB cycle. Upon reaching five ARB cycles, the tensile strength of the composite increased again. The variation in the elongation of the composite exhibited a tendency similar to that of its tensile strength. It is observed that with increasing strain, the microhardness values of the Al, Cu, and Ni layers increased, and that the dominant fracture mechanisms of Al and Cu were dimple formation and ductile fracture. In contrast, brittle fracture in specific plains was the main characteristic of Ni fractures.