Nickel and nickel-ceria catalysts supported on high surface area silica, with 6 wt% Ni and 20 wt% CeO2 were prepared by microwave assisted(co) precipitation method. The catalysts were investigated by XRD,TPR and XPS a...Nickel and nickel-ceria catalysts supported on high surface area silica, with 6 wt% Ni and 20 wt% CeO2 were prepared by microwave assisted(co) precipitation method. The catalysts were investigated by XRD,TPR and XPS analyses and they were tested in partial oxidation of methane(CPO). The catalytic reaction was carried out at atmospheric pressure in a temperature range of 400–800℃ with a feed gas mixture containing methane and oxygen in a molecular ratio CH4/O2=2. The Ni catalyst exhibited 60% methane conversion with 60% selectivity to CO already at 500℃. On the contrary, the Ni–Ce catalyst was inert to CPO up to 700℃. Moreover, the former catalyst reproduced its activity at the descending temperatures maintaining a good stability at 600℃, over a reaction time of 80 h, whereas the latter one completely deactivated. Test of CH4 temperature programmed surface reaction(CH4-TPSR) revealed a higher methane activation temperature(> 100℃) for the Ni–Ce catalyst as compared to the Ni one. Noticeable improvement of the ceria containing catalyst occurred when the reaction test started at a temperature higher than the methane decomposition temperature. In this case, the sample achieved the same catalytic behavior of the Ni catalyst. As confirmed by XPS analyses, the distinct electronic state of the supported nickel was responsible for the differences in catalytic behavior.展开更多
Cu/ZrO2/SiO2 are efficient catalysts for the selective hydrogenation of CO2 to CH3OH. In order to understand the role of ZrO2 in these mixed-oxides based catalysts, in situ X-ray absorption spectroscopy has been carri...Cu/ZrO2/SiO2 are efficient catalysts for the selective hydrogenation of CO2 to CH3OH. In order to understand the role of ZrO2 in these mixed-oxides based catalysts, in situ X-ray absorption spectroscopy has been carried out on the Cu and Zr K-edge. Under reaction conditions, Cu remains metallic, while Zr is present in three types of coordination environment associated with 1) bulk ZrO2, 2) coordinatively saturated and 3) unsaturated Zr(Ⅳ) surface sites. The amount of coordinatively unsaturated Zr surface sites can be quantified by linear combination fit of reference X-Ray absorption near edge structure (XANES) spectra and its amount correlates with CH3OH formation rates, thus indicating the importance of Zr(Ⅳ) Lewis acid surface sites in driving the selectivity toward CH3OH. This finding is consistent with the proposed mechanism, where CO2 is hydrogenated at the interface between the Cu nanoparticles that split H2 and Zr(Ⅳ) surface sites that stabilizes reaction intermediates.展开更多
VOx/SiO2 catalysts prepared by impregnation method were used for catalytic dehydrogenation of n-butane to butenes and characterized by X-ray diffraction, FT-IR, UV-vis, Raman, and BET measurements. The effects of VOx ...VOx/SiO2 catalysts prepared by impregnation method were used for catalytic dehydrogenation of n-butane to butenes and characterized by X-ray diffraction, FT-IR, UV-vis, Raman, and BET measurements. The effects of VOx loading and the reaction temperature on the VOx/SiO2 catalysts and their catalytic performances for the dehydrogenation of n-butane were studied. When the VOx loading was 12% g/gcat and reaction temperature was between 590 ℃ and 600℃, n-butane conversion and butenes yields reached the highest value under H2 flux of 10 ml/min and n-butane flux of 10 ml/min. Product distribution, such as the ratio of 2-butene to 1-butene and the ratio of cis-2-butene to trans-2-butene, was mainly influenced by the reaction temperature.展开更多
Aluminated mesoporous silica was prepared by multiple post-grafting of alumina onto uniform mesoporous SiO2 ,which was assembled from monodisperse SiO2 microspheres.Hydrodesulfurization（HDS）catalyst was prepared by ...Aluminated mesoporous silica was prepared by multiple post-grafting of alumina onto uniform mesoporous SiO2 ,which was assembled from monodisperse SiO2 microspheres.Hydrodesulfurization（HDS）catalyst was prepared by loading Ni and Mo active components onto the aluminated uniform mesoporous SiO2 ,and its HDS catalytic performance was evaluated using hydrodesulfurization of dibenzothiophene as the probe reaction at 300℃ and 6.0 MPa in a tubular reactor.The samples were characterized by N2 physisorption,scanning electronic microscopy,Fourier transform infrared spectrum,X-ray diffraction（XRD）,temperature-programmed desorption of ammonia（NH3-TPD）,^27Al nuclear magnetic resonance（^27Al-NMR）and high-resolution transmission electron microscopy（HRTEM）.The results showed that the Si–OH group content of SiO2 was mainly dependent on the pretreatment conditions and had significant influence on the activity of the Ni Mo catalyst.The surface properties of the aluminated SiO2 varied with the Al2O3-grafting cycles.Generally after four cycles of grafting,the aluminated SiO2 behaved like amorphous alumina.In addition,plotting of activity of Ni Mo catalysts supported on aluminated meso–macroporous silica materials against the Al2O3-grafting cycle yields a volcano curve.展开更多
A facile and user friendly technique to immobilize the late-transition metal complexes on spherical MgCl2/SiO2/THF support has been developed. The spherical MgCl2/SiO2/THF-supported late-transition metal catalysts 2,6...A facile and user friendly technique to immobilize the late-transition metal complexes on spherical MgCl2/SiO2/THF support has been developed. The spherical MgCl2/SiO2/THF-supported late-transition metal catalysts 2,6-bis-[1-(2,6-dimethylphenylimino)ethyl]pyridine iron(II) dichloride(SC-A) and 1,4-bis(2,6-dimethylphenyl)- acenaphthene diimine nickel(II) dibromide(SC-B) for ethylene polymerization has been prepared by spray-drying technique using tetrahydrofuran suspension containing MgCl2, SiO2 and late-transition metal complexes. The catalysts were characterized by BET, XRD, SEM and the polymers were analyzed using GPC, DSC and 13C-NMR. The test results show that spray-drying is a very effective method for immobilizing late-transition metal catalysts for ethylene polymerization. Among six kinds of cocatalysts for olefin polymerization, TMA and TEA were confirmed to be more effective than other compounds for the ethylene polymerization system using the catalyst SC-A. For the case of the catalyst SC-B, DEAC showed the best performance as cocatalysts in ethylene polymerization. The replication of the catalyst morphology was found in the resultant polyethylene.展开更多
基金The Executive Programme for Cooperation between Italy and India (Prot.No.MAE01054762017)。
文摘Nickel and nickel-ceria catalysts supported on high surface area silica, with 6 wt% Ni and 20 wt% CeO2 were prepared by microwave assisted(co) precipitation method. The catalysts were investigated by XRD,TPR and XPS analyses and they were tested in partial oxidation of methane(CPO). The catalytic reaction was carried out at atmospheric pressure in a temperature range of 400–800℃ with a feed gas mixture containing methane and oxygen in a molecular ratio CH4/O2=2. The Ni catalyst exhibited 60% methane conversion with 60% selectivity to CO already at 500℃. On the contrary, the Ni–Ce catalyst was inert to CPO up to 700℃. Moreover, the former catalyst reproduced its activity at the descending temperatures maintaining a good stability at 600℃, over a reaction time of 80 h, whereas the latter one completely deactivated. Test of CH4 temperature programmed surface reaction(CH4-TPSR) revealed a higher methane activation temperature(> 100℃) for the Ni–Ce catalyst as compared to the Ni one. Noticeable improvement of the ceria containing catalyst occurred when the reaction test started at a temperature higher than the methane decomposition temperature. In this case, the sample achieved the same catalytic behavior of the Ni catalyst. As confirmed by XPS analyses, the distinct electronic state of the supported nickel was responsible for the differences in catalytic behavior.
基金E.L.,K.L.,P.W.,and S.T.are supported by the SCCER-Heat and Energy Storage program
文摘Cu/ZrO2/SiO2 are efficient catalysts for the selective hydrogenation of CO2 to CH3OH. In order to understand the role of ZrO2 in these mixed-oxides based catalysts, in situ X-ray absorption spectroscopy has been carried out on the Cu and Zr K-edge. Under reaction conditions, Cu remains metallic, while Zr is present in three types of coordination environment associated with 1) bulk ZrO2, 2) coordinatively saturated and 3) unsaturated Zr(Ⅳ) surface sites. The amount of coordinatively unsaturated Zr surface sites can be quantified by linear combination fit of reference X-Ray absorption near edge structure (XANES) spectra and its amount correlates with CH3OH formation rates, thus indicating the importance of Zr(Ⅳ) Lewis acid surface sites in driving the selectivity toward CH3OH. This finding is consistent with the proposed mechanism, where CO2 is hydrogenated at the interface between the Cu nanoparticles that split H2 and Zr(Ⅳ) surface sites that stabilizes reaction intermediates.
基金The project was supported by Program for New Century Excellent Talents in University (Grant No. NCET-04-0987)Doctor Fund of Science Research of Xinjiang University (Grant No. BS060101).
文摘VOx/SiO2 catalysts prepared by impregnation method were used for catalytic dehydrogenation of n-butane to butenes and characterized by X-ray diffraction, FT-IR, UV-vis, Raman, and BET measurements. The effects of VOx loading and the reaction temperature on the VOx/SiO2 catalysts and their catalytic performances for the dehydrogenation of n-butane were studied. When the VOx loading was 12% g/gcat and reaction temperature was between 590 ℃ and 600℃, n-butane conversion and butenes yields reached the highest value under H2 flux of 10 ml/min and n-butane flux of 10 ml/min. Product distribution, such as the ratio of 2-butene to 1-butene and the ratio of cis-2-butene to trans-2-butene, was mainly influenced by the reaction temperature.
基金Financial support by the National Natural Science Foundation of China (Grant No. 91534120)the Shanghai Petrochemical Company of Sinopec (under the contract number 30450127-13-ZC0607-0001)
文摘Aluminated mesoporous silica was prepared by multiple post-grafting of alumina onto uniform mesoporous SiO2 ,which was assembled from monodisperse SiO2 microspheres.Hydrodesulfurization（HDS）catalyst was prepared by loading Ni and Mo active components onto the aluminated uniform mesoporous SiO2 ,and its HDS catalytic performance was evaluated using hydrodesulfurization of dibenzothiophene as the probe reaction at 300℃ and 6.0 MPa in a tubular reactor.The samples were characterized by N2 physisorption,scanning electronic microscopy,Fourier transform infrared spectrum,X-ray diffraction（XRD）,temperature-programmed desorption of ammonia（NH3-TPD）,^27Al nuclear magnetic resonance（^27Al-NMR）and high-resolution transmission electron microscopy（HRTEM）.The results showed that the Si–OH group content of SiO2 was mainly dependent on the pretreatment conditions and had significant influence on the activity of the Ni Mo catalyst.The surface properties of the aluminated SiO2 varied with the Al2O3-grafting cycles.Generally after four cycles of grafting,the aluminated SiO2 behaved like amorphous alumina.In addition,plotting of activity of Ni Mo catalysts supported on aluminated meso–macroporous silica materials against the Al2O3-grafting cycle yields a volcano curve.
基金supported by the National Natural Science Foundation of China (Grant No.U1162114)the Science Foundation of Tianjin University of Science & Technology (20090420)
文摘A facile and user friendly technique to immobilize the late-transition metal complexes on spherical MgCl2/SiO2/THF support has been developed. The spherical MgCl2/SiO2/THF-supported late-transition metal catalysts 2,6-bis-[1-(2,6-dimethylphenylimino)ethyl]pyridine iron(II) dichloride(SC-A) and 1,4-bis(2,6-dimethylphenyl)- acenaphthene diimine nickel(II) dibromide(SC-B) for ethylene polymerization has been prepared by spray-drying technique using tetrahydrofuran suspension containing MgCl2, SiO2 and late-transition metal complexes. The catalysts were characterized by BET, XRD, SEM and the polymers were analyzed using GPC, DSC and 13C-NMR. The test results show that spray-drying is a very effective method for immobilizing late-transition metal catalysts for ethylene polymerization. Among six kinds of cocatalysts for olefin polymerization, TMA and TEA were confirmed to be more effective than other compounds for the ethylene polymerization system using the catalyst SC-A. For the case of the catalyst SC-B, DEAC showed the best performance as cocatalysts in ethylene polymerization. The replication of the catalyst morphology was found in the resultant polyethylene.
