Experimental demonstration of single-mode fiber coupling using adaptive fiber coupler

Coupling plane wave into a single-mode fiber （SMF） with high and steady coupling efficiency is crucial for fiber- based free-space laser systems, where random angular jitters are the main influencing factors of fiber coupling. In this paper, we verified a new adaptive-optic device named adaptive fiber coupler （AFC） which could compensate angular jitters and improve the SMF coupling efficiency in some degree. Experiments of SMF coupling under the angular jitter situation using AFC have been achieved. Stochastic parallel gradient descent （SPGD） algorithm is employed as the control strategy, of which the iteration rate is 625 Hz. In closed loop, the coupling efficiency keeps above 65% when angular errors are below 80/3tad. The compensation bandwidth is 35 Hz at sine-jitter of 15 ~rad amplitude with average coupling efficiency of above 60%. Also, experiments with simulated turbulence have been studied. The average coupling efficiency increases from 31.97% in open loop to 61.33% in closed loop, and mean square error （MSE） of coupling efficiency drops from 7.43% to 1.75%.

Wavelength dependent loss of splice of single-mode fibers

After reviewing three different definitions of mode field diameter of single-mode fibers, coupled efficiency calculation methods associated with lateral offset, longitude separation and wavelength, the effects produced by them, and the influences of splicing defects were discussed in detail. The regularities of the effects were studied according to the first order derivation of couple efficiency formula, and a simplified formula for couple efficiency calculation was presented under the circumstance of slight misalignment, with respect to wavelength, 2, and in a good agreement with the theoretical model. The simplified formula provides a new but simple approach to evaluate wavelength dependent couple efficiency of single-mode fibers. Theoretical analyses and numerical calculations show that, when those defects exist, the wavelength produces additional effects on the couple loss that growth of wavelength causes an increase on the couple efficiency for the lateral offset or longitude separation whereas lessens the couple efficiency due to angular misalignment or mode fields mismatching, and that the wavelength degrades the couple efficiency distinctly when λ≥2.5 μm whereas it distorts the couple slightly in range of λ≤2λ≤2 μm.

Single-mode antiresonant terahertz fiber based on mode coupling between core and cladding

Based on the index-induced mode coupling between the higher-order mode in core and the fundamental mode in cladding tubes,the single-mode operation can be realized in any antiresonant fibers(ARFs)when satisfying that the area ratio of cladding tube and core is about 0.46:1,and this area ratio also should be modified according to the shape and the number of cladding tubes.In the ARF with nodal core boundary,the mode in core also can couple with the mode in the wall of core boundary,which can further enhance the suppression of high-order mode.Accordingly,an ARF with conjoint semi-elliptical cladding tubes realizes a loss of higher-order mode larger than 30 dB/m;simultaneously,a loss of fundamental mode loss less than 0.4 dB/m.

FAST EVALUATION OF THE CHARACTERISTICS OF SINGLE-MODE OPTICAL FIBERS

This paper describes a method for fast engineering evaluation of the transmission characteristicsof single-mode optical fibers.A versatile microcomputer program is presented which can be utilized to ana-lyze mode field characteristics of single-mode fibers with arbitrary refractive index profiles.Our computationshows that the mathematical algorithm and the corresponding programs developeod in this paper are rela-tively simple and accurate enough for the engineenring design of single-mode fibers for optical communica-tion systems.

Single-polarization single-mode hollow-core negative curvature fiber with nested U-type cladding elements

Hollow-core negative curvature fibers(HC-NCFs)have become one of the research hotspots in the field of optical fiber because of their potential applications in the data and energy transmissions.In this work,a new kind of single-polarization single-mode HC-NCF with nested U-type cladding elements is proposed.To achieve the single-polarization single-mode transmission,we use two different silica tubes in thickness,which satisfy the resonance and anti-resonance conditions on the U-type cladding elements and the cladding tubes,respectively.Besides,the elliptical elements are introduced to achieve good single-mode performance.By studying the influences of the structure parameters on the propagation characteristics,the optimized structure parameters are obtained.The simulation results show that when the wavelength is fixed at 1550 nm,the single-polarization single-mode transmission is achieved,with the polarization extinction ratio of 25749 and minimum high-order mode extinction ratio of 174.Furthermore,the confinement loss is only 0.0015 dB/m.

Frequency-stabilized Yb：fiber comb with a tapered single-mode fiber

We demonstrate a stable Yb：fiber frequency comb with supercontinuum generation by using a specially designed tapered single-mode fiber, in which a spectrum spanning from 500 nm to 1500 nm is produced. The carrier-envelope offset signal of the Yb：fiber comb is measured with a signal-to-noise ratio of more than 40 dB and a linewidth narrower than 120 kHz. The repetition rate and carrier-envelope offset signals are simultaneously phase locked to a microwave reference frequency.

A tunable comb filter using single-mode/multimode/polarization-maintaining-fiber-based Sagnac fiber loop

A novel tunable comb filter composed of a single-mode/multimode/polarization-maintaining-fiber-based Sagnac fiber loop is proposed and experimentally demonstrated. The filter tunability is achieved by rotating the polarization controller. The spectral shift is dependent on rotation direction and the position of the polarization controller. In addition, the adjustable range achieved by rotating the half-wave-plate polarization controller is twice higher than that of the quarter-wave-plate one.

Effect of aluminum silicate fiber modification on crack-resistance of a ceramic mould

To improve the crack-resistance of the mould for silica sol bonded quartz based ceramic mould casting,aluminum silicate fibers with the diameter ranging from 5 μm to 25 μm and the length about 1 mm were dispersed in the ceramic mould.The effect of the aluminum silicate fibers on the tensile strength,shrinkage rate and the cracking trend of the ceramic mould were investigated.In the ceramic slurry,quartz sand was applied as ceramic aggregate,silica sol containing 30% silicon dioxide as bonder,and the weight ratio of quartz sand to silica sol was 2.69;the dispersed fibers changed from 0 to 0.24vol.%.The mould samples were formed after the slurry was poured and gelled at room temperature,and then sintered at different temperatures ranging from 100 to 800 ℃ to measure the tensile strength and shrinkage rate.The results show that,with the aluminum silicate fiber addition increasing from 0 to 0.24vol.%,the tensile strength increases linearly from 0.175 MPa to 0.236 MPa,and the shrinkage rate decreases linearly from 1.75% to 1.68% for the ceramic mould sintered at 400 ℃,from 1.37% to 1.31% for the ceramic mould at room temperature.As the sintering temperature was raised from 100 ℃ to 800 ℃,the tensile strength increases,and the shrinkage rate decreases at all temperatures,compared with those without fiber dispersion,but their variation patterns remain the same.Furthermore,the cracking trend of the mould and its decreasing proportion were defined and analyzed quantitatively considering both effects of the fiber dispersion on the strength and shrinkage.The cracking trend appears to decrease linearly with increasing fiber content and to reach the maximum reduction of 28.8% when 0.24vol.% fiber was dispersed.Therefore,the investigation proposes a new method to improve the crack-resistance of the ceramic mould,i.e.,inorganic fiber dispersion into the ceramic mould.

Fusion Splicing Experiments of 1060-XP Silica Fiber with Phosphate Glass Fiber

An asymmetric heating method for fusion splicing of 1 060-XP silica fiber （1 060F） and phosphate glass fiber （PGF） using an electric arc splicer has been proposed. Double joints with the lowest splice loss of 0.6 dB and good bending-resist strength between 1 060 F and PGF has been obtained. The main reasons affecting fiber splice loss and strength have been analyzed.

Low Temperature Coating of Anatase Thin Films on Silica Glass Fibers by Liquid Phase Deposition

Uniform crystalline TiO2 thin films were coated on silica glass fibers by liquid phase deposition from aqueous solution of ammonium hexafluorotitanate at low temperature. TiO2 thin films and nanopowders were prepared by adding H3BO3 into （NH4）2TiF6 solution supersaturated with anatase nano-crystalline TiO2 at 40 ℃. The effects of the deposition conditions on the surface morphology, section morphology, thickness of the deposited TiO2 thin films were investigated. The results indicate that the growth rate and particle size of the thin films were controlled by both the deposition conditions and the amount of anatase nano-crystalline TiO2.

Erbium-Doped Zirconia-Alumina Silica Glass-Based Fiber as a Saturable Absorber for High Repetition Rate Q-Switched All-Fiber Laser Generation

We propose and demonstrate a Q-switched erbium-doped fiber laser （EDFL） using an erbium-doped zirconia-alumina silica glass-based fiber （Zr-EDF） as a saturable absorber. As a 16-cm-long Zr-EDF is incorporated into a ring EDFL cavity, a stable Q-switching pulse train operating at 1565？nm wavelength is successfully obtained. The repetition rate is tunable from 33.97？kHz to 71.23？kHz by increasing the pump power from the threshold of 26？mW to the maximum of 74？mW. The highest pulse energy of 26.67？nJ is obtained at the maximum pump power.

Effects of precoating and calcination on microstructure of 3D silica fiber reinforced silicon nitride based composites

Three-dimensional silica fiber reinforced silicon nitride based composites were fabricated by preceramic polymer infiltration and pyrolysis method using perhydropolysilazane as a precursor. The effects of precoating and high temperature calcination on the microstructures of the composites were investigated by scanning electron microscopy. For the composite without a precoating, the fracture surface is plain, and the fiber/matrix interfaces become very unclear after calcination at 1 600 ℃ due to intense interfacial reactions. The composite with a precoating shows tough fracture surface with distinct fiber pull-outs, and the fiber/matrix interfaces are still clear after calcination at 1 600 ℃. It is the appropriate precoating process that contributes to the good interfacial microstructures for the composite.

Processing and performance of 2D fused-silica fiber reinforced porous Si_3N_4 matrix composites

Two-dimension （2D） fused-silica fiber reinforced porous silicon nitride matrix composites were fabricated using slurry impregnation and cyclic infiltration with colloidal silica sol. The microstructure and fracture surface were characterized by SEM, the mechanical behavior was investigated by three-point bending test, and the dielectric constant was also measured by impedance analysis. The microstructure showed that the fiber and the matrix had a physical bonding, forming a clearance interface. The mechanical behavior suggested that the porous matrix acted as crack deflection, and the fracture surface had a lot of fiber pull-out. However, the interlaminar shear strength was not so good. The dielectric constant of the composites at room temperature was about 2.8-3.1. The relatively low dielectric constant and non-catastrophic failure indicated the potential application in the radome materials field. 2008 University of Science and Technology Beijing. All rights reserved.

300 000 Image-elements Silica Fiber for Image-transmission

A high capacity image-transmission silica fiber was prepared in North Jiaotong Universitysuccessfully.It is a result of cooperative development with Beijing Micro-technique Institute andBeijing Fabric No.605.This fiber shows high-resolution,high-transmittance and high-qualitycolour-fidelity.

Electron-Irradiation and Photo-Excitation Darkening and Bleaching of Yb Doped Silica Fibers: Comparison

We report a comparative experimental study of the attenuation spectra transformations for a series of Yb doped alumino-germano silicate fibers with different contents of Yb3+ dopants, which arise as the result of irradiation either by a beam of high-energy electrons or by resonant (into the 977-nm absorption peak of YbYb3+ ions) optical pumping. The experimental data obtained reveal that in the two circumstances, substantial and complex but different in appearance changes occur within the resonant absorption band of YbYb3+ ions and in the off-resonance background loss of the fibers. Possible mechanisms responsible for these spectral changes are discussed.

Discussion on the Effects of Temperature, Carbon Fiber and Silica

Concrete, as an essential construction material in the construction industry, is the main component of solid waste. To improve the strength and durability of concrete, some additives can be added into concrete to replace parts of cement. Carbon fiber and silica powder are the most common additives. Under a series of experiments, the effects of temperature, carbon fiber and silica powder on the mechanical properties of concrete were studied under normal circumstances. In this paper, a conclusion on the effects was drawn up mainly through some experimental analyses, so as to discuss the effect laws and provide a reference to manufacture the concrete of high strength and properties.

Preparation of Carbon Nano-fiber Washcoat on Porous Silica Foam as Structured Catalyst Support

This paper reports how a hairy layer of carbon nano-fibers can be prepared on the macro-porous silica foam produced by the sphere templating method. Firstly, three-dimensional close-packed crystals of polystyrene spheres are assembled on porous disk substrate by vacuum filtration or evaporation. The polystyrene template is annealed slightly above the glass transition temperature in order to strengthen the colloidal crystal and ensure inter- connection of the spheres so as to obtain porous materials with open structure. Following the treatment of hexde- cyltrimethylammonium bromide, the polystyrene template is filled with silica colloidal solution, which solidifies in the cavities. Then the polystyrene particles are removed by calcination at 843K, leaving behind porous silica foam. Scanning electron microscopy images demonstrate that silica foam has uniform and open structured pores. Nickel particles were deposited on porous silica foam layer by the dipping method and porous carbon nano-fiber washcoat was prepared by catalytic decomposition of ethene over small nickel particles.

An Effective Thermal Splicing Method to Join Fluoride and Silica Fibers for a High Power Regime

A repeatable and simple thermal splicing method for low loss splice between fluoride and silica fibers is presented. The minimum splicing loss of 0.58 dB is achieved experimentally with this approach, Meanwhile, the power capacity of this splicing joint is also tested with a high power fiber laser. The maximum input power is up to 15 W, only limited by the available power of the laser source. To the best of our knowledge, this is the first report on thermal splicing between fluoride and silica fibers operating in a high power regime without any complicated ion-assisted deposition process.

Mechanism of E' center induced by γ ray radiation in silica optical fiber material

The characteristics of the best known defect centers E' in silica optical fiber material irradiated with ray were investigated by ESR at room temperature.A mechanism model of production of the E' center defect was established.The production of E' center includes two processes creation and activation.The strained bonds(or oxygen replacement) in silica networks lead to the creation of new defects whose concentration increases linearly with the dose.The pre-existing defects produce the activation,which tends to saturation.According to this model,the relation of E' center concentration changing with irradiation dose was obtained theoretically.The results are in good agreement with the experimental results.

海泡石纤维表面包覆二氧化硅增强油井水泥的力学性能

【目的】降低天然海泡石纤维的吸水性,提高海泡石纤维水泥浆的流动性能,改善水泥石的力学性能。【方法】通过酸-水热法对天然海泡石纤维进行除杂提纯,并采用正硅酸乙酯(tetraethyl orthosilicate,TEOS)水解在海泡石纤维表面包覆二氧化硅降低海泡石纤维的吸水性,探究海泡石纤维对油井水泥的浆体性能、力学性能影响;运用X射线衍射分析、热分析和扫描电子显微镜分析等方法表征水泥石的物相组成、水化程度及微观形貌。【结果】改性水泥的海泡石纤维最优质量分数为5%,固化7 d的水泥石抗压、抗拉强度较未改性的分别提高了10.98%、10.58%;海泡石纤维质量分数为5%的改性水泥石的峰值应力为35.76 MPa,峰值应变为3.97×10^(-2)。海泡石纤维表面包覆SiO_(2)后,在较低质量分数下(5%)就能够促进水泥水化。【结论】改性海泡石纤维水泥浆的流动性优于未改性的;在纤维掺量和养护时间相同的情况下,改性海泡石纤维水泥石的抗压强度和抗拉强度均高于未改性的;改性海泡石纤维对水泥石的增韧强化能力高于未改性海泡石纤维。