Analysis and experimental study on resistance-increasing behavior of composite high efficiency autonomous inflow control device

Bottom water coning is the main reason to reduce the recovery of horizontal bottom water reservoir. By water coning, we mean the oil-water interface changes from a horizontal state to a mound-shaped cone and breaks through to the wellbore. Autonomous inflow control device(AICD) is an important instrument maintain normal production after bottom water coning, however, the resistance increasing ability of the swirl type AICD is insufficient at present, which seriously affects the water control effect. Aiming this problem, this paper designs a multi-stage resistance-increasing and composite type AICD. The separation mechanism of oil-water two phases in this structure, the resistance form of oil-water single phase and the resistance-increasing principle of water phase are analyzed. Establishing the dual-phase multi-stage separation and resistance-increasing model, and verified by measuring the throttling pressure drop and oil-water volume fraction of the AICD, it is found that the composite type AICD has the effect of ICD and AICD at the same time, which can balance the production rate of each well section at the initial stage of production, delay the occurrence of bottom water coning. In the middle and later stages of production, water-blocking can be effectively increased to achieve water control and stable production.After structural sensitivity analysis, the influence law of various structural parameters on the water control performance of composite AICD was obtained. The simulation calculation results show that,compared with the existing swirl type AICD, composite AICD has higher sensitivity to moisture content,the water phase throttling pressure drop is increased by 4.5 times on average. The composite AICD is suitable for the entire stage of horizontal well production.

Chemical simulation teaching system based on virtual reality and gesture interaction

Background Most existing chemical experiment teaching systems lack solid immersive experiences,making it difficult to engage students.To address these challenges,we propose a chemical simulation teaching system based on virtual reality and gesture interaction.Methods The parameters of the models were obtained through actual investigation,whereby Blender and 3DS MAX were used to model and import these parameters into a physics engine.By establishing an interface for the physics engine,gesture interaction hardware,and virtual reality(VR)helmet,a highly realistic chemical experiment environment was created.Using code script logic,particle systems,as well as other systems,chemical phenomena were simulated.Furthermore,we created an online teaching platform using streaming media and databases to address the problems of distance teaching.Results The proposed system was evaluated against two mainstream products in the market.In the experiments,the proposed system outperformed the other products in terms of fidelity and practicality.Conclusions The proposed system which offers realistic simulations and practicability,can help improve the high school chemistry experimental education.

Construction and Practice of First-Class Courses on Virtual Simulation Experimental Teaching of Urban Overpasses

Virtual simulation experiment,as a new way to promote the digital transformation of education,has a broad development prospect and application value.The civil engineering experimental volume and space are huge,it has a long construction period,is highly dangerous,and is difficult to experiment with.In order to solve the contradiction between the traditional theory teaching of civil engineering and the engineering training of students,the construction of virtual simulation experimental teaching courses with a high degree of realism,intuition,and accuracy can be used as a useful supplement and innovation of experimental and practical teaching.This paper takes the virtual simulation experimental teaching course of urban overpasses as an example,introduces the necessity and practicability of the course construction,and describes the experimental principle structure of the course,the simulation scene design,the experimental teaching process,the experimental method,etc.The course has achieved good application results,and it has been recognized as the first-class virtual simulation teaching course of the Chongqing Municipal Government,which provides certain references to the construction of the same type of courses in the civil engineering profession.

Research on the Application of Virtual Simulation Experimental Teaching in the Securities Investment Course

With the rapid development of information technology and the increasing complexity of the financial market,the teaching methods and means of the Securities Investment course in universities are facing new challenges and opportunities.The purpose of this paper is to discuss the application and construction path of virtual simulation experimental teaching in the Securities Investment course.Firstly,it analyses the problems existing in the teaching of traditional securities investment courses,such as the disconnection between theory and practice and the single teaching mode.In order to solve these problems,this paper puts forward the necessity of introducing virtual simulation experimental teaching and details the specific application path of virtual simulation experimental teaching in the Securities Investment course.

Experimental and Simulation Analysis of Two-Tone and Three-Tone Photodetector Linearity Characterizing Systems

Two measurement techniques are investigated to characterize photodetector linearity. A model for the two-tone and three-tone photodetector systems is developed to thoroughly investigate the influences of setup components on the measurement results. We demonstrate that small bias shifts from the quadrature point of the modulator will induce deviation into measurement results of the two-tone system, and the simulation results correspond well to experimental and calculation results.

Experimental study on the 350 msw simulated heliox saturation-370 msw excursion diving

-The chief purpose of the research was to understand the physiological function change regularity, performance and adaptability of the human body living and working under high pressure for prolonged time.In January 1989, 4 naval divers entered the habital of NMRI's 500 msw saturation diving system after a series of adaptive diving training. The breathing mixture was helium-oxygen. After 55 h compression (including intermediate stages) the 350 msw depth was reached, where the divers lived and worked for 72 h 10 min. No sign of discomfort or significant HPNS was found in the 4 divers.The second and third day of the saturation exposure, the divers carried out 370 msw dry and wet chamber excursion diving 2 man-time each, the divers effectively carried out operational work under water, the total excursion time was 1 h each excursion dive.Saturation decompression started after 3-day storage exposure, the divers were gradually brought toward the surface 25 msw a day on the average by employing the linear steady rate of decompression. During decompression, no case of DCS occurred. Immediate post-dive medical check-ups shows that they were physically normal.More than 120 biomedical indices were monitored and measured on the divers at different period of the experiment. The organisms showed a good adaptability and certain operating capability, and both the compression and decompression profiles were proved to be satisfactory.The detailed experimental data obtained provided sound scientific basis for the practical application of future great depth open sea saturation diving.

A novel procedure for identifying a hybrid QTL-allele system for hybrid-vigor improvement, with a case study in soybean(Glycine max)yield

“Breeding by design” for pure lines may be achieved by construction of an additive QTL-allele matrix in a germplasm panel or breeding population, but this option is not available for hybrids, where both additive and dominance QTL-allele matrices must be constructed. In this study, a hybrid-QTL identification approach, designated PLSRGA, using partial least squares regression(PLSR) for model fitting integrated with a genetic algorithm(GA) for variable selection based on a multi-locus, multi-allele model is described for additive and dominance QTL-allele detection in a diallel hybrid population(DHP). The PLSRGA was shown by simulation experiments to be superior to single-marker analysis and was then used for QTL-allele identification in a soybean DPH yield experiment with eight parents. Twenty-eight main-effect QTL with 138 alleles and nine QTL × environment QTL with 46 alleles were identified, with respective contributions of 61.8% and 23.5% of phenotypic variation. Main-effect additive and dominance QTL-allele matrices were established as a compact form of the DHP genetic structure. The mechanism of heterosis superior-to-parents(or superior-to-parents heterosis, SPH) was explored and might be explained by a complementary locus-set composed of OD+(showing positive over-dominance, most often), PD+(showing positive partial-to-complete dominance, less often) and HA+(showing positive homozygous additivity, occasionally) loci, depending on the parental materials. Any locus-type, whether OD+, PD + and HA+, could be the best genotype of a locus. All hybrids showed various numbers of better or best genotypes at many but not necessarily all loci, indicating further SPH improvement. Based on the additive/dominance QTL-allele matrices, the best hybrid genotype was predicted, and a hybrid improvement approach is suggested. PLSRGA is powerful for hybrid QTL-allele detection and cross-SPH improvement.

Underconstrained Cable-Driven Parallel Suspension System of Virtual Flight Test Model in Wind Tunnel

An underconstrained cable-driven parallel robot(CDPR)suspension system was designed for a virtual flight testing(VFT)model.This mechanism includes two identical upper and lower kinematic chains,each of which comprises a cylindrical pair,rotating pair,and cable parallelogram.The model is pulled via two cables at the top and bottom and fixed by a yaw turntable,which can realize free coupling and decoupling with three rotational degrees of freedom of the model.First,the underconstrained CDPR suspension system of the VFT model was designed according to the mechanics theory,the degrees of freedom were verified,and the support platform was optimized to realize the coincidence between the model’s center of mass and the rotation center of the mechanism during the motion to ensure the stability of the support system.Finally,kinematic and dynamical modeling of the underconstrained CDPR suspension system was conducted;the system stiffness and stability criteria were deduced.Thus,the modeling of an underconstrained,reconfigurable,passively driven CDPR was understood comprehensively.Furthermore,dynamic simulations and experiments were used to verify that the proposed system meets the support requirements of the wind tunnel-based VFT model.This study serves as the foundation for subsequent wind tunnel test research on identifying the aerodynamic parameters of aircraft models,and also provides new avenues for the development of novel support methods for thewind tunnel testmodel.

Experiment Combined with Picture Archiving and Communication System in the Practical Teaching of Medical Imaging

Objective:To explore the application effect of virtual simulation experiment combined with picture archiving and communication system(PACS)in medical imaging practical teaching.Methods:97 students from the medical imaging class of 2022 were divided into two groups;the control group(n=48)was taught by the traditional teaching method,whereas the research group was taught by virtual simulation experiment combined with PACS(n=49).The teaching achievements and teaching effects of the two groups were compared to define the advantages of the two teaching modes.Results:Initially,there were no significant differences in the basic theory,image analysis,report writing,and differential diagnosis scores between the two groups of students(P>0.05);however,after 16 weeks of teaching,the scores of the research group were better than those of the control group(P<0.05);the pass rate of students in the study group(93.88%)was higher than that in the control group(81.25%);the scores of students in the research group in terms of clinical inquiry skills,X-ray/computed tomography/magnetic resonance imaging(X-ray/CT/MRI)operation skills,and doctor-patient communication skills were significantly higher than those in the control group(P<0.05).Conclusion:In medical imaging practical teaching,the application of virtual simulation experiment combined with PACS can effectively address several problems in the traditional teaching mode,including the single teaching method,the single teaching content,and the lack of innovation,and,at the same time,improve students’basic theoretical knowledge,X-ray/CT/MRI operation skills,consultation skills,and doctor-patient communication skills,thereby effectively improving the teaching quality and learning effect.

Formation mechanism of fault accommodation zones under combined stress in graben basin:Implications from geomechanical modeling

A fault accommodation zone is a type of structure that is defined as regulating displacement and strain between faults structure.Increasing numbers of fault accommodation zones are being identified in graben basins,indicating the potential exploration target and petroleum accumulation areas.This study aims to analyze the formation mechanism and development of fault accommodation zones under combined stress by a numerical simulation method considering geomechanical modeling.Using three-dimensional(3-D)seismic interpretation and fractal dimension method,exampled with the Dongxin fault zone,the fault activity and fault combination pattern were conducted to quantitatively characterize the activity difference in fault accommodation zones.Combined with mechanical experiment test,a geomehcanical model was established for fault accommodation zones in a graben basin.Integrating the paleostress numerical simulations and structural physical simulation experiment,the developmental characteristics and genetic mechanism of fault accommodation zones were summarized.Influenced by multi movements and combined stresses,three significant tectonic evolution stages of the Dongxing Fault Zone(DXFZ)were distinguished:During the E_(s)^(3)sedimentary period,the large difference in the stress,strain,and rupture distribution in various faults were significant,and this stage was the key generation period for the prototype of the DXFZ,including the FAZ between large-scale faults.During the E_(s)^(2)sedimentary period,the EW-trending symmetric with opposite dipping normal faults and the NE-SW trending faults with large scale were furtherly developed.The junction area of two secondary normal faults were prone to be ruptured,performing significant period for inheriting and developing characteristics of fault accommodation zones.During the Es1 sedimentary period,the high-order faults in the DXFZ exhibited the obvious fault depressions and strike-slip activity,and the fault accommodation zones were furtherly inherited and developed.This stage was the molded and formative period of the FAZ,the low-order faults,and the depression in the DXFZ.

Failure characteristics and fracture mechanism of overburden rock induced by mining:A case study in China

This study employs similar simulation testing and discrete element simulation coupling to analyze the failure and deformation processes of a model coal seam's roof.The caving area of the overburden rock is divided into three zones:the delamination fracture zone,broken fracture zone,and compaction zone.The caving and fracture zones'heights are approximately 110 m above the coal seam,with a maximum subsidence of 11 m.The delamination fracture zone's porosity range is between 0.2 and 0.3,while the remainder of the roof predominantly exhibits a porosity of less than 0.1.In addition,the numerical model's stress analysis revealed that the overburden rock's displacement zone forms an'arch-beam'structure starting from 160 m,with the maximum and minimum stress values decreasing as the distance of advancement increases.In the stress beam interval of the overburden rock,the maximum value changes periodically as the advancement distance increases.Based on a comparative analysis between observable data from on-site work and numerical simulation results,the stress data from the numerical simulation are essentially consistent with the actual results detected on-site,indicating the validity of the numerical simulation results.

Evaluation of the Shallow Gas Hydrate Production Based on the Radial Drilling-Heat Injection-Back Fill Method

It has been evidenced that shallow gas hydrate resources are abundant in deep oceans worldwide.Their geological back-ground,occurrence,and other characteristics differ significantly from deep-seated hydrates.Because of the high risk of well construction and low production efficiency,they are difficult to be recovered by using conventional oil production methods.As a result,this paper proposes an alternative design based on a combination of radial drilling,heat injection,and backfilling methods.Multi-branch holes are used to penetrate shallow gas hydrate reservoirs to expand the depressurization area,and heat injection is utilized as a supplement to improve gas production.Geotechnical information collected from an investigation site close to the offshore production well in the South China Sea is used to assess the essential components of this plan,including well construction stability and gas production behavior.It demonstrates that the hydraulic fracturing of the 60mbsf overburden layer can be prevented by regulating the drilling fluid densities.However,the traditional well structure is unstable,and the suction anchor is advised for better mechanical performance.The gas produc-tion rate can be significantly increased by combining hot water injection and depressurization methods.Additionally,the suitable produc-tion equipment already in use is discussed.

An experimental study of fracture initiation mechanisms during hydraulic fracturing

The mechanism of fracture initiation is the basic issue for hydraulic fracture technology. Because of the huge differences in fracture initiation mechanisms for different reservoirs,some successful fracturing techniques applied to porosity reservoirs are ineffectual for fractured reservoirs.Laboratory tests using a process simulation device were performed to confirm the characteristics of fracture initiation and propagation in different reservoirs.The influences of crustal stress field,confining pressure,and natural fractures on the fracture initiation and propagation are discussed.Experimental results demonstrate that stress concentration around the hole would significantly increase the fracture pressure of the rock.At the same time,natural fractures in the borehole wall would eliminate the stress concentration,which leads to a decrease in the fracture initiation pressure.

Experimental Research of Reinforced Concrete Buildings Struck by Debris Flow in Mountain Areas of Western China

It＇s very important to simulate impact load of debris flow effectively and to investigate dynamic response of architectures under dynamic impact of debris flow, which are necessary to design disaster mitigation construction. Firstly, reinforced concrete domestic architectures in mountain areas of western China had been chosen as main architecture style. The bearing load style and the destructed shape of reinforced flamed construction impacted by discontinuous viscous debris flow were studied systematically. Secondly, Jiangjia Ravine debris flow valley in Yunnan Province, China had been chosen as research region. Utilizing based data from fieldwork and practical survey, the authors simulated and calculated theoretically impact force of discontinuous viscous debris flow. Thirdly, an impact data collecting system （IMHE IDCS） was designed and developed to fulfill designed simulation experiments. Finally, a series of impact test of researched structure models had been fulfilled. During experiment, the destructed shape and course of models were observed and the dynamic displacement data and main natural frequency data of models were collected and analyzed.

Biomineralization of Uranium: A Simulated Experiment and Its Significance

A simulated experimental reduction of and the synthesis of uraninite by a sulfate-reducing bacteria, Desulfovibrio desulfuricans DSM 642, are first reported. The simulated physicochemical experimental conditions were: 35°C, pH=7.0-7.4, corresponding to the environments of formation of the sandstone-hosted interlayer oxidation-zone type uranium deposits in Xinjiang, NW China. Uraninite was formed on the surface of the host bacteria after a one-week's incubation. Therefore, sulfate-reducing bacteria, which existed extensively in Jurassic sandstone-producing environments, might have participated in the biomineralization of this uranium deposit. There is an important difference in the order- disorder of the crystalline structure between the uraninite produced by Desulfovibrio desulfuricans and naturally occurring uraninite. Long time and slow precipitation and growth of uraninite in the geological environment might have resulted in larger uraninite crystals, with uraninite nanocrystals arranged in order, whereas the experimentally produced uraninite is composed of unordered uraninite nanocrystals which, in contrast, result from the short time span of formation and rapid precipitation and growth of uraninite. The discovery has important implications for understanding genetic significance in mineralogy, and also indicates that in-situ bioremediation of U-contaminated environments and use of biotechnology in the treatment of radioactive liquid waste is being contemplated.

Experimental study on the mechanisms of fault reactivation and coal bumps induced by mining

Experiments simulating the effect of coal mine stopping through a fault zone were designed based on a working face of the Qianqiu coal mine in Yima, China. Through simulation of the physical process of fault reactivation and coal bumps, the displacement of the surrounding strata and evolution characteristics of fault stress under the effect of mining were studied. The mechanism of fault reactivation induced by coal mining was analyzed. The results show that shortly before fault reactiva- tion, the normal stress and shear stress increased rapidly and the risk of a fault slip occurring was also increased. The fault reac- tivation, caused by the mining activity, occurred when the working face was 25-35 m from the fault along the hanging wall. The influence of mining increased the possibility of fault reactivation, while the local failure of the bearing capacity of the working face was the direct cause of the fault slip. Our results indicate that the influence of fault slip on the coal of the working face had a transient impact and acted as a loading-unloading function.

Effect of Methane Gas on Acoustic Characteristics of Hydrate-Bearing Sediment–Model Analysis and Experimental Verification

Gas leakage is an important consideration in natural systems that experience gas hydrate accumulation.A number of velocity models have been created to study hydrate-bearing sediments,including the BGTL theory,the weighted equation,the Wood equation,the K-T equation,and the effective medium theory.In previous work,we regarded water as the pore fluid,which meant its density and bulk modulus values were those of water.This approach ignores the presence of gas,which results in a biased calculation of the pore fluid's bulk modulus and density.To take into account the effect of gas on the elastic wave velocity,it is necessary to recalculate the bulk modulus and density of an equivalent medium.Thus,a high-pressure reactor device for simulating leakage systems was developed to establish the relationship between wave velocity and hydrate saturation in methane-flux mode.A comparison of the values calculated by the velocity model with the experimental data obtained in this study indicates that the effective medium theory(EMT,which considers gas effects)is more applicable than other models.For hydrate saturations of 10%–30%,the result ranges between EMT-B(homogenous gas distribution)and EMT-B(patchy gas distribution).For hydrate saturations of 30%–60%,the results are similar to those of the EMT-B(homogenous gas distribution)mode,whereas hydrate saturations of 60%–70%yield results similar to those of the EMT-A mode.For hydrate saturations greater than 80%,the experimental results are similar to those of the EMT-B mode.These results have significance for hydrate exploitation in the South China Sea.

Numerical and experimental analysis of quenching process for cam manufacturing

In order to obtain satisfactory mechanical properties for the cam used in high-power ship diesel engines, a new quenching technology was proposed by designing a two-stage quenching process with an alkaline bath as the quenching medium. To demonstrate the effectiveness of the proposed new quenching technology, both numerical analysis and experimental study were performed. The new quenching technology was analyzed using finite element method. The combined effects of the temperature, stress and microstructure fields were investigated considering nonlinear material properties. Finally, an experimental study was performed to verify the effectiveness of the proposed new quenching technology. The numerical results show that internal stress is affected by both thermal stress and transformation stress. In addition, the direction of the internal stress is changed several times due to thermal interaction and microstructure evolution during the quenching process. The experimental results show that the proposed new quenching technology significantly improves the mechanical properties and microstructures of the cam. The tensile strength, the impact resistance and the hardness value of the cam by the proposed new quenching technology are improved by 4.3%, 8.9% and 3.5% compared with those by the traditional quenching technology. Moreover, the residual stress and cam shape deformation are reduced by 40.0% and 48.9% respectively for the cam manufactured by the new quenching technology.

Study of Thermodynamics and Kinetics of CH_4-CaSO_4 and H_2S-Fe_2O_3 Systems

The destruction of hydrocarbon in deep carbonate diagenetic environment is one of problems on the formation of oil and gas. Organic-inorganic reactions in the process of TSR(Thermochemical Sulfate Reduction) are the main reason to make disappearance of the hydrocarbons. The work in this field has often been the subject of much research work in recent years. In this paper, the thermodynamics of CH4-CaSO4 and H2S-Fe2O3 systems is discussed to investigate the possibility of reactions. It is found that these two reactions can proceed spontaneously.Increasing temperature is favorite for CH4-CaSO4 system but disfavorite for H2S-Fe2O3 system. Thermal simulation experiments were carried out using autoclave at high temperature and high pressure. The properties of the products were characterized by microcoulometry, FT-IR and XRD methods. On the basis of the experimental data, a reaction kinetic model is developed and kinetic parameters are determined.

Observation system simulation experiments using an ensemble-based method in the northeastern South China Sea

An ensemble-based method for the observation system simulation experiment(OSSE)is employed to design optimal observation stations and assess the present observation stations in the northeastern South China Sea(SCS).We employed the 20-year(1992-2012)sea surface height(SSH)data to design an array to monitor the intraseasonal to interannual variability.The results show that the most key region was found located at the northwest of Luzon Island(LI)where the energetic Luzon cyclonic gyre(LCG)occurs;other key regions include the edge of the LCG,the northwest of the Luzon Strait(LS),and the southwest of Taiwan,China.By contrast,we found that the present observation stations might oversample at the northwest of the LS and undersample at the northwest of LI.In addition,the optimal stations perform better in a larger area than the present stations.In vertical direction,the key layer is located within the upper 200-m depth,of which the surface and subsurface layers are most valuable to the observing system.