Well-dispersed SnO2 nanorods with diameter of 4-15 nm and length of 100-200 nm are synthesised through a hydrothermal route and their potential as anode materials in lithium-ion batteries is investigated. The observed...Well-dispersed SnO2 nanorods with diameter of 4-15 nm and length of 100-200 nm are synthesised through a hydrothermal route and their potential as anode materials in lithium-ion batteries is investigated. The observed initial discharge capacity is as high as 1778 mA.h/g, much higher than the theoretical value of the bulk SnO2 （1494 mA.h/g）. During the following 15 cycles, the reversible capacity decreases from 929 to 576 mA-h/g with a fading rate of 3.5% per cycle. The fading mechanism is discussed. Serious capacity fading can be avoided by reducing the cycling voltages from 0.05-3.0 to 0.4-1.2 V. At the end, SnO2 nanorods with much smaller size are synthesized and their performance as anode materials is studied. The size effect on the electrochemical properties is briefly discussed.展开更多
Flower-liked SnO_2 nanorods were prepared by a hydrothermal method.The sensors were fabricated using SnO_2 nanorods adsorption of Au nanoparticles through sputtering deposition.We found that the loading of a small amo...Flower-liked SnO_2 nanorods were prepared by a hydrothermal method.The sensors were fabricated using SnO_2 nanorods adsorption of Au nanoparticles through sputtering deposition.We found that the loading of a small amount of Au nanoparticles on the surface of SnO_2 nanorods can effectively enhance and functionalize the gas sensing performance of SnO_2 nanorods,which due to the Au adsorption make the surface-depletion effect more pronounced.Such enhanced surface depletion increases the sensitivity,lowers the operation temperature and decreases the response time.展开更多
1 Results Micro-porous polymer electrolytes(MPEs), which almost obtained by the conventional methods of phase inversion process or immersion precipitation method, have significant advantages such as high ionic conduct...1 Results Micro-porous polymer electrolytes(MPEs), which almost obtained by the conventional methods of phase inversion process or immersion precipitation method, have significant advantages such as high ionic conductivity and excellent mechanical properties[1].In our work, micro-porous structure is obtained by adding SnO2 nanorods usually used as gas senor materials into the polymer matrix, which proves a new way to prepare MPEs.SnO2 nanorods were synthesized by microemulsion hydrothermal method[2]. Th...展开更多
Efficiently and thoroughly degrading organic dyes in wastewater is of great importance and challenge.Herein,vertically oriented mesoporous a-Fe_(2)O_(3)nanorods array(a-Fe_(2)O_(3)-NA)is directly grown on fluorine-dop...Efficiently and thoroughly degrading organic dyes in wastewater is of great importance and challenge.Herein,vertically oriented mesoporous a-Fe_(2)O_(3)nanorods array(a-Fe_(2)O_(3)-NA)is directly grown on fluorine-doped tin oxide(FTO)glass and employed as the photoanode for photoelectrocatalytic degradation of methylene blue simulated dye wastewater.The Ovsites on the a-Fe_(2)O_(3)-NA surface are the active sites for methylene blue(MB)adsorption.Electrons transfer from the adsorbed MB to Fe-O is detected.Compared with electrocatalytic and photocatalytic degradation processes,the photoelectrocatalytic(PEC)process exhibited the best degrading performance and the largest kinetic constant.Hydroxyl,superoxide free radicals,and photo-generated holes play a jointly leading role in the PEC degradation.A possible degrading pathway is suggested by liquid chromatography-mass spectroscopy analysis.This work demonstrates that photoelectrocatalysis by a-Fe_(2)O_(3)-NA has a remarkable superiority over photocatalysis and electrocatalysis in MB degradation.The in-depth investigation of photoelectrocatalytic degradation mechanism in this study is meaningful for organic wastewater treatment.展开更多
Nanostructured materials have drawn considerable attention because they are promising candidates for nextgeneration electronic and photonic devices with low power consumption[1-5]. A number of methods, such as las... Nanostructured materials have drawn considerable attention because they are promising candidates for nextgeneration electronic and photonic devices with low power consumption[1-5]. A number of methods, such as laser ablation[6], template-induced growth[7], arc discharge [8], vapor transport [9], and molecular-beam epitaxy[10] have been developed to synthesize Si, Ge, MgO,SnO2, GaN, and Ga2O3 nanowires or nanorods[11-15].……展开更多
As typical quarternary copper-based chalcogenides,Cu–Zn–Sn–S nanocrystals(CZTS NCs)have emerged as a newfashioned electrocatalyst in hydrogen evolution reactions(HERs).Oleylamine(OM),a reducing surfactant and solve...As typical quarternary copper-based chalcogenides,Cu–Zn–Sn–S nanocrystals(CZTS NCs)have emerged as a newfashioned electrocatalyst in hydrogen evolution reactions(HERs).Oleylamine(OM),a reducing surfactant and solvent,plays a significant role in the assisting synthesis of CZTS NCs due to the ligand effect.Herein,we adopted a facile one-pot colloidal method for achieving the structure evolution of CZTS NCs from 2D nanosheets to 1D nanorods assisted through the continuous addition of OM.During the process,the mechanism of OM-induced morphology evolution was further discussed.When merely adding pure 1-dodecanethiol(DDT)as the solvent,the CZTS nanosheets were obtained.As OM was gradually added to the reaction,the CZTS NCs began to grow along the sides of the nanosheets and gradually shrink at the top,followed by the formation of stable nanorods.In acidic electrolytic conditions,the CZTS NCs with 1.0 OM addition display the optimal HER activity with a low overpotential of 561 m V at 10 m A/cm^(2) and a small Tafel slope of 157.6 m V/dec compared with other CZTS samples.The enhancement of HER activity could be attributed to the contribution of the synergistic effect of the diverse crystal facets to the reaction.展开更多
Here,CuO nanorods fabricated via pulsed laser ablation in liquids were decorated with Ir,Pd,and Ru NPs(loading~7 wt%) through pulsed laser irradiation in the liquids process.The resulting NPs-decorated CuO nanorods we...Here,CuO nanorods fabricated via pulsed laser ablation in liquids were decorated with Ir,Pd,and Ru NPs(loading~7 wt%) through pulsed laser irradiation in the liquids process.The resulting NPs-decorated CuO nanorods were characterized spectroscopically and employed as multifunctional electrocatalysts in OER,HER,and the furfural oxidation reactions(FOR).Ir-CuO nanorods afford the lowest overpotential of~345 mV(HER) and 414 mV(OER) at 10 mA cm^(-2),provide the highest 2-furoic acid yield(~10.85 mM) with 64.9% selectivity,and the best Faradaic efficiency~72.7% in 2 h of FOR at 1.58 V(vs.RHE).In situ electrochemical-Raman analysis of the Ir-CuO detects the formation of the crucial intermediates,such as Cu(Ⅲ)-oxide,Cu(OH)_(2),and Ir_x(OH)_y,on the electrode-electrolyte surface,which act as a promoter for HER and OER.The Ir-CuO ‖ Ir-CuO in a coupled HER and FOR-electrolyzer operates at~200 mV lower voltage,compared with the conventional electrolyzer and embodies the dual advantage of energy-saving H_(2) and 2-furoic acid production.展开更多
In this experiment, Cu<sup>2+</sup> doped ZnO (Cu-ZnO) nanorods materials have been fabricated by hydrothermal method. Cu<sup>2+</sup> ions were doped into ZnO with ratios of 2, 5 and 7 mol.% (...In this experiment, Cu<sup>2+</sup> doped ZnO (Cu-ZnO) nanorods materials have been fabricated by hydrothermal method. Cu<sup>2+</sup> ions were doped into ZnO with ratios of 2, 5 and 7 mol.% (compared to the mole’s number of Zn<sup>2+</sup>). The hexamethylenetetramine (HMTA) solvent used for the fabrication of Cu-ZnO nanorods with the mole ratio of Zn<sup>2+</sup>:HMTA = 1:4. The characteristics of the materials were analyzed by techniques, such as XRD, Raman shift, SEM and UV-vis diffuse reflectance spectra (DRS). The photocatalytic properties of the materials were investigated by the decomposition of the methylene blue (MB) dye solution under ultraviolet light. The results show that the size of Cu-ZnO nanorods was reduced when the Cu<sup>2+</sup> doping ratio increased from 2 mol.% to 7 mol.%. The decomposition efficiency of the MB dye solution reached 92% - 97%, corresponding to the Cu<sup>2+</sup> doping ratio changed from 2 - 7 mol.% (after 40 minutes of ultraviolet irradiation). The highest efficiency for the decomposition of the MB solution was obtained at a Cu<sup>2+</sup> doping ratio of 2 mol.%.展开更多
基金Project supported by the National Key Basic Research Program of China (Grant No 2007CB310500)the Chinese Ministry of Education (Grant No 705040)the National Natural Science Foundation of China (Grant Nos 90606009, 60571044 and 10774174)
文摘Well-dispersed SnO2 nanorods with diameter of 4-15 nm and length of 100-200 nm are synthesised through a hydrothermal route and their potential as anode materials in lithium-ion batteries is investigated. The observed initial discharge capacity is as high as 1778 mA.h/g, much higher than the theoretical value of the bulk SnO2 （1494 mA.h/g）. During the following 15 cycles, the reversible capacity decreases from 929 to 576 mA-h/g with a fading rate of 3.5% per cycle. The fading mechanism is discussed. Serious capacity fading can be avoided by reducing the cycling voltages from 0.05-3.0 to 0.4-1.2 V. At the end, SnO2 nanorods with much smaller size are synthesized and their performance as anode materials is studied. The size effect on the electrochemical properties is briefly discussed.
文摘Flower-liked SnO_2 nanorods were prepared by a hydrothermal method.The sensors were fabricated using SnO_2 nanorods adsorption of Au nanoparticles through sputtering deposition.We found that the loading of a small amount of Au nanoparticles on the surface of SnO_2 nanorods can effectively enhance and functionalize the gas sensing performance of SnO_2 nanorods,which due to the Au adsorption make the surface-depletion effect more pronounced.Such enhanced surface depletion increases the sensitivity,lowers the operation temperature and decreases the response time.
文摘1 Results Micro-porous polymer electrolytes(MPEs), which almost obtained by the conventional methods of phase inversion process or immersion precipitation method, have significant advantages such as high ionic conductivity and excellent mechanical properties[1].In our work, micro-porous structure is obtained by adding SnO2 nanorods usually used as gas senor materials into the polymer matrix, which proves a new way to prepare MPEs.SnO2 nanorods were synthesized by microemulsion hydrothermal method[2]. Th...
基金financially supported by the National Natural Science Foundation of China (22005097)the State Key Laboratory of Physical Chemistry of Solid Surfaces,Xiamen University,Xiamen 361005,P.R.China (201815)。
文摘Efficiently and thoroughly degrading organic dyes in wastewater is of great importance and challenge.Herein,vertically oriented mesoporous a-Fe_(2)O_(3)nanorods array(a-Fe_(2)O_(3)-NA)is directly grown on fluorine-doped tin oxide(FTO)glass and employed as the photoanode for photoelectrocatalytic degradation of methylene blue simulated dye wastewater.The Ovsites on the a-Fe_(2)O_(3)-NA surface are the active sites for methylene blue(MB)adsorption.Electrons transfer from the adsorbed MB to Fe-O is detected.Compared with electrocatalytic and photocatalytic degradation processes,the photoelectrocatalytic(PEC)process exhibited the best degrading performance and the largest kinetic constant.Hydroxyl,superoxide free radicals,and photo-generated holes play a jointly leading role in the PEC degradation.A possible degrading pathway is suggested by liquid chromatography-mass spectroscopy analysis.This work demonstrates that photoelectrocatalysis by a-Fe_(2)O_(3)-NA has a remarkable superiority over photocatalysis and electrocatalysis in MB degradation.The in-depth investigation of photoelectrocatalytic degradation mechanism in this study is meaningful for organic wastewater treatment.
文摘 Nanostructured materials have drawn considerable attention because they are promising candidates for nextgeneration electronic and photonic devices with low power consumption[1-5]. A number of methods, such as laser ablation[6], template-induced growth[7], arc discharge [8], vapor transport [9], and molecular-beam epitaxy[10] have been developed to synthesize Si, Ge, MgO,SnO2, GaN, and Ga2O3 nanowires or nanorods[11-15].……
基金partially supported by National Natural Science Foundation of China (12274021 and 62075005)。
文摘As typical quarternary copper-based chalcogenides,Cu–Zn–Sn–S nanocrystals(CZTS NCs)have emerged as a newfashioned electrocatalyst in hydrogen evolution reactions(HERs).Oleylamine(OM),a reducing surfactant and solvent,plays a significant role in the assisting synthesis of CZTS NCs due to the ligand effect.Herein,we adopted a facile one-pot colloidal method for achieving the structure evolution of CZTS NCs from 2D nanosheets to 1D nanorods assisted through the continuous addition of OM.During the process,the mechanism of OM-induced morphology evolution was further discussed.When merely adding pure 1-dodecanethiol(DDT)as the solvent,the CZTS nanosheets were obtained.As OM was gradually added to the reaction,the CZTS NCs began to grow along the sides of the nanosheets and gradually shrink at the top,followed by the formation of stable nanorods.In acidic electrolytic conditions,the CZTS NCs with 1.0 OM addition display the optimal HER activity with a low overpotential of 561 m V at 10 m A/cm^(2) and a small Tafel slope of 157.6 m V/dec compared with other CZTS samples.The enhancement of HER activity could be attributed to the contribution of the synergistic effect of the diverse crystal facets to the reaction.
基金supported by the Korea Basic Science Institute (National research Facilities and Equipment Center) grant funded by the Ministry of Education. (2019R1A6C1010042, 2021R1A6C103A427)the financial support from the National Research Foundation of Korea (NRF), (2022R1A2C2010686, 2022R1A4A3033528, 2021R1I1A1A01060380, 2019H1D3A1A01071209)。
文摘Here,CuO nanorods fabricated via pulsed laser ablation in liquids were decorated with Ir,Pd,and Ru NPs(loading~7 wt%) through pulsed laser irradiation in the liquids process.The resulting NPs-decorated CuO nanorods were characterized spectroscopically and employed as multifunctional electrocatalysts in OER,HER,and the furfural oxidation reactions(FOR).Ir-CuO nanorods afford the lowest overpotential of~345 mV(HER) and 414 mV(OER) at 10 mA cm^(-2),provide the highest 2-furoic acid yield(~10.85 mM) with 64.9% selectivity,and the best Faradaic efficiency~72.7% in 2 h of FOR at 1.58 V(vs.RHE).In situ electrochemical-Raman analysis of the Ir-CuO detects the formation of the crucial intermediates,such as Cu(Ⅲ)-oxide,Cu(OH)_(2),and Ir_x(OH)_y,on the electrode-electrolyte surface,which act as a promoter for HER and OER.The Ir-CuO ‖ Ir-CuO in a coupled HER and FOR-electrolyzer operates at~200 mV lower voltage,compared with the conventional electrolyzer and embodies the dual advantage of energy-saving H_(2) and 2-furoic acid production.
文摘In this experiment, Cu<sup>2+</sup> doped ZnO (Cu-ZnO) nanorods materials have been fabricated by hydrothermal method. Cu<sup>2+</sup> ions were doped into ZnO with ratios of 2, 5 and 7 mol.% (compared to the mole’s number of Zn<sup>2+</sup>). The hexamethylenetetramine (HMTA) solvent used for the fabrication of Cu-ZnO nanorods with the mole ratio of Zn<sup>2+</sup>:HMTA = 1:4. The characteristics of the materials were analyzed by techniques, such as XRD, Raman shift, SEM and UV-vis diffuse reflectance spectra (DRS). The photocatalytic properties of the materials were investigated by the decomposition of the methylene blue (MB) dye solution under ultraviolet light. The results show that the size of Cu-ZnO nanorods was reduced when the Cu<sup>2+</sup> doping ratio increased from 2 mol.% to 7 mol.%. The decomposition efficiency of the MB dye solution reached 92% - 97%, corresponding to the Cu<sup>2+</sup> doping ratio changed from 2 - 7 mol.% (after 40 minutes of ultraviolet irradiation). The highest efficiency for the decomposition of the MB solution was obtained at a Cu<sup>2+</sup> doping ratio of 2 mol.%.
