Signal-to-noise ratio of lensless ghost interference with thermal incoherent light

Factors influencing the signal-to-noise ratio （SNR） of lensless ghost interference with thermal incoherent light are investigated. Our result shows that the SNR of lensless ghost interference is related to the transverse length of the object, the position of the object in the imaging system and the transverse size of the light source. Furthermore, the effects of these factors on the SNR are discussed in detail by numerical simulations.

Signal-to-noise ratio comparison of angular signal radiography and phase stepping method

Grating-based x-ray phase contrast imaging has the potential to be applied in future medical applications as it is compatible with both laboratory and synchrotron source. However, information retrieval methods are important because acquisition speed, scanning mode, image quality, and radiation dose depend on them. Phase-stepping （PS） is a widely used method to retrieve information, while angular signal radiography （ASR） is a newly established method. In this manuscript, signal-to-noise ratios （SNRs） of ASR are compared with that of PS. Numerical experiments are performed to validate theoretical results. SNRs comparison shows that for refraction and scattering images ASR has higher SNR than PS method, while for absorption image both methods have same SNR. Therefore, our conclusions would have guideline in future preclinical and clinical applications.

Long term integration of radar signals with unknown Doppler shift for ubiquitous radar

Ubiquitous radar is a new radar system that provides continuous and uninterrupted multifunction capability within a coverage volume. Continuous coverage from close-in ＂pop-up＂ targets in clutter to long-range targets impacts selection of waveform parameters. The coherent processing interval （CPI） must be long enough to achieve a certain signal-to-noise ratio （SNR） that ensures the efficiency of detection. The condition of detection in the case of low SNR is analyzed, and three different cases that would occur during integration are discussed and a method to determine the CPI is presented. The simulation results show that targets detection with SNR as low as -26 dB in the experimental system can possibly determine the CPI.

A NOVEL METHOD FOR ESTIMATING THE SNR OF UNKNOWN EMITTER SIGNAL

It is important to estimate the Signal-to-Noise Ratio(SNR) of unknown emitter signal accurately.In order to resolve the disadvantages of present algorithm,a novel method is proposed in this letter.We extract and normalize the information of zero frequency of received signal by the Wigner-Vile Distribution(WVD) transformation and then get the approximate power of original signal by mathematic transformation,at last,we get the estimate value of SNR by the known account formula of SNR.Simulation results show that it is correct and feasible.

THE METHOD OF SEPARATING HARMONIC SIGNALS FROM MULTIPLICATIVE AND ADDITIVE NOISES

This paper focuses on the extraction of a harmonic signal from multiplicative and additive noises. A method is proposed in two stages： （1） to square the original discrete time series, which includes both signals and noises, and form a new time series. By this means, the multiplicative noise is converted to additive noise; and （2） to filter out the noise by using existing noise removal schemes. With a large amount of simulation, experimental results demonstrated the efficiency and effectiveness of this newly developed method in terms of Signal-to-Noise Ratio （SNR） and other criteria. Prom the experiment, it is also found that： the two kinds of noises affect the SNR differently. In general, the SNR is not influenced by multiplicative Gaussian noise regardless of its variance. However, if both kinds of noise exist, the SNR decreases with the incensement of the Variance of Additive Noise to Multiplicative Noise Ratio （VAMNR）. This analysis is also supported by simulation work.

Network Sorting Algorithm of Multi-Frequency Signal with Adaptive SNR

An signal noise ratio（ SNR） adaptive sorting algorithm using the time-frequency（ TF）sparsity of frequency-hopping（ FH） signal is proposed in this paper. Firstly,the Gabor transformation is used as TF transformation in the system and a sorting model is established under undetermined condition; then the SNR adaptive pivot threshold setting method is used to find the TF single source. The mixed matrix is estimated according to the TF matrix of single source. Lastly,signal sorting is realized through improved subspace projection combined with relative power deviation of source. Theoretical analysis and simulation results showthat this algorithm has good effectiveness and performance.

Application Research of Image Compression Technology in Monitoring System of Rape Crop in Areas of Qinling Mountains

[Objective] The aim was to present a proposal about a new image compression technology, in order to make the image be able to be stored in a smaller space and be transmitted with smaller bit rate on the premise of guaranteeing image quality in the rape crop monitoring system in Qinling Mountains. [Method] In the proposal, the color image was divided into brightness images with three fundamental colors, followed by sub-image division and DCT treatment. Then, coefficients of transform domain were quantized, and encoded and compressed as per Huffman coding. Finally, decompression was conducted through inverse process and decompressed images were matched. [Result] The simulation results show that when compression ratio of the color image of rape crops was 11.972 3∶1, human can not distinguish the differences between the decompressed images and the source images with naked eyes; when ratio was as high as 53.565 6∶1, PSNR was still above 30 dD,encoding efficiency achieved over 0.78 and redundancy was less than 0.22. [Conclusion] The results indicate that the proposed color image compression technology can achieve higher compression ratio on the premise of good image quality. In addition, image encoding quality and decompressed images achieved better results, which fully met requirement of image storage and transmission in monitoring system of rape crop in the Qinling Mountains.

Micro-Doppler feature extraction of micro-rotor UAV under the background of low SNR

Micro-Doppler feature extraction of unmanned aerial vehicles(UAVs)is important for their identification and classification.Noise and the motion state of the UAV are the main factors that may affect feature extraction and estimation precision of the micro-motion parameters.The spectrum of UAV echoes is reconstructed to strengthen the micro-motion feature and reduce the influence of the noise on the condition of low signal to noise ratio(SNR).Then considering the rotor rate variance of UAV in the complex motion state,the cepstrum method is improved to extract the rotation rate of the UAV,and the blade length can be intensively estimated.The experiment results for the simulation data and measured data show that the reconstruction of the spectrum for the UAV echoes is helpful and the relative mean square root error of the rotating speed and blade length estimated by the proposed method can be improved.However,the computation complexity is higher and the heavier computation burden is required.

A Blackman-Harris windowed triple-spectrum-line interpolation method for measuring SNR of ADCs

In the practical measurement of signal to noise ratio(SNR)of analog-to-digital converters(ADCs)by using fast Fourier transformation(FFT)method,the non-coherent sampling is inevitable,leading to spectral leakage which in turn affects the calculation accuracy and final measurement results.In this paper,a new method based on the Blackman-Harris windowed triple-spectrum-line interpolation is presented for the measurement of ADCs SNR by FFT.The simulation platform is built based on MATLAB and the behavioral dynamic models of the high-speed ADC products of Analog Devices Inc.(ADI)are simulated.The simulation results show that,even in the case of the maximum non-coherent degree,the SNR error is less than0.23dB and reaches the testing standards provided by ADI,confirming that the proposed method is effective for suppressing the spectral leakage effects and improving the SNR test accuracy.

The effect of different number of diffusion gradients on SNR of diffusion tensor-derived measurement maps

Diffusion tensor imaging (DTI) is mainly applied to white matter fiber tracking in human brain, but there is still a debate on how many diffusion gradient directions should be used to get the best results. In this paper, the performance of 7 protocols corresponding to 6, 9, 12, 15, 20, 25, and 30 noncollinear number of diffusion gradi-ent directions (NDGD) were discussed by com-paring signal-noise ratio (SNR) of tensor- de-rived measurement maps and fractional ani-sotropy (FA) values. All DTI data (eight healthy volunteers) were downloaded from the website of Johns Hopkins Medical Institute Laboratory of Brain Anatomi-cal MRI with permission. FA, apparent diffusion constant mean (ADC-mean), the largest eigen-value (LEV), and eigenvector orientation (EVO) maps associated with LEV of all subjects were calculated derived from tensor in the 7 proto-cols via DTI Studio. A method to estimate the variance was presented to calculate SNR of these tensor-derived maps. Mean ±standard deviation of the SNR and FA values within re-gion of interest (ROI) selected in the white mat-ter were compared among the 7 protocols. The SNR were improved significantly with NDGD increasing from 6 to 20 (P<0.05). From 20 to 30, SNR were improved significantly for LEV and EVO maps (P<0.05), but no significant dif-ferences for FA and ADC-mean maps (P>0.05). There were no significant variances in FA val-ues within ROI between any two protocols (P>0.05). The SNR could be improved with NDGD in-creasing, but an optimum protocol is needed because of clinical limitations.

Photoelectric detection technology of laser seeker signals

The measurement of the rolling angle of the projectile is one of the key technologies for the terminal correction projectile.To improve the resolution accuracy of the rolling angle in the laser seeker weapon system, the imaging model of the detector, calculation model of the position and the signal-to-noise ratio(SNR) model of the circuit are built to derive both the correlation between the resolution error of the rolling angle and the spot position, and the relation between the position resolution error and the SNR. Then the influence of each parameter on the SNR is analyzed at large,and the parameters of the circuit are determined. Meanwhile, the SNR and noise voltage of the circuit are calculated according to the SNR model and the decay model of the laser energy. Finally,the actual photoelectric detection circuit is built, whose SNR is measured to be up to 53 d B. It can fully meet the requirement of0.5° for the resolution error of the rolling angle, thereby realizing the analysis of critical technology for photoelectric detection of laser seeker signals.

RESEARCH ON PERFORMANCE INFLUENCE OF DIRECT-PATH SIGNAL FOR DVB-S BASED PASSIVE RADAR

Passive radar detects moving targets by Cross Ambiguity Function (CAF), which is based on the cross correlation process of the direct-path signal in reference channel and echo signal in receive channel. Thus, the performance of direct-path signal is important to system performance for this type of radar. While the Signal to Noise Ratio (SNR) of direct-path signal is low, it will deteriorate the detection performance. In this paper, how SNR of direct-path signal induces degradation on the SNR of CAF, and how the integration gain affects by integration time are analyzed, both with theoretical analysis and numerical simulation, which are valuable for the R&D of passive radar.

Implication of two-coupled tri-stable stochastic resonance in weak signal detection

Stochastic resonance （SR） has been proved to be an effective approach to extract weak signals overwhelmed in noise. However, the detection effect of current SR models is still unsatisfactory. Here, a coupled tri-stable stochastic resonance （CTSSR） model is proposed to further increase the output signal-to-noise ratio （SNR） and improve the detection effect of SR. The effects of parameters a, b, c, and r in the proposed resonance system on the SNR are studied, by which we determine a set of parameters that is relatively optimal to implement a comparison with other classical SR models. Numerical experiment results indicate that this proposed model performs better in weak signal detection applications than the classical ones with merits of higher output SNR and better anti-noise capability.

Nonsaturation Throughput Enhancement of IEEE 802.11b Distributed Coordination Function for Heterogeneous Traffic under Noisy Environment

In this paper, we propose a mechanism named modified backoff （MB） mechanism to decrease the channel idle time in IEEE 802.11 distributed coordination function （DCF）. In the noisy channel, when signal-to-noise ratio （SNR） is low, applying this mechanism in DCF greatly improves the throughput and lowers the channel idle time. This paper presents an analytical model for the performance study of IEEE 802.11 MB-DCF for nonsaturated heterogeneous traffic in the presence of transmission errors. First, we introduce the MB-DCF and compare its performance to IEEE 802.11 DCF with binary exponential backoff （BEB）. The IEEE 802.11 DCF with BEB mechanism suffers from more channel idle time under low SNR. The MB-DCF ensures high throughput and low packet delay by reducing the channel idle time under the low traffic in the network. However, to the best of the authors＇ knowledge, there are no previous works that enhance the performance of the DCF under imperfect wireless channel. We show through analysis that the proposed mechanism greatly outperforms the original IEEE 802.11 DCF in the imperfect channel condition. The effectiveness of physical and link layer parameters on throughput performance is explored. We also present a throughput investigation of the heterogeneous traffic for different radio conditions.

A New Image Denoising Scheme Using Soft-Thresholding

The VisuShrink is one of the important image denoising methods. It however does not provide good quality of image due to removing too many coefficients especially using soft-thresholding technique. This paper proposes a new image denoising scheme using wavelet transformation. In this paper, we modify the coefficients using soft-thresholding method to enhance the visual quality of noisy image. The experimental results show that our proposed scheme has better performance than the VisuShrink in terms of peak signal-to-noise ratio (PSNR) i.e., visual quality of the image.

On the Small SNR Processing Ability of IR Point Target Detection

Three-dimensional (3-D) matched filtering has been suggested as a powerful processing technique for detecting weak, moving IR point target immersed in a noisy field. Based on the theory of the 3-D matched filtering and the optimal linear processing, the optimal point target detector is being analyzed in this paper. The performance of the detector is introduced in detail. The results provide a standard reference to evaluate the performance of any other point target detection algorithms.

An Adaptive Method of Image CompressionBased on Wavelet Analysis

Through research for image compression based on wavelet analysis in recent years, we put forward an adaptive wavelet decomposition strategy. Whether sub-images are to be decomposed or not are decided by their energy defined by certain criterion. Then we derive the adaptive wavelet decomposition tree (AWDT) and the way of adjustable compression ratio. According to the feature of AWDT, this paper also deals with the strategies which are used to handle different sub-images in the procedure of quantification and coding of the wavelet coefficients. Through experiments, not only the algorithm in the paper can adapt to various images, but also the quality of recovered image is improved though compression ratio is higher and adjustable. When their compression ratios are near, the quality of subjective vision and PSNR of the algorithm are better than those of JPEG algorithm.

New Wavelet Thresholding Algorithm in Dropping Ambient Noise from Underwater Acoustic Signals

Underwater Wireless Communication, largely dependent on the acoustic communication between the machines, is largely affected by various types of noise in the shallow and deep water. However ambient noise which is due to multiple sources (e.g. shipping, wind) and no one source dominates. Ambient noise masks the acoustic signal to a large extent. Hence today it has drawn the attention of the experts to reduce its effect on the received signal. This paper discusses ambient noise problem and devises a new wavelet thresholding method to reduce its effect. Afterwards a comparative study on statistical parameters is shown to prove the efficiency of the devised method.

Hardware implementation of adaptive filter for noise cancellation using TMS320C6713

Daily, we experience the effects of audio noise, which contaminates the original information bearing signal with noise from its surrounding environment. This paper focuses on real-time hardware implementation of multi-tap adaptive noise cancellation （ANC） system by using the least mean square （LMS） algorithm on TMS320C6713 to remove undesired noise from a received signal for various audio related applications. Three different experiments are carried out by considering different audio inputs to test the efficiency of the designed ANC system. The ＇C＇ code implementation of LMS algorithm is introduced and simulated in code composer studio （CCS）, then realized on the digital signal processor （DSP） C6713. The 300 Hz, 500 Hz, 800 Hz, 1 kHz and 3 kHz of tone signals and male speech signal are used as the reference inputs to trace the noise of signal until it is eliminated. The performance of ANC system is studied in terms of convergence speed, order of the filter and signal-to-noise ratio （SNR）. The experimentam results demonstrate that the designed system shows a consider- able improvement in SNR.

Noise properties of multi-combination information in x-ray grating-based phase-contrast imaging

Grating-based x-ray phase contrast imaging has attracted increasing interest in recent decades as multimodal and laboratory source usable method.Specific efforts have been focused on establishing a new extraction method to perform practical applications.In this work,noise properties of multi-combination information of newly established information extraction method,so-called angular signal radiography method,are investigated to provide guidelines for targeted and specific applications.The results show that how multi-combination of images can be used in targeted practical applications to obtain a high-quality image in terms of signal-to-noise ratio.Our conclusions can also hold true for upcoming targeted practical applications such as biomedical imaging,non-destructive imaging,and materials science.