An internal ballistic model of electromagnetic railgun based on PFN coupled with multi-physical field and experimental validation

To accelerate the practicality of electromagnetic railguns,it is necessary to use a combination of threedimensional numerical simulation and experiments to study the mechanism of bore damage.In this paper,a three-dimensional numerical model of the augmented railgun with four parallel unconventional rails is introduced to simulate the internal ballistic process and realize the multi-physics field coupling calculation of the rail gun,and a test experiment of a medium-caliber electromagnetic launcher powered by pulse formation network(PFN)is carried out.Various test methods such as spectrometer,fiber grating and high-speed camera are used to test several parameters such as muzzle initial velocity,transient magnetic field strength and stress-strain of rail.Combining the simulation results and experimental data,the damage condition of the contact surface is analyzed.

Mussel-inspired PTW@PDA composites for developing high-energy gun propellants with reduced erosion and enhanced mechanical strength

The severe erosion and inadequate mechanical strength are prominent challenges for high-energy gun propellants.To address it,novel PTW@PDA composites was prepared by polydopamine(PDA)-modifying onto potassium titanate whisker(PTW,K_(2)Ti_(6)O_(13)),and after was incorporated into gun propellant as erosion-reducing and mechanical-reinforcing fillers.The interfacial characterizations results indicated that as-prepared PTW@PDA composites exhibits an enhanced surface compatible with propellant matrix,thereby facilitating their dispersion into propellants more effectively than raw PTW materials.Compared to original propellants,PTW@PDA-modified propellants exhibited significant less erosion,with a Ti-Kbased protective coating being detected on the eroded steel.And 0.5 wt%and 1.0 wt%addition of PTW@PDA significantly improved impact,compressive and tensile strength of propellants.Despite the inevitably reduction in relative force,PTW@PDA slightly increase propellant burning rate while exerting little adverse impact on propellant dynamic activity.This strategy can provide a promising alternative to develop high-energy gun propellant with less erosion and more mechanical strength.

Diagnostic utility of small-caliber and conventional endoscopes for gastric cancer and analysis of endoscopic false-negative gastric cancers

AIM: To analyze the diagnostic utility of a small-caliber endoscope(SC-E) and clinicopathological features of false-negative gastric cancers(FN-GCs). METHODS: A total of 21638 esophagogastroduodenoscopy(EGD) gastric cancer(GC) screening examinations were analyzed. Secondary endoscopic examinations(n = 3352) were excluded because most secondary examinations tended to be included in the conventional endoscopy(C-E) group. Detection rates of GCs and FN-GCs were compared between SC-E and C-E groups. FN-GC was defined as GC performed with EGD within the past 3 years without GC detection. Macroscopic types, histopathological characteristics and locations of FN-GCs were compared with firstly foundgastric cancers(FF-GCs) in detail. RESULTS: SC-E cases(n = 6657) and C-E cases(n = 11644), a total of 18301 cases, were analyzed. GCs were detected in 16(0.24%) SC-E cases and 40 C-E(0.34%) cases(P = 0.23) and there were 4 FN-GCs(0.06%) in SC-E and 13(0.11%) in C-E(P = 0.27), with no significant difference. FN-GCs/GCs ratio between SC-E and C-E groups was not significantly different(P = 0.75). The comparison of endoscopic macroscopic types of FN-GCs tended to be a less advanced type(P = 0.02). Histopathologically, 70.6% of FN-GCs were differentiated and 29.4% undifferentiated type. On the other hand, 43.0% of FF-GCs were differentiated and 53.8% undifferentiated type, so FN-GCs tended to be more differentiated type(P = 0.048). CONCLUSION: The diagnostic utility of SC-E for the detection of GCs and FN-GCs was not inferior to that of C-E. Careful observation for superficially depressed type lesions in the upper lesser curvature region is needed to decrease FN-GCs.

IN VIVO EFFECT OF HEPARIN PRETREATMENT OF SMALL-CALIBER DECELLULARIZED XENOGRAFT

Objective To develop a new vascular xenograft and to compare the in vivo behavior of thrombogenicity and intimal hyperplasia in the heparin-treated and the non-heparin-treated decellularized xenografts.Methods Canine common carotid arteries were decellularized by enzymatic and detergent extraction procedures.Then a part of decellularized vascular grafts were covalently linked with heparin.Xenografts with(n=24)and without(n=24)heparin treatment were implanted in rabbits' left and right carotid artery respectively as bypass grafts.Graft patency were checked by Duplex ultrasonography at 3 and 6 months after implantation.Twelve rabbits were euthanized randomly at 3 and 6 months respectively and bilateral grafts were explanted.Histological examination and immunohistochemical staining were performed to observe the vascular remodeling.The efficiency of heparin release was demonstrated with toluidine blue staining.HE staining and micrograph analysis system were used for valuating the intima hyperplasia(IH)of bilateral grafts.Results During implantation,thrombosis rate was 4% in the heparin-treated xenografts and 25% in the non-heparin-treated xenografts after 3 weeks(P<0.05).After 6 months,it was 8% versus 58% respectively(P<0.01).Both xenografts of two groups harvested at the end of 3 or 6 months showed a satisfactory cellular reconstruction of either smooth muscle cells or endothelial cells.Intimal hyperplasia in the heparin-treated vascular was less than in the non-heparin treated xenografts.In addition,intimal hyperplasia was liable to appear close to the proximal and distal anastomotic stoma.Toluidine blue staining demonstrated that heparin was slowly released during 6 months.Conclusion This study provides a new strategy to develop a small-caliber vascular xenograft through enzymatic-detergent extraction and heparin treatment.Heparin treatment of the decellularized xenograft is helpful for improving bypass graft patency and reducing intimal hyperplasia.If there was no thrombus,bilateral bypass grafts will undergo a vessel remodeling procedure.Canine common carotid artery treated by detergent and enzymatic extraction and heparin treatment may be used as a new small-caliber vascular xenograft.

One-step green method to prepare progressive burning gun propellant through gradient denitration strategy

Gradiently denitrated gun propellant(GDGP)prepared by a“gradient denitration”strategy is obviously superior in progressive burning performance to the traditional deterred gun propellant.Currently,the preparation of GDGP employed a tedious two-step method involving organic solvents,which hinders the large-scale preparation of GDGP.In this paper,GDGP was successfully prepared via a novelty and environmentally friendly one-step method.The obtained samples were characterized by FT-IR,Raman,SEM and XPS.The results showed that the content of nitrate groups gradiently increased from the surface to the core in the surface layer of GDGP and the surface layer of GDGP exhibited a higher compaction than that of raw gun propellant,with a well-preserved nitrocellulose structure.The denitration process enabled the propellant surface with regressive energy density and good progressive burning performance,as confirmed by oxygen bomb and closed bomb test.At the same time,the effects of different solvents on the component loss of propellant were compared.The result showed that water caused the least component loss.Finally,the stability of GDGP was confirmed by methyl-violet test.This work not only provided environmentally friendly,simple and economic preparation of GDGP,but also confirmed the stability of GDGP prepared by this method.

Development and simulation of a gridded thermionic cathode electron gun for a high-energy photon source

A gridded thermionic cathode electron gun was developed for the linear accelerator of the High Energy Photon Source(HEPS).An electron gun should provide a large maximum bunch charge with a wide adjustable range.To satisfy these requirements,the shape of the electrode was optimized using a multi-objective genetic algorithm.A large bunch charge with an adjustable range was achieved using the grid-limited gun,the flow of which was analyzed using 3-D simulations.The electron gun has been manufactured and tested,and the measured data of the grid-limited current and simulation results are compared and discussed in this study.

Effect of swirling flow on platelet concentration distribution in small-caliber artificial grafts and end-to-end anastomoses

Platelet concentration near the blood vessel wall is one of the major factors in the adhesion of platelets to the wall.In our previous studies,it was found that swirling flows could suppress platelet adhesion in small-caliber artificial grafts and end-to-end anastomoses.In order to better understand the beneficial effect of the swirling flow,we numerically analyzed the near-wall concentration distribution of platelets in a straight tube and a sudden tubular expansion tube under both swirling flow and normal flow conditions.The numerical models were created based on our previous experimental studies.The simulation results revealed that when compared with the normal flow,the swirling flow could significantly reduce the near-wall concentration of platelets in both the straight tube and the expansion tube.The present numerical study therefore indicates that the reduction in platelet adhesion under swirling flow conditions in small-caliber arterial grafts,or in end-to-end anastomoses as observed in our previous experimental study,was possibly through a mechanism of platelet transport,in which the swirling flow reduced the near-wall concentration of platelets.

Analysis of Corrosion Mechanisms of Low-cement or No-cement Al_(2)O_(3)-MgO Gunning Mix with Special Calcined Alumina in Rotary Slag Test

Al_(2)O_(3)-MgO and Al_(2)O_(3)-spinel low cement castables(LCC-AM and LCC-AS)have been extensively used in steel ladles as working linings.Nevertheless,the use of alumina-magnesia gunning mixes has been mainly kept for maintaining these castable linings,because of high rebound loss,poor green strength,high porosity and short life-span.Thanks to a high BET alumina(MC-G),it is now possible to develop a series of high-performance no-cement or low-cement Al_(2)O_(3)-MgO gunning mixes(NCG-AM or LCG-AM).The paper focuses on the BOF slag resistance of NCG-AM,LCG-AM,LCC-AM and LCC-AS.The corrosion mechanisms of rotary slag samples were studied by scanning electron microscopy(SEM/EDS).The results reveal different microstructures around MgO particles,depending on the four used compositions.Continuous and thicker spinel phases were formed in NCG-AM,which was proved to have the best corrosion resistance after the dynamic slag test.MC-G can provide a high diffusion flux of Al^(3+)in terms of kinetics and hence inhibits Kirkendall porosity around MgO particles.In addition,a continuous spinel phase acts like a pinning nail to reinforce the matrix and thus decreases erosion by slag.In contrast to NCG-AM,the porous spinel phase was found around unreacted MgO particles and some particles were carried away near the interface of LCC-AM and slag.The NCG-AM containing MC-G had been tested in two steel plants,and it extended the service life of the ladles up to 50%.In addition,this study suggests the potential application of NCG-AM as steel ladle linings.

主成分分析和灰色模型组合的身管多点烧蚀磨损量预测

身管是火炮类武器的关键零件,对其烧蚀磨损量进行预测,有助于保持火炮作战效能。针对火炮身管沿轴向各点烧蚀磨损量需分别建立数学模型进行预测问题,提出一种组合烧蚀磨损量预测方法。采用主成分分析(principal component analysis,PCA)方法对身管多点烧蚀磨损量进行数据空间降维,提取反映烧蚀磨损量变化的主成分,利用灰色模型对主成分进行多步预测,通过PCA逆运算获得身管内膛多点烧蚀磨损量预测值。结果表明,在历史数据较少的条件下,通过选择合适的预测步数可获得较为准确的预测值,为身管内膛多点烧蚀磨损量的预测提供了一种新的有效途径。

基于射击时机的坦克射击门分析及改进

针对坦克的射击门控制逻辑,分析现有射击门在坦克高速行进条件下在射击时机判断上的不足,提出基于预测机制的射击门改进方法,该射击门在考虑射击时延和炮口切向速度影响的情况下,去除了身管必须满足进入简单射击门的角度约束,可更大限度地把握有效射击时机,数字仿真结果验证了改进射击门的优越性。

枪管用环保镀层摩擦行为研究

传统枪管内膛表面采用的六价铬镀层,高温耐磨性好,但对环境污染严重。为开发环保镀层,采用超景深三维显微镜、扫描电子显微镜表征了室温和高温(400℃)摩擦磨损试样,对比分析了六价铬、三价铬、钴-镍和镍-钨四种电镀层的磨损特征。研究结果表明:在500℃定性回火后,三价铬、镍-钨、六价铬和钴-镍镀层硬度依次递减,与六价铬层相比,三价铬层脆性大,镍-钨和钴-镍镀层韧性高;室温下与H62黄铜对摩后,六价铬和三价铬镀层摩擦程度较轻,钴-镍和镍-钨镀层呈现明显粘着特征,二者摩擦系数高于两种铬层;400℃下与08Al钢对摩后,六价铬呈粘着磨损特征,摩擦程度较大;三价铬层摩擦系数相对较高;镍-钨镀层呈磨粒磨损特征,摩擦系数与六价铬接近,摩擦程度相对较轻。

一种民用无人机反制系统的设计

本文设计了一种民用无人机反制系统,用于保护重点区域的低空空域安全。系统基于软件无线电理念设计:软件平台使用GUN Radio,硬件平台使用Hack RF。文章分析了驱离迫降民用无人机的原理,详细阐述了模拟GPS信号和产生宽带噪声信号的方法,通过理论计算推断系统的输出功率,系统理论上可对100 m范围内的民用无人机进行反制。经验证,系统可实现对无人机的驱离迫降,达到反制效果。系统方案简洁、成本低,可推广至类似的项目研究领域,具有较高的研究价值。

武器装备轻量化结构正向设计方法及应用

为满足武器装备轻量化的迫切需求,提升装备结构优化设计水平,提出了一种代理模型辅助多目标优化的结构正向设计方法。按照从概念设计到参数优化设计的流程,通过优化信息交互和代理模型重构来实现结构多目标优化设计。以轻型车载高炮弹箱架优化设计为例,首先,根据拓扑优化获得的最佳传力路径,建立几何模型和有限元分析模型。其次,通过灵敏度分析缩减设计变量,建立以一阶模态频率和结构强度为约束、最小化质量和最大化刚度为目标的优化模型。然后,使用差分进化算法求解基于Kriging模型的多目标优化问题;在优化过程中,通过比较中间优化结果调整优化模型,并采用基于期望改进的填充样本策略重构代理模型。最后,兼顾结构轻量化和安全,筛选44组优化解中的3组优势方案与初始设计进行比较,结果显示:在满足弹箱架结构性能的前提下,重量分别可减轻31.2%、24.7%和21.8%;所提结构正向设计方法能够明显提升轻量化效果,也可为相关结构优化设计提供参考。

多重约束下民警公务用枪的行动逻辑

公务用枪中存在的问题反映出公安机关在社会治理中的困境。实证研究发现,民警公务用枪的心理与行为受到多重条件的约束。文化与舆论是最外围的软性约束,影响着公务用枪的正义感。法律法规是较外围的刚性约束,决定着公务用枪的合法感。组织氛围是较内围的显性约束,决定着公务用枪的支持感。素质与训练则是最内围的硬性约束,决定着公务用枪的效能感。四个维度的用枪心理影响着民警在警务实战中的行为倾向和行为表现。涉枪事件的应对和涉枪民警的处理,又将反作用于涉枪民警及其他民警的心理与行为。研究结果为民警不愿拿枪、不敢用枪、不会用枪等问题找到一种阐释框架。

炮膛间距对枢轨初始接触状态的影响分析

电磁轨道炮炮膛间距直接影响到发射过程中枢轨滑动电接触状态,尤其是起始段炮膛间距变化对电枢烧蚀具有较大影响,将炮膛等效成呈一定角度张开的两条直线,利用角平分线相关特性开展炮膛间距测量,根据炮膛间距实测数据,结合工程实际分析起始段炮膛变化形态并建立对应形态下的枢轨初始接触模型,分析了炮膛装配精度对枢轨初始接触性能的影响,分析结果表明起始段炮膛间距是造成电枢静态受力不均、枢轨接触面积及接触力非对称分布的主要原因,通过不同炮膛变化形态的静态接触试验,进一步验证了理论分析结果。通过分析炮膛间距对枢轨初始接触的影响作用,为枢轨匹配性设计提供理论依据。

筋膜枪与拉伸放松改善运动性肌肉疲劳的比较

背景:利用科技手段促进运动后肌肉疲劳恢复的方法逐渐增多,如振动泡沫轴、筋膜枪放松、超低温冷疗等,其中筋膜枪放松在实践中已广泛使用,但是目前国内外对于筋膜枪的研究还较少。目的:比较筋膜枪、拉伸、筋膜枪+拉伸3种放松方式对运动性肌肉疲劳恢复过程中肌肉状态、肌肉力量的影响,为3种方法的实践应用提供科学依据。方法:40名大学生随机分为对照组(10名)、拉伸组(10名)、筋膜枪组(10名)、筋膜枪+拉伸组(10名)。所有受试者完成每组15次的腿屈伸训练,强度为60%1 RM,进行10组运动性疲劳造模,随后分别采用仰卧休息、静态拉伸、筋膜枪放松、筋膜枪+拉伸放松进行干预,且在训练前、训练后即刻、放松后即刻、运动后24 h及48 h进行肌肉状态、肌肉力量指标测试。结果与结论:①放松后即刻对照组、拉伸组的肌肉张力、动态硬度显著高于训练前(P<0.01),筋膜枪、筋膜枪+拉伸组与训练前相比差异无显著性意义(P>0.05);②训练后24 h对照组、筋膜枪组的峰力矩显著低于训练前(P<0.01),拉伸组、筋膜枪+拉伸组24 h后与训练前比较差异无显著性意义(P>0.05);③结果说明,筋膜枪能够即刻有效改善运动性疲劳的肌肉状态,拉伸能够促进运动性疲劳后肌肉力量在24 h内得到有效恢复,筋膜枪与拉伸结合的放松手段能够实现两种效果的叠加。

基于生成对抗网络数据增强的舰炮可靠性分析

舰炮故障数据不足会导致其可靠性分析变得极其困难。为解决故障数据不足这一问题,采用生成式对抗网络(generative adversarial network,GAN)对故障样本进行数据增强。建立GAN数据增强深度神经网络的舰炮可靠性分析模型,并与原始数据进行可靠性分析获得的指标进行了对比。结果表明,利用GAN数据增强后的扩充样本得到的指数分布拟合精度及威布尔分布拟合精度分别提高了5.40%和11.90%,相较于原始数据有了显著提升。为实现舰炮故障数据可靠性分析提供了方法和思路。

15-15hs Max材料枪钻加工的钻削力和切屑分析

高氮奥氏体不锈钢15-15hs Max具有优秀的耐蚀性、良好的综合力学性能,但切削加工性差,属于一种难加工材料。以某石油钻探部件为研究对象,对15-15hs Max的加工特性进行分析,通过对15-15hs Max钻削过程的有限元仿真,分析其加工过程中的钻削力和切屑形态的变化。仿真结果表明:钻削力会随着钻入深度的增加而增加,当切削刃全部参与切削时钻削力达到稳定,加工过程中形成的切屑为向上弯曲的螺旋状切屑。在保证加工孔质量及加工效率条件下,得出了一组较为合理的钻削参数。

雾炮风机的气动性能分析与结构改进

为提高ZWP-80型雾炮风机的降尘性能,解决有效射程短、覆盖面积小和降尘效果差等问题,使用ANSYS中的Fluent模块对雾炮工作过程进行仿真,得到了雾炮内部和外部流场的流动状态以及相应的数据。基于仿真结果,对雾炮风机的风筒出口直径和风筒长度进行优化改进和参数匹配。利用单因素实验和正交实验确定ZWP-80型雾炮最佳的结构参数优化方案和最佳设计方案,提高其降尘性能。

定射角射孔工艺在大位移定向井中的应用与实践

通过对萨中开发区112#断层区块构造特征和开发井网情况的深入研究,部署距离断层50 m平行断层面钻井的大位移定向井。考虑射孔油层保护要求,结合定射角射孔工艺原理,确定射孔工艺、射孔输送方式及匹配的射孔枪、弹等射孔参数,选用合理的射孔液,采用负压射孔工艺、确定合理负压值,保证了定射角射孔工艺效果。实现了单井日增液17.6 t,日增油4.2 t,年节电约2.56×10^(4) kWh,创造较好的经济效益,保证了油田开发效果。