HVOF-sprayed HAp/S53P4 BG composite coatings on an AZ31 alloy for potential applications in temporary implants

Bioactive thermal spray coatings produced via high-velocity oxygen fuel spray(HVOF)from hydroxyapatite(HAp)and bioactive glasses(BG)have the potential to be employed on temporary implants due to the ability of both HAp and BG to dissolve and promote osseointegration,considering that both phases have different reaction and dissolution rates under in-vitro conditions.In the present work,75%wt.HAp-25%wt.S53P4 bioactive glass powders were HVOF-sprayed to obtain HAp/S53P4 BG composite coatings on a bioresorbable AZ31 alloy.The study is focused on exploring the effect of the stand-off distance and fuel/oxygen ratio variation as HVOF parameters to obtain stable structural coatings and to establish their effect on the phases and microstructure produced in those coatings.Different characterization techniques,such as scanning electron microscopy,X-ray diffraction,and Fourier transform infrared spectroscopy,were employed to characterize relevant structural and microstructural properties of the composite coatings.The results showed that thermal gradients during coating deposition must be managed to avoid delamination due to the high temperature achieved(max 550℃)and the differences in coefficients of thermal expansion.It was also found that both spraying distance and oxygen/fuel ratio allowed to keep the hydroxyapatite as the main phase in the coatings.In addition,in-vitro electrochemical studies were performed on the obtained HAp/S53P4 BG composite coatings and compared against the uncoated AZ31 alloy.The results showed a significant decrease in hydrogen evolution(at least 98%)when the bioactive coating was applied on the Mg alloy during evaluation in simulated body fluid(SBF).

Structure and corrosion behavior of FeCoCrNiMo high-entropy alloy coatings prepared by mechanical alloying and plasma spraying

FeCoCrNiMox composite powders were prepared using the mechanical alloying technique and made into high-entropy alloy(HEA)coatings with the face-centered cubic phase using plasma spraying to address the element segregation problem in HEAs and pre-pare uniform HEA coatings.Scanning electron microscopy,transmission electron microscopy,and X-ray diffractometry were employed to characterize these coatings’microstructure and phase composition.The hardness,elastic modulus,and fracture toughness of coatings were tested,and the corrosion resistance was analyzed in simulated seawater.Results show that the hardness of the coating is HV0.1606.15,the modulus of elasticity is 128.42 GPa,and the fracture toughness is 43.98 MPa·m^(1/2).The corrosion potential of the coating in 3.5wt%NaCl solution is-0.49 V,and the corrosion current density is 1.2×10^(−6)A/cm^(2).The electrochemical system comprises three parts:the electrolyte,the adsorption and metallic oxide films produced during immersion,and the FeCoNiCrMo HEA coating.Over in-creasingly long periods,the corrosion reaction rate increases first and then decreases,the corrosion product film comprising metal oxides reaches a dynamic balance between formation and dissolution,and the internal reaction of the coating declines.

Effects of plasma spraying process on microstructure and mechanical properties of Cr_(2)AlC/410 composite coatings

To investigate the influences of Cr_(2)AlC mass fraction and supersonic plasma spraying process on the microstructure and mechanical properties of Cr_(2)AlC reinforced 410 stainless steel composite coatings,the coatings containing different mass fractions of Cr_(2)AlC were prepared and investigated.The composite coating exhibited low porosity and high adhesion strength.The addition of Cr_(2)AlC significantly enhanced the hardness of the composite coatings through particle strengthening.However,when the mass fraction of Cr_(2)AlC was 20%,the aggregation of Cr_(2)AlC resulted in a strong decrease in the coating preparation efficiency,as well as a decline in adhesion strength.In the supersonic plasma spraying process,the Ar flow rate mainly influenced the flight velocity of the particles,while the H_(2) flow rate and the current mainly affected the temperature of the plasma torch.Consequently,all of them influenced the melting degree of particles and the quality of the coating.The lowest porosity and the highest hardness and adhesion strength could be obtained when the Ar flow rate is 125 L/min,the H_(2) flow rate is 25 L/min,and the current is 385 A.

High temperature oxidation behavior of Ti(Al,Si)_3 diffusion coating on γ-TiAl by cold spray

A Ti(Al,Si)3 diffusion coating was prepared on γ-TiAl alloy by cold sprayed Al?20Si alloy coating, followed by a heat-treatment. The isothermal and cyclic oxidation tests were conducted at 900 °C for 1000 h and 120 cycles to check the oxidation resistance of the coating. The microstructure and phase transformation of the coating before and after the oxidation were studied by SEM, XRD and EPMA. The results indicate that the diffusion coating shows good oxidation resistance. The mass gain of the diffusion coating is only a quarter of that of bare alloy. After oxidation, the diffusion coating is degraded into three layers: an inner TiAl2 layer, a two-phase intermediate layer composed of a Ti(Al,Si)3 matrix and Si-rich precipitates, and a porous layer because of the inter-diffusion between the coating and substrate.

Microstructure and properties of Al_2O_3-13%TiO_2 coatings sprayed using nanostructured powders

The microstructure and wear performance of M203-13% TiO2 coatings prepared by plasma spraying of agglom- erated nanoparticle powders were investigated. SEM analysis showed that the as-sprayed Al2O3-TiO2 coatings comprise of two kinds of typical region： fully melted region and unmelted/partially melted nanostructured region, which is different than the conventional coating with lamellar structure. It is shown that the microhardness of the nanostructured coatings was about 15%-30% higher than that of the conventional coating and the wear resistance is significantly improved, especially under a high wear load. The nanostructured coating sprayed at a lower power shows a lower wear resistance than the coatings produced at a higher power, because of the presence of pores and microstructural defects which are detrimental to the fracture toughness of the coatings.

TiC-Fe coatings prepared by flame spray synthesis process

A new process, flame spray synthesis (FSS), has been developed for producing ceramic containing composite coatings. By combining self propagation high temperature synthesis (SHS) and flame spraying, the cermet based material was synthesized and deposited simultaneously. TiC Fe coatings were deposited from commercial ferrotitanium, iron and graphite powders by the flame spraying synthesis process. Microstructure analyses revealed that TiC was synthesized during spraying, and that submicron and round TiC particles were dispersed within an iron matrix. Flame spray synthesized coatings were composed of alternate soft and hard layers, whose hardness were 3.0～6.0 GPa and 11～13 GPa, respectively.

Identifying the optimal HVOF spray parameters to attain minimum porosity and maximum hardness in iron based amorphous metallic coatings

Flow based Erosion e corrosion problems are very common in fluid handling equipments such as propellers, impellers, pumps in warships, submarine. Though there are many coating materials available to combat erosionecorrosion damage in the above components, iron based amorphous coatings are considered to be more effective to combat erosionecorrosion problems. High velocity oxy-fuel(HVOF)spray process is considered to be a better process to coat the iron based amorphous powders. In this investigation, iron based amorphous metallic coating was developed on 316 stainless steel substrate using HVOF spray technique. Empirical relationships were developed to predict the porosity and micro hardness of iron based amorphous coating incorporating HVOF spray parameters such as oxygen flow rate, fuel flow rate, powder feed rate, carrier gas flow rate, and spray distance. Response surface methodology(RSM) was used to identify the optimal HVOF spray parameters to attain coating with minimum porosity and maximum hardness.

Plasma Spray Forming of Nanostructured Composite Coatings

The nanostructure composite coating is obtained via plasma spraying of Al2O3-13 wt pct TiO2 powder. Brittle and hard lamella results from melted nanostructured powder. Ductile nanostructured matrix forms from unmelted nanostructured particles. Through the adjustment of constituent and nanostructure, hardness/strength and toughness/ductility are balanced and overall properties of the structure composite are achieved.

A New Process for Preparing Fine-ceramic-containing Composite Coatings──Flame Spray Synthesis

Flame spray synthesis (FSS), a combination of the flame spray technology and Self-propagation High-temperature Synthesis (SHS) was developed for preparing fine-ceramic-containing composite coatings. It can simplify the preparations of powder to synthesize and deposit the desired materials in one step. The preliminary results obtained from TiC-Fe cermet coatings by FSS process are reported. The peculiar microstructure of the composite coatings, which contains very fine (<1m) and round TiC and alternate TiC-rich (Hv=11€*13GPa) and TiC-poor layers (Hv=3.0 -6.0GPa), is expected to play an important role in their tribological properties.

Deformation Behavior of Nanostructured Ceramic Coatings Deposited by Thermal Plasma Spray

Al2O3-13 wt pet TiO2 coating deposited by direct current plasma spray consists of nanostructured region and micro-lamellae. Bend test shows that the ceramic coating can sustain some deformation without sudden failure. The deformation is achieved through the movement of nano-particles in the nanostructured region under tensile stress.

Electrochemical Corrosion Behavior of Arc Sprayed Zn and Zn15Al Coatings in Simulated Salina Soil and Neutral Meadow Soil Solutions

Arc sprayed Zn and Zn15Al coatings were chosen to protect the metal ends of prestressed high-strength concrete （PHC） pipe piles against corrosion of salina soil in northern china and neutral meadow soil in northeast China. The corrosion behavior of the coated Q235 steel samples in two simulated soil solutions were investigated by potentiodynamic polarization and electrochemical impedance spectroscopy （EIS） methods. The experimental results show that the corrosion of the matrix Q235 steel in both simulated solutions is remarkably inhibited by Zn and Zn15Al coatings. The corrosion products on Zn and Zn15Al are thick, compact, firm and protective. The corrosion current density icorr of both Zn and Zn15Al-coated samples is decreased evidently with corrosion time, and the charge transfer resistance Rct is increased greatly. The corrosion resistance indexes of Zn and Zn15Al in simulated neutral meadow soil solution are more outstanding than those in salina soil. The corrosion resistance of Zn15Al in salina soil is slightly superior to that of Zn. When the sprayed coatings are sealed with epoxy resin, the corrosion resistance of the coatings is further enhanced markedly.

Spray deposition of FeCrNiMn and high carbon steel coatings by thermite reaction

A novel surface cladding technique was developed to prepare the FeCrNiMn alloy and high carbon steel cladding layers,and the microhardness,bonding strength,abrasion wear and corrosion resistance were investigated.The microstructures of the cladding layers were analyzed by using X-ray diffraction(XRD),scanning electron microscopy(SEM),and energy dispersive spectrometry(EDS).The results show that the bonding strength between the substrate and the two cladding layers were(432.6±21)and(438.3±12)MPa,respectively.Vickers hardness values of the two cladding layers were HV418.5and HV329.6,respectively.The corrosion current densities of the two coatings were2.926×10–6and6.858×10–6A/cm2after electrochemical corrosion test in3.5%NaCl solution,and the wear rate were1.78×10–7and1.46×10–6mm3/mN after sliding wear test,respectively.This indicates that a well metallurgical bonding between the coating and the substrate was achieved,the abrasion wear and corrosion resistance of both coatings had been greatly improved compared with the substrate.The novel cladding technology is promising for preparing wear-and-corrosion resistant coatings.

Residual stress evaluations of thermally sprayed coatings by a modified Almen method

Based on the Almen method, the authors have modified this test method so that the results of the simple test can be correlated to the absolute values of residual stress measured by conventional methods such as X-ray diffraction, or mechanical techniques. The technique utilizes changes in the strain of standardized test substrates, which is measured by BHP-700℃ temperature-compensated resistance strain gauges, as an indication of the level of residual stress in the sprayed coatings. Based on the concept that the sprayed coating on the surface of substrate with residual stresses acts a force (N) and bending moment (M) on the test piece, the calculating equation of residual stress in the coatings has been proposed. The results of the test method showed that the technique is potentially reliable and accurate, although deficiencies and many controversies are still exist.

INVESTIGATION ON MICROSTRUCTURE AND TRIBOLOGICAL PROPERITIES OF CORED WIRE ARC SPRAYED Al/Al _2 O_3 COATINGS

Cored wires for electric arc spraying of Al/Al 2 O 3 MMC coatings were developed, with Al 2 O 3 powder as the core material and commercial aluminium strip as the retaining sheath. The bond strength, Al 2 O 3 content, microstructure, micro-hardness and wear resistance of coatings produced by arc spraying of the cored wires were experimentally investigated and were compared with those of pure aluminum coating.

Preparation and performance of a cold gas dynamic sprayed high-aluminum bronze coating

By mixing preheated high-aluminum bronze powders with different amounts of Al_2O_3 powder, a low-pressure cold-sprayed coating was prepared and sprayed onto a Cr12MoV steel substrate. The hardness of the coating and the bonding strength between the coating and the substrate were tested with a HV-1000 microhardness tester and a mechanical universal testing machine. The surface microstructure, cross-section and tensile fracture surface of the coating were observed with a scanning electron microscope(SEM). Correspondingly, the influences of the preheat treatment temperature of the bronze powder and the Al_2O_3 content on the coating performance were investigated. The results indicate that the hardness of bronze powders decreased and the coating deposition rate increased after the preheating treatment of the bronze powder. The Al_2O_3 content in the mixed powders contributed to the deformation of bronze powders during the spraying process. This trend resulted in varied performance of the coating.

Salt spray corrosion test of micro-plasma oxidation ceramic coatings on Ti alloy

Ceramic coatings were prepared on Ti-6Al-4V alloy in NaAlO2 solution by micro-plasma oxidation （MPO）. The salt spray tests of the coated samples and the substrates were carded out in a salt spray test machine. The phase composition and surface morphology of the coatings were investigated by XRD and SEAM. Severe corrosion occurred on the substrate surface, while there were no obvious corrosion phenomena on the coated samples. The coatings were composed of Al2TiO5 and a little α-Al2O3 and mille TiO2, and the salt spray test did not change the composition of the coatings. The weight loss rate of the coatings decreased with increasing MPO time because of the increase in density and thickness of the coatings. The surface morphology of the coatings was influenced by salt spray corrosion test. Among the coated samples, the coating prepared for 2 h has the best corrosion resistance under salt spray test.

Spray coating of polysulfone/poly(ethylene glycol) block polymer on macroporous substrates followed by selective swelling for composite ultrafiltration membranes

Polysulfone(PSF) is extensively used for the production of ultrafiltration(UF) membranes thanks to its high strength,chemical stability,and good processibility.However,PSF is intrinsically hydrophobic,and hydrophilic modification is always required to PSF-based membranes if they are intended to be used in aqueous systems.Facile strategies to prepare hydrophilic PSF membranes are thus highly demanded.Herein we spray coat a PSF-based amphiphilic block polymer onto macroporous substrates followed by selective swelling to prepare flat-sheet PSF UF membranes.The polymer is a triblock polymer containing PSF as the majority middle block tethered with shorter block of polyethylene glycol(PEG) on both ends,that is,PEG-b-PSF-b-PEG.We use the technique of spray coa ting to homogeneously dispense diluted triblock polymer solutions on the top of macroporous supports,instantly resulting in uniform,defect-free polymer coating layers with the thickness down to ~1.2 μm.The bi-layered composite structures are then immerged in ethanol/acetone mixture to generate mesoscale pores in the coating layers following the mechanism of selective swelling-induced pore generation,thus producing composite membranes with the mesoporous triblock polymer coating as the selective layers.This facile strategy is free from additional hydrophilic modification and much smaller dosages of polymers are used compared to conventional casting methods.The pore sizes,porositie s,hydrophilicity,and consequently the separation properties of the membranes can be flexibly tuned by changing the swelling duration and the composition of the swelling bath.This strategy combining spray coating and selective swelling is upscalable for the production of highperformance PSF UF membranes.

The Surface Morphologies and Spectroscopy Analysis of VC Coatings on the Substrate of Cr12MoV Prepared by TD Process after Salt Spray

The normal temperature corrosion of VC coating on the substrate of Cr12MoV prepared by TD process was tested in 5% NaCl aqueous solution, its surface morphologies and corrosion components after salt spray were observed with SEM and EDS, respectively, and the effects of salt spray on micro-structures of VC coating were analyzed. Moreover, the invalidation mechanism of VC coating after salt spray and its effect on substrate material were discussed. The experimental results shown that the uniformity and integrity of VC coating surface are destroyed by salt spray for 120 h, a large number of the pits are produced on the coating surface, and the coating falls off, which speeds corrosion breakage of its substrate; the oxidated film on its surface becomes rougher, broken and discontinuous, and falls off easily, which reduce the ability of resistance salt spray; the failure modes of VC coating after salt spray are expressed with falling off of oxidated film, stress concentration and pore effect and so on, the corrosion breakage of oxidated film is the corrosion result of deoxidization corrosion from oxygen and HCl produced by NaCl and vapor.

Cavitation and electrochemical characteristics of thermal spray coating with sealing material

Steel applied in ocean environment is exposed to corrosion and cavitation and is subject to increasing damages. To prevent this, anti-corrosion thermal spray coating technique is widely used. The low-temperature thermal spray coating was performed with 85%Al-14.5%Zn-0.5%Zr for ship materials and various sealing materials were applied to improve its durability, and the electrochemical behavior and cavitation characteristics were observed. The results show that the sealing improves all the properties of the materials. Hybrid ceramic and fluoro-silicon sealing materials show good electrochemical characteristics, and the fluoro-silieon sealing material shows the best anti-cavitation characteristics.

Effects of F-Si sealer on electrochemical characteristics of 15%Al-85%Zn alloy thermal spray coating

Most hulls of the ships are protected with paintings, sacrificial anode, and impressed current cathodic protection methods against corrosion problems. However, these conventional methods are not very effective because the rudder of ships stern are exposed to very severe corrosive environment such as tides, speeds of ships, cavitations and erosion corrosion. The environmental factors such as cavitation and corrosion will cause damage for materials with the shock wave by the creation and destruction of bubble. To solve these problems, the cavitation and electrochemical experiments are executed for thermal spray coating with Al-Zn alloy wire material. Thereafter, and sealed specimens with F-Si sealer on Al-Zn alloy coated specimen are executed to improve electrochemical and anti-cavitation characteristics in sea water. The application of fluorine silicon sealing after spray coating of 15%Al-85%Zn seems to be appropriate not only in static environment but also in dynamic environment.