In-situ Si particle-reinforced joints of hypereutectic Al−60Si alloys by ultrasonic-assisted soldering

To improve the wettability of hypereutectic Al−60Si alloy and enhance the mechanical properties of the joints,Al−60Si alloy was joined by ultrasonic soldering with Sn-9Zn solder,and a sound joint with in-situ Si particle reinforcement was obtained.The oxide film of Al−60Si alloy at the interface was identified by transmission electron microscopy(TEM)analysis as amorphous Al_(2)O_(3).The oxide of Si particles in the base metal was also alumina.The oxide film of Al−60Si alloy was observed to be removed by ultrasonic vibration instead of holding treatment.Si particle-reinforced joints(35.7 vol.%)were obtained by increasing the ultrasonication time.The maximum shear strength peaked at 99.5 MPa for soldering at 330℃with an ultrasonic vibration time of 50 s.A model of forming of Si particles reinforced joint under the ultrasound was proposed,and ultrasonic vibration was considered to promote the dissolution of Al and migration of Si particles.

Recycling of metals from waste Sn-based alloys by vacuum separation

In order to recycle waste Sn-based alloys, the vapor-liquid phase equilibrium composition diagrams of Sn-Pb, Sn-Sb and Sn-Zn binary systems were calculated. The calculated results indicate that Pb, Sb and Zn can be separated from Sn effectively. Based on the above calculation, the industrial experiments of vacuum distillation of Sn-Pb alloy, Sn-Pb-Sb alloy, Sn-Pb-Sb-As alloy, crude Sn and Sn-Zn alloy with different contents were carried out. The experimental results show that Pb(>99% Pb) and Sn(≤0.003% Pb) were obtained simultaneously while Sn-Pb alloy was subjected to vacuum distillation; the crude Sn(>90% Sn, ≤ 2% Pb, ≤6% Sb) and crude Pb(≤2% Sn) were obtained simultaneously while a single vacuum distillation was carried out for Sn-Pb-Sb alloy; the Pb and Bi contents in the Sn ingot(99.99% Sn) achieve the grade A of GB/T 728—2010 standard, more than 50% of As and Sb was removed after vacuum distillation of crude Sn; Zn(<0.002% Sn) and Sn(about 3% Zn) were obtained while vacuum distillation of Sn-Zn alloy was conducted at 1173 K, 20-30 Pa for 8-10 h.

A comprehensive review of radiation effects on solder alloys and solder joints

In the realm of military and defence applications, exposure to radiation significantly challenges the performance and reliability of solder alloys and joints in electronic systems. This comprehensive review examines radiation-induced effects on solder alloys and solder joints in terms of microstructure and mechanical properties. In this paper, we evaluate the existing literature, including experimental studies and fundamental theory, to provide a comprehensive overview of the behavior of solder materials under radiation. A review of the literature highlights key mechanisms that contribute to radiation-induced changes in the microstructure, such as the formation of intermetallic compounds, grain growth,micro-voids and micro-cracks. Radiation is explored as a factor influencing solder alloy hardness,strength, fatigue and ductility. Moreover, the review addresses the challenges and limitations inherent in studying the effects of radiation on solder materials and offers recommendations for future research. It is crucial to understand radiation-induced effects on solder performance to design robust and radiationresistant electronic systems. A review of radiation effects on solder materials and their applications in electronics serves as a valuable resource for researchers, engineers, and practitioners in that field.

Microstructure evolution and mechanical properties of ultrasonic-assisted soldering joints of 2024 aluminum alloys

Ultrasonic-assisted soldering of 2024 aluminum alloys using a filler metal of Zn-5Al alloy was investigated at the temperature of 400 ℃,which is lower than the solution strengthening temperature of Al-Cu alloys.The ultrasonic vibration with power of 200 W and vibration amplitude of 15 μm at the frequency of 21 kHz was applied on the top samples.The ultrasonic vibration promoted the dissolution of Al elements in the base metal.The reduction of volume fraction of the eutectic phases in the bonds was investigated by increasing ultrasonic vibration time.As the ultrasonic vibration time increased from 3 s to 30 s,the volume fraction of the eutectic phase in the bonds decreased from 12.9% to 0.9%,and the shear strength of the joints was up to 149-153 MPa,increased by 20%.The improvement of the mechanical properties of joints was discussed based on the modulus and hardness of the phases in the bonds and the fracture of the joints.

Combined effects of Bi and Sb elements on microstructure,thermal and mechanical properties of Sn−0.7Ag−0.5Cu solder alloys

This research investigated the combined effects of addition of Bi and Sb elements on the microstructure,thermal properties,ultimate tensile strength,ductility,and hardness of Sn−0.7Ag−0.5Cu(SAC0705)solder alloys.The results indicated that the addition of Bi and Sb significantly reduced the undercooling of solders,refined theβ-Sn phase and extended the eutectic areas of the solders.Moreover,the formation of SbSn and Bi phases in the solder matrix affected the mechanical properties of the solder.With the addition of 3 wt.%Bi and 3 wt.%Sb,the ultimate tensile strength and hardness of the SAC0705 base alloy increased from 31.26 MPa and 15.07 HV to 63.15 MPa and 23.68 HV,respectively.Ductility decreased due to grain boundary strengthening,solid solution strengthening,and precipitation strengthening effects,and the change in the fracture mechanism of the solder alloys.

Influence of cobalt content on microstructure and corrosionperformance of extruded Sn-9Zn solder alloys

The Pb-free solders have attracted a great deal of attention recently due to the environmental concerns.The present work focuses on the effect of cobalt content(0,0.5 and 3.0)on the microstructural characteristics,melting point and corrosion performance of extruded Sn-9Zn solder alloys.The results reveal that the Zn-rich precipitates with spherical or needle-like shape in the Sn-9Zn-xCo alloys are refined remarkably by forming the γ-Co5Zn21 and Co2Sn2Zn Co-contained intermetallic compounds,though the melting point and eutectic reaction temperature decrease slightly.It is suggested that the corrosion property of the extruded Sn-9Zn-xCo alloys is improved significantly by adding the cobalt element,while the content should be controlled reasonably.Combining the corrosion morphology,the influence of cobalt content on the corrosion behavior of the Sn-9Zn-xCo alloys is analyzed in terms of the refined microstructure and the enhanced passive film stability.

Effect of cerium on microstructure and mechanical properties of Sn-Ag-Cu system lead-free solder alloys

The melting point, spreading property, mechanical properties and microstructures of Sn-3.0Ag-2.8Cu solder alloys added with micro-variable-Ce were studied by means of optical microscopy, scanning electron microscopy(SEM) and energy dispersive X-ray(EDX). The results indicate that the melting point of Sn-3.0Ag-2.8Cu solder is enhanced by Ce addition; a small amount of Ce will remarkably prolong the creep-rupture life of Sn-3.0Ag-2.8Cu solder joint at room temperature, especially when the content of Ce is 0.1%, the creep-rupture life will be 9 times or more than that of the solder joint without Ce addition; the elongation of Sn-3.0Ag-2.8Cu solder is also obviously improved even up to 15.7%. In sum, the optimum content of Ce is within 0.05%-0.1 %.

Effect of Ag and Ni on the melting point and solderability of SnSbCu solder alloys

To improve the properties of Sn10Sb8Cu solder alloy, two new solders （SnSbCuAg and SnSbCuNi） were formed by adding small amounts of Ag or Ni into the solder alloy. The results show that the melting point of the SnSbCuAg solder alloy decreases by 14.1℃ and the spreading area increases by 16.5% compared to the matrix solder. The melting point of the SnSbCuNi solder alloy decreases by 5.4℃ and the spreading area is slightly less than that of the matrix solder. Microstructure analysis shows that adding trace Ag makes the melting point decline due to the dispersed distribution of SnAg phase with low melting point. Adding trace Ni, Cu6Sn5 and （Cu, Ni）6Sn5 with polyhedron shape on the copper substrate can be easily seen in the SnSbCuNi solder alloy, which makes the viscosity of the melting solder increase and the spreading property of the solder decline.

Solderability of Electrodeposited Fe-Ni Alloys with Eutectic SnAgCu Solder

Solderabilities of electrodeposited Fe-Ni alloys with SnAgCu solder were examined by wetting balance measurements and compared to those of pure Ni and pure Fe platings. Excellent solderability was found on the Ni-52Fe plating as both the wetting force and kinetics approached or exceeded those on the pure Ni. However, upon further increase in Fe content to 75 at. pct, the solderability of the alloy was severely degraded even though it was still better than that of the pure Fe plating. X-ray photoelectron spectroscopy showed that such a strong dependence of solderability on Fe content is related to the much thinner, incomplete oxide coverage of Ni-rich plating surface.

Microstructures and properties of Sn-Ag-Cu lead-free solder alloys containing La

Trace amounts of La were utilized to improve the melting behaviors,microstructures,tensile properties and microhardness of Sn-3.0Ag-0.5Cu lead-free solder alloy. La has little effect on the melting behavior of Sn-3.0Ag-0.5Cu alloy according to the differential thermal analysis(DTA) tests. The X-ray diffraction(XRD) patterns show that β-Sn,Ag3Sn and Cu6Sn5 coexist in the as-cast solder alloys and LaSn3 phases emerge when adding 0.4% La. The microstructures modified by La are more uniform and much finer than that of baseline alloy,and the coarse LaSn3 particles with complex dendrites are observed by optical microscopy(OM) and scanning electron microscopy(SEM) when the addition of La is up to 0.4%. The composition of the LaSn3 phases is identified by energy-dispersive spectroscopy(EDS). There are considerable improvements in mechanical properties with 0.05% and 0.1% addition,but degenerations by adding 0.4%La. The Vickers microhardness of β-Sn and eutectic area are both enhanced with the addition of La and the microhardness of LaSn3 is much larger than those of β-Sn and eutectic area.

Thermal and Electrical Properties of Sn-Zn-Bi Ternary Soldering Alloys

Sn-Zn based solder is a possible replacement of Pb solder because of its better mechanical properties. The alloys need to be studied and explored to get a usable solder alloy having better properties. In this work, eutectic Sn-9Zn and three Tin-Zinc-Bismuth ternary alloys were prepared and investigated their thermal and electrical properties. Thermo-mechanical Analysis and Differential Thermal Analysis were used to investigate thermal properties. Microstructural study is carried out with Scanning Electron Microscope. The alloys have single melting point. The co-efficient of thermal expansion and co-efficient of thermal contraction varies with alloy composition and temperature range. Electrical conductivity changes with Bi addition.

Effect of Sb content on properties of Sn-Bi solders

The effect of Sb content on the properties of Sn-Bi solders was studied. The nonequilibrium melting behaviors of a series of Sn-Bi-Sb solders were examined by differential scanning calorimetry （DSC）. The spreading test was carried out to characterize the wettability of Sn-Bi-Sb solders on Cu substrate. The mechanical properties of the solders/Cu joints were evaluated. The results show that the ternary alloy solders contain eutectic structure resulting from quasi-peritetic reaction. With the increase of Sb content, the amount of the eutectic structure increases. At a heating rate of 5 ℃/min, Sn-Bi-Sb alloys exhibit a higher melting point and a wider melting range. A small amount of Sb has an impact on the wettability of Sn-Bi solders. The reaction layers form during spreading process. Sb is detected in the reaction layer while Bi is not detected. The total thickness of reaction layer between solder and Cu increases with the increase of the Sb content. The shear strength of the Sn-Bi-Sb solders increases as the Sb content increases.

EFFECTS OF RARE EARTH ELEMENT LANTHANUM ON MICROSTRUCTURE AND PROPERTIES OF Ag-Cu-Ti SOLDER ALLOY

The effects of rare earth Lanthanum on the microstructure, the physical property and the microhardness of Ag-Cu-Ti solder alloy are studied. Experimental results indicate that the addition of Lanthanum can evidently improve the wettability and the microhardness of Ag-Cu-Ti solder alloy. Analysis results show that the increase in microhardness is related to the refining and uniform distribution of the intermetallic compounds. Proper content of Lanthanum added in Ag-Cu-Ti alloy solder can be controlled below 0.5% in mass percent.

Effects of rare earth La on the microstructure and melting property of(Ag-Cu_(28))-30Sn alloys prepared by mechanical alloying

To obtain novel intermediate temperature alloy solders with a melting temperature of 400-600°C,nominal（Ag-Cu28）-30Sn alloys without or with a trace addition（0.5 or 1.0 wt.%） of rare earth（RE） element La were prepared by mechanical alloying.The aim of this research is to investigate the effects of the addition of La on the microstructures,alloying process and melting properties of（Ag-Cu28）-30Sn alloys.The results show that the addition of La produces no new phase.A trace amount of La addition can effectively refine the grain size,but the excessive addition of 1.0 wt.% La inhibits the alloying process.The influence of La on the melting temperatures of solder alloys is negligible.However,the trace addition of 0.5 wt.% La can distinctly reduce the fusion zone and improve the melting property of（Ag-Cu28）-30Sn alloys.

Preparation and Properties of Particle Reinforced Sn-Zn-based Composite Solder

Particle reinforced Sn-Zn based composite solders were obtained by adding Cu powders to Sn-9Zn melts. The microstructure analysis reveals that in situ CusZn8 particles are formed and distributed uniformly in the composite solders. The strength and plasticity of the composite solders were improved, and creep resistance was considerably enhanced. The wettability of these composite solders is also better than that of Sn-9Zn.

Effect of indium addition on the microstructural formation and soldered interfaces of Sn-2.5Bi-1Zn-0.3Ag lead-free solder

The microstructural formation and properties of Sn-2.5Bi-xln-lZn-0.3Ag （in wt%） alloys and the evolution of soldered interfaces on a Cu substrate were investigated. Apart from the relatively low melting point （about 195C）, which is close to that of conventional eutectic Sn-Pb solder, the investigated solder presents superior wettability, solderability, and ductility. The refined equiaxial grains enhance the me- chanical properties, and the embedded bulk intermetallic compounds （IMCs） （Cu6Sn5 and CusZns） and granular Bi particles improve the joint reliability. The addition of In reduces the solubility of Zn in the 13-Sn matrix and strongly influences the separation and growth behaviors of the IMCs. The soldered interface of Sn-2.5Bi-xln-lZn-0.3Ag/Cu consists of Cu-Zn and Cu-Sn IMC layers.

Microstructure evolution and mechanical properties of the Sip/Zn- Al composite joints by ultrasonic-assisted soldering in air

Hypereutectic Al -27Si alloys were joined without flux by ultrasonic-assisted soldering at 420 ℃ in air using Zn -5Al the filler alloys, and Si particulate-reinforced Zn - Al based composites filler joints were obtained. The ultrasonic vibration introduced into soldering could influence the migration of Si particles and the microstructure of solidified Zn - Al based alloys. Both the distribution of Si particles and microstructure of the solidified Zn - Al based alloys affected the shear strength of joints. The shear strength increased with the ultrasonic vibration time. The highest average shear strength of joints reached to -68.5 MPa. Transcrystalline rupture mode was observed on the fracture surface.

Influence of bismuth on microstructure,thermal properties,mechanical performance,and interfacial behavior of SAC305−xBiCu solder joints

This research sought to improve the properties of SAC305 solder joints by the addition of 1 and 2 wt.%Bi.The effects of bismuth doping on the microstructure,thermal properties,and mechanical performance of the SAC305−xBiCu solder joints were investigated.Bi-doping modified the microstructure of the solder joints by refining the primaryβ-Sn and eutectic phases.Bi-doping below 2 wt.%dissolved in theβ-Sn matrix and formed a solid solution,whereas Bi additions equal to or greater than 2 wt.%formed Bi precipitates in theβ-Sn matrix.Solid solution strengthening and precipitation strengthening mechanisms in theβ-Sn matrix increased the ultimate tensile strength and microhardness of the alloy from 35.7 MPa and 12.6 HV to 55.3 MPa and 20.8 HV,respectively,but elongation decreased from 24.6%to 16.1%.The fracture surface of a solder joint containing 2 wt.%Bi was typical of a brittle failure rather than a ductile failure.The interfacial layer of all solder joints comprised two parallel IMC layers:a layer of Cu6Sn5 and a layer of Cu3Sn.The interfacial layer was thinner and the shear strength was greater in SAC305−xBiCu joints than in SAC305Cu solder joints.Therefore,small addition of Bi refined microstructure,reduced melting temperature and improved the mechanical performance of SAC305Cu solder joints.

Property alterations of Sn-0.6Cu-0.05Ni-Ge lead-free solder by Ag, Bi, In and Sb addition

The Sn-Cu-Ni-Ge solder is a strong challenger to the Sn-Ag-Cu（SAC） solders as a replacement for the Sn-Pb eutectic solder. This research investigated the effects of addition of Ag, Bi, In, and Sb on the physical properties of the Sn-0.6 Cu-0.05 Ni-Ge（SCNG） lead-free solder and the interfacial reaction with the Cu substrate. The melting behavior, microstructure, tensile strength, and wettability of the SCNG-x（x=Ag, Bi, In, Sb） solders were examined. The findings revealed that the introduction of Ag, Bi, In, and Sb minimally altered the solidus temperature, liquidus temperature, and tensile strength of the solder. However, the cooling behavior and solidified microstructure of the solder were affected by the concentration of the alloying elements. The wettability of the SCNG solder was improved with the doping of the alloying elements except Sb. The thickness of intermetallic layer was increased by the addition of the alloying elements and was related to the cooling behavior of the solder. The morphology of intermetallic layer between the SCNG-x solders and the Cu substrate was different from that of the typical SAC solders. In conclusion, alloying the SCNG solder with Ag, Bi, In or Sb is able to improve particular properties of the solder.

Interfacial microstructure evolution and mechanical properties of Al/Sn joints by ultrasonic-assisted soldering

Soldering aluminum alloys at low temperature have great potential to avoid softening of base metals.Pure Al was solderedwith pure tin assisted by ultrasound.The influence of primaryα(Al)on the microstructure of Al/Sn interface and its bonding strengthwas studied.It is found that the primaryα(Al)in liquid tin tends to be octahedron enclosed by Al{111}facet with the lowest surfacefree energy and growth rate.The ultrasonic action could increase the nucleation rate and refine the particles of primaryα(Al).For thelonger ultrasonic and holding time,a large amount of the octahedral primaryα(Al)particles crystallize at the Al/Sn interface.Thebonding interface exhibits the profile of rough dentation,resulting in an increment of bonding interface area and the effect ofmechanical occlusion.The bonding strength at interface could reach63MPa with ultrasonic time of40s and holding time of10min.