Cd_(1-x)Zn_(x)S thin films were deposited by chemical bath deposition(CBD)on the glass substrate to study the influence of cadmium sulfate concentration on the structural characteristics of the thin film.The SEM resul...Cd_(1-x)Zn_(x)S thin films were deposited by chemical bath deposition(CBD)on the glass substrate to study the influence of cadmium sulfate concentration on the structural characteristics of the thin film.The SEM results show that the thin film surfaces under the cadmium sulfate concentration of 0.005 M exhibit better compactness and uniformity.The distribution diagrams of thin film elements illustrate the film growth rate changes on the trend of the increase,decrease,and increase with the increase of cadmium sulfate concentration.XRD studies exhibit the crystal structure of the film is the hexagonal phase,and there are obvious diffraction peaks and better crystallinity when the concentration is 0.005 M.Spectrophotometer test results demonstrate that the relationship between zinc content x and optical band gap value E_(g) can be expressed by the equation E_(g)(x)=0.59x^(2)+0.69x+2.43.Increasing the zinc content can increase the optical band gap,and the absorbance of the thin film can be improved by decreasing the cadmium sulfate concentration,however,all of them have good transmittance.At a concentration of 0.005 M,the thin film has good absorbance in the 300-800 nm range,80%transmittance,and band gap value of 3.24 eV,which is suitable for use as a buffer layer for solar cells.展开更多
Ternary In-rich AlxIn1-x N films were successfully grown on Si （111） and （0001） sapphire substrates by radio-frequency magnetron sputtering on a relatively Al-rich AlxIn1-x N layer after AlN buffer. X-ray diffract...Ternary In-rich AlxIn1-x N films were successfully grown on Si （111） and （0001） sapphire substrates by radio-frequency magnetron sputtering on a relatively Al-rich AlxIn1-x N layer after AlN buffer. X-ray diffraction （XRD） patterns of the films indicate highly c axis-oriented wurtzite structure and the indium content of about 0.76 has been evaluated according to the Vegard＇s law. An Al-rich AlxIn1-xN transition layer was formed between the ultimate In-rich AlxIn1-x N film and the AlN buffer, which served as a further buffer to alleviate mismatch. X-ray photoelectron spectroscopy （XPS） depth profiling analyses confirm the alternative of indium and aluminum composition and the unavoidable oxygen impurities from surface to bulk. Owing to high indium content, obvious E2u and InN-like Al （LO） phonon model accompanying with slight A1N-like A1 （LO） phonon model are observed. Hall effect measurements demonstrate n-type electrical conductivity in these alloys with carrier concentrations n=1019 cm-3. The strain in In-rich AlxIn1-x N films can be significantly reduced by introducing an Al-rich interlayer, facilitating the improvement of film quality for diverse device applications.展开更多
Cux（Cu2O）1-x（0.09 x 1.00） granular films with thickness about 280 nm have been fabricated by direct current reactive magnetron sputtering. The atomic ratio x can be controlled by the oxygen flow rate during Cux（C...Cux（Cu2O）1-x（0.09 x 1.00） granular films with thickness about 280 nm have been fabricated by direct current reactive magnetron sputtering. The atomic ratio x can be controlled by the oxygen flow rate during Cux（Cu2O）1-x deposition. Room-temperature ferromagnetism（FM） is found in all of the samples. The saturated magnetization increases at first and then decreases with the decrease of x. The photoluminescence spectra show that the magnetization is closely correlated with the Cu vacancies in the Cux（Cu2O）1-x granular films. Fundamentally, the FM could be understood by the Stoner model based on the charge transfer mechanism. These results may provide solid evidence and physical insights on the origin of FM in the Cu2O-based oxides diluted magnetic semiconductors, especially for systems without intentional magnetic atom doping.展开更多
Zn_(1-x)Mg_(x)O alloy films are important deep ultraviolet photoelectric materials.In this work,we used plasma-assisted molecular beam epitaxy to prepare Zn_(1-x)Mg_(x)O films with different magnesium contents on pola...Zn_(1-x)Mg_(x)O alloy films are important deep ultraviolet photoelectric materials.In this work,we used plasma-assisted molecular beam epitaxy to prepare Zn_(1-x)Mg_(x)O films with different magnesium contents on polar(0001)and nonpolar(1010)ZnO substrates.The nanoscale structural features of the grown alloy films as well as the interfaces were investigated.It was observed that the cubic phases of the alloy films emerged when the Mg content reached 20%and 37%for the alloy films grown on the(0001)and(1010)ZnO substrates,respectively.High-resolution transmission electron microscopy images revealed cubic phases without visible hexagonal phases for the alloy films with more than 70%magnesium,and the cubic phases exhibited three-fold and two-fold rotations for the alloy films on the polar(0001)and nonpolar(1010)ZnO substrates,respectively.This work aims to provide references for monitoring the Zn_(1-x)Mg_(x)O film structure with respect to different substrate orientations.展开更多
Stoichiometric Ba（MnxTi（1-x）O3） （BMT） thin films with various values of x were deposited on Si（111） substrates by the sol-gel technique. The influence of Mn content on the optical properties was studied by spe...Stoichiometric Ba（MnxTi（1-x）O3） （BMT） thin films with various values of x were deposited on Si（111） substrates by the sol-gel technique. The influence of Mn content on the optical properties was studied by spectroscopic ellipsometry （SE） in the UV–Vis–NIR region. By fitting the measured ellipsometric parameter （Ψ and Δ） with a four-phase model （air/BMT＋voids/BMT/Si（111））, the key optical constants of the thin films have been obtained. It was found that the refractive index n and the extinction coefficient k increase with increasing Mn content due to the increase in the packing density. Furthermore, a strong dependence of the optical band gap Eg on Mn/Ti ratios in the deposited films was observed, and it was inferred that the energy level of conduction bands decreases with increasing Mn content.展开更多
Y_(1-x)Ho_xBa_2Cu_3O_(7-δ)(0<x<1) sinsle crystal thin films oriented with the caxis perpendicular to the sur-face were grown by DC magnetron sputtering technique. Target was pieced together with half of YBa_2Cu...Y_(1-x)Ho_xBa_2Cu_3O_(7-δ)(0<x<1) sinsle crystal thin films oriented with the caxis perpendicular to the sur-face were grown by DC magnetron sputtering technique. Target was pieced together with half of YBa_2Cu_3O_(7-δ)(YBCO) and half of HoBa_2Cu_3O_(7-δ)(HBCO) superconducting materials. As the distance between HBCO targetmaterial and substrate is varied , the Ho content in material is changed respectively. When the content of Ho is0. 7 (atom ratio) , the T_c>83K.展开更多
The CuxSi（1-x） thin films have been grown by pulsed laser deposition（PLD） with in situ annealing on Si（001） and Si（111）,respectively.The transformation of phase was detected by X-ray diffraction（XRD）.The res...The CuxSi（1-x） thin films have been grown by pulsed laser deposition（PLD） with in situ annealing on Si（001） and Si（111）,respectively.The transformation of phase was detected by X-ray diffraction（XRD）.The results showed that the as-deposited films were composed of Cu on both Si（001） and Si（111）.The annealed thin films consisted of Cu ＋η ＂-Cu3Si on Si（001） while Cu ＋η＇-Cu3Si on Si（111）,respectively,at annealed temperature（Ta）= 300-600℃.With the further increasing of Ta,at Ta= 700℃,there was only one main phase,η＂-Cu3Si on Si（001） while η＇-Cu3Si on Si（111）,respectively.The annealed thin films transformed from continuous dense structure to scattered-grain morphology with increasing Ta detected by field emission scanning electron microscope（FESEM）.It was also showed that the grain size would enlarge with increasing annealing time（ta）.展开更多
Cadmium Cobalt Sulphide (CdxCo1-xS) thin film was deposited on microscopic glass substrate using chemical bath deposition technique at room temperature from aqueous solutions of Cadmium Chloride, Cobalt Chloride and T...Cadmium Cobalt Sulphide (CdxCo1-xS) thin film was deposited on microscopic glass substrate using chemical bath deposition technique at room temperature from aqueous solutions of Cadmium Chloride, Cobalt Chloride and Thiourea in which ammonium solution was used as complexing agents. The optical properties were characterized using the absorbance and transmission measurement from Unico UV-2102 PC spectrophotometer, at normal incidence of light in the wavelength range of 200 - 1000 nm. We report the deposition and optimization of the growth parameter with respect to time which showed that the band gap energy and the composition verified from the extended Vegard’s law are highly dependent on deposition time. The average transmittance of the film in VIS-NIR region ranges between 30% and 78% with absorbance range of 0.15 - 0.47 within the same wavelength range. The film was also observed to exhibit poor reflectance (11 x = 0.75;0.83 and 0.94), respectively. Other optical and dielectric properties of the films were also characterized. Based on the exhibited properties of the film, it can be concluded that it is a promising material for selective coatings for solar cells;effective coatings for poultry houses;use as antireflective coating materials, and for fabrication of optoelectronic devices.展开更多
采用离子液体电沉积技术以ITO玻璃为基片以0.1mol/L Si Cl4+Ge Cl4的离子液体Py1.4Tf2N混合溶液作为电解液,利用循环伏安扫描法确定Si、Ge在离子液体中的共还原电位,完成Si、Ge的共沉积,制备出SixGe1-x薄膜.并对其电化学沉积机理进行分...采用离子液体电沉积技术以ITO玻璃为基片以0.1mol/L Si Cl4+Ge Cl4的离子液体Py1.4Tf2N混合溶液作为电解液,利用循环伏安扫描法确定Si、Ge在离子液体中的共还原电位,完成Si、Ge的共沉积,制备出SixGe1-x薄膜.并对其电化学沉积机理进行分析.利用X射线衍射仪(XRD)、扫描探针显微镜(SPM)、拉曼光谱(Raman)对样品的结构、表面进行了测量和分析.展开更多
Tunable and switchable Ba 0.5 Sr 0.5 TiO 3 film bulk acoustic resonators（FBARs） based on SiO 2 /Mo Bragg reflectors are explored,which can withstand high temperature for the deposition of Ba x Sr 1 x TiO 3（BST） fi...Tunable and switchable Ba 0.5 Sr 0.5 TiO 3 film bulk acoustic resonators（FBARs） based on SiO 2 /Mo Bragg reflectors are explored,which can withstand high temperature for the deposition of Ba x Sr 1 x TiO 3（BST） films at 800 C.The dc bias-dependent resonance may be attributed to the piezoelectricity of the BST film induced by an electrostrictive effect.The series resonant frequency is strongly dc bias-dependent and shifts downwards with dc bias increasing,while the parallel resonant frequency is only weakly dc bias-dependent and slightly shifts upwards at low dc bias（ 45 V） while downwards at higher dc bias.The calculated relative tunability of shifts at series resonance frequency is around 2.3% and the electromechanical coupling coefficient is up to approximately 8.09% at 60-V dc bias,which can be comparable to AlN FBARs.This suggests that a high-quality tunable BST FBAR device can be achieved through the use of molybdenum（Mo） as the high acoustic impedance layer in a Bragg reflector,which not only provides excellent acoustic isolation from the substrate,but also improves the crystallinity of BST films withstanding higher deposition temperature.展开更多
The development of superconductor/insulator/superconductor（SIS）tunnel junctions inthe cuprate high-temperature superconductor family has been hampered by an anisotropicstructure and a coherence length ξ as short as...The development of superconductor/insulator/superconductor（SIS）tunnel junctions inthe cuprate high-temperature superconductor family has been hampered by an anisotropicstructure and a coherence length ξ as short as 0.3 nm. However, the discovery of Ba<sub>1-x</sub>K<sub>x</sub>-BiO<sub>3</sub>（x≈0.4） superconductor which is an isotropic cubic structure and has a展开更多
基金This work was supported by the Tianjin Municipal Education Commission,Horizontal subject(grant number 70304901).
文摘Cd_(1-x)Zn_(x)S thin films were deposited by chemical bath deposition(CBD)on the glass substrate to study the influence of cadmium sulfate concentration on the structural characteristics of the thin film.The SEM results show that the thin film surfaces under the cadmium sulfate concentration of 0.005 M exhibit better compactness and uniformity.The distribution diagrams of thin film elements illustrate the film growth rate changes on the trend of the increase,decrease,and increase with the increase of cadmium sulfate concentration.XRD studies exhibit the crystal structure of the film is the hexagonal phase,and there are obvious diffraction peaks and better crystallinity when the concentration is 0.005 M.Spectrophotometer test results demonstrate that the relationship between zinc content x and optical band gap value E_(g) can be expressed by the equation E_(g)(x)=0.59x^(2)+0.69x+2.43.Increasing the zinc content can increase the optical band gap,and the absorbance of the thin film can be improved by decreasing the cadmium sulfate concentration,however,all of them have good transmittance.At a concentration of 0.005 M,the thin film has good absorbance in the 300-800 nm range,80%transmittance,and band gap value of 3.24 eV,which is suitable for use as a buffer layer for solar cells.
基金Supported by the 863 High-Technology Research and Development Program of China(No.2009AA03Z442)the National Natural Science Foundation of China(No.61077074)the Science and Technology Department of Jilin Province(No.20090422)
文摘Ternary In-rich AlxIn1-x N films were successfully grown on Si （111） and （0001） sapphire substrates by radio-frequency magnetron sputtering on a relatively Al-rich AlxIn1-x N layer after AlN buffer. X-ray diffraction （XRD） patterns of the films indicate highly c axis-oriented wurtzite structure and the indium content of about 0.76 has been evaluated according to the Vegard＇s law. An Al-rich AlxIn1-xN transition layer was formed between the ultimate In-rich AlxIn1-x N film and the AlN buffer, which served as a further buffer to alleviate mismatch. X-ray photoelectron spectroscopy （XPS） depth profiling analyses confirm the alternative of indium and aluminum composition and the unavoidable oxygen impurities from surface to bulk. Owing to high indium content, obvious E2u and InN-like Al （LO） phonon model accompanying with slight A1N-like A1 （LO） phonon model are observed. Hall effect measurements demonstrate n-type electrical conductivity in these alloys with carrier concentrations n=1019 cm-3. The strain in In-rich AlxIn1-x N films can be significantly reduced by introducing an Al-rich interlayer, facilitating the improvement of film quality for diverse device applications.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.11104148,51101088,and 51171082)the Tianjin Natural Science Foundation,China(Grant Nos.14JCZDJC37700 and 13JCQNJC02800)+1 种基金the Specialized Research Fund for the Doctoral Program of Higher Education,China(Grant No.20110031110034)the Fundamental Research Funds for the Central Universities,China
文摘Cux（Cu2O）1-x（0.09 x 1.00） granular films with thickness about 280 nm have been fabricated by direct current reactive magnetron sputtering. The atomic ratio x can be controlled by the oxygen flow rate during Cux（Cu2O）1-x deposition. Room-temperature ferromagnetism（FM） is found in all of the samples. The saturated magnetization increases at first and then decreases with the decrease of x. The photoluminescence spectra show that the magnetization is closely correlated with the Cu vacancies in the Cux（Cu2O）1-x granular films. Fundamentally, the FM could be understood by the Stoner model based on the charge transfer mechanism. These results may provide solid evidence and physical insights on the origin of FM in the Cu2O-based oxides diluted magnetic semiconductors, especially for systems without intentional magnetic atom doping.
基金Project supported by the National Natural Science Foundation of China(Grant No.11804050).
文摘Zn_(1-x)Mg_(x)O alloy films are important deep ultraviolet photoelectric materials.In this work,we used plasma-assisted molecular beam epitaxy to prepare Zn_(1-x)Mg_(x)O films with different magnesium contents on polar(0001)and nonpolar(1010)ZnO substrates.The nanoscale structural features of the grown alloy films as well as the interfaces were investigated.It was observed that the cubic phases of the alloy films emerged when the Mg content reached 20%and 37%for the alloy films grown on the(0001)and(1010)ZnO substrates,respectively.High-resolution transmission electron microscopy images revealed cubic phases without visible hexagonal phases for the alloy films with more than 70%magnesium,and the cubic phases exhibited three-fold and two-fold rotations for the alloy films on the polar(0001)and nonpolar(1010)ZnO substrates,respectively.This work aims to provide references for monitoring the Zn_(1-x)Mg_(x)O film structure with respect to different substrate orientations.
基金Project supported by the National Natural Science Foundation of China(Grant No.60976016)the Postdoctoral Science Foundation of China(Grant No.2012M511250)the Foundation Co-established by Henan Province and the Ministry of Henan University,China(Grant No.SBGJ090503)
文摘Stoichiometric Ba（MnxTi（1-x）O3） （BMT） thin films with various values of x were deposited on Si（111） substrates by the sol-gel technique. The influence of Mn content on the optical properties was studied by spectroscopic ellipsometry （SE） in the UV–Vis–NIR region. By fitting the measured ellipsometric parameter （Ψ and Δ） with a four-phase model （air/BMT＋voids/BMT/Si（111））, the key optical constants of the thin films have been obtained. It was found that the refractive index n and the extinction coefficient k increase with increasing Mn content due to the increase in the packing density. Furthermore, a strong dependence of the optical band gap Eg on Mn/Ti ratios in the deposited films was observed, and it was inferred that the energy level of conduction bands decreases with increasing Mn content.
文摘Y_(1-x)Ho_xBa_2Cu_3O_(7-δ)(0<x<1) sinsle crystal thin films oriented with the caxis perpendicular to the sur-face were grown by DC magnetron sputtering technique. Target was pieced together with half of YBa_2Cu_3O_(7-δ)(YBCO) and half of HoBa_2Cu_3O_(7-δ)(HBCO) superconducting materials. As the distance between HBCO targetmaterial and substrate is varied , the Ho content in material is changed respectively. When the content of Ho is0. 7 (atom ratio) , the T_c>83K.
基金Funded by National Natural Science Foundation of China(Nos.51102101,51272196,51372188,51521001)the 111 Project(No.B13035)+2 种基金the International Science&Technology Cooperation Program of China(No.2014DFA53090)the Natural Science Foundation of Hubei Province,China(No.2014CFB870)the Fundamental Research Funds for the Central Universities,China(No.WUT:2015III023)
文摘The CuxSi（1-x） thin films have been grown by pulsed laser deposition（PLD） with in situ annealing on Si（001） and Si（111）,respectively.The transformation of phase was detected by X-ray diffraction（XRD）.The results showed that the as-deposited films were composed of Cu on both Si（001） and Si（111）.The annealed thin films consisted of Cu ＋η ＂-Cu3Si on Si（001） while Cu ＋η＇-Cu3Si on Si（111）,respectively,at annealed temperature（Ta）= 300-600℃.With the further increasing of Ta,at Ta= 700℃,there was only one main phase,η＂-Cu3Si on Si（001） while η＇-Cu3Si on Si（111）,respectively.The annealed thin films transformed from continuous dense structure to scattered-grain morphology with increasing Ta detected by field emission scanning electron microscope（FESEM）.It was also showed that the grain size would enlarge with increasing annealing time（ta）.
文摘Cadmium Cobalt Sulphide (CdxCo1-xS) thin film was deposited on microscopic glass substrate using chemical bath deposition technique at room temperature from aqueous solutions of Cadmium Chloride, Cobalt Chloride and Thiourea in which ammonium solution was used as complexing agents. The optical properties were characterized using the absorbance and transmission measurement from Unico UV-2102 PC spectrophotometer, at normal incidence of light in the wavelength range of 200 - 1000 nm. We report the deposition and optimization of the growth parameter with respect to time which showed that the band gap energy and the composition verified from the extended Vegard’s law are highly dependent on deposition time. The average transmittance of the film in VIS-NIR region ranges between 30% and 78% with absorbance range of 0.15 - 0.47 within the same wavelength range. The film was also observed to exhibit poor reflectance (11 x = 0.75;0.83 and 0.94), respectively. Other optical and dielectric properties of the films were also characterized. Based on the exhibited properties of the film, it can be concluded that it is a promising material for selective coatings for solar cells;effective coatings for poultry houses;use as antireflective coating materials, and for fabrication of optoelectronic devices.
文摘采用离子液体电沉积技术以ITO玻璃为基片以0.1mol/L Si Cl4+Ge Cl4的离子液体Py1.4Tf2N混合溶液作为电解液,利用循环伏安扫描法确定Si、Ge在离子液体中的共还原电位,完成Si、Ge的共沉积,制备出SixGe1-x薄膜.并对其电化学沉积机理进行分析.利用X射线衍射仪(XRD)、扫描探针显微镜(SPM)、拉曼光谱(Raman)对样品的结构、表面进行了测量和分析.
基金Project supported by the National Natural Science Foundation of China (Grant Nos. 60871049 and 50972024)
文摘Tunable and switchable Ba 0.5 Sr 0.5 TiO 3 film bulk acoustic resonators（FBARs） based on SiO 2 /Mo Bragg reflectors are explored,which can withstand high temperature for the deposition of Ba x Sr 1 x TiO 3（BST） films at 800 C.The dc bias-dependent resonance may be attributed to the piezoelectricity of the BST film induced by an electrostrictive effect.The series resonant frequency is strongly dc bias-dependent and shifts downwards with dc bias increasing,while the parallel resonant frequency is only weakly dc bias-dependent and slightly shifts upwards at low dc bias（ 45 V） while downwards at higher dc bias.The calculated relative tunability of shifts at series resonance frequency is around 2.3% and the electromechanical coupling coefficient is up to approximately 8.09% at 60-V dc bias,which can be comparable to AlN FBARs.This suggests that a high-quality tunable BST FBAR device can be achieved through the use of molybdenum（Mo） as the high acoustic impedance layer in a Bragg reflector,which not only provides excellent acoustic isolation from the substrate,but also improves the crystallinity of BST films withstanding higher deposition temperature.
基金Project supported by the National Center for Research and Development on Superconducting, the National Natural Science Foundation of China and the National Laboratory of Solid State Microstructure in Nanjing University.
文摘The development of superconductor/insulator/superconductor（SIS）tunnel junctions inthe cuprate high-temperature superconductor family has been hampered by an anisotropicstructure and a coherence length ξ as short as 0.3 nm. However, the discovery of Ba<sub>1-x</sub>K<sub>x</sub>-BiO<sub>3</sub>（x≈0.4） superconductor which is an isotropic cubic structure and has a
