Wear Behaviour of Al-SiCp Metal Matrix Composites and Optimization Using Taguchi Method and Grey Relational Analysis

Aluminium metal matrix composite is a relatively new material that has proved its position in automobile, aerospace and other engineering design applications due to its wear resistance and substantial hardness. Need for improved tribological performance has led to the design and selection of newer variants of the composite. The present investigation deals with the study of wear behaviour of Al-SiCp metal matrix composite for varying reinforcement content, applied load, sliding speed and time. Aluminium metal matrix composites reinforced with SiC particles are prepared by liquid metallurgy route using LM6 aluminium alloy and silicon carbide particles (size ~ 37 μm) by varying the weight fraction of SiC in the range of 5% - 10%. The material is synthesized by stir casting process in an electric melting furnace. The materials are then subjected to wear testing in a multitribotester using block on roller configuration. A plan of experiments based on L27 Taguchi orthogonal array is used to acquire the wear data in a controlled way. An analysis of variance is employed to investigate the influence of four controlling parameters, viz., SiC content, normal load, sliding speed and sliding time on dry sliding wear of the composites. It is observed that SiC content, sliding speed and normal load significantly affect the dry sliding wear. The optimal combination of the four controlling parameters is also obtained for minimum wear. The microstructure study of worn surfaces indicates nature of wear to be mostly abrasive.

SiCp/Al-Si基复合材料界面结构调控及强化机制的研究进展

SiCp/Al-Si基复合材料具有高的比强度、比刚度、比模量,良好的导热、导电、耐磨性及尺寸稳定性等优点,作为结构功能性材料应用于空间工程、电子封装、交通运输和精密仪器等领域。其研究热点主要集中在界面结构调控、强化机制及性能调控等方面。在SiCp/Al-Si复合材料中存在着增强体与基体界面、析出相与基体界面、析出相与增强体界面,这些界面受各种因素影响,会出现多种界面反应和界面产物,界面结构和结合状态复杂而多样。基于此,本文综述了制备工艺、基体合金成分和SiCp表面改性等方面对SiCp/Al-Si基复合材料界面结构的影响及调控,并总结了影响其力学性能的因素及强化机制的研究现状,最后对复合材料未来的发展及研究方向进行了展望。

Particle Removal Mechanism of High Volume Fraction SiCp/Al Composites by Single Diamond Grit Tool

Particle removal mechanism was presented during machining particle SiC/Al composites with diamond grinding tool. The relevant removal modes and their mechanisms were discussed considering the impact and squeezing effect of diamond grit on the SiC particle. The experimental results show that the aluminum matrix has larger plastic deformation, so the aluminum mixed with the surplus SiC particles is cut from the surface. The SiC particles can be removed in multiple ways, such as broken/fractured, micro cracks, shearing and pulled out, etc. More particles removed by shearing, and less particles removed by fractured during material removal progress can produce a better machined surface.

Optimization of Machining Characteristics for Al/SiCp Composites using ANN/GA

The present work is focused on optimization of machining characteristics of AI/SiCp composites. The machining characteristics such as specific energy, tool wear and surface roughness were studied. The parameters such as volume fraction of SiC, cutting speed and feed rate were considered. Artificial neural networks (ANN) was used to train and simulate the experimental data. Genetic algorithms (GA) was interfaced with ANN to optimize the machining conditions for the desired machining characteristics. Validation of optimized results was also performed by confirmation experiments.

Effect of mixed rare earth oxides and CaCO_3 modification on the microstructure of an in-situ Mg_2Si/Al-Si composite

The effects of mixed rare earth oxides and CaCO3 on the microstructure of an in-situ Mg2Si/Al-Si hypereutectic alloy composite were investigated by optical microscope,scanning electron microscope,and energy dispersive spectrum analysis. The results showed that the morphol-ogy of the primary Mg2Si phase particles changed from irregular or crosses to polygonal shape,their sizes decreased from 75 μm to about 25 μm,and the compound of both the oxide and CaCO3 was better than either the single mixed rare earth o...

Near-net shaped Al/SiCP composites via vacuum-pressure infiltration combined with gelcasting

To solve the problem of difficult machining, the near-net shaped Al/SiCP composites with high volume fraction of SiC particles were fabricated by vacuum-pressure infiltration. The SiCP preform with a complex shape was prepared by gelcasting. Pure Al, Al4Mg, and Al4Mg2Si were used as the matrices, respectively. The results indicate that the optimal parameters of SiCP suspension in gelcasting process are pH value of 10, TMAH content of 0.5 wt.%, and solid loading of 52 vol.%. The Al matrix alloyed with Mg contributes to improving the interfacial wettability of the matrix and SiC particles, which increases the relative density of the composite. The Al matrix alloyed with Si is beneficial to inhibiting the formation of the detrimental Al4C3 phases. The Al4Mg2Si/SiCP composite exhibits high relative density of 99.2%, good thermal conductivity of 150 W·m^-1·K^-1, low coefficient of thermal expansion of 10.1×10^-6 K^-1, and excellent bending strength of 489 MPa.

Preparation and characterization of different surface modified SiCp reinforced Al-matrix composites

The effects of SiCp surface modifications(Cu coating,Ni coating and Ni/Cu coating)on the microstructures and mechanical properties of Al matrix composites were investigated.Surface modification of SiC particles with Cu,Ni and Cu/Ni,respectively,was carried out by electroless plating method.SiCp/Al composites were prepared by hot pressed sintering followed by hot extrusion.The results show that the surface modification of SiC particles plays an effective role,which is relative to the type of surface coating,and the interfacial bonding become stronger in the following order:untreated SiCp<Ni(Cu)-coated SiCp<Ni/Cu-coated SiCp.The Ni/Cu-coated SiCp/Al composites exhibit the best comprehensive mechanical properties,with ultimate tensile strength(σUTS)and fracture strain(εf)of 389 MPa and 6.3%,respectively.Compared with that of untreated-SiCp/Al composites,theσUTS andεf are enhanced by 19.3%and 57.5%.

Microstructure evolution of rare earth Pr modified alumina-silicate short fiber-reinforced Al-Si metal matrix composites

Al-Si metal matrix composites (MMCs) reinforced with 20 vol.% alumina-silicate shot fibers (Al2O3-SiO2(sf)) were fabricated by an infiltration squeeze method. Pure Pr metal was added into these composites. The effect of Pr addition on the microstructure evolution of Al-Si MMCs was investigated by SEM,TEM,and EDS. Pr addition is favorable to make uniform microstructures with the modified eutectic Si crystal. PrAlSi phase with high contents of Pr and Si is observed on the interface between the fiber and the m...

Effect of a Slight Interfacial Reaction on Mechanical Properties of SiCp/Al Composites

A slight interfacial reaction in squeeze-cast SiCp/6061AI composites has been studied. It is found that this kind of reaction has a particular effect on the mechanical properties of the composites. The results of fie-cure tests show that this reaction in the composites obviously increases the elastic properties, but is not beneficial to the fracture strength and ductility.This phenomenon can be interpreted in terms of two different micromechanisms which have been analyzed using TEM and HREM observations, acoustic emission (AE) technique and SEM fractography. In addition, a new method of SiC surface modification which can control the interface state is initially presented.

Wear mechanism for spray deposited Al-Si/SiC_p composites under dry sliding condition

Al-Si/15%SiCp(volume fraction) composites with different silicon contents were fabricated by spray deposition technique, and typical microstructures of these composites were studied by optical microscopy(OM). Dry sliding wear tests were carried out using a block-on-ring wear machine to investigate the effect of applied load range of 10-220 N on the wear and friction behavior of these composites sliding against SAE 52100 grade bearing steel. Scanning electron microscopy(SEM) and energy-dispersive X-ray microanalysis(EDAX) were utilized to examine the morphologies of the worn surfaces in order to observe the wear characteristics and investigate the wear mechanism. The results show that the wear behavior of these composites is dependent on the silicon content in the matrix alloy and the applied load. Al-Si/15%SiCp composites with higher silicon content exhibit better wear resistance in the applied load range. Under lower loads, the major wear mechanisms are oxidation wear and abrasive wear for all tested composites. Under higher loads, severe adhesive wear becomes the main wear mechanisms for Al-7Si/15%SiCp and Al-13Si/15%SiCp composites, while Al-20Si/15%SiCp presents a compound wear mechanism, consisting of oxidation, abrasive wear and adhesion wear.

Effect of Sb on microstructure and mechanical properties of Mg_2Si/Al-Si composites

The effect of Sb on the microstructure and mechanical properties of Mg2Si/Al-Si composites was investigated.The results show that Sb can improve the microstructure and mechanical properties of Mg2Si/Al-Si composites.When the content of Sb is 0.4%,the morphology of primary Mg2Si changes from dendrites to fine particles,the average size of Mg2Si particles is refined from 52 to 25μm,and the ultimate tensile strength and elongation of the composites increase from 102.1 MPa and 0.26% to 138.6 MPa and 0.36%,respectively.The strengthening mechanism can be attributed to the fine-grain strengthening.However,excessive Sb is disadvantageous to the modification of the composites.

AN IN SITU SURFACE COMPOSITE AND GRADIENT MATERIAL OF Al-Si ALLOY PRODUCED BY ELECTROMAGNETIC FORCE

Because of the different conductivities between the primary phase (low electric conduc tivity) and the metal melt, electromagnetic force scarcely acts on the primary phase. Thus, an electromagnetic repulsive force applied by the metal melt exerts on the pri mary phase when the movement of the melt in the direction of electromagnetic force is limited. As a result, the repulsive force exerts on the primary phase to push them to move in the direction opposite to that of the electromagnetic force when the metal melt with primary phase solidifies under an electromagnetic force field. Based on this, a new method for production of in situ surface composite and gradient material by electromagnetic force is proposed. An in situ primary Si reinforced surface composite of Al-15wt%Si alloy and gradient material of Al-l9wt%Si alloy were produced by this method. The microhardness of the primary Si is HV1320. The reinforced phase size is in the range from 40μm to 100μm. The wear resistance of Al-Si alloy gradient material can be more greatly increased than that of their matrix material.

Effect of Na3AlF6 Addition and Surface Modification of SiCp on the Microstructure and Mechanical Properties of SiCp/Al Composites

Al-matrix composites reinforced with 56.5 vol% SiC were prepared by powder metallurgy with different amounts of additives and surface modifications of SiCp. The crystalline phase, morphology, elements on the surface of SiCp and the interface between SiCp and Al were characterized by XRD, SEM, EDS and EPMA. The results show that it is favorable for the reaction between TiO2-C on the surface of SiCp and Al at the SiCp-Al interface at 1 050 ℃. Besides, the process of Na3 AlF6 melting, dissolving and then contacting with Al2 O3 formed the NaF-AlF3-Al2 O3 system, which generated OAlF2-, promoting the dessolution of Al2 O3 film on the surface of Al powder. Na3 AlF6 meets the needs of chemical reaction in TiO2-C-Al system at the SiCpAl interface in the way of offering more molten Al. After 0.75 wt% Na3 AlF6 was added into raw materials, the whole TiO2-C film and most SiO2 film were destroyed and the interfacial bonding between SiCp and Al was keeping good, in which no obvious void and crack were observed. Meanwhile, no brittle Al4 C3 phase formed in the system. At this time, the flexure strength and density of samples presented optimal values, reaching up to 106.5 MPa and 90.77% respectively.

Study on fracture behavior of SiCp/A356 composites

The fracture behavior of SiCp/A356 composite at room and high temperatures was studied. Under tensile stress condition at room temperature, the fracture is mostly a combination of the brittle fracture of SiC particles and ductile fracture of A356 matrix. As the tensile temperature increases, the composite changes the main fracture behavior to the separation fracture of the bonding surface between SiC particles and A356 matrix. When the tensile temperature reaches 573 K, the fracture behavior of the composites is almost the whole separation fracture of the bonding surface, which is the main strengthening mechanism at high temperature. Under the cycle stress condition at room and high temperatures, the main fracture behavior of the composites is always a combination of the brittle fracture of SiC particles and ductile fracture of A356 matrix. However, under the cycle stress at high temperature, cycle behavior of the composites changes from cycle hardening at room temperature to the cycle softening at high temperature.

Experimental Study of Machinability in Millgrinding of SiCp/Al Composites

An attempt was made to investigate the machinability of Si Cp/Al composites based on the experimental study using mill-grinding processing method. The experiments were carried out on a high-speed CNC machining center using integrated abrasive cutting tool. The effects of combined machining parameters, e g, cutting speed（vs）, feed rate（vf）, and depth of cut（ap）, with the same change of material removal rate（MRR） on the mill-grinding force and surface roughness（Ra） were investigated. The formation mechanism of typical machined surface defects was analyzed by SEM. The experimental results reveal that with the same change of material removal rate, lower mill-grinding force values can be gained by increasing depth of cut and feed rate simultaneously at higher cutting speed. With the same change of MRR value, lower surface roughness values can be gained by increasing the feed rate at higher cutting speed, rather than just increasing the depth of cut, or increasing the feed rate and depth of cut simultaneously. The machined surface of Si Cp/Al composites reveals typical defects which can influence surface integrity.

Liquid-Phase-Impacting Diffusion Welding Mechanism and Microstructure of Welded Joint of Al Matrix Composite SiCp/101A

The liquid-phase-impacting (LPI) diffusion welding mechanism and microstructure of welded joint of aluminum matrixcomposite SiCp/101A have been studied. It shows that by LPl diffusion welding, the interface state between SiCparticle and matrix is prominent, the harmful microstructure or brittle phase can be restrained from the welded joint.Moreover, the density of dislocation in the matrix near the interface and in the matrix are all so higher than that ofparent composite, the dislocation entwists each other intensively resulted in welding the composite successfully.

Effect of aging treatment on mechanical properties of (SiCw+SiCp)/2024Al hybrid nanocomposites

2024Al based composites reinforced by a hybrid of SiC whisker and SiC nanoparticle were fabricated by a squeeze casting route. In the (SiCw+SiCp)/Al composites, the volume fraction of SiC whisker is 20% and that of SiC nanoparticle is 2%, 5% and 7%, respectively. The as cast composites were solution treated followed by aging treatment. The experimental results show that the SiC nanoparticles are more effective in improving the hardness and tensile strength of the composites than SiC whiskers. The hardening kinetics of the composites is enhanced by reinforcements addition and the peak aging time is 4-5 h. The hardness of all the hybrid composite decreases at the initial aging stage, suggesting that dislocation recovery softening process coexists with precipitation hardening. DSC study shows that the GP zone formation of the hybrid composites is suppressed.

Investigation on Material Response of 55% SiCp/Al Composites Induced by Pulsed Laser

Silicon carbide particle reinforced aluminum matrix composites(SiCp/Al composites)are widely used in aviation,aerospace and electronic package.However,low machining efficiency,severe tool wear and poor surface quality are severe during the machining of SiCp/Al composites.Laser-induced oxidation is capable to improve the machinability of SiCp/Al composites.The material response of 55%(volume fraction)SiCp/Al composites induced by a nanosecond pulsed laser is studied.A metamorphic layer which is composed of an oxide layer and sub-layer is produced.The effects of reaction surrounding and laser average power on the microstructure and thickness of the oxide layer and sub-layer are investigated.Experimental results show that:A thicker oxide layer and a sub-layer are formed in an oxygen-rich atmosphere.The oxides are mainly composed of 2Al2O3·SiO2(mullite).A positive correlation between the laser average power and thicknesses of oxide layers and sub-layers is found.A loose oxide layer of 138μm and a sub-layer of 21μm are formed at the laser average power of 6 W,laser scanning pitch of 10μm,and laser scanning speed of 1 mm/s under an oxygen-rich atmosphere.The high efficient machining of Si Cp/Al composites can be realized by laser-induced oxidation.

Microstructural characteristics of in situ Mg_2Si/Al-Si composite by low superheat pouring

To control the morphology and size of the primary and eutectic Mg2Si phases in in situ Mg2Si/Al-Si composite and achieve a feasible and reliable technique to produce appropriate feedstock for the thixo-casting and rheo-casting of this type of material, three AI-Si matrix composites reinforced by 5wt.%, 9wt.% and 17wt.% Mg2Si with hypoeutectic, eutectic and hypereutectic compositions were prepared by the low superheat pouring （LSP） process. The effects of the pouring temperature （superheat） on the morphology and size distribution of primary phases （primary e-AI and Mg2Si）, binary （a-AI ＋ Mg2Si） eutectic cell and eutectic Mg2Si were investigated. The experimental results show that low pouring temperature （superheat） not only refines the grain structure of the primary e-AI and binary （e-AI ＋ Mg2Si） eutectic cell in three composites and promotes the formation of more non- dendritic structural semi-solid metal （SSM） slurry of these phases; but also refines the primary and eutectic Mg2Si phases, which seems to be attributed to the creation of an ideal condition for the nucleation and the acquisition of a high survival of nuclei caused by the LSP process.

Laser Cladding Al-Si/Al_2O_3-TiO_2 Composite Coatings on AZ31B Magnesium Alloy

To improve the wear resistance and corrosion resistance of magnesium alloys, a 5 kW continuous wave CO2 laser was used to investigate the laser surface cladding on AZ31 B magnesium alloys with Al-Si/Al2O3-TiO2 composite powders. A detailed microstructure, chemical composition, and phase analysis of the composite coatings were studied by scanning electron microscopy （SEM）, energy dispersive spectroscopy （EDS）, and X-ray diffraction （XRD）. The laser cladding shows good metallurgical bonding with the substrate. The composite coatings are composed of Mgl7Al12, Al3Mg2, Mg2Si, Al2O3, and TiO2 phases. Compared to the average microhardness （50HV0.05） of the AZ3 1 B substrate, that of the composite coatings （230HV0.05） is improved significantly. The wear resistances of the surface layers were evaluated in detail. The results demonstrate that the wear resistances of the laser surface-modified samples are considerably improved compared to the substrate. It also show that the composite coatings exhibit better corrosion resistance than that of the substrate in 3.5wt% NaCI solution.