Explosion resistance performance of reinforced concrete box girder coated with polyurea:Model test and numerical simulation

To study the anti-explosion protection effect of polyurea coating on reinforced concrete box girder,two segmental girder specimens were made at a scale of 1:3,numbered as G(without polyurea coating)and PCG(with polyurea coating).The failure characteristics and dynamic responses of the specimens were compared through conducting explosion tests.The reliability of the numerical simulation using LS-DYNA software was verified by the test results.The effects of different scaled distances,reinforcement ratios,concrete strengths,coating thicknesses and ranges of polyurea were studied.The results show that the polyurea coating can effectively enhance the anti-explosion performance of the girder.The top plate of middle chamber in specimen G forms an elliptical penetrating hole,while that in specimen PCG only shows a very slight local dent.The peak vertical displacement and residual displacement of PCG decrease by 74.8% and 73.7%,respectively,compared with those of specimen G.For the TNT explosion with small equivalent,the polyurea coating has a more significant protective effect on reducing the size of fracture.With the increase of TNT equivalent,the protective effect of polyurea on reducing girder displacement becomes more significant.The optimal reinforcement ratio,concrete strength,thickness and range of polyurea coating were also drawn.

Effects of sand sedimentation and wind erosion around sand barrier:Numerical simulation and wind tunnel test studies

Based on numerical simulations,this study highlights the sedimentation and erosion problems around a sand barrier through the relationship between the shear stress of the surface around the sand barrier and the critical shear stress of sand grains.The numerical simulation results were verified using data measured by the wind tunnel test.The results showed that when the porosity was the same,the size and position of the vortex on the leeward side of the sand barrier were related to the inlet wind speed.As the wind speed increased,the vortex volume increased and the positions of the separation and reattachment points moved toward the leeward side.When the porosity of the sand barrier was 30%,the strength of the acceleration zone above the sand barrier was the highest,and the strength of the acceleration zone was negatively correlated with the porosity.Sand erosion and sedimentation distance were related to wind speed.With an increase in wind speed,the sand grain forward erosion or reverse erosion areas on the leeward side of the sand barrier gradually replaced the sedimentation area.With an increase in porosity,the sand sedimentation distance on the leeward side of the sand barrier gradually shortened,and the sand erosion area gradually disappeared.The sand sedimentation distance on the leeward side of the sand barrier with 30%porosity was the longest.The numerical simulation results were in good agreement with the wind tunnel test results.Based on the sand erosion and sedimentation results of the numerical simulation and wind tunnel test,when the porosity was 30%,the protection effect of the High Density Polyethylene(HDPE)board sand barrier was best.

Three-dimensional finite element simulation and reconstruction of jointed rock models using CT scanning and photogrammetry

The geometry of joints has a significant influence on the mechanical properties of rocks.To simplify the curved joint shapes in rocks,the joint shape is usually treated as straight lines or planes in most laboratory experiments and numerical simulations.In this study,the computerized tomography (CT) scanning and photogrammetry were employed to obtain the internal and surface joint structures of a limestone sample,respectively.To describe the joint geometry,the edge detection algorithms and a three-dimensional (3D) matrix mapping method were applied to reconstruct CT-based and photogrammetry-based jointed rock models.For comparison tests,the numerical uniaxial compression tests were conducted on an intact rock sample and a sample with a joint simplified to a plane using the parallel computing method.The results indicate that the mechanical characteristics and failure process of jointed rocks are significantly affected by the geometry of joints.The presence of joints reduces the uniaxial compressive strength (UCS),elastic modulus,and released acoustic emission (AE) energy of rocks by 37%–67%,21%–24%,and 52%–90%,respectively.Compared to the simplified joint sample,the proposed photogrammetry-based numerical model makes the most of the limited geometry information of joints.The UCS,accumulative released AE energy,and elastic modulus of the photogrammetry-based sample were found to be very close to those of the CT-based sample.The UCS value of the simplified joint sample (i.e.38.5 MPa) is much lower than that of the CT-based sample (i.e.72.3 MPa).Additionally,the accumulative released AE energy observed in the simplified joint sample is 3.899 times lower than that observed in the CT-based sample.CT scanning provides a reliable means to visualize the joints in rocks,which can be used to verify the reliability of photogrammetry techniques.The application of the photogrammetry-based sample enables detailed analysis for estimating the mechanical properties of jointed rocks.

Design and Test of Closed Hydraulic Transmission System of 4WD High-clearance Wheeled Sprayer

In conjunction with the working characteristics of the high-clearance wheeled sprayer and the benefits of the closed hydraulic system,a series of reasonable working parameters should be established,and a hydraulic system that fulfills the requisite specifications should be designed.The AMESim software model is employed to construct a closed hydraulic transmission system,and the simulation analysis is then performed according to the data of hydraulic components.According to analysis results,the prototype can be optimized and upgraded,and a verification test is further carried out.The test results demonstrate that the designed closed hydraulic transmission system meets the actual working requirements of the high-clearance wheeled sprayer and provides a stable experimental platform for intelligent control of agricultural machinery.

基于SolidWorks Flow Simulation的PCB测试设备机柜散热仿真分析

为了解决PCB测试设备在机柜中温度过高导致被测产品损坏的问题。根据实际应用场景,设计出一款具有散热高效、结构紧凑、制作成本低的PCB测试设备机柜。结合PCB检测设备整体结构对其所在的机柜进行结构设计和散热仿真分析。主要以4台PCB测试设备满载运行在机柜中散热情况为研究对象。根据实际结构,使用SolidWorks对机柜和测试设备简化仿真模型进行建模,将简化模型导入到SolidWorks Flow Simulation中对机柜进行散热仿真分析。通过分析计算得出散热的分布情况和测试设备关键地方的温升数值,判断机柜散热结构的散热情况是否与预期结果一致。试验结果表明:常温下,在机柜中4台PCB测试设备满载测试时检测区域最高温度达到28℃左右,能够可持续运行状态并保持稳定工作。通过试验验证,机柜的散热实际温度与其散热仿真结果相符,证实了该机柜散热结构设计的合理性以及正确性,并且确定机柜散热结构设计方案。

Centrifugal model tests and numerical simulations for barrier dam break due to overtopping

The present study focuses on the breaching process and failure of barrier dams due to overtopping. In this work, a series of centrifugal model tests is presented to examine the failure mechanisms of landslide dams. Based on the experimental results, failure process and mechanism of barrier dam due to overtopping are analyzed and further verified by simulating the experimental overtopping failure process. The results indicate that the barrier dam will develop during the entire process of overtopping in the width direction, whereas the breach will cease to develop at an early stage in the depth direction because of the large particles that accumulate on the downstream slope. Moreover, headcut erosion can be clearly observed in the first two stages of overtopping, and coarsening on the downstream slope occurs in the last stage of overtopping. Thus, the bottom part of the barrier dam can survive after dam breaching and full dam failure becomes relatively rare for a barrier dam. Furthermore, the remaining breach would be smaller than that of a homogeneous cohesive dam under the same conditions.

On modeling approach for embedded real-time software simulation testing

Modeling technology has been introduced into software testing field. However, how to carry through the testing modeling effectively is still a difficulty. Based on combination of simulation modeling technology and embedded real-time software testing method, the process of simulation testing modeling is studied first. And then, the supporting environment of simulation testing modeling is put forward. Furthermore, an approach of embedded real-time software simulation testing modeling including modeling of cross-linked equipments of system under testing （SUT）, test case, testing scheduling, and testing system service is brought forward. Finally, the formalized description and execution system of testing models are given, with which we can realize real-time, closed loop, mad automated system testing for embedded real-time software.

Simulation of large-scale numerical substructure in real-time dynamic hybrid testing

A solution scheme is proposed in this paper for an existing RTDHT system to simulate large-scale finite element （FE） numerical substructures. The analysis of the FE numerical substructure is split into response analysis and signal generation tasks, and executed in two different target computers in real-time. One target computer implements the response analysis task, wherein a large time-step is used to solve the FE substructure, and another target computer implements the signal generation task, wherein an interpolation program is used to generate control signals in a small time-step to meet the input demand of the controller. By using this strategy, the scale of the FE numerical substructure simulation may be increased significantly. The proposed scheme is initially verified by two FE numerical substructure models with 98 and 1240 degrees of freedom （DOFs）. Thereafter, RTDHTs of a single frame-foundation structure are implemented where the foundation, considered as the numerical substructure, is simulated by the FE model with 1240 DOFs. Good agreements between the results of the RTDHT and those from the FE analysis in ABAQUS are obtained.

Simulation and Field Testing of Multiple Vehicles Collision Avoidance Algorithms

A global planning algorithm for intelligent vehicles is designed based on the A* algorithm, which provides intelligent vehicles with a global path towards their destinations. A distributed real-time multiple vehicle collision avoidance(MVCA)algorithm is proposed by extending the reciprocal n-body collision avoidance method. MVCA enables the intelligent vehicles to choose their destinations and control inputs independently,without needing to negotiate with each other or with the coordinator. Compared to the centralized trajectory-planning algorithm, MVCA reduces computation costs and greatly improves the robustness of the system. Because the destination of each intelligent vehicle can be regarded as private, which can be protected by MVCA, at the same time MVCA can provide a real-time trajectory planning for intelligent vehicles. Therefore,MVCA can better improve the safety of intelligent vehicles. The simulation was conducted in MATLAB, including crossroads scene simulation and circular exchange position simulation. The results show that MVCA behaves safely and reliably. The effects of latency and packet loss on MVCA are also statistically investigated through theoretically formulating broadcasting process based on one-dimensional Markov chain. The results uncover that the tolerant delay should not exceed the half of deciding cycle of trajectory planning, and shortening the sending interval could alleviate the negative effects caused by the packet loss to an extent. The cases of short delay(< 100100 ms) and low packet loss(< 5%) can bring little influence to those trajectory planning algorithms that only depend on V2 V to sense the context, but the unpredictable collision may occur if the delay and packet loss are further worsened. The MVCA was also tested by a real intelligent vehicle, the test results prove the operability of MVCA.

Model test and numerical simulation on the dynamic stability of the bedding rock slope under frequent microseisms

Shake table testing was performed to investigate the dynamic stability of a mid-dip bedding rock slope under frequent earthquakes. Then, numerical modelling was established to further study the slope dynamic stability under purely microseisms and the influence of five factors, including seismic amplitude, slope height, slope angle, strata inclination and strata thickness, were considered. The experimental results show that the natural frequency of the slope decreases and damping ratio increases as the earthquake loading times increase. The dynamic strength reduction method is adopted for the stability evaluation of the bedding rock slope in numerical simulation, and the slope stability decreases with the increase of seismic amplitude, increase of slope height, reduction of strata thickness and increase of slope angle. The failure mode of a mid-dip bedding rock slope in the shaking table test is integral slipping along the bedding surface with dipping tensile cracks at the slope rear edge going through the bedding surfaces. In the numerical simulation, the long-term stability of a mid-dip bedding slope is worst under frequent microseisms and the slope is at risk of integral sliding instability, whereas the slope rock mass is more broken than shown in the shaking table test. The research results are of practical significance to better understand the formation mechanism of reservoir landslides and prevent future landslide disasters.

Shaking table test and numerical simulation on the effect of reinforcement on the seismic safety of dam slopes

The seismic safety of the reinforcement dam slope is studied through shaking table test and numerical simulation.The dynamic characteristics of dam slopes,failure mechanism,seismic stability,as well as the effect of reinforcement during earthquakes are discussed.An elasto-plastic analysis method (FLAC) is used to simulate the dynamic failure process of the reinforcement dam slope.The change law of permanent displacement of dam slope is studied.The effect of the length and the space of reinforcement on the depth of slip surface and the slope stability are investigated.Good agreement is obtained between the numerical results and those from shaking table tests.The results show that the dynamic failure is a gradual process not at a particular time.With the increase of the reinforcement length or the decreasing reinforcement spacing,the slip surface becomes deeper and thus the slope stability is improved.The reinforcement can obviously enhance the overall stability of slope dam.It can also effectively control the shallow sliding of slope.These researches provide basic data for reinforcement measures design of earth-rockfill dam.

Geomechanics model test and numerical simulation of 2G-NPR bolt support effect in an active fault tunnel

Active faults are a common adverse geological phenomenon that can occur during tunnel excavation and has a very negative impact on the construction and operation of the tunnel.In this paper,the grade IV rock surrounding the cross-fault tunnel with poor geological conditions has been chosen for the study.The support capacity of 2^(nd) Generation-Negative Poisson’s Ratio(2G-NPR)bolt in an active fault tunnel has been carried out on the basis of relevant results obtained from the geomechanical model test and numerical investigations of failure model for existing unsupported fault tunnel.The investigation shows that surrounding rock of the tunnel is prone to shear deformation and crack formation along the fault,as a result,the rock mass on the upper part of the fault slips as a whole.Furthermore,small-scale deformation and loss of blocks are observed around the tunnel;however,the 2G-NPR bolt support is found to be helpful in keeping the overall tunnel intact without any damage and instability.Due to the blocking effect of fault,the stress of the surrounding rock on the upper and lower parts of the fault is significantly different,and the stress at the left shoulder of the tunnel is greater than that at the right shoulder.The asymmetrical arrangement of 2G-NPR bolts can effectively control the asymmetric deformation and instability of the surrounding rock.The present numerical scheme is in good agreement with the model test results,and can reasonably reflect the stress and displacement characteristics of the surrounding rock of the tunnel.In comparison to unsupported and ordinary PR(Poisson’s Ratio)bolt support,2G-NPR bolt can effectively limit the fault slip and control the stability of the surrounding rock of the fault tunnel.The research findings may serve as a guideline for the use of 2G-NPR bolts in fault tunnel support engineering.

Trigger mechanism of loess-mudstone landslides inferred from ring shear tests and numerical simulation

Whereas loess-mudstone landslides are widely distributed and frequently occurred at the loess Plateau,this type of landslides is hard to detect due to its particularity,and easily generates serious losses.To clarify the shear characteristics and formation mechanism of loess-mudstone landslides,field investigations,ring shear tests and numerical simulation analyses were performed on the loess specimens collected from the Dingjiagou landslide in Yan’an city,China.The test results showed that both the peak strength and residual strength of slip zone soils have a decreasing tendency with moisture content,while the increasing of normal stress caused an increase in the shear strength.These phenomena indicate that the rise in the moisture content induced by precipitation or the decreasing of normal stress due to excavation activities would result in the weakening of slip zone soils.Numerical simulations of the evolution process of slope failure using the finite element method were conducted based on the Mohr–Coulomb criterion.It was found that the heavy precipitation played a more important role in the slope instability compared with the excavation.In addition,the field investigation showed that loess soils with well-developed cracks and underlying mudstone soils provide material base for the formation of loess-mudstone landslides.Finally,the formation mechanism of this type of landslides was divided into three stages,namely,the local deformation stage,the penetration stage,the creeping-sliding stage.This study may provide a basis for understanding the sliding process of loess-mudstone landslides,as well as guidelines for the prevention and mitigation of loess-mudstone landslides.

SIMULATION TEST APPARATUS FOR MARINE CORROSION

This paper describes the setup and working mechanism of a simulation test apparatus for marine corrosion. Experimental results showed the apparatus can basically reflect the corrosion behavior of steel in various marine environments, and is simple, convenient, and reliable for testing steel used for marine engineering.

Grassland Evolution Under Soil Degradation: Numerical Simulation and Test

Both theoretical and field observations were examined to study the close relationship between soil degeneration and the evolution of grassland vegetation. A general n-species model of equal competition under different degrees of soil degradation was applied to field data in order to probe the dynamic processes and mechanisms of vegetation evolution due to the effects of the soil's ecological deterioration on grassland vegetation. Comparisons were made between the theoretical results and the practical surveys with satisfactory results.

Numerical simulation of the behaviors of test square for prehistoric earthen sites during archaeological excavation

During the process of archaeological excavation in the regions of Southeast China, collapse of test square usually occurs due to poor site-specific conditions. In this paper, the fast Lagrangian analysis of continua in three dimensions（FLAC3D） is employed to reveal the behaviors of test square. Taking the archaeological works in Liangzhu prehistoric earthen sites as the research background, the paper first introduces the geological setting, excavation procedure and monitoring scheme of the studied test square. Then, the deformation of four sides of the test square is modeled using FLAC3D. By comparison, it shows that the numerical results are consistent with the results from field monitoring. The result suggests that the numerical simulation can be effectively applied to representing the actual behaviors of the test square,which is helpful for determination of excavation scheme and stability evaluation of the test square during archaeological excavation.

Test particle simulations of resonant interactions between energetic electrons and discrete, multi-frequency artificial whistler waves in the plasmasphere

Modulated high frequency （HF） heating of the ionosphere provides a feasible means of artificially generating ex- tremely low frequency （ELF）/very low frequency （VLF） whistler waves, which can leak into the inner magnetosphere and contribute to resonant interactions with high energy electrons. Combining the ray tracing method and test particle simulations, we evaluate the effects of energetic electron resonant scattering driven by the discrete, multi-frequency arti- ficially generated ELF/VLF waves. The simulation results indicate a stochastic behavior of electrons and a linear profile of pitch angle and kinetic energy variations averaged over all test electrons. These features are similar to those associated with single-frequency waves. The computed local diffusion coefficients show that, although the momentum diffusion of relativistic electrons due to artificial ELF/VLF whistlers with a nominal amplitude of ~ 1 pT is minor, the pitch angle scattering can be notably efficient at low pitch angles near the loss cone, which supports the feasibility of artificial triggering of multi-frequency ELF/VLF whistler waves for the removal of high energy electrons from the magnetosphere. We also investigate the dependences of diffusion coefficients on the frequency interval （△f） of the discrete, multi-frequency waves. We find that there is a threshold value of Af for which the net diffusion coefficient of multi-frequency whistlers is inversely proportional to △f （proportional to the frequency components Nw） when △f is below the threshold value but it remains unchanged with increasing Af when △f is larger than the threshold value. This is explained as being due to the fact that the resonant scattering effect of broadband waves is the sum of the effects of each frequency in the ＇effective frequency band＇. Our results suggest that the modulation frequency of HF heating of the ionosphere can be appropriately selected with reasonable frequency intervals so that better performance of controlled precipitation of high energy electrons in the plasmasphere by artificial ELF/VLF whistler waves can be achieved.

Real-time multibody modeling and simulation of a scaled bogie test rig

In wheel–rail adhesion studies,most of the test rigs used are simplified designs such as a single wheel or wheelset,but the results may not be accurate.Alternatively,representing the complex system by using a full vehicle model provides accurate results but may incur complexity in design.To trade off accuracy over complexity,a bogie model can be the optimum selection.Furthermore,only a real-time model can replicate its physical counterpart in the time domain.Developing such a model requires broad expertise and appropriate software and hardware.A few published works are available which deal with real-time modeling.However,the influence of the control system has not been included in those works.To address these issues,a real-time scaled bogie test rig including the control system is essential.Therefore,a 1:4 scaled bogie roller rig is developed to study the adhesion between wheel and roller contact.To compare the performances obtained from the scaled bogie test rig and to expand the test applications,a numerical simulation model of that scaled bogie test rig is developed using Gensys multibody software.This model is the complete model of the test rig which delivers more precise results.To exactly represent the physical counterpart system in the time domain,a real-time scaled bogie test rig(RT-SBTR)is developed after four consecutive stages.Then,to simulate the RT-SBTR to solve the internal state equations and functions representing the physical counterpart system in rigs used are simplified designs such as a single wheel or wheelset,but the results may not be accurate.Alternatively,representing the complex system by using a full vehicle model provides accurate results but may incur complexity in design.To trade off accuracy over complexity,a bogie model can be the optimum selection.Furthermore,only a real-time model can replicate its physical counterpart in the time domain.Developing such a model requires broad expertise and appropriate software and hardware.A few published works are available which deal with real-time modeling.However,the influence of the control system has not been included in those works.To address these issues,a real-time scaled bogie test rig including the control system is essential.Therefore,a 1:4 scaled bogie roller rig is developed to study the adhesion between wheel and roller contact.To compare the performances obtained from the scaled bogie test rig and to expand the test applications,a numerical simulation model of that scaled bogie test rig is developed using Gensys multibody software.This model is the complete model of the test rig which delivers more precise results.To exactly represent the physical counterpart system in the time domain,a real-time scaled bogie test rig(RT-SBTR)is developed after four consecutive stages.Then,to simulate the RT-SBTR to solve the internal state equations and functions representing the physical counterpart system in equal or less than actual time,the real-time simulation environment is prepared in two stages.To such end,the computational time improved from 4 times slower than real time to 2 times faster than real time.Finally,the real-time scaled bogie model is also incorporated with the braking control system which slightly reduces the computational performances without affecting real-time capability.

Study on electron stochastic motions in the magnetosonic wave field: Test particle simulations

Using the test particle simulation method, we investigate the stochastic motion of electrons with energy of 300 keV in a monochromatic magnetosonic(MS) wave field. This study is motivated by the violation of the quasi-linear theory assumption, when strong MS waves(amplitude up to ~1 nT) are present in the Earth's magnetosphere. First, electron motion can become stochastic when the wave amplitude exceeds a certain threshold. If an electron initially resonates with the MS wave via bounce resonance, as the bounce resonance order increases, the amplitude threshold of electron stochastic motion increases until it reaches the peak at about the 11 th order in our study, then the amplitude threshold slowly declines. Further, we find that the coexistence of bounce and Landau resonances between electrons and MS waves will significantly reduce the amplitude threshold. In some cases, the electron motion can become stochastic in the field of an MS wave with amplitudes below 1 nT. Regardless, if neither the bounce nor Landau resonance condition is satisfied initially, then the amplitude threshold of stochastic motion shows an increasing trend for lower frequencies and a decreasing trend for higher frequencies, even though the amplitude threshold is always very large(> 5 nT). Our study suggests that electron stochastic motion should also be considered when modeling electron dynamics regulated by intense MS waves in the Earth's magnetosphere.

Examination of Rainfall-Induced Landslide Failure Mechanisms via a Centrifuge Physical Simulation Test

Rainfall is one of the most important factors contributing to landslides, and gentle bedding incline, high-rainfall induced landslides are common throughout the world. Field observations and theoretical analyses have been used to assess slope instability caused by permeability variation. In this study, the influence of rainfall infiltration on gentle bedding incline slope behaviour was investigated using a centrifuge physical simulation test. The magnitude, pattern and development of pore water and earth pressure at the interface;the shear failure surface features;and the corresponding deformation and failure processes were considered. A model with interbedded sand and mud was created, and a centrifuge was used to simulate both natural and rainfall conditions. The weak intercalation was composed of single-material silty clay, and the landslide mass was composed of red-bed sandstone. A combination of photography, pore water pressure measurements and earth pressure measurements were used to examine the relationship between the pore water pressure, earth pressure and failure modes. When the slope experiences overall instability, the curves of the earth pressure and pore water pressure dramatically decrease. The results reveal that the failure shear surface largely depends on the differential creep caused by the properties of the rock mass and the rainfall infiltration.