A single-chip UHF RFID reader transceiver IC has been implemented in 0.18 μm SiGe BiCMOS technology. The chip includes all transceiver blocks as RX/TX RF front-end, RX/TX analog baseband, frequency synthesizer and I2...A single-chip UHF RFID reader transceiver IC has been implemented in 0.18 μm SiGe BiCMOS technology. The chip includes all transceiver blocks as RX/TX RF front-end, RX/TX analog baseband, frequency synthesizer and I2C with fully-compliant China 800/900 MHz RFID draft, ISO/IEC 18000-6C protocol and ETSI 302 208-1 local regulation. The normal mode receiver in the presence of -3 dBm self-jammer achieves -75 dBm 1% PER sensitivity. The linear class-A PA integrated in transmitter has 25 dBm OP1 dB output power for CW. The fully-integrated fractional-N fre-quency synthesizer is designed based on MASH 1-1-1 sigma-delta modulator and 1.8 GHz fundamental frequency LC-VCO for lower in-band and out-of-band phase noise. The measured phase noise is up to -106 dBc/Hz@200 kHz and -131 dBc/Hz@1 MHz offset from center frequency and the integrated RMS jitter from 10 kHz to 10 MHz is less than 1.6 pS. The chip dissipates 330 mA from 3.3 V power supply when transmitting 22.4 dBm CW signal and the PAE of linear PA is up to 26%. The chip die area is 16.8 mm2.展开更多
This paper describes the innovation schemes of the interface of a CNC machine which cannot communicate with a computer by a Direct Numerical Control(DNC)interface and the functions of a DNC interface system.One archit...This paper describes the innovation schemes of the interface of a CNC machine which cannot communicate with a computer by a Direct Numerical Control(DNC)interface and the functions of a DNC interface system.One architecture of hardware and software of a practi- cal single-chip computer based on DNC interface system developed by the authors is given. Without any change of the original hardware and software,this DNC interface system has been used to innovate the CNC machine's interface to implement the direct communication between a computer and a CNC machine and to achieve no tape transmission of a part program and ma- chine parameters.It has been demonstrated that this DNC interface system has certain practical values in improving the reliability,efficiency and production management of CNC/NC machine.展开更多
Through analyzing the principle of spindle drive of winding mechanism for high speed spinning machine,the article not only describes a kind of mode of spindle drive for take-up motion on the basis of control method of...Through analyzing the principle of spindle drive of winding mechanism for high speed spinning machine,the article not only describes a kind of mode of spindle drive for take-up motion on the basis of control method of constant velocity winding, but also introduces the design technique of software and hardware for the control system of mechatronics of spindle drive mode for take- up motion on the basis of constant velocity winding for high speed spinning machine with single-chip microcomputer. The mathematical model to describe the spindle rotating speed is established. It is an important technology for high speed spinning machine and provides a feasible application way.展开更多
Through the investigation on traditional arc stud welding process, a new welding gun and its control system were developed in this paper. The stepping arc stud welding gun was mainly made by a stepping motor as actuat...Through the investigation on traditional arc stud welding process, a new welding gun and its control system were developed in this paper. The stepping arc stud welding gun was mainly made by a stepping motor as actuating unit and a screw-driven device as moving unit. A control system with a MCS-51 single-chip microcomputer as main control component was used to realize the new stud welding procedure. This new welding process with stepping stud welding gun is named as stepping arc stud welding. In the new welding process, the stud action can be looked as constituted by some micro steps. The setting and adjusting of the stepping arc welding gun behavior parameters are accomplished independently. It is indicated from the results of process tests and bending test that the stepping arc stud welding process is practicable.展开更多
In an optoelectronic 2-D programmable neural network system, optical data need to be transferred and feedback with high speed. This paper presents the design and implementation of the interface circuit and its software.
Single-chip multiprocessor (CMP) combined with the fault-loleranl(FT)techniques offers an ideal architecture to achieve high availability on the basis of sustaining highcomputing performance FT design of a single-chip...Single-chip multiprocessor (CMP) combined with the fault-loleranl(FT)techniques offers an ideal architecture to achieve high availability on the basis of sustaining highcomputing performance FT design of a single-chip multiprocessor is described, including thetechniques from hard-wart redundancy to software support and firmware strategy. The design aims atmasking the influences of errors and automatically correcting the system states.展开更多
This paper uses CT to gain the energy directly from the high-voltage transmission line, to address the problem of power supply for monitoring system in high voltage side of transmission line. The draw-out power coil c...This paper uses CT to gain the energy directly from the high-voltage transmission line, to address the problem of power supply for monitoring system in high voltage side of transmission line. The draw-out power coil can induce voltage from the transmission line, using single-chip microcomputer to analog and output PMW wave to control the charging module, provides a stable 3.4 V DC voltage to the load, and solve the problem of easy saturating of core. The power supply based on this kind of draw-out power coil has undergone the overall testing, and it is verified-showing that it can properly work in a non-saturated status within the current range of 50 - 1000 A, and provide a stable output. The equipment also design protection circuit to improve the reliability to avid the impacts of the impulse current or short-circuit current. It effectively solves the problem of power supply for On-line Monitoring System of Transmission.展开更多
A Smart resistance thermometer sensor is designed to overcome the shortages of the traditional ones, and Con-form to the world development trend of the sensor market.According to the constitutions of this Smart sensor...A Smart resistance thermometer sensor is designed to overcome the shortages of the traditional ones, and Con-form to the world development trend of the sensor market.According to the constitutions of this Smart sensor and its application coverage,those parts with good -application and low-cost were chosen to constitute this sensor on the basis of full consideration of the linkage among every part.The whole testing system were controlled and processed by C8051F350 single-chip,it could measure precise temperature by PT100 resistance thermometer and circumstance temperature for temperature compensating automatically and simultane-ously,it also could amplify signals to convert analog signals to digital ones,and display results automatically by analysing and processing information.Furthermore,it could auto-compensate self-check,and spot communicate.展开更多
In view of domestic scientific and technological achievements at present,real-time control circuit for greenhouse temperature and light intensity has been designed in line with the principle of cost saving and easy co...In view of domestic scientific and technological achievements at present,real-time control circuit for greenhouse temperature and light intensity has been designed in line with the principle of cost saving and easy control.With advanced temperature sensor and light sensor applied to measure the temperature and light intensity,an execution unit is controlled by single-chip microcomputer(SCM)to regulate the temperature and light intensity,creating a hardware design scheme and software design idea.In case of high temperature and high light intensity in greenhouse,the sunshade net will be put down and the blower will be started automatically;in case of low temperature and light intensity,the sunshade net will be folded up and the heating valve will be turned up automatically.In this way,the temperature and light intensity in greenhouse will be controlled within the designed range.展开更多
Mainly introduces intelligent classification trash can be dedicated to solving indoor household garbage classification.The trash can is based on AT89S52 single-chip microcomputer as the main control chip.The single-ch...Mainly introduces intelligent classification trash can be dedicated to solving indoor household garbage classification.The trash can is based on AT89S52 single-chip microcomputer as the main control chip.The single-chip microcomputer realizes the intelligent classification of garbage by controlling the voice module,mechanical drive module,and infrared detection module.The use of voice control technology and infrared detection technology makes the trash can have voice control and overflow alarm functions.The design has the advantages of simple and intelligent operation,simple structure,stable performance,low investment,etc.,which can further effectively isolate people and garbage,reduce human infection with bacteria,and is a feasible solution for classification at the source of garbage.展开更多
A low power dissipation control system for continuous cyclic peritoneal dialysis (CCPD) cycler and its characteristics are reported. Combined withhemodialysis and renal transplantation, peritoneal dialysis is used mai...A low power dissipation control system for continuous cyclic peritoneal dialysis (CCPD) cycler and its characteristics are reported. Combined withhemodialysis and renal transplantation, peritoneal dialysis is used mainly for thetreatment of renal failure. CCPD has been developed during 1980's. It provided automatic dialysis procedures during the night to avoid interruptions in patients'dailyroutine. Furthermore,there is a remarkable decrease in peritonitis occurance usingCCPD. The control system is a critical part for CCPD cycler. The system is approvedto be reliable and flexible in practical experiments. When AC power failure,the system can still ensure the completion of dialysis.展开更多
objective: To introduce the development of a portable multi-parameter monitoring system. Methods: Using signal detecting and data processing techniques, this monitor with a graphic liquid crystal display (LCD) and a s...objective: To introduce the development of a portable multi-parameter monitoring system. Methods: Using signal detecting and data processing techniques, this monitor with a graphic liquid crystal display (LCD) and a single-chip microprocessor 8Xc196Kc can dynamically measure electrocardiogram(ECG), breath wave, blood pressure (BP), breath frequency (BF), heart rate (HR) and body temperature (BT) in real-time. Results: This monitor can dynamically display the ECG, breath wave and other parameters in real time. It can also provide a 24h trend graph for each measured parameter and exchange data, through the serial communication interface (RS232), with the PC or hand-held PC (HPC). Conclusions: This portable monitoring system has a man-machine interface friendly. It is capable of performing continuous monitoring and also used as terminal of a central monitoring system or a tele-monitoring system.展开更多
This paper presents a single-chip 3D electric field microsensor, in which a sensing element is set at the center to detect the Z-axis component of an electrostatic field. Two pairs of sensing elements with the same st...This paper presents a single-chip 3D electric field microsensor, in which a sensing element is set at the center to detect the Z-axis component of an electrostatic field. Two pairs of sensing elements with the same structure are arranged in a cross-like configuration to measure the X- and Y-axis electrostatic field components. An in-plane rotary mechanism is used in the microsensor to detect the X-, Y-, and Z-axis electrostatic field components simultaneously. The proposed microsensor is compact and presents high integration. The microsensor is fabricated through a MetalMUMPS process. Experimental results show that in the range of 0-50 kV/m, the linearity errors of the microsensor are within 5.5%, and the total measure- ment errors of the three electrostatic field components are less than 14.04%.展开更多
The problem of digital controlling of high frequency microplasma arc welding machine has been solved through Fujitsu 16-bits single-chip processor used.Digital welding power sources and their control systems,digital s...The problem of digital controlling of high frequency microplasma arc welding machine has been solved through Fujitsu 16-bits single-chip processor used.Digital welding power sources and their control systems,digital sequential control system,and digital man-machine interaction system were included in digital microplasma arc welding machine studied.Principles,which is about digital sequential control system,digital man-machine interaction system,digital controller and its interface,and controlling software program,were analyzed.It has been showed that full digitalization of high frequency microplasma arc welding machine was fulfilled,minimum welding current of the machine is 0.05A,and arc is stable and can been started unfailingly.展开更多
Nowadays, we are heading towards integrating hundreds to thousands of cores on a single chip. However, traditional system software and middleware are not well suited to manage and provide services at such large scale....Nowadays, we are heading towards integrating hundreds to thousands of cores on a single chip. However, traditional system software and middleware are not well suited to manage and provide services at such large scale. To improve the scalability and adaptability of operating system and middleware services on future many-core platform, we propose the pinned OS/services. By porting each OS and runtime system (middleware) service to a separate core (special hardware acceleration), we expect to achieve maximal performance gain and energy efficiency in many-core environments. As a case study, we target on XML (Extensible Markup Language), the commonly used data transfer/store standard in the world. We have successfully implemented and evaluated the design of porting XML parsing service onto Intel 48-core Single-Chip Cloud Computer (SCC) platform. The results show that it can provide considerable energy saving. However, we also identified heavy performance penalties introduced from memory side, making the parsing service bloated. Hence, as a further step, we propose the memory-side hardware accelerator for XML parsing. With specified hardware design, we can further enhance the performance gain and energy efficiency, where the performance can be improved by 20% with 12.27% energy reduction.展开更多
Working principles of silicon double P-N junction color sensor are introduced and a color measurement system to distinguish tooth color difference is designed in this paper.This system consists of silicon double P-N j...Working principles of silicon double P-N junction color sensor are introduced and a color measurement system to distinguish tooth color difference is designed in this paper.This system consists of silicon double P-N junction,a small optical fiber probe,signal process circuit and an MSP430FG439 single-chip system.Small in size,this system can measure different parts of the tooth in a fast and convenient way with high-accuracy.Thus,this system will be very promising in building prosthodontics and tooth fabrication.展开更多
文摘A single-chip UHF RFID reader transceiver IC has been implemented in 0.18 μm SiGe BiCMOS technology. The chip includes all transceiver blocks as RX/TX RF front-end, RX/TX analog baseband, frequency synthesizer and I2C with fully-compliant China 800/900 MHz RFID draft, ISO/IEC 18000-6C protocol and ETSI 302 208-1 local regulation. The normal mode receiver in the presence of -3 dBm self-jammer achieves -75 dBm 1% PER sensitivity. The linear class-A PA integrated in transmitter has 25 dBm OP1 dB output power for CW. The fully-integrated fractional-N fre-quency synthesizer is designed based on MASH 1-1-1 sigma-delta modulator and 1.8 GHz fundamental frequency LC-VCO for lower in-band and out-of-band phase noise. The measured phase noise is up to -106 dBc/Hz@200 kHz and -131 dBc/Hz@1 MHz offset from center frequency and the integrated RMS jitter from 10 kHz to 10 MHz is less than 1.6 pS. The chip dissipates 330 mA from 3.3 V power supply when transmitting 22.4 dBm CW signal and the PAE of linear PA is up to 26%. The chip die area is 16.8 mm2.
文摘This paper describes the innovation schemes of the interface of a CNC machine which cannot communicate with a computer by a Direct Numerical Control(DNC)interface and the functions of a DNC interface system.One architecture of hardware and software of a practi- cal single-chip computer based on DNC interface system developed by the authors is given. Without any change of the original hardware and software,this DNC interface system has been used to innovate the CNC machine's interface to implement the direct communication between a computer and a CNC machine and to achieve no tape transmission of a part program and ma- chine parameters.It has been demonstrated that this DNC interface system has certain practical values in improving the reliability,efficiency and production management of CNC/NC machine.
文摘Through analyzing the principle of spindle drive of winding mechanism for high speed spinning machine,the article not only describes a kind of mode of spindle drive for take-up motion on the basis of control method of constant velocity winding, but also introduces the design technique of software and hardware for the control system of mechatronics of spindle drive mode for take- up motion on the basis of constant velocity winding for high speed spinning machine with single-chip microcomputer. The mathematical model to describe the spindle rotating speed is established. It is an important technology for high speed spinning machine and provides a feasible application way.
文摘Through the investigation on traditional arc stud welding process, a new welding gun and its control system were developed in this paper. The stepping arc stud welding gun was mainly made by a stepping motor as actuating unit and a screw-driven device as moving unit. A control system with a MCS-51 single-chip microcomputer as main control component was used to realize the new stud welding procedure. This new welding process with stepping stud welding gun is named as stepping arc stud welding. In the new welding process, the stud action can be looked as constituted by some micro steps. The setting and adjusting of the stepping arc welding gun behavior parameters are accomplished independently. It is indicated from the results of process tests and bending test that the stepping arc stud welding process is practicable.
基金Supported by the National High Technology programme of Chinathe Climbing Programme National Key Project for Fundamental Research in China,Grant NSC 92097
文摘In an optoelectronic 2-D programmable neural network system, optical data need to be transferred and feedback with high speed. This paper presents the design and implementation of the interface circuit and its software.
基金Supported by the National High Techology Devel opment 863 Program of China(2002AA1Z030) and China PostdoctoralScience Foundation(2003034151)
文摘Single-chip multiprocessor (CMP) combined with the fault-loleranl(FT)techniques offers an ideal architecture to achieve high availability on the basis of sustaining highcomputing performance FT design of a single-chip multiprocessor is described, including thetechniques from hard-wart redundancy to software support and firmware strategy. The design aims atmasking the influences of errors and automatically correcting the system states.
文摘This paper uses CT to gain the energy directly from the high-voltage transmission line, to address the problem of power supply for monitoring system in high voltage side of transmission line. The draw-out power coil can induce voltage from the transmission line, using single-chip microcomputer to analog and output PMW wave to control the charging module, provides a stable 3.4 V DC voltage to the load, and solve the problem of easy saturating of core. The power supply based on this kind of draw-out power coil has undergone the overall testing, and it is verified-showing that it can properly work in a non-saturated status within the current range of 50 - 1000 A, and provide a stable output. The equipment also design protection circuit to improve the reliability to avid the impacts of the impulse current or short-circuit current. It effectively solves the problem of power supply for On-line Monitoring System of Transmission.
文摘A Smart resistance thermometer sensor is designed to overcome the shortages of the traditional ones, and Con-form to the world development trend of the sensor market.According to the constitutions of this Smart sensor and its application coverage,those parts with good -application and low-cost were chosen to constitute this sensor on the basis of full consideration of the linkage among every part.The whole testing system were controlled and processed by C8051F350 single-chip,it could measure precise temperature by PT100 resistance thermometer and circumstance temperature for temperature compensating automatically and simultane-ously,it also could amplify signals to convert analog signals to digital ones,and display results automatically by analysing and processing information.Furthermore,it could auto-compensate self-check,and spot communicate.
文摘In view of domestic scientific and technological achievements at present,real-time control circuit for greenhouse temperature and light intensity has been designed in line with the principle of cost saving and easy control.With advanced temperature sensor and light sensor applied to measure the temperature and light intensity,an execution unit is controlled by single-chip microcomputer(SCM)to regulate the temperature and light intensity,creating a hardware design scheme and software design idea.In case of high temperature and high light intensity in greenhouse,the sunshade net will be put down and the blower will be started automatically;in case of low temperature and light intensity,the sunshade net will be folded up and the heating valve will be turned up automatically.In this way,the temperature and light intensity in greenhouse will be controlled within the designed range.
基金This work is supported by Guangxi Vocational Education Teaching Reform Research Project(GXGZJG2020B149)Higher Education Department of the Ministry of Education Industry-University Cooperative Education Project.
文摘Mainly introduces intelligent classification trash can be dedicated to solving indoor household garbage classification.The trash can is based on AT89S52 single-chip microcomputer as the main control chip.The single-chip microcomputer realizes the intelligent classification of garbage by controlling the voice module,mechanical drive module,and infrared detection module.The use of voice control technology and infrared detection technology makes the trash can have voice control and overflow alarm functions.The design has the advantages of simple and intelligent operation,simple structure,stable performance,low investment,etc.,which can further effectively isolate people and garbage,reduce human infection with bacteria,and is a feasible solution for classification at the source of garbage.
文摘A low power dissipation control system for continuous cyclic peritoneal dialysis (CCPD) cycler and its characteristics are reported. Combined withhemodialysis and renal transplantation, peritoneal dialysis is used mainly for thetreatment of renal failure. CCPD has been developed during 1980's. It provided automatic dialysis procedures during the night to avoid interruptions in patients'dailyroutine. Furthermore,there is a remarkable decrease in peritonitis occurance usingCCPD. The control system is a critical part for CCPD cycler. The system is approvedto be reliable and flexible in practical experiments. When AC power failure,the system can still ensure the completion of dialysis.
基金This work was supported by National 863 plan item of China( No:863 -3 0 6-ZD-0 50 2 )
文摘objective: To introduce the development of a portable multi-parameter monitoring system. Methods: Using signal detecting and data processing techniques, this monitor with a graphic liquid crystal display (LCD) and a single-chip microprocessor 8Xc196Kc can dynamically measure electrocardiogram(ECG), breath wave, blood pressure (BP), breath frequency (BF), heart rate (HR) and body temperature (BT) in real-time. Results: This monitor can dynamically display the ECG, breath wave and other parameters in real time. It can also provide a 24h trend graph for each measured parameter and exchange data, through the serial communication interface (RS232), with the PC or hand-held PC (HPC). Conclusions: This portable monitoring system has a man-machine interface friendly. It is capable of performing continuous monitoring and also used as terminal of a central monitoring system or a tele-monitoring system.
文摘This paper presents a single-chip 3D electric field microsensor, in which a sensing element is set at the center to detect the Z-axis component of an electrostatic field. Two pairs of sensing elements with the same structure are arranged in a cross-like configuration to measure the X- and Y-axis electrostatic field components. An in-plane rotary mechanism is used in the microsensor to detect the X-, Y-, and Z-axis electrostatic field components simultaneously. The proposed microsensor is compact and presents high integration. The microsensor is fabricated through a MetalMUMPS process. Experimental results show that in the range of 0-50 kV/m, the linearity errors of the microsensor are within 5.5%, and the total measure- ment errors of the three electrostatic field components are less than 14.04%.
基金Foundation item:Key Basic Research Project of Science and Technology Commission of Shanghai(10JC1406000)
文摘The problem of digital controlling of high frequency microplasma arc welding machine has been solved through Fujitsu 16-bits single-chip processor used.Digital welding power sources and their control systems,digital sequential control system,and digital man-machine interaction system were included in digital microplasma arc welding machine studied.Principles,which is about digital sequential control system,digital man-machine interaction system,digital controller and its interface,and controlling software program,were analyzed.It has been showed that full digitalization of high frequency microplasma arc welding machine was fulfilled,minimum welding current of the machine is 0.05A,and arc is stable and can been started unfailingly.
基金This work is supported by the National Science Foundation of USA under Grant Nos. CCF-1065147, ECCS-1125762, the Scholarship Council of China, as well as the Beijing Institute of Technology Yu-Miao Ph.D. Scholarship of China. Any opinions, findings, and conclusions as well as recommendations expressed in this material are those of the authors and do not necessarily reflect the views neither of the National Science Foundation of USA nor of the Scholarship Council of China.
文摘Nowadays, we are heading towards integrating hundreds to thousands of cores on a single chip. However, traditional system software and middleware are not well suited to manage and provide services at such large scale. To improve the scalability and adaptability of operating system and middleware services on future many-core platform, we propose the pinned OS/services. By porting each OS and runtime system (middleware) service to a separate core (special hardware acceleration), we expect to achieve maximal performance gain and energy efficiency in many-core environments. As a case study, we target on XML (Extensible Markup Language), the commonly used data transfer/store standard in the world. We have successfully implemented and evaluated the design of porting XML parsing service onto Intel 48-core Single-Chip Cloud Computer (SCC) platform. The results show that it can provide considerable energy saving. However, we also identified heavy performance penalties introduced from memory side, making the parsing service bloated. Hence, as a further step, we propose the memory-side hardware accelerator for XML parsing. With specified hardware design, we can further enhance the performance gain and energy efficiency, where the performance can be improved by 20% with 12.27% energy reduction.
基金supported by the Innovation Fund for Small Technology-based Firms of China (No.06C26222200838).
文摘Working principles of silicon double P-N junction color sensor are introduced and a color measurement system to distinguish tooth color difference is designed in this paper.This system consists of silicon double P-N junction,a small optical fiber probe,signal process circuit and an MSP430FG439 single-chip system.Small in size,this system can measure different parts of the tooth in a fast and convenient way with high-accuracy.Thus,this system will be very promising in building prosthodontics and tooth fabrication.