The present study addresses the problem of fault estimation for a specific class of nonlinear time-varying complex networks,utilizing an unknown-input-observer approach within the framework of dynamic event-triggered ...The present study addresses the problem of fault estimation for a specific class of nonlinear time-varying complex networks,utilizing an unknown-input-observer approach within the framework of dynamic event-triggered mechanism(DETM).In order to optimize communication resource utilization,the DETM is employed to determine whether the current measurement data should be transmitted to the estimator or not.To guarantee a satisfactory estimation performance for the fault signal,an unknown-input-observer-based estimator is constructed to decouple the estimation error dynamics from the influence of fault signals.The aim of this paper is to find the suitable estimator parameters under the effects of DETM such that both the state estimates and fault estimates are confined within two sets of closed ellipsoid domains.The techniques of recursive matrix inequality are applied to derive sufficient conditions for the existence of the desired estimator,ensuring that the specified performance requirements are met under certain conditions.Then,the estimator gains are derived by minimizing the ellipsoid domain in the sense of trace and a recursive estimator parameter design algorithm is then provided.Finally,a numerical example is conducted to demonstrate the effectiveness of the designed estimator.展开更多
To date,there is still a lack of a comprehensive explanation for caged dynamics which is regarded as one of the intricate dynamic behaviors in amorphous alloys.This study focuses on Pd_(82)Si_(18)as the research objec...To date,there is still a lack of a comprehensive explanation for caged dynamics which is regarded as one of the intricate dynamic behaviors in amorphous alloys.This study focuses on Pd_(82)Si_(18)as the research object to further elucidate the underlying mechanism of caged dynamics from multiple perspectives,including the cage's lifetime,atomic local environment,and atomic potential energy.The results reveal that Si atoms exhibit a pronounced cage effect due to the hindrance of Pd atoms,resulting in an anomalous peak in the non-Gaussian parameters.An in-depth investigation was conducted on the caged dynamics differences between fast and slow Si atoms.In comparison to fast Si atoms,slow Si atoms were surrounded by more Pd atoms and occupied lower potential energy states,resulting in smaller diffusion displacements for the slow Si atoms.Concurrently,slow Si atoms tend to be in the centers of smaller clusters with coordination numbers of 9 and 10.During the isothermal relaxation process,clusters with coordination numbers 9 and 10 have longer lifetimes,suggesting that the escape of slow Si atoms from their cages is more challenging.The findings mentioned above hold significant implications for understanding the caged dynamics.展开更多
Internal effects of the dynamic behaviors and nonlinear characteristics of a coupled fractional order hydropower generation system(HGS) are analyzed. A mathematical model of hydro-turbine governing system(HTGS) with r...Internal effects of the dynamic behaviors and nonlinear characteristics of a coupled fractional order hydropower generation system(HGS) are analyzed. A mathematical model of hydro-turbine governing system(HTGS) with rigid water hammer and hydro-turbine generator unit(HTGU) with fractional order damping forces are proposed. Based on Lagrange equations, a coupled fractional order HGS is established. Considering the dynamic transfer coefficient eis variational during the operation, introduced e as a periodic excitation into the HGS. The internal relationship of the dynamic behaviors between HTGS and HTGU is analyzed under different parameter values and fractional order. The results show obvious fast–slow dynamic behaviors in the HGS, causing corresponding vibration of the system, and some remarkable evolution phenomena take place with the changing of the periodic excitation parameter values.展开更多
Using Reddy’s high-order shear theory for laminated plates and Hamilton’s principle, a nonlinear partial differential equation for the dynamics of a deploying cantilevered piezoelectric laminated composite plate, un...Using Reddy’s high-order shear theory for laminated plates and Hamilton’s principle, a nonlinear partial differential equation for the dynamics of a deploying cantilevered piezoelectric laminated composite plate, under the combined action of aerodynamic load and piezoelectric excitation, is introduced. Two-degree of freedom(DOF)nonlinear dynamic models for the time-varying coefficients describing the transverse vibration of the deploying laminate under the combined actions of a first-order aerodynamic force and piezoelectric excitation were obtained by selecting a suitable time-dependent modal function satisfying the displacement boundary conditions and applying second-order discretization using the Galerkin method. Using a numerical method, the time history curves of the deploying laminate were obtained, and its nonlinear dynamic characteristics,including extension speed and different piezoelectric excitations, were studied. The results suggest that the piezoelectric excitation has a clear effect on the change of the nonlinear dynamic characteristics of such piezoelectric laminated composite plates. The nonlinear vibration of the deploying cantilevered laminate can be effectively suppressed by choosing a suitable voltage and polarity.展开更多
It is a central issue to find the slow dynamic modes of biological macromolecules via analyzing the large-scale data of molecular dynamics simulation (MD). While the MD data are high-dimensional time-successive series...It is a central issue to find the slow dynamic modes of biological macromolecules via analyzing the large-scale data of molecular dynamics simulation (MD). While the MD data are high-dimensional time-successive series involving all-atomic details and sub-picosecond time resolution, a few collective variables which characterizing the motions in longer than nanoseconds are needed to be chosen for an intuitive understanding of the dynamics of the system. The trajectory map (TM) was presented in our previous works to provide an efficient method to find the low-dimensional slow dynamic collective-motion modes from high-dimensional time series. In this paper, we present a more straight understanding about the principle of TM via the slow-mode linear space of the conformational probability distribution functions of MD trajectories and more clearly discuss the relation between the TM and the current other similar methods in finding slow modes.展开更多
In this topic, a new. approach to the analysis of time-variation dynamics is proposed by use of Legendre series expansion and Legendre integral operator matrix. The theoretical basis for effective solution of time-var...In this topic, a new. approach to the analysis of time-variation dynamics is proposed by use of Legendre series expansion and Legendre integral operator matrix. The theoretical basis for effective solution of time-variation dynamics is therefore established, which is beneficial to further research of time-variation science.展开更多
Wind power has attracted increasing attention as a renewable and clean energy. Gear fault frequently occurs under extreme environment and complex loads. The time-varying meshing stiffness is one of the main excitation...Wind power has attracted increasing attention as a renewable and clean energy. Gear fault frequently occurs under extreme environment and complex loads. The time-varying meshing stiffness is one of the main excitations. This study proposes a 5 degree-of-freedom torsional vibration model for the planetary gear system. The influence of some parameters(e.g., contact ratio and phase difference) is discussed under different conditions of a single teeth pair and double pairs of teeth. The impact load caused by the teeth face fault, ramped load induced by the complex wind conditions, and the harmonic excitation are investigated. The analysis of the time-varying meshing stiffness and the dynamic meshing force shows that the dynamic design under different loads can be made to avoid resonance, can provide the basis for the gear fault location of a wind turbine, and distinguish the fault characteristics from the vibration signals.展开更多
Internal and external meshes are two of primary excitation sources which induce vibration while double-helical planetary gear sets are in transmission. Based on the analysis of tooth movement principle,three cases of ...Internal and external meshes are two of primary excitation sources which induce vibration while double-helical planetary gear sets are in transmission. Based on the analysis of tooth movement principle,three cases of mesh stiffness are derived via investigating the length of action lines,and catalogued in terms of β < β0,β = β0and β > β_0. The simulation demonstrates mesh stiffness between gear pairs performs as a trapezoid waveform( TW) and changes along with the line of action simultaneously,total mesh stiffness comes from the superposition of each engaged gear. While governing equations of motion contained 16 DOFs( degree of freedom) are constructed and effectively solved through the combination of numerical approaches. Comparing with sinusoidal waveform mesh stiffness( SW),the results show that dynamical factors and perturbation under the excitation of TW( β < β_0) are greater and remarkable than that from SW,with respect to the mean dynamic factors about 1. 51 and 1. 28,respectively. The fluctuation response between ring- planet( R- P) is stronger than sun-planet( S-P) which is also validated by both approach studies,frequency spectra analyses identifies larger distinct rotational resonance and more frequencies under TW excitation.展开更多
Based on Neumman series and epsilon-algorithm, an efficient computation for dynamic responses of systems with arbitrary time-varying characteristics is investigated. Avoiding the calculation for the inverses of the eq...Based on Neumman series and epsilon-algorithm, an efficient computation for dynamic responses of systems with arbitrary time-varying characteristics is investigated. Avoiding the calculation for the inverses of the equivalent stiffness matrices in each time step, the computation effort of the proposed method is reduced compared with the full analysis of Newmark method. The validity and applications of the proposed method are illustrated by a 4-DOF spring-mass system with periodical time-varying stiffness properties and a truss structure with arbitrary time-varying lumped mass. It shows that good approximate results can be obtained by the proposed method compared with the responses obtained by the full analysis of Newmark method.展开更多
This paper studies the stochastic synchronization problem for time-varying complex dynamical networks. This model is totally different from some existing network models. Based on the Lyapunov stability theory, inequal...This paper studies the stochastic synchronization problem for time-varying complex dynamical networks. This model is totally different from some existing network models. Based on the Lyapunov stability theory, inequality techniques, and the properties of the Weiner process, some controllers and adaptive laws are designed to ensure achieving stochastic synchronization of a complex dynamical network model. A sufficient synchronization condition is given to ensure that the proposed network model is mean-square stable. Theoretical analysis and numerical simulation fully verify the main results.展开更多
In current precision and ultraprecision machining practice,the positioning and control of actuation systems,such as slideways and spindles,are heavily dependent on the use of linear or rotary encoders.However,position...In current precision and ultraprecision machining practice,the positioning and control of actuation systems,such as slideways and spindles,are heavily dependent on the use of linear or rotary encoders.However,positioning control is passive because of the lack of direct monitoring and control of the tool and workpiece positions in the dynamic machining process and also because it is assumed that the machining system is rigid and the cutting dynamics are stable.In ultraprecision machining of freeform surfaces using slow tool servo mode in particular,however,account must be taken of the machining dynamics and dynamic synchronization of the cutting tool and workpiece positioning.The important question also arises as to how ultraprecision machining systems can be designed and developed to work better in this application scenario.In this paper,an innovative dynamics-oriented engineering approach is presented for ultraprecision machining of freeform surfaces using slow tool servo mode.The approach is focused on seamless integration of multibody dynamics,cutting forces,and machining dynamics,while targeting the positioning and control of the tool–workpiece loop in the machining system.The positioning and motion control between the cutting tool and workpiece surface are further studied in the presence of interfacial interactions at the tool tip and workpiece surface.The interfacial cutting physics and dynamics are likely to be at the core of in-process monitoring applicable to ultraprecision machining systems.The approach is illustrated using a virtual machining system developed and supported with simulations and experimental trials.Furthermore,the paper provides further explorations and discussion on implementation perspectives of the approach,in combination with case studies,as well as discussing its fundamental and industrial implications.展开更多
A conceptual model for microscopic-macroscopic slow-fast stochastic systems is considered. A dynamical reduction procedure is presented in order to extract effective dynamics for this kind of systems. Under appropriat...A conceptual model for microscopic-macroscopic slow-fast stochastic systems is considered. A dynamical reduction procedure is presented in order to extract effective dynamics for this kind of systems. Under appropriate assumptions, the effective system is shown to approximate the original system, in the sense of a probabilistic convergence.展开更多
Aimed at infinite horizon optimal control problems of discrete time-varying nonlinear systems,in this paper,a new iterative adaptive dynamic programming algorithm,which is the discrete-time time-varying policy iterati...Aimed at infinite horizon optimal control problems of discrete time-varying nonlinear systems,in this paper,a new iterative adaptive dynamic programming algorithm,which is the discrete-time time-varying policy iteration(DTTV)algorithm,is developed.The iterative control law is designed to update the iterative value function which approximates the index function of optimal performance.The admissibility of the iterative control law is analyzed.The results show that the iterative value function is non-increasingly convergent to the Bellman-equation optimal solution.To implement the algorithm,neural networks are employed and a new implementation structure is established,which avoids solving the generalized Bellman equation in each iteration.Finally,the optimal control laws for torsional pendulum and inverted pendulum systems are obtained by using the DTTV policy iteration algorithm,where the mass and pendulum bar length are permitted to be time-varying parameters.The effectiveness of the developed method is illustrated by numerical results and comparisons.展开更多
Bearings are key components in rotating machinery,which is widely used in many fields,such as CNC machines,wind turbines and induction machines.The increasingly harsh operation environment can lead to wear and tear on...Bearings are key components in rotating machinery,which is widely used in many fields,such as CNC machines,wind turbines and induction machines.The increasingly harsh operation environment can lead to wear and tear on raceways and reduce the precision and reliability of bearing or even machinery.Lubrication could relieve the wear to some degree,which is benefit to prolong the bearing’s life.Thus,investigation on the vibration responses under the influence of oil film is of great significance.However,for mechanism analysis,how to include the oil film into the bearing dynamic model affects the result and efficiency of solution.To address this problem,this study proposed a fast algorithm through load distribution and interpolation when calculating oil film stiffness and thickness during the solution of bearing vibration model.Analysis of oil film on vibration is carried out and a bearing test rig is designed to verify the proposed model.Numerical simulation result shows that rotational speed and load have vital effect on oil film and vibration.The experimental result is consistent with the simulation,which shows that the proposed model has a better performance on modeling bearing vibration and the method of considering oil film is reasonable.展开更多
A semi-analytical form of complex modal analysis is proposed for the time-variant dynamical problem of rotating pipe conveying fluid system.The complex mode superposition method is introduced for the dynamic analysis ...A semi-analytical form of complex modal analysis is proposed for the time-variant dynamical problem of rotating pipe conveying fluid system.The complex mode superposition method is introduced for the dynamic analysis in the time and frequency domains,in which appropriate orthogonality conditions are constructed to decouple the time-variant equation of motion.Consequently,complex frequencies and modes of vibration are analytically formulated and the variations of frequencies and damping of the system are evaluated.Numerical time-variant example of rotating pipe conveying fluid illustrates the effectiveness and accuracy of this method.Furthermore,the proposed solution scheme is also applicable to other similar time-variant dynamical problems.展开更多
In this paper, an impulsive control strategy is proposed for a class of nonlinear stochastic dynamical networks with time-varying delay. Using the Lyapunov stability theory, a sufficient verifiable criterion for the e...In this paper, an impulsive control strategy is proposed for a class of nonlinear stochastic dynamical networks with time-varying delay. Using the Lyapunov stability theory, a sufficient verifiable criterion for the exponential synchronization is derived analytically. Finally, a numerical simulation example is provided to verify the effectiveness of the proposed approach.展开更多
In recent years,subsynchronous resonance(SSR)has frequently occurred in DFIG-connected series-compensated systems.For the analysis and prevention,it is of great importance to achieve wide area monitoring of the incide...In recent years,subsynchronous resonance(SSR)has frequently occurred in DFIG-connected series-compensated systems.For the analysis and prevention,it is of great importance to achieve wide area monitoring of the incident.This paper presents a Hankel dynamic mode decomposition(DMD)method to identify SSR parameters using synchrophasor data.The basic idea is to employ the DMD technique to explore the subspace of Hankel matrices constructed by synchrophasors.It is analytically demonstrated that the subspace of these Hankel matrices is a combination of fundamental and SSR modes.Therefore,the SSR parameters can be calculated once the modal parameter is extracted.Compared with the existing method,the presented work has better dynamic performances as it requires much less data.Thus,it is more suitable for practical cases in which the SSR characteristics are timevarying.The effectiveness and superiority of the proposed method have been verified by both simulations and field data.展开更多
In order to implement the dynamic characteristic of a dual power-split transmission, a dynamic me- chanics model is built. Firstly, according to the method of theoretical analysis of the tooth contact analysis (TCA)...In order to implement the dynamic characteristic of a dual power-split transmission, a dynamic me- chanics model is built. Firstly, according to the method of theoretical analysis of the tooth contact analysis (TCA) and loaded tooth contact analysis (LTCA), the actual meshing process of each gear pairs is simulated, and the time-varying mesh stiffness excitations are obtained, which can improve the numerical precision. Second- ly, by using the lumped mass method, the bending-torsional coupling three dimensional dynamic model of the dual power-split transmission is established, and the identical dimensionless equations are deduced by elimina- ting the effect of rigid displacement and the method of dimensional normalization. Finally, by the method of the fourth order Runge-Kutta algorithm with variable step lengths, the responses of this system in a frequency domain and time domain are obtained, and the dynamic load change characteristics of each gear pairs are analyzed. The results show that the establishment, solution and analysis of the system dynamics model could provide a basis for the dynamic design, and have an important significance for the dynamic efficiency analysis and dynamic perform- ance optimization design of the dual power-split transmission.展开更多
基金supported in part by the National Natural Science Foundation of China (62233012,62273087)the Research Fund for the Taishan Scholar Project of Shandong Province of Chinathe Shanghai Pujiang Program of China (22PJ1400400)。
文摘The present study addresses the problem of fault estimation for a specific class of nonlinear time-varying complex networks,utilizing an unknown-input-observer approach within the framework of dynamic event-triggered mechanism(DETM).In order to optimize communication resource utilization,the DETM is employed to determine whether the current measurement data should be transmitted to the estimator or not.To guarantee a satisfactory estimation performance for the fault signal,an unknown-input-observer-based estimator is constructed to decouple the estimation error dynamics from the influence of fault signals.The aim of this paper is to find the suitable estimator parameters under the effects of DETM such that both the state estimates and fault estimates are confined within two sets of closed ellipsoid domains.The techniques of recursive matrix inequality are applied to derive sufficient conditions for the existence of the desired estimator,ensuring that the specified performance requirements are met under certain conditions.Then,the estimator gains are derived by minimizing the ellipsoid domain in the sense of trace and a recursive estimator parameter design algorithm is then provided.Finally,a numerical example is conducted to demonstrate the effectiveness of the designed estimator.
基金Project supported by the National Natural Science Foundation of China (Grant No.51701071)the Natural Science Foundation of Hunan Province,China (Grant Nos.2022JJ50115 and 2021JJ30179)the Research Foundation of the Education Bureau of Hunan Province,China (Grant No.22A0522)。
文摘To date,there is still a lack of a comprehensive explanation for caged dynamics which is regarded as one of the intricate dynamic behaviors in amorphous alloys.This study focuses on Pd_(82)Si_(18)as the research object to further elucidate the underlying mechanism of caged dynamics from multiple perspectives,including the cage's lifetime,atomic local environment,and atomic potential energy.The results reveal that Si atoms exhibit a pronounced cage effect due to the hindrance of Pd atoms,resulting in an anomalous peak in the non-Gaussian parameters.An in-depth investigation was conducted on the caged dynamics differences between fast and slow Si atoms.In comparison to fast Si atoms,slow Si atoms were surrounded by more Pd atoms and occupied lower potential energy states,resulting in smaller diffusion displacements for the slow Si atoms.Concurrently,slow Si atoms tend to be in the centers of smaller clusters with coordination numbers of 9 and 10.During the isothermal relaxation process,clusters with coordination numbers 9 and 10 have longer lifetimes,suggesting that the escape of slow Si atoms from their cages is more challenging.The findings mentioned above hold significant implications for understanding the caged dynamics.
基金Project supported by the National Natural Science Foundation of China for Outstanding Youth(Grant No.51622906)the National Natural Science Foundation of China(Grant No.51479173)+2 种基金the Fundamental Research Funds for the Central Universities(Grant No.201304030577)the Scientific Research Funds of Northwest A&F University(Grant No.2013BSJJ095)the Science Fund for Excellent Young Scholars from Northwest A&F University and Shaanxi Nova Program,China(Grant No.2016KJXX-55)
文摘Internal effects of the dynamic behaviors and nonlinear characteristics of a coupled fractional order hydropower generation system(HGS) are analyzed. A mathematical model of hydro-turbine governing system(HTGS) with rigid water hammer and hydro-turbine generator unit(HTGU) with fractional order damping forces are proposed. Based on Lagrange equations, a coupled fractional order HGS is established. Considering the dynamic transfer coefficient eis variational during the operation, introduced e as a periodic excitation into the HGS. The internal relationship of the dynamic behaviors between HTGS and HTGU is analyzed under different parameter values and fractional order. The results show obvious fast–slow dynamic behaviors in the HGS, causing corresponding vibration of the system, and some remarkable evolution phenomena take place with the changing of the periodic excitation parameter values.
基金supported by the National Natural Science Foundation of China (Grants 11402126, 11502122, and 11290152)the Scientific Research Foundation of the Inner Mongolia University of Technology (Grant ZD201410)
文摘Using Reddy’s high-order shear theory for laminated plates and Hamilton’s principle, a nonlinear partial differential equation for the dynamics of a deploying cantilevered piezoelectric laminated composite plate, under the combined action of aerodynamic load and piezoelectric excitation, is introduced. Two-degree of freedom(DOF)nonlinear dynamic models for the time-varying coefficients describing the transverse vibration of the deploying laminate under the combined actions of a first-order aerodynamic force and piezoelectric excitation were obtained by selecting a suitable time-dependent modal function satisfying the displacement boundary conditions and applying second-order discretization using the Galerkin method. Using a numerical method, the time history curves of the deploying laminate were obtained, and its nonlinear dynamic characteristics,including extension speed and different piezoelectric excitations, were studied. The results suggest that the piezoelectric excitation has a clear effect on the change of the nonlinear dynamic characteristics of such piezoelectric laminated composite plates. The nonlinear vibration of the deploying cantilevered laminate can be effectively suppressed by choosing a suitable voltage and polarity.
基金Project supported by the National Natural Science Foundation of China (Grant No. 11904086).
文摘It is a central issue to find the slow dynamic modes of biological macromolecules via analyzing the large-scale data of molecular dynamics simulation (MD). While the MD data are high-dimensional time-successive series involving all-atomic details and sub-picosecond time resolution, a few collective variables which characterizing the motions in longer than nanoseconds are needed to be chosen for an intuitive understanding of the dynamics of the system. The trajectory map (TM) was presented in our previous works to provide an efficient method to find the low-dimensional slow dynamic collective-motion modes from high-dimensional time series. In this paper, we present a more straight understanding about the principle of TM via the slow-mode linear space of the conformational probability distribution functions of MD trajectories and more clearly discuss the relation between the TM and the current other similar methods in finding slow modes.
文摘In this topic, a new. approach to the analysis of time-variation dynamics is proposed by use of Legendre series expansion and Legendre integral operator matrix. The theoretical basis for effective solution of time-variation dynamics is therefore established, which is beneficial to further research of time-variation science.
基金financially supported by the project‘Research on Key Technologies of Condition Monitoring and Intelligent Early Detection of Wind Turbine Based on Big Data’from State Grid Corporation of China(No.NYB17201600300)
文摘Wind power has attracted increasing attention as a renewable and clean energy. Gear fault frequently occurs under extreme environment and complex loads. The time-varying meshing stiffness is one of the main excitations. This study proposes a 5 degree-of-freedom torsional vibration model for the planetary gear system. The influence of some parameters(e.g., contact ratio and phase difference) is discussed under different conditions of a single teeth pair and double pairs of teeth. The impact load caused by the teeth face fault, ramped load induced by the complex wind conditions, and the harmonic excitation are investigated. The analysis of the time-varying meshing stiffness and the dynamic meshing force shows that the dynamic design under different loads can be made to avoid resonance, can provide the basis for the gear fault location of a wind turbine, and distinguish the fault characteristics from the vibration signals.
基金Sponsored by the National High-tech R&D Program of China(Grant No.2009AA04Z404)
文摘Internal and external meshes are two of primary excitation sources which induce vibration while double-helical planetary gear sets are in transmission. Based on the analysis of tooth movement principle,three cases of mesh stiffness are derived via investigating the length of action lines,and catalogued in terms of β < β0,β = β0and β > β_0. The simulation demonstrates mesh stiffness between gear pairs performs as a trapezoid waveform( TW) and changes along with the line of action simultaneously,total mesh stiffness comes from the superposition of each engaged gear. While governing equations of motion contained 16 DOFs( degree of freedom) are constructed and effectively solved through the combination of numerical approaches. Comparing with sinusoidal waveform mesh stiffness( SW),the results show that dynamical factors and perturbation under the excitation of TW( β < β_0) are greater and remarkable than that from SW,with respect to the mean dynamic factors about 1. 51 and 1. 28,respectively. The fluctuation response between ring- planet( R- P) is stronger than sun-planet( S-P) which is also validated by both approach studies,frequency spectra analyses identifies larger distinct rotational resonance and more frequencies under TW excitation.
基金supported by the Foundation of the Science and Technology of Jilin Province (20070541)985-Automotive Engineering of Jilin University and Innovation Fund for 985 Engineering of Jilin University (20080104).
文摘Based on Neumman series and epsilon-algorithm, an efficient computation for dynamic responses of systems with arbitrary time-varying characteristics is investigated. Avoiding the calculation for the inverses of the equivalent stiffness matrices in each time step, the computation effort of the proposed method is reduced compared with the full analysis of Newmark method. The validity and applications of the proposed method are illustrated by a 4-DOF spring-mass system with periodical time-varying stiffness properties and a truss structure with arbitrary time-varying lumped mass. It shows that good approximate results can be obtained by the proposed method compared with the responses obtained by the full analysis of Newmark method.
基金supported by the National Natural Science Foundation of China (Grant No.60974139)the Fundamental Research Funds for the Central Universities (Grant No.72103676)
文摘This paper studies the stochastic synchronization problem for time-varying complex dynamical networks. This model is totally different from some existing network models. Based on the Lyapunov stability theory, inequality techniques, and the properties of the Weiner process, some controllers and adaptive laws are designed to ensure achieving stochastic synchronization of a complex dynamical network model. A sufficient synchronization condition is given to ensure that the proposed network model is mean-square stable. Theoretical analysis and numerical simulation fully verify the main results.
基金The authors are grateful for Ph.D.Scholarship funding support from Brunel University London and the UKEPSRC.
文摘In current precision and ultraprecision machining practice,the positioning and control of actuation systems,such as slideways and spindles,are heavily dependent on the use of linear or rotary encoders.However,positioning control is passive because of the lack of direct monitoring and control of the tool and workpiece positions in the dynamic machining process and also because it is assumed that the machining system is rigid and the cutting dynamics are stable.In ultraprecision machining of freeform surfaces using slow tool servo mode in particular,however,account must be taken of the machining dynamics and dynamic synchronization of the cutting tool and workpiece positioning.The important question also arises as to how ultraprecision machining systems can be designed and developed to work better in this application scenario.In this paper,an innovative dynamics-oriented engineering approach is presented for ultraprecision machining of freeform surfaces using slow tool servo mode.The approach is focused on seamless integration of multibody dynamics,cutting forces,and machining dynamics,while targeting the positioning and control of the tool–workpiece loop in the machining system.The positioning and motion control between the cutting tool and workpiece surface are further studied in the presence of interfacial interactions at the tool tip and workpiece surface.The interfacial cutting physics and dynamics are likely to be at the core of in-process monitoring applicable to ultraprecision machining systems.The approach is illustrated using a virtual machining system developed and supported with simulations and experimental trials.Furthermore,the paper provides further explorations and discussion on implementation perspectives of the approach,in combination with case studies,as well as discussing its fundamental and industrial implications.
基金supported by NSF of China (10901065, 10971225, and11028102)the NSF Grants 1025422 and 0731201the Cheung Kong Scholars Program, and an open research grant from the State Key Laboratory for Nonlinear Mechanics at the Chinese Academy of Sciences
文摘A conceptual model for microscopic-macroscopic slow-fast stochastic systems is considered. A dynamical reduction procedure is presented in order to extract effective dynamics for this kind of systems. Under appropriate assumptions, the effective system is shown to approximate the original system, in the sense of a probabilistic convergence.
基金supported in part by Fundamental Research Funds for the Central Universities(2022JBZX024)in part by the National Natural Science Foundation of China(61872037,61273167)。
文摘Aimed at infinite horizon optimal control problems of discrete time-varying nonlinear systems,in this paper,a new iterative adaptive dynamic programming algorithm,which is the discrete-time time-varying policy iteration(DTTV)algorithm,is developed.The iterative control law is designed to update the iterative value function which approximates the index function of optimal performance.The admissibility of the iterative control law is analyzed.The results show that the iterative value function is non-increasingly convergent to the Bellman-equation optimal solution.To implement the algorithm,neural networks are employed and a new implementation structure is established,which avoids solving the generalized Bellman equation in each iteration.Finally,the optimal control laws for torsional pendulum and inverted pendulum systems are obtained by using the DTTV policy iteration algorithm,where the mass and pendulum bar length are permitted to be time-varying parameters.The effectiveness of the developed method is illustrated by numerical results and comparisons.
基金supported by Key Program of National Natural Science Foundation of China (52035002)National Natural Science Foundation of China (51805353).
文摘Bearings are key components in rotating machinery,which is widely used in many fields,such as CNC machines,wind turbines and induction machines.The increasingly harsh operation environment can lead to wear and tear on raceways and reduce the precision and reliability of bearing or even machinery.Lubrication could relieve the wear to some degree,which is benefit to prolong the bearing’s life.Thus,investigation on the vibration responses under the influence of oil film is of great significance.However,for mechanism analysis,how to include the oil film into the bearing dynamic model affects the result and efficiency of solution.To address this problem,this study proposed a fast algorithm through load distribution and interpolation when calculating oil film stiffness and thickness during the solution of bearing vibration model.Analysis of oil film on vibration is carried out and a bearing test rig is designed to verify the proposed model.Numerical simulation result shows that rotational speed and load have vital effect on oil film and vibration.The experimental result is consistent with the simulation,which shows that the proposed model has a better performance on modeling bearing vibration and the method of considering oil film is reasonable.
基金supported by National Natural Science Foundation of China(Project No.11572229)Shanghai Chenguang Plan(Project No.14CG18)Fundamental Research Funds for the Central Universities(Project No.22120180063).
文摘A semi-analytical form of complex modal analysis is proposed for the time-variant dynamical problem of rotating pipe conveying fluid system.The complex mode superposition method is introduced for the dynamic analysis in the time and frequency domains,in which appropriate orthogonality conditions are constructed to decouple the time-variant equation of motion.Consequently,complex frequencies and modes of vibration are analytically formulated and the variations of frequencies and damping of the system are evaluated.Numerical time-variant example of rotating pipe conveying fluid illustrates the effectiveness and accuracy of this method.Furthermore,the proposed solution scheme is also applicable to other similar time-variant dynamical problems.
文摘In this paper, an impulsive control strategy is proposed for a class of nonlinear stochastic dynamical networks with time-varying delay. Using the Lyapunov stability theory, a sufficient verifiable criterion for the exponential synchronization is derived analytically. Finally, a numerical simulation example is provided to verify the effectiveness of the proposed approach.
基金supported by the China Key Technology Research on Risk Perception of Sub-Synchronous Oscillation of Grid with Large-Scale New Energy Access SGTYHT/21-JS-223.
文摘In recent years,subsynchronous resonance(SSR)has frequently occurred in DFIG-connected series-compensated systems.For the analysis and prevention,it is of great importance to achieve wide area monitoring of the incident.This paper presents a Hankel dynamic mode decomposition(DMD)method to identify SSR parameters using synchrophasor data.The basic idea is to employ the DMD technique to explore the subspace of Hankel matrices constructed by synchrophasors.It is analytically demonstrated that the subspace of these Hankel matrices is a combination of fundamental and SSR modes.Therefore,the SSR parameters can be calculated once the modal parameter is extracted.Compared with the existing method,the presented work has better dynamic performances as it requires much less data.Thus,it is more suitable for practical cases in which the SSR characteristics are timevarying.The effectiveness and superiority of the proposed method have been verified by both simulations and field data.
基金supported by the Natural Science Foundation of China under Grant No.51175423
文摘In order to implement the dynamic characteristic of a dual power-split transmission, a dynamic me- chanics model is built. Firstly, according to the method of theoretical analysis of the tooth contact analysis (TCA) and loaded tooth contact analysis (LTCA), the actual meshing process of each gear pairs is simulated, and the time-varying mesh stiffness excitations are obtained, which can improve the numerical precision. Second- ly, by using the lumped mass method, the bending-torsional coupling three dimensional dynamic model of the dual power-split transmission is established, and the identical dimensionless equations are deduced by elimina- ting the effect of rigid displacement and the method of dimensional normalization. Finally, by the method of the fourth order Runge-Kutta algorithm with variable step lengths, the responses of this system in a frequency domain and time domain are obtained, and the dynamic load change characteristics of each gear pairs are analyzed. The results show that the establishment, solution and analysis of the system dynamics model could provide a basis for the dynamic design, and have an important significance for the dynamic efficiency analysis and dynamic perform- ance optimization design of the dual power-split transmission.