Wear behavior of SiC/PyC composite materials prepared by electromagnetic-field-assisted CVI

Silicon carbide/pyrolytic carbon (SiC/PyC) composite materials with excellent performance of self-lubrication and wear resistance were prepared on SiC substrates by electromagnetic-field-assisted chemical vapor infiltration (CVI). The composition and microstructure of the SiC/PyC materials were investigated in detail by XRD, SEM and EDS, etc. The effects of the deposition temperature on the section features and wear resistance of the SiC/PyC were studied. The results show that the PyC layers were deposited onto SiC substrates spontaneously at a lower deposition temperature. The SiC substrates deposited with PyC can significantly reduce the wear rate of the self-dual composite materials under dry sliding condition. The wear tests suggest that the SiC/PyC composite materials own a better wear resistance property when the deposition temperature is 800 °C, and the wear rate is about 64.6% of that without the deposition of PyC.

SYNTHESIS OF SiC WHISKER AND ITS APPLICATION IN COMPOSITE MATERIALS

The SiC whiskers (SiCw) synthesized from rice hulls is studied in this paper. The properties of the application in the composite materials are tested, and also compared with the SiCw produced in US and Japan, the results indicate that the SiCw produced by this method is mainly straight crystals with multi nodes on face, the main type is P-SiC. lt has many advantages such as high strength and excellent oxidation resistance to high temperature. The Si3N4 ceramic composite materials reinforced and toughened with the SiCw, δfRT of the material is (856±22)MPa, δf300℃ is approximately (418. 5±14. 2) MPa and Klc is approximately (11. 3±1. 0) MPa m1/2. Besides, the application of the SiCw in the engineering materials of mining is forecasted.

Synthesis of steel slag ceramics: chemical composition and crystalline phases of raw materials

Two types of porcelain tiles with steel slag as the main raw material （steel slag ceramics） were synthesized based on the CaO-A1203-SiO2 and CaO--MgO-SiO2 systems, and their bending strengths up to 53.47 MPa and 99.84 MPa, respectively, were obtained. The presence of anorthite, a-quartz, magnetite, and pyroxene crystals （augite and diopside） in the steel slag ceramics were very different from the composition of traditional ceramics. X-ray diffraction （XRD） and electron probe X-ray microanalysis （EPMA） results illustrated that the addition of steel slag reduced the temperature of extensive liquid generation and further decreased the firing temperature. The considerable contents of glass-modifying oxide liquids with rather low viscosities at high temperature in the steel slag ceramic adobes promoted element diffusion and crystallization. The results of this study demonstrated a new approach for extensive and effective recycling of steel slag.

High strength bimetallic composite material fabricated by electroslag casting and characteristics of its composite interface

Bimetallic composite material of bainitic steel and PD3 steel was produced with electroslag casting process, and element distribution of its composite interface was investigated by theoretical calculation and energy dispersive spectrometer(EDS). Results show that the tensile strength(1,450 MPa), hardness(HRC 41-47) and impact toughness(94.7J·cm^(-2)) of bainitic steel were comparatively high, while its elongation was slightly low(4.0%). Tensile strength(1,100 MPa), hardness(>HRC 31) and elongation(7.72%) of the interface were also relatively high, but its impact toughness was low at 20.4 J·cm^(-2). Results of theoretical calculation of the element distribution in the interface region were basically consistent with that of EDS. Therefore, electroslag casting is a practical process to produce bimetallic composite material of bainitic steel and PD3 steel, and theoretical calculation also is a feasible method to study element distribution of their interface.

Thermodynamic analysis and formula optimization of steel slag-based ceramic materials by FACTsage software

Using steel slag as a main raw material of ceramics is considered as a high value-added way. However, the relationship among the initial composition, ceramic microstructure, and macroscopic properties requires further study. In this paper, a series of ceramics with different slag ratios （0-70wt%） were designed, and the software FACTsage was introduced to simulate the formation of crystalline phases. The simulation results indicate that mullite is generated but drastically reduced at the slag ratios of 0-25wt%, and anorthite is the dominant crystalline phase in the slag content of 25wt%-45wt%. When the slag ratio is above 45wt%, pyroxene is generated more than anorthite. This is because increasing magnesium can promote the formation of pyroxene. Then, the formula with a slag content of 40wt% was selected and optimized. X-ray diffraction results were good consistent with the simulation results. Finally, the water absorption and bending strength of optimized samples were measured.

Evolution of microstructure and mechanical properties in multi-layer 316L-TiC composite fabricated by selective laser melting additive manufacturing

In this study,the microstructure and mechanical properties of a multi-layered 316L-TiC composite material produced by selective laser melting(SLM)additive manufacturing process are investigated.Three different layers,consisting of 316L stainless steel,316L-5 wt%TiC and 316L-10 wt%TiC,were additively manufactured.The microstructure of these layers was characterized by optical microscopy(OM)and scanning electron microscopy(SEM).X-ray diffraction(XRD)was used for phase analysis,and the mechanical properties were evaluated by tensile and nanoindentation tests.The microstructural observations show epitaxial grain growth within the composite layers,with the elongated grains growing predominantly in the build direction.XRD analysis confirms the successful incorporation of the TiC particles into the 316L matrix,with no unwanted phases present.Nanoindentation results indicate a significant increase in the hardness and modulus of elasticity of the composite layers compared to pure 316L stainless steel,suggesting improved mechanical properties.Tensile tests show remarkable strength values for the 316L-TiC composite samples,which can be attributed to the embedded TiC particles.These results highlight the potential of SLM in the production of multi-layer metal-ceramic composites for applications that require high strength and ductility of metallic components in addition to the exceptional hardness of the ceramic particles.

Microstructural characterization and mechanical properties of functionally graded Al2024/SiC composites prepared by powder metallurgy techniques

Al2024/SiC functionally graded materials (FGMs) with different numbers of graded layers and different amounts of SiC were fabricated successfully by powder metallurgy method and hot pressing process. The effects of increasing SiC content and number of layers of Al2024/SiC FGMs on the microstructure and mechanical properties of the composite were investigated. X-ray diffraction (XRD) and scanning electron microscopy (SEM) with energy-dispersive X-ray spectroscopy (EDX) analyses indicated that Al and SiC were dominant components as well as others such as Al4C3, CuAl2, and CuMgAl2

INFLUENCES OF VACUUM-BAKING TREATMENT TO SiC PARTICULATES ON PREPARING AI-MATRIX COMPOSITE

A study was made of influences of vacuum-baking treatment to SiC particulates on preparing cast Al-martix composite. By means of quadripole mass analyser(QMA), gases absorbed on the surface of SiC particulate have been investigated, it is found that gases and pollutants absorbed on the surface prohibit SiC particulates from uniformly dispersing in the alloy melt.

Mechanical Properties and Microstructure of Al_(2)O_(3)/SiC Composite Ceramics for Solar Heat Absorber

Al_(2)O_(3)/SiC composite ceramics were prepared fromα-Al_(2)O_(3) and SiC by a pressureless sinter method in this study.The effect of SiC contents on the mechanic properties,phase compositions and microstructure is studied.Experimental results show that the vickers hardness,wear resistance and thermal conductivity of the samples increase with the increase in the SiC content,and the hardness of the sample reaches 16.22 GPa,and thermal conductivity of the sample reaches 25.41 W/(m.K)at room temperature when the SiC content is 20 wt%(B5)and the sintering temperature is at 1640℃.Higher hardness means higher scour resistance,and it indicates that the B5 material is expected to be used for the solar heat absorber of third generation solar thermal generation.The results indicate the mechanism of improving mechanical properties of Al_(2)O_(3)/SiC composite ceramics:SiC plays a role in grain refinement that the grain of SiC inhibits the grain growth of Al_(2)O_(3),while the addition of SiC changes the fracture mode from the intergranular to the intergranular-transgranular.

Ballistic Performance and Damage Characteristics of Chemical Vapor Infiltration Quasi 3D-Cf/SiC Composites

To investigate the ballistic performance and damage characteristics of quasi threedimensional（3D） needle-punched Cf/SiC composites prepared by chemical vapor infiltration（CVI）,penetration experiments were conducted by using 7.62 mm armor piercing incendiary（API）.Macro and micro fracture morphologies were then observed on recycled targets.The results show that the protection coefficient of 3D Cf/SiC composites is 2.54.High porosity and many micro thermal stress cracks may directly lead to the lower ballistic performance.Flat fracture morphology was observed on the crater surface.The low dynamic fracture strength along layer direction may be attributed to the voids and microcracks caused by residual thermal stress.The damage characteristics of Cf/Si C composites include matrix cracking,fiber bundle cracking,interfacial debonding,fiber fracture,and fiber bundle pull-out.And interfacial debonding and fiber fracture may play major roles in energy absorption.

SiC whisker reinforced MoSi_2 composite prepared by spark plasma sintering from COSHS-ed powder

SiC whisker reinforced MoSi2 composite powder was synthesized by a novel process, referred to the literature as chemical oven self-propagating high temperature synthesis(COSHS). The as-prepared SiCw/MoSi2 composite powder was rapidly sintered by spark plasma sintering(SPS) process. The sintering temperature and pressure were 1 723 K at heating rate of 100 K/min and 40 MPa, respectively. The microstructure and mechanical properties of the composite were investigated. Relative densities of the monolithic material and composite are 95% and 99.3%, respectively. SEM micrographs of SiCw/MoSi2 composite show that SiC whiskers homogeneously distribute in MoSi2 matrix. The composite containing SiC whisker has higher Vicker hardness than monolithic MoSi2. Especially the room-temperature fracture toughness of the composite is higher than that of MoSi2, from 3.6 MPa·m1/2 for MoSi2 to 7.7 MPa·m1/2 for composite with 15% SiC(volume fraction), increased by 113.9%. The morphology of propagation of crack and fractured surface of composite reveal the mechnaism to improve fracture toughness of MoSi2 matrix. The results show that the in-situ SiCw/MoSi2 composite powder prepared by COSHS technique can be successfully sinterded through SPS process and significant improvement of low temperature fracture toughness can be achieved.

Influence of Tungsten and Cobalt Contents on the Microstructure Changes and Fracture Behavior of New Carbon-Free Steel-alloy Composites

The ever increasing demand for steel materials that have good combinations between strength and toughness urged all researchers working in the field of material science to find new alloys that can approach that requirement.Unfortunately strength and toughness of materials are always counter acting properties.However,carbon contents in the steel define to a great extent its strength and toughness.In this research an effort is paid to produce steel alloy composites that can give higher strength together with good toughness without alloying with carbon.The mechanism of strengthening in Iron-Cobalt-Tungsten composite alloys with variations in Co and W contents is investigated.The fracture toughness and hardness,are measured for all alloy composites under investigation.The changes in microstructures after heat treatment are emphasized using metallurgical microscopy and SEM-aided with EDX analyzing unit.

Microstructure and properties of composite of stainless steel and partially stabilized zirconia

To fabricate the metal-ceramics multi-layer hollow functionally gradient materials(FGMs) that might meet the requirement of repeated service and long working time of high temperature burners, such as spacecraft engine, the microstructure and properties of composite of stainless steel and partially stabilized zirconia were investigated. Samples of different proportions of stainless steel to partially yttria-stabilized zirconia were fabricated by powder extrusion and sintering method. Shrinkage, relative density, microstructure, micro-Vickers hardness, compression strength, bending strength, fractography morphology and electrical resistivity of sintered samples with different proportions of stainless steel were measured. The results show that threshold of metallic matrix composite(MMC) is approximately equal to 60%(volume fraction) stainless steel. The samples with 0 to 50%(volume fraction) stainless steel indicate ceramic brittleness and non-cutability, and the samples with 70% to 100%(volume fraction) stainless steel indicate metallic plasticity and cutability.

Ablation Performance of a Novel Super-hybrid Composite

A novel super-hybrid composite (NSHC) was boron-modified phenolic resin (BPR) with three-dimensional reticulated SiC ceramic (3DRC) and high silica fibers. Ablation performance of the NSHC was studied. The results show that the linear ablation rate of NSHC was lower than that of pure BPR and the high silica/BPR composite. Its linear ablation rate is 1/17 of the high silica/BPR. Mass ablation rate of the NSHC is very close to that of the pure BPR and the high silica/BPR composite. Scanning electron microscope (SEM) analysis indicates that 3DRC has scarcely changed its shape at the ablation temperature. Its special reticulated structure can restrict the materials deformation and prevent high velocity heat flow from eroding the surface of the materials largely and thus increase ablation resistance of the NSHC.

RESEARCH ON THE HIGH PERFORMANCE COMPOSITE ROAD CONCRETE

Ordinary concrete presents short service life when used for building and repairing high-grade road with heavy traffic due to its large brittleness, poor bending flexibility and serious shrinkage on drying. In this paper, a new kind of high performance concrete has been designed by means of combination of organic, inorganic material as well as metal material. The research and application have shown that this new concrete can significantly counteract the deficiency of ordinary concrete and give excellent mechanical properties and pavement performances. The application of this new kind of concrete is of great social and economic significance.

C/SiC复合材料数据库及机器学习性能预测平台的设计与开发

以MySQL Workbench 8.0为数据库平台,采用三层浏览器/服务器架构,利用PyCharm 2022开发了一套基于Web界面和机器学习技术的C/SiC复合材料数据库系统,该系统包括材料数据库和机器学习模型2部分,具有对材料组分结构、制备工艺、试验性能等材料研发各阶段的信息查询、添加、修改、删除、搜索以及支持信息管理、设计分析视图、案例推理辅助设计、用户与系统管理等功能。基于神经网络回归算法训练机器学习模型,利用材料微观结构参数预测材料力学性能,对不同微观结构参数的影响权重进行评价,并部署在系统平台中;通过Web用户界面调用机器学习模型,对预留的验证集数据进行拉伸模量和弯曲模量预测。结果表明:机器学习模型预测材料力学性能的精度达到95%左右,训练出来的预测模型具有良好的精度与泛化能力。

SUPER-THIN COATING MATERIAL FOR HIGH-GRADE HIGHWAY

The road surface of cement concrete in highway is easily cracked and even destroyed due to inhomogeneous subsiding of the road foundation. In this work, a super-thin-coating material is prepared in order to repair the destroyed thin road surface, in which polymers and steel-fiber are added into ordinary concrete to form a steel fiber reinforced polymer-cement-based composite, the composite was successfully used to repair road surface. Microstructure and mechanical properties of the composites are measured and analyzed.

Ablation Property of Ceramics/Carbon Fibers/Resin Novel Super-hybrid Composite

A novel super-hybrid composite (NSHC) is prepared with three-dimension reticulated SiC ceramic (3DRC), high performance carbon fibers and modified phenolic resin (BPR) in this paper. Ablation performance of super-hybrid composite is studied. The results show that the NSHC has less linear ablation rate compared with pure BPR and CF/BPR composite, for example, its linear ablation rate is 50% of CF/BPR at the same fiber content. Mass ablation rate of the NSHC is slightly lower than that of pure BPR and CF/BPR composite because of their difference in the density. Scanning electron microscopic analysis indicates that 3DRC can increase anti-erosion capacity of materials because its special reticulated structure can control the deformation of materials and strengthen the stability of integral structure.

Development of non-shrinkable ceramic composites for use in high-power microwave tubes

Al_2O_3–CaO–SiC-based ceramic composites with four different compositions were sintered at 1700℃ for 3 h in an air furnace. The phase analysis, microstructural characterization, and elemental composition determination of the developed composites were performed by X-ray diffraction(XRD), field-emission scanning electron microscopy(FESEM), and energy-dispersive X-ray(EDAX) analysis, respectively. The shrinkage, thermal properties, and electrical resistivity of the composites were also studied. The experimental results showed the effects of adding silicon carbide and calcia to alumina on the thermal, electrical, and shrinkage properties of the resultant composites. Among the four investigated ceramic composites, the one composed of 99 wt% alumina, 0.5 wt% CaO, and 0.5 wt% SiC exhibited the best characteristics for use as a potting material in a dispenser cathode of a microwave tube. The material exhibited slight expansion instead of shrinkage during drying or firing. Other properties of the composite powder, such as its thermal properties and electrical resistivity, were comparable to those of a commercial alumina powder.