For reducing the core loss of grain oriented silicon steel and improving its aging property, a new method, the LLSA by using Sb as the laser surface alloying element, was investigated, and at proper technique conditio...For reducing the core loss of grain oriented silicon steel and improving its aging property, a new method, the LLSA by using Sb as the laser surface alloying element, was investigated, and at proper technique conditions rather good result was obtained.展开更多
A mechanism of oxygen transportation in Czochralski growth of silicon crystals under a horizontal magnetic field (HMCZ) is proposed. Oxygen depleted surface melt, driven to the growth interface by the thermal Marangon...A mechanism of oxygen transportation in Czochralski growth of silicon crystals under a horizontal magnetic field (HMCZ) is proposed. Oxygen depleted surface melt, driven to the growth interface by the thermal Marangoni flow, determines oxygen concentration in the grown crystals. Systematic study was carried out to investigate effects of growth parameters on oxygen incorporation into crystals.展开更多
The P + Sr + Ce compound modification technologies of as-cast Al-21Si-1.5Cu-1.5Ni- 2.5Fe- 0.5Mg alloy were investigated by means of orthogonal test. Orthogonal test results show that 3% (CaH2PO4 + 2CASO4)+ 0.2%...The P + Sr + Ce compound modification technologies of as-cast Al-21Si-1.5Cu-1.5Ni- 2.5Fe- 0.5Mg alloy were investigated by means of orthogonal test. Orthogonal test results show that 3% (CaH2PO4 + 2CASO4)+ 0.2%Sr + 0.2%Ce is the optimum additive of modification treatment which can fine eutectic and primary silicon also can change the form of rich-iron phase at same time. The needle form of rich-iron phase is Al9FeSi3, which is prored by X-ray diffraction analysis and X-ray energy spectrum analysis. After compound modification treatment, the needle form of rich-iron phase disappeared and the fish bone form of rich-iron and rich-Ce phase that is AlsCeFe emerged. Both at room temperature and at 300℃, the tensile strength of the alloy after the modification treatment with the optimum additive is 30% lager than that of the alloy unmodified. Observed by SEM, the brittle intercrystalline tensile fracture changed into a blended one in which has many dimples.展开更多
A high Fe containing aluminum matrix filler metal for hardfacing aluminum silicon alloys has been developed by using iron,nickel,and silicon as the major strengthening elements,and by measuring mechanical properties...A high Fe containing aluminum matrix filler metal for hardfacing aluminum silicon alloys has been developed by using iron,nickel,and silicon as the major strengthening elements,and by measuring mechanical properties,room temperature and high temperature wear tests,and microstructural analysis.The filler metal,which contains 3.0%-5.0% Fe and 11.0%-13.0% Si,exhibits an excellent weldability.The as cast and as welded microstructures for the filler metal are of uniformly distribution and its dispersed network of hard phase is enriched with Al Si Fe Ni.The filler metal shows high mechanical properties and wear resistance at both room temperature and high temperatures.The deposited metal has a better resistance to impact wear at 220℃ than that of substrate Al Si Mg Cu piston alloy;at room temperature,the deposited metal has an equivalent resistance to slide wear with lubrication as that of a hyper eutectic aluminum silicon alloy with 27% Si and 1% Ni.展开更多
Anovel silicon containing carbon precursor was synthesised by reacting a petroleum pitchfraction and polydimethylsilane. The precursor containing about 26wt% Si was meltspunintofibresand then oxidativelystabilised in...Anovel silicon containing carbon precursor was synthesised by reacting a petroleum pitchfraction and polydimethylsilane. The precursor containing about 26wt% Si was meltspunintofibresand then oxidativelystabilised in airto renderthefibresinfusiblebefore pyrolysisat1200℃underinertatmospheretoproduceC Sialloy( CSA) fibres. Theextentofstabili sation wasfoundto becriticalto the development of mechanicalstrength of thefibres which varied with heattreatmenttemperature, showing a maximum at 1200 ℃when thestrength was 1 4 1 6 GPa. Thesestrengthsareremarkably goodconsideringthelow modulus whichis duetothe quite high failurestrains. Thefibrescanshow excellentresistanceto oxidation if given an initialshortexposureto oxygen athigh temperature duetotheformation of an im perceptiblelayer of silica. CSAfibreshavethe advantagesof both carbon fibresand SiCfi bres,thusextended application areascan beenvisaged .展开更多
The effects of La addition on the microstructure and tensile properties of B-refmed and Sr-modified A1-1 1Si-1.5Cu-0.3Mg cast- ing alloys were investigated. With a trace addition of La (0.05wt%-0. lwt%), the mutual ...The effects of La addition on the microstructure and tensile properties of B-refmed and Sr-modified A1-1 1Si-1.5Cu-0.3Mg cast- ing alloys were investigated. With a trace addition of La (0.05wt%-0. lwt%), the mutual poisoning effect between B and Sr can be neutral- ized by the formation of LaB6 rather than SrB6. By employing a La/B weight ratio of 2:1, uniform microstructures, which are characterized by well refined ct-A1 grains and adequately modified eutectic Si particles as well as the incorporation of precipitated strengthening intermetal- lics, are obtained and lead to appreciable tensile properties with an ultimate tensile strength of 270 MPa and elongation of 5.8%.展开更多
The effects of Ce on the secondary dendrite arm spacing(SDAS) and mechanical behavior of Al-Si-Cu-Mg alloys were investigated. The reduction of SDAS at different Ce concentrations was evaluated in a directional soli...The effects of Ce on the secondary dendrite arm spacing(SDAS) and mechanical behavior of Al-Si-Cu-Mg alloys were investigated. The reduction of SDAS at different Ce concentrations was evaluated in a directional solidification experiment via computer-aided cooling curve thermal analysis(CA-CCTA). The results showed that 0.1wt%-1.0wt% Ce addition resulted in a rapid solidification time, ?ts, and low solidification temperature, ?T_S, whereas 0.1wt% Ce resulted in a fast solidification time, Δ^(ta-Al), of the α-Al phase. Furthermore, Ce addition refined the SDAS, which was reduced to approximately 36%. The mechanical properties of the alloys with and without Ce were investigated using tensile and hardness tests. The quality index(Q) and ultimate tensile strength of(UTS) Al-Si-Cu-Mg alloys significantly improved with the addition of 0.1wt% Ce. Moreover, the base alloy hardness was improved with increasing Ce concentration.展开更多
To determine the modifying agents for Al-7Si alloys, microstructure observation and mixing enthalpy analysis using Miedema model for Al-7Si alloy with additions of different rare earth elements were performed, and the...To determine the modifying agents for Al-7Si alloys, microstructure observation and mixing enthalpy analysis using Miedema model for Al-7Si alloy with additions of different rare earth elements were performed, and the effects of rare earth elements on the modifica-tion of eutectic silicon morphology were investigated. The results of mixing enthalpy analysis show that these four rare earth elements, La, Sm, Pr, and Ce, which have the large negative mixing enthalpies with Si, can be selected as modifying agents for eutectic silicon morphology. The element with the largest negative mixing enthalpy is Ce. Furthermore, the microstructures indicate that these four elements can effec-tively modify the eutectic (α)Al-Si crystals in Al-7Si alloy, and the most effective one is also Ce. Differential scanning calorimetry (DSC) results show that the eutectic temperature depressions due to the additions of modifying agents are the important reasons for the modification of eutectic (α)Al-Si crystals.展开更多
In this study, a serpentine channel pouring process was used to prepare the semi-solid A1-20%Si alloy slurry and refine primary Si grains in the alloy. The effects of the pouring temperature, number of curves in the s...In this study, a serpentine channel pouring process was used to prepare the semi-solid A1-20%Si alloy slurry and refine primary Si grains in the alloy. The effects of the pouring temperature, number of curves in the serpentine channel, and material of the serpentine channel on the size of primary Si grains in the semi-solid A1-20%Si alloy slurry were investigated. The results showed that the pouting temperature, number of the curves, and material of the channel strongly affected the size and distribution of the primary Si grains. The pouring tempera- ture exerted the strongest effect, followed by the number of the curves and then the material of the channel. Under experimental conditions of a four-curve copper channel and a pouring temperature of 701℃, primary Si grains in the semi-solid A1-20%Si alloy slurry were refined to the greatest extent, and the lath-like grains were changed into granular grains. Moreover, the equivalent grain diameter and the average shape coefficient of primary Si grains in the satisfactory semi-solid A1-20%Si alloy slurry were 24.4 μm and 0.89, respectively. Finally, the re- finement mechanism and distribution rule of primary Si grains in the slurry prepared through the serpentine channel pouring process were analyzed and discussed.展开更多
A high content silicon aluminum alloy(Al-25Si-4Cu-1Mg)coating was prepared on a 2A12 aluminum alloy by supersonic plasma spraying.The morphology and microstructure of the coating were observed and analyzed.The hardnes...A high content silicon aluminum alloy(Al-25Si-4Cu-1Mg)coating was prepared on a 2A12 aluminum alloy by supersonic plasma spraying.The morphology and microstructure of the coating were observed and analyzed.The hardness,elastic modulus,and bonding strength of the coating were measured.The wear resistance of the coating and 2A12 aluminum alloy was studied by friction and wear test.The results indicated that the coating was compact and the porosity was only 1.5%.The phase of the coating was mainly composed ofα-Al andβ-Si as well as some hard particles(Al9Si,Al3.21Si0.47,and CuAl2).The average microhardness of the coating was HV 242,which was greater than that of 2A12 aluminum alloy(HV 110).The wear resistance of the coating was superior to 2A12 aluminum alloy.The wear mechanism of the 2A12 aluminum alloy was primarily adhesive wear,while that of the coating was primarily abrasive wear.Therefore,it is possible to prepare a high content silicon aluminum alloy coating with good wear resistance on an aluminum alloy by supersonic plasma spraying.展开更多
The mechanical properties and friction behaviors of CNT/AlSi10Mg composites produced by spark plasma sintering (SPS) were investigated. The results showed that the densities of the sintered composites gradually increa...The mechanical properties and friction behaviors of CNT/AlSi10Mg composites produced by spark plasma sintering (SPS) were investigated. The results showed that the densities of the sintered composites gradually increased with increasing sintering temperature and that the highest microhardness and compressive strength were achieved in the specimen sintered at 450A degrees C. CNTs dispersed uniformly in the Al-Si10Mg matrix when the addition of CNTs was less than 1.5wt%. However, when the addition of CNTs exceeded 1.5wt%, the aggregation of CNTs was clearly observed. Moreover, the mechanical properties (including the densities, compressive strength, and microhardness) of the composites changed with CNT content and reached a maximum value when the CNT content was 1.5wt%. Meanwhile, the minimum average friction coefficient and wear rate of the CNT/AlSi10Mg composites were obtained with 1.0wt% CNTs.展开更多
The synthetical soft magnetic properties were reported for newly-developed nanocrystalline Fe73.5Cu1Nb0.9 Mo2.1Si13.5B9 and Fe73.5Cu1Nb0.5 Mo2.5Si13.5B9 alloys. The levels of high-frequency losses of the new alloys ar...The synthetical soft magnetic properties were reported for newly-developed nanocrystalline Fe73.5Cu1Nb0.9 Mo2.1Si13.5B9 and Fe73.5Cu1Nb0.5 Mo2.5Si13.5B9 alloys. The levels of high-frequency losses of the new alloys are P3/100k=612 and 670 kWm-3, P2/200k=880 and 973kWm-3, P2/500k=4300 and 4600 kWm-3, P0.5/1000k=860 and 920 kWm-3, respectively. They are significantly lower than those of the superior power Mn-Zn ferrite H7c4. The dependence of core loss on frequency and amplitude flux density has been analyzed. The practical applications of the new alloys to switching mode power supplies with the output power of 1 and 2kW were reported.展开更多
The corrosion-wear behavior of a nanocrystalline Fe_(88)Si_(12) alloy disc coupled with a Si_3N_4 ball was investigated in acid(pH 3) and alkaline(pH 9) aqueous solutions. The dry wear was also measured for re...The corrosion-wear behavior of a nanocrystalline Fe_(88)Si_(12) alloy disc coupled with a Si_3N_4 ball was investigated in acid(pH 3) and alkaline(pH 9) aqueous solutions. The dry wear was also measured for reference. The average friction coefficient of Fe_(88)Si_(12) alloy in the pH 9 solution was approximately 0.2, which was lower than those observed for Fe_(88)Si_(12) alloy in the pH 3 solution and in the case of dry wear. The fluctuation of the friction coefficient of samples subjected to the pH 9 solution also showed similar characteristics. The wear rate in the pH 9 solution slightly increased with increasing applied load. The wear rate was approximately one order of magnitude less than that in the pH 3 solution and was far lower than that in the case of dry wear, especially at high applied load. The wear traces of Fe_(88)Si_(12) alloy under different wear conditions were examined and analyzed by scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy. The results indicated that the tribo-chemical reactions that involve oxidation of the worn surface and hydrolysis of the Si_3N_4 ball in the acid solution were restricted in the pH 9 aqueous solution. Thus, water lubrication can effectively improve the wear resistance of nanocrystalline Fe_(88)Si_(12) alloy in the pH 9 aqueous solution.展开更多
A novel wide-band laser cladding system, with high rate of cladding, has been developed in the present work. The system mainly consisted of a 5kW CO2 laser, an automatic powder feeder and a wide-band scanning rotativ...A novel wide-band laser cladding system, with high rate of cladding, has been developed in the present work. The system mainly consisted of a 5kW CO2 laser, an automatic powder feeder and a wide-band scanning rotative polygon mirror which can produce a linear or rectangular focused laser beam. Using this system, a Ni-Cr-Si-B alloy powder was cladded on the surface of type 321 austenitic stainless steel in order to improve its wear and corrosion resistance. The pitting corrosion, high temperature oxidation and wear tests were conducted in order to evaluate the properties of the laser cladded layer. The results demonstrated that the cladded layer can significantly improve the adhesive wear and pitting corrosion resistance of the substrate. Moreover, the cladded layer exhibited good oxidation resistance, which is almost the same as that of GMR-235D Ni-based superalloy.展开更多
The strength and elongation to fracture of spray deposited Al-Si-Pb alloys were studied as a function of lead content, silicon content, and distance from the centre to periphery of the deposit. It is found that the ul...The strength and elongation to fracture of spray deposited Al-Si-Pb alloys were studied as a function of lead content, silicon content, and distance from the centre to periphery of the deposit. It is found that the ultimate tensile strength, proof stress and elongation to fracture decrease, linearly and exponentially, with the increase in lead content and porosity of the deposit, respectively. Both the strengths and elongation to fracture linearly increase with increasing distance from the centre to periphery of the deposit. The ultimate tensile strength and proof stress are higher at a higher silicon content and they have a linear relationship with the hardness of the deposit.展开更多
Aluminum silicon titanium master alloys were prepared in the laboratory by electrolysis of silica and titania dissolved in cryolite alumina melts. Alloys containing up to 12 mass% Si and 2.6 mass% Ti were formed af...Aluminum silicon titanium master alloys were prepared in the laboratory by electrolysis of silica and titania dissolved in cryolite alumina melts. Alloys containing up to 12 mass% Si and 2.6 mass% Ti were formed after about 90 min of electrolysis at 950℃. The current efficiency for the preparation of the Al Si Ti alloys varied with time, temperature and cathodic current density. It is concluded that this electrolytic method may be an interesting alternative to the direct metal mixing process for formation of Al Si Ti master alloys.展开更多
Low-cost iron-based shape memory alloys(SMAs) show great potential for engineering applications. The developments of new processing techniques have recently enabled the production of nanocrystalline materials with i...Low-cost iron-based shape memory alloys(SMAs) show great potential for engineering applications. The developments of new processing techniques have recently enabled the production of nanocrystalline materials with improved properties. These developments have opened avenues for newer applications for SMAs. The influence of severe plastic deformation induced by the high-speed high-pressure torsion(HSHPT) process on the microstructural evolution of an Fe–Mn–Si–Cr alloy was investigated. Transmission electron microscopic analysis of the alloy revealed the existence of nanoscale grains with an abundance of stacking faults. The high density of dislocations characteristic of severe plastic deformation was not observed in this alloy. X-ray diffraction studies revealed the presence of ε-martensite with an HCP crystal structure and γ-phase with an FCC structure.展开更多
Recently,graphene oxide(GO),MXene,carbon nanotubes(CNTs) have been used for compounding with other materials as anodes and cathodes to achieve excellent electrochemical properties for metal-ion batteries.However,few r...Recently,graphene oxide(GO),MXene,carbon nanotubes(CNTs) have been used for compounding with other materials as anodes and cathodes to achieve excellent electrochemical properties for metal-ion batteries.However,few researches have focused on the differences between the three additives.Herein,silicon,as a typical anode,is selected to integrate with MXene,GO and CNTs in carbon nanofibers(CNFs) and form Si/MXene@CNFs,Si/GO@CNFs and Si/CNTs@CNFs,respectively.Together with the results,it can be realized that these CNFs with a significant improved performance compared with pure Si@CNFs show superiority in different aspects of electrochemical properties.Additionally,the reasons for the superiority are also discussed in this work.The addition of MXene can improve the cycle stability of the electrodes,thereby obtaining a high capacity retention rate,CNTs are favorable for the enhancement of rate performance,and the electrodes reversible capacity can be increased due to the addition of GO.Consequently,the studies on three additives may contribute to the rational design of silicon-based and other anode materials.展开更多
基金National Natural Science FOundation of China! (No. 59974010).
文摘For reducing the core loss of grain oriented silicon steel and improving its aging property, a new method, the LLSA by using Sb as the laser surface alloying element, was investigated, and at proper technique conditions rather good result was obtained.
文摘A mechanism of oxygen transportation in Czochralski growth of silicon crystals under a horizontal magnetic field (HMCZ) is proposed. Oxygen depleted surface melt, driven to the growth interface by the thermal Marangoni flow, determines oxygen concentration in the grown crystals. Systematic study was carried out to investigate effects of growth parameters on oxygen incorporation into crystals.
文摘The P + Sr + Ce compound modification technologies of as-cast Al-21Si-1.5Cu-1.5Ni- 2.5Fe- 0.5Mg alloy were investigated by means of orthogonal test. Orthogonal test results show that 3% (CaH2PO4 + 2CASO4)+ 0.2%Sr + 0.2%Ce is the optimum additive of modification treatment which can fine eutectic and primary silicon also can change the form of rich-iron phase at same time. The needle form of rich-iron phase is Al9FeSi3, which is prored by X-ray diffraction analysis and X-ray energy spectrum analysis. After compound modification treatment, the needle form of rich-iron phase disappeared and the fish bone form of rich-iron and rich-Ce phase that is AlsCeFe emerged. Both at room temperature and at 300℃, the tensile strength of the alloy after the modification treatment with the optimum additive is 30% lager than that of the alloy unmodified. Observed by SEM, the brittle intercrystalline tensile fracture changed into a blended one in which has many dimples.
文摘A high Fe containing aluminum matrix filler metal for hardfacing aluminum silicon alloys has been developed by using iron,nickel,and silicon as the major strengthening elements,and by measuring mechanical properties,room temperature and high temperature wear tests,and microstructural analysis.The filler metal,which contains 3.0%-5.0% Fe and 11.0%-13.0% Si,exhibits an excellent weldability.The as cast and as welded microstructures for the filler metal are of uniformly distribution and its dispersed network of hard phase is enriched with Al Si Fe Ni.The filler metal shows high mechanical properties and wear resistance at both room temperature and high temperatures.The deposited metal has a better resistance to impact wear at 220℃ than that of substrate Al Si Mg Cu piston alloy;at room temperature,the deposited metal has an equivalent resistance to slide wear with lubrication as that of a hyper eutectic aluminum silicon alloy with 27% Si and 1% Ni.
文摘Anovel silicon containing carbon precursor was synthesised by reacting a petroleum pitchfraction and polydimethylsilane. The precursor containing about 26wt% Si was meltspunintofibresand then oxidativelystabilised in airto renderthefibresinfusiblebefore pyrolysisat1200℃underinertatmospheretoproduceC Sialloy( CSA) fibres. Theextentofstabili sation wasfoundto becriticalto the development of mechanicalstrength of thefibres which varied with heattreatmenttemperature, showing a maximum at 1200 ℃when thestrength was 1 4 1 6 GPa. Thesestrengthsareremarkably goodconsideringthelow modulus whichis duetothe quite high failurestrains. Thefibrescanshow excellentresistanceto oxidation if given an initialshortexposureto oxygen athigh temperature duetotheformation of an im perceptiblelayer of silica. CSAfibreshavethe advantagesof both carbon fibresand SiCfi bres,thusextended application areascan beenvisaged .
基金supported by the Industry, Education, and Research Prospective Project of Jiangsu Province, China (No. BY2012191)the Open Research of Jiangsu Key Laboratory of Advanced Metallic Materials (No. AMM201202)
文摘The effects of La addition on the microstructure and tensile properties of B-refmed and Sr-modified A1-1 1Si-1.5Cu-0.3Mg cast- ing alloys were investigated. With a trace addition of La (0.05wt%-0. lwt%), the mutual poisoning effect between B and Sr can be neutral- ized by the formation of LaB6 rather than SrB6. By employing a La/B weight ratio of 2:1, uniform microstructures, which are characterized by well refined ct-A1 grains and adequately modified eutectic Si particles as well as the incorporation of precipitated strengthening intermetal- lics, are obtained and lead to appreciable tensile properties with an ultimate tensile strength of 270 MPa and elongation of 5.8%.
基金the ministry of higher education Malaysia and Universiti Tun Hussein Onn Malaysia for supporting this research under Vot no FRGS1422 and E15501
文摘The effects of Ce on the secondary dendrite arm spacing(SDAS) and mechanical behavior of Al-Si-Cu-Mg alloys were investigated. The reduction of SDAS at different Ce concentrations was evaluated in a directional solidification experiment via computer-aided cooling curve thermal analysis(CA-CCTA). The results showed that 0.1wt%-1.0wt% Ce addition resulted in a rapid solidification time, ?ts, and low solidification temperature, ?T_S, whereas 0.1wt% Ce resulted in a fast solidification time, Δ^(ta-Al), of the α-Al phase. Furthermore, Ce addition refined the SDAS, which was reduced to approximately 36%. The mechanical properties of the alloys with and without Ce were investigated using tensile and hardness tests. The quality index(Q) and ultimate tensile strength of(UTS) Al-Si-Cu-Mg alloys significantly improved with the addition of 0.1wt% Ce. Moreover, the base alloy hardness was improved with increasing Ce concentration.
基金supported by the Research Fund of the State Key Laboratory of Solidification Processing (No.42-QP-009)the Open Fund of the State Key Laboratory of Solidification Processing in NWPU (No.201009)+1 种基金the Fundamental Research Fund of Northwestern Polytechnical University (No.JC200929)the 111 Project of China (No.B08040)
文摘To determine the modifying agents for Al-7Si alloys, microstructure observation and mixing enthalpy analysis using Miedema model for Al-7Si alloy with additions of different rare earth elements were performed, and the effects of rare earth elements on the modifica-tion of eutectic silicon morphology were investigated. The results of mixing enthalpy analysis show that these four rare earth elements, La, Sm, Pr, and Ce, which have the large negative mixing enthalpies with Si, can be selected as modifying agents for eutectic silicon morphology. The element with the largest negative mixing enthalpy is Ce. Furthermore, the microstructures indicate that these four elements can effec-tively modify the eutectic (α)Al-Si crystals in Al-7Si alloy, and the most effective one is also Ce. Differential scanning calorimetry (DSC) results show that the eutectic temperature depressions due to the additions of modifying agents are the important reasons for the modification of eutectic (α)Al-Si crystals.
基金financially supported by the National Basic Research Program of China (No. 2011CB606300)the National Natural Science Foundation of China (No. 5077400)
文摘In this study, a serpentine channel pouring process was used to prepare the semi-solid A1-20%Si alloy slurry and refine primary Si grains in the alloy. The effects of the pouring temperature, number of curves in the serpentine channel, and material of the serpentine channel on the size of primary Si grains in the semi-solid A1-20%Si alloy slurry were investigated. The results showed that the pouting temperature, number of the curves, and material of the channel strongly affected the size and distribution of the primary Si grains. The pouring tempera- ture exerted the strongest effect, followed by the number of the curves and then the material of the channel. Under experimental conditions of a four-curve copper channel and a pouring temperature of 701℃, primary Si grains in the semi-solid A1-20%Si alloy slurry were refined to the greatest extent, and the lath-like grains were changed into granular grains. Moreover, the equivalent grain diameter and the average shape coefficient of primary Si grains in the satisfactory semi-solid A1-20%Si alloy slurry were 24.4 μm and 0.89, respectively. Finally, the re- finement mechanism and distribution rule of primary Si grains in the slurry prepared through the serpentine channel pouring process were analyzed and discussed.
基金supported by the National Natural Science Foundation of China (No.51004010)the Research Fund for the Doctoral Program of Higher Education of China (No.20090006120022)
基金financially supported by the High-Tech Research and Development Program of China(No.SS2013AA031305)the Key Technologies R&D Program of Tianjin(No.12ZCDGGX49100)
基金This work was financially supported by the National Natural Science Foundation of China(Nos.51675158,51535011,and 51675531)the Natural Science Foundation of Hebei Province(No.E2016202325)the Beijing Municipal Natural Science Foundation(No.3172038).
文摘A high content silicon aluminum alloy(Al-25Si-4Cu-1Mg)coating was prepared on a 2A12 aluminum alloy by supersonic plasma spraying.The morphology and microstructure of the coating were observed and analyzed.The hardness,elastic modulus,and bonding strength of the coating were measured.The wear resistance of the coating and 2A12 aluminum alloy was studied by friction and wear test.The results indicated that the coating was compact and the porosity was only 1.5%.The phase of the coating was mainly composed ofα-Al andβ-Si as well as some hard particles(Al9Si,Al3.21Si0.47,and CuAl2).The average microhardness of the coating was HV 242,which was greater than that of 2A12 aluminum alloy(HV 110).The wear resistance of the coating was superior to 2A12 aluminum alloy.The wear mechanism of the 2A12 aluminum alloy was primarily adhesive wear,while that of the coating was primarily abrasive wear.Therefore,it is possible to prepare a high content silicon aluminum alloy coating with good wear resistance on an aluminum alloy by supersonic plasma spraying.
基金supported by the National Natural Science Foundation of China(NSFC,China) under Grant Number of 51405467Chongqing Research of Application Foundation and Advanced Technology(project No.cstc2016jcyj A0016)the Key Program of the Chinese Academy of Sciences(No.KGZD-EW-T0)
文摘The mechanical properties and friction behaviors of CNT/AlSi10Mg composites produced by spark plasma sintering (SPS) were investigated. The results showed that the densities of the sintered composites gradually increased with increasing sintering temperature and that the highest microhardness and compressive strength were achieved in the specimen sintered at 450A degrees C. CNTs dispersed uniformly in the Al-Si10Mg matrix when the addition of CNTs was less than 1.5wt%. However, when the addition of CNTs exceeded 1.5wt%, the aggregation of CNTs was clearly observed. Moreover, the mechanical properties (including the densities, compressive strength, and microhardness) of the composites changed with CNT content and reached a maximum value when the CNT content was 1.5wt%. Meanwhile, the minimum average friction coefficient and wear rate of the CNT/AlSi10Mg composites were obtained with 1.0wt% CNTs.
文摘The synthetical soft magnetic properties were reported for newly-developed nanocrystalline Fe73.5Cu1Nb0.9 Mo2.1Si13.5B9 and Fe73.5Cu1Nb0.5 Mo2.5Si13.5B9 alloys. The levels of high-frequency losses of the new alloys are P3/100k=612 and 670 kWm-3, P2/200k=880 and 973kWm-3, P2/500k=4300 and 4600 kWm-3, P0.5/1000k=860 and 920 kWm-3, respectively. They are significantly lower than those of the superior power Mn-Zn ferrite H7c4. The dependence of core loss on frequency and amplitude flux density has been analyzed. The practical applications of the new alloys to switching mode power supplies with the output power of 1 and 2kW were reported.
基金supported by the National Natural Science Foundation of China(No.51201172)
文摘The corrosion-wear behavior of a nanocrystalline Fe_(88)Si_(12) alloy disc coupled with a Si_3N_4 ball was investigated in acid(pH 3) and alkaline(pH 9) aqueous solutions. The dry wear was also measured for reference. The average friction coefficient of Fe_(88)Si_(12) alloy in the pH 9 solution was approximately 0.2, which was lower than those observed for Fe_(88)Si_(12) alloy in the pH 3 solution and in the case of dry wear. The fluctuation of the friction coefficient of samples subjected to the pH 9 solution also showed similar characteristics. The wear rate in the pH 9 solution slightly increased with increasing applied load. The wear rate was approximately one order of magnitude less than that in the pH 3 solution and was far lower than that in the case of dry wear, especially at high applied load. The wear traces of Fe_(88)Si_(12) alloy under different wear conditions were examined and analyzed by scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy. The results indicated that the tribo-chemical reactions that involve oxidation of the worn surface and hydrolysis of the Si_3N_4 ball in the acid solution were restricted in the pH 9 aqueous solution. Thus, water lubrication can effectively improve the wear resistance of nanocrystalline Fe_(88)Si_(12) alloy in the pH 9 aqueous solution.
文摘A novel wide-band laser cladding system, with high rate of cladding, has been developed in the present work. The system mainly consisted of a 5kW CO2 laser, an automatic powder feeder and a wide-band scanning rotative polygon mirror which can produce a linear or rectangular focused laser beam. Using this system, a Ni-Cr-Si-B alloy powder was cladded on the surface of type 321 austenitic stainless steel in order to improve its wear and corrosion resistance. The pitting corrosion, high temperature oxidation and wear tests were conducted in order to evaluate the properties of the laser cladded layer. The results demonstrated that the cladded layer can significantly improve the adhesive wear and pitting corrosion resistance of the substrate. Moreover, the cladded layer exhibited good oxidation resistance, which is almost the same as that of GMR-235D Ni-based superalloy.
文摘The strength and elongation to fracture of spray deposited Al-Si-Pb alloys were studied as a function of lead content, silicon content, and distance from the centre to periphery of the deposit. It is found that the ultimate tensile strength, proof stress and elongation to fracture decrease, linearly and exponentially, with the increase in lead content and porosity of the deposit, respectively. Both the strengths and elongation to fracture linearly increase with increasing distance from the centre to periphery of the deposit. The ultimate tensile strength and proof stress are higher at a higher silicon content and they have a linear relationship with the hardness of the deposit.
文摘Aluminum silicon titanium master alloys were prepared in the laboratory by electrolysis of silica and titania dissolved in cryolite alumina melts. Alloys containing up to 12 mass% Si and 2.6 mass% Ti were formed after about 90 min of electrolysis at 950℃. The current efficiency for the preparation of the Al Si Ti alloys varied with time, temperature and cathodic current density. It is concluded that this electrolytic method may be an interesting alternative to the direct metal mixing process for formation of Al Si Ti master alloys.
基金supported by Project PN.IIPT-PCCA-2011-3.1-0174,Contract 144/2012
文摘Low-cost iron-based shape memory alloys(SMAs) show great potential for engineering applications. The developments of new processing techniques have recently enabled the production of nanocrystalline materials with improved properties. These developments have opened avenues for newer applications for SMAs. The influence of severe plastic deformation induced by the high-speed high-pressure torsion(HSHPT) process on the microstructural evolution of an Fe–Mn–Si–Cr alloy was investigated. Transmission electron microscopic analysis of the alloy revealed the existence of nanoscale grains with an abundance of stacking faults. The high density of dislocations characteristic of severe plastic deformation was not observed in this alloy. X-ray diffraction studies revealed the presence of ε-martensite with an HCP crystal structure and γ-phase with an FCC structure.
基金financially supported by the National Natural Science Foundation of China(No.51702046)the Open Project of State Key Laboratory of Advanced Special Steel,Shanghai Key Laboratory of Advanced Ferrometallurgy,Shanghai University(SKLASS 2019-2021)+1 种基金the Science and Technology Commission of Shanghai Municipality(No.19DZ2270200)the Program for Professor of Special Appointment(Eastern Scholar)at Shanghai Institutions of Higher Learning,State Key Laboratory for Modification of Chemical Fibers and Polymer Materials,Donghua University。
文摘Recently,graphene oxide(GO),MXene,carbon nanotubes(CNTs) have been used for compounding with other materials as anodes and cathodes to achieve excellent electrochemical properties for metal-ion batteries.However,few researches have focused on the differences between the three additives.Herein,silicon,as a typical anode,is selected to integrate with MXene,GO and CNTs in carbon nanofibers(CNFs) and form Si/MXene@CNFs,Si/GO@CNFs and Si/CNTs@CNFs,respectively.Together with the results,it can be realized that these CNFs with a significant improved performance compared with pure Si@CNFs show superiority in different aspects of electrochemical properties.Additionally,the reasons for the superiority are also discussed in this work.The addition of MXene can improve the cycle stability of the electrodes,thereby obtaining a high capacity retention rate,CNTs are favorable for the enhancement of rate performance,and the electrodes reversible capacity can be increased due to the addition of GO.Consequently,the studies on three additives may contribute to the rational design of silicon-based and other anode materials.