SnO2 nanocrystal and rare-earth Eu^3＋ ion co-doped SiO2 thin films are prepared by sol-gel and spin coating methods. The formation of tetragonal rutile structure SnO2 nanocrystals with a uniform distribution is confi...SnO2 nanocrystal and rare-earth Eu^3＋ ion co-doped SiO2 thin films are prepared by sol-gel and spin coating methods. The formation of tetragonal rutile structure SnO2 nanocrystals with a uniform distribution is confirmed by X-ray diffraction and transmission electron microscopy. Fourier transform infrared spectroscopy is used to investigate the densities of the hydroxyl groups, and it is found that the emission intensity from the 5Do-TF2 transitions of the Eu^3＋ ions is enhanced by two orders of magnitude due to energy transfer from the oxygen-vacancy-related defects of the SnO2 nanocrystals to nearby Eu^3＋ ions. The influences of the amounts of Sn and the post-annealing temperatures are systematically evaluated to further understand the mechanism of energy transfer. The luminescence intensity ratio of Eu^3＋ ions from electric dipole transition and magnetic dipole transition indicate the different probable locations of Eu^3＋ ions in the sol-gel thin film, which are further discussed based on temperature-dependent photoluminescence measurements.展开更多
This paper reports that a series of NiCuZn ferrite powders and films are prepared by using sol-gel method. The effects of raw material composition and the calcinate temperature on magnetic properties of them are inves...This paper reports that a series of NiCuZn ferrite powders and films are prepared by using sol-gel method. The effects of raw material composition and the calcinate temperature on magnetic properties of them are investigated. The NiCuZn ferrite powders are prepared by the self-propagating high-temperature synthesis method and subsequently heated at 700 ℃-1000 ℃. The results show that NiCuZn ferrite powders with single spinel phase can be formed after heat-treating at 750 ℃. Powders obtained from Ni0.4Cu0.2Zn0.4Fel.904 gel have better magnetic properties than those from gels with other composition. After heat-treating at 900 ℃for 3 h, coercivity Hc and saturation magnetization Ms are 9.70e （i Oe = 80 A/m） and 72.4 emu/g, respectively. Different from the powders, NiCuZn films produced on Si （100） from the Ni0.4Cuo.2Zno.4Fe204 gel formed at room temperature possess high properties. When heat-treating condition is around 600 ℃for 6 rain, samples with low Hc and high Ms will be obtained. The minimal Hc is 16.70e and Ms is about 300 emu/cm3. In comparison with the films prepared through long-time heat treating, the films prepared through short heat-treating time exhibits better soft magnetic properties.展开更多
A series of silica-phosphate nano-composites prepared as a host thin films Physical Properties of Nano-Composite Silica-Phosphate Thin Film Prepared by Sol Gel Technique and doped with different concentrations of Er3+...A series of silica-phosphate nano-composites prepared as a host thin films Physical Properties of Nano-Composite Silica-Phosphate Thin Film Prepared by Sol Gel Technique and doped with different concentrations of Er3+ ions have been synthesized using tetraesoxysilane TEOS, triethylphosphate TEP and erbium nitrate as precursor sources of silica, phosphorus and erbium oxides. The structural properties of pure silica-phosphate thin films and doped with different concentrations of Er3+ ions were studied, using x-ray diffraction (XRD) and Fourier Transform Infrared (FTIR). The morphology of silica-phosphate was characterized by Scanning electron microscope (SEM).展开更多
The structural, dielectric and magnetic properties of pure and Fe-Co co-doped Ba0.9Sr0.1TiO3, (Ba(1-x)SrxTiO3, where (x = 0.10) and (Ba0.9Sr0.1Ti(1-x-y)FexCoyO3), where (x = 0.1, y = 0) and (x = 0 and y = 0.10) and (x...The structural, dielectric and magnetic properties of pure and Fe-Co co-doped Ba0.9Sr0.1TiO3, (Ba(1-x)SrxTiO3, where (x = 0.10) and (Ba0.9Sr0.1Ti(1-x-y)FexCoyO3), where (x = 0.1, y = 0) and (x = 0 and y = 0.10) and (x = 0.5, y = 0.5) in powder form, abbreviated as (BST) and (BST10FO), (BST10CO) and (BST5F5CO), respectively were prepared by a modified sol gel technique. Crystallization, surface morphology and electrical behavior of BST are improved by Fe3+ and Co2+ ions with optimized grain size. Phase identification by using X-ray diffraction and surface morphology will be studied by using transmission electron microscope (TEM) and scanning electron microscope imaging (SEM). Phase identification by using X-ray diffraction and surface morphology evaluation by using transmission electron microscope (TEM) and scanning electron microscope imaging (SEM) will be studied. The nano-scale presence and the formation of the tetragonal perovskite phase as well as the crystallinity were detected using the mentioned techniques. The dielectric properties of the prepared samples have been investigated as a function of temperature and frequency. The dielectric measurements are carried out in the frequency range of 42 Hz - 1 MHz, at temperature ranging between 25°C and 250°C. The results showed an abrupt decrease in the dielectric permittivity by increasing the frequency range. The magnetic hysteresis loop confirmed enhancement in the magnetization properties by co-doping with Fe3+-Co2+ ions. An increase in the saturation of the magnetization at room temperature was detected by decreasing the crystallite sizes of the prepared samples.展开更多
In this work, Undoped Zinc Oxide (ZnO) and Sndoped Zinc Oxide (ZnO:Sn) films have been deposited by sol-gel dip coating method, where the Sn/Zn atomic ratio was 3% and 5% in the solution. The effects of Sn incorporati...In this work, Undoped Zinc Oxide (ZnO) and Sndoped Zinc Oxide (ZnO:Sn) films have been deposited by sol-gel dip coating method, where the Sn/Zn atomic ratio was 3% and 5% in the solution. The effects of Sn incorporation on morphological, structural and optical properties of ZnO films were investigated. The Scanning Electron Microscopy (SEM) showed that the morphological surface of the films was affected by Sn low doping. The X-Ray Diffraction (XRD) patterns showed that all films have polycrystalline structures, and the doping incorporation has not lead to substantial changes in the structural characteristics of ZnO films. The crystallite size was calculated using the well-known Scherrer’s formula and found to be in the range of 23 - 40 nm. The measurements from UV-Visible Spectrophotometer (U-Vis) indicated that the highest average optical transmittance in the visible region was related to Undoped ZnO film, then the optical band gap and Urbach energy values of thin films were calculated. The X-Ray Photoelectron Spectroscopy (XPS) has demonstrated that Sn is incorporated in ZnO lattice.展开更多
This paper concentrates on the development of glasses with self-cleaning surfaces exhibiting high water contact angles. In this study, we prepared super-hydrophobic nano-ceramic coated glass based on titania & sil...This paper concentrates on the development of glasses with self-cleaning surfaces exhibiting high water contact angles. In this study, we prepared super-hydrophobic nano-ceramic coated glass based on titania & silica using simple sol-gel & dip coating methods and studied the best composition of the coatings by altering ratios of titanium tetraisopropoxide (TTIP)/tetraethyl orthosilicate (TEOS) with different homogenizing agents. We characterized the coatings by surface roughness measurement, percentage of optical transmission, static contact angle, near-infrared (NIR) transmission, and diffuse reflectance. The fabrication of coatings on glass substrates played an important role in increasing the water contact angle of about 95° and visible & NIR transmission of about 90%. We compared our modified glass substrate with commercial low emissivity (Low E) glass using X-ray diffraction (XRD) analysis, which showed pure amorphous surface claiming excellent wettability and thus the prepared glass substrate could have a variety of applications in different fields.展开更多
基金Project supported by the National Natural Science Foundation of China(Grant No.61036001)the Natural Science Foundation of Jiangsu Province,China(Grant No.BK2010010)the Fundamental Research Funds for the Central Universities of China(Grant Nos.1112021001 and 1116021003)
文摘SnO2 nanocrystal and rare-earth Eu^3＋ ion co-doped SiO2 thin films are prepared by sol-gel and spin coating methods. The formation of tetragonal rutile structure SnO2 nanocrystals with a uniform distribution is confirmed by X-ray diffraction and transmission electron microscopy. Fourier transform infrared spectroscopy is used to investigate the densities of the hydroxyl groups, and it is found that the emission intensity from the 5Do-TF2 transitions of the Eu^3＋ ions is enhanced by two orders of magnitude due to energy transfer from the oxygen-vacancy-related defects of the SnO2 nanocrystals to nearby Eu^3＋ ions. The influences of the amounts of Sn and the post-annealing temperatures are systematically evaluated to further understand the mechanism of energy transfer. The luminescence intensity ratio of Eu^3＋ ions from electric dipole transition and magnetic dipole transition indicate the different probable locations of Eu^3＋ ions in the sol-gel thin film, which are further discussed based on temperature-dependent photoluminescence measurements.
基金supported by the National Natural Science Foundation of China (Grant No. 61003041)the Fundamental Research Funds for the Central Universities (Grant No. lzujbky-2010-81)
文摘This paper reports that a series of NiCuZn ferrite powders and films are prepared by using sol-gel method. The effects of raw material composition and the calcinate temperature on magnetic properties of them are investigated. The NiCuZn ferrite powders are prepared by the self-propagating high-temperature synthesis method and subsequently heated at 700 ℃-1000 ℃. The results show that NiCuZn ferrite powders with single spinel phase can be formed after heat-treating at 750 ℃. Powders obtained from Ni0.4Cu0.2Zn0.4Fel.904 gel have better magnetic properties than those from gels with other composition. After heat-treating at 900 ℃for 3 h, coercivity Hc and saturation magnetization Ms are 9.70e （i Oe = 80 A/m） and 72.4 emu/g, respectively. Different from the powders, NiCuZn films produced on Si （100） from the Ni0.4Cuo.2Zno.4Fe204 gel formed at room temperature possess high properties. When heat-treating condition is around 600 ℃for 6 rain, samples with low Hc and high Ms will be obtained. The minimal Hc is 16.70e and Ms is about 300 emu/cm3. In comparison with the films prepared through long-time heat treating, the films prepared through short heat-treating time exhibits better soft magnetic properties.
文摘A series of silica-phosphate nano-composites prepared as a host thin films Physical Properties of Nano-Composite Silica-Phosphate Thin Film Prepared by Sol Gel Technique and doped with different concentrations of Er3+ ions have been synthesized using tetraesoxysilane TEOS, triethylphosphate TEP and erbium nitrate as precursor sources of silica, phosphorus and erbium oxides. The structural properties of pure silica-phosphate thin films and doped with different concentrations of Er3+ ions were studied, using x-ray diffraction (XRD) and Fourier Transform Infrared (FTIR). The morphology of silica-phosphate was characterized by Scanning electron microscope (SEM).
文摘The structural, dielectric and magnetic properties of pure and Fe-Co co-doped Ba0.9Sr0.1TiO3, (Ba(1-x)SrxTiO3, where (x = 0.10) and (Ba0.9Sr0.1Ti(1-x-y)FexCoyO3), where (x = 0.1, y = 0) and (x = 0 and y = 0.10) and (x = 0.5, y = 0.5) in powder form, abbreviated as (BST) and (BST10FO), (BST10CO) and (BST5F5CO), respectively were prepared by a modified sol gel technique. Crystallization, surface morphology and electrical behavior of BST are improved by Fe3+ and Co2+ ions with optimized grain size. Phase identification by using X-ray diffraction and surface morphology will be studied by using transmission electron microscope (TEM) and scanning electron microscope imaging (SEM). Phase identification by using X-ray diffraction and surface morphology evaluation by using transmission electron microscope (TEM) and scanning electron microscope imaging (SEM) will be studied. The nano-scale presence and the formation of the tetragonal perovskite phase as well as the crystallinity were detected using the mentioned techniques. The dielectric properties of the prepared samples have been investigated as a function of temperature and frequency. The dielectric measurements are carried out in the frequency range of 42 Hz - 1 MHz, at temperature ranging between 25°C and 250°C. The results showed an abrupt decrease in the dielectric permittivity by increasing the frequency range. The magnetic hysteresis loop confirmed enhancement in the magnetization properties by co-doping with Fe3+-Co2+ ions. An increase in the saturation of the magnetization at room temperature was detected by decreasing the crystallite sizes of the prepared samples.
文摘In this work, Undoped Zinc Oxide (ZnO) and Sndoped Zinc Oxide (ZnO:Sn) films have been deposited by sol-gel dip coating method, where the Sn/Zn atomic ratio was 3% and 5% in the solution. The effects of Sn incorporation on morphological, structural and optical properties of ZnO films were investigated. The Scanning Electron Microscopy (SEM) showed that the morphological surface of the films was affected by Sn low doping. The X-Ray Diffraction (XRD) patterns showed that all films have polycrystalline structures, and the doping incorporation has not lead to substantial changes in the structural characteristics of ZnO films. The crystallite size was calculated using the well-known Scherrer’s formula and found to be in the range of 23 - 40 nm. The measurements from UV-Visible Spectrophotometer (U-Vis) indicated that the highest average optical transmittance in the visible region was related to Undoped ZnO film, then the optical band gap and Urbach energy values of thin films were calculated. The X-Ray Photoelectron Spectroscopy (XPS) has demonstrated that Sn is incorporated in ZnO lattice.
文摘This paper concentrates on the development of glasses with self-cleaning surfaces exhibiting high water contact angles. In this study, we prepared super-hydrophobic nano-ceramic coated glass based on titania & silica using simple sol-gel & dip coating methods and studied the best composition of the coatings by altering ratios of titanium tetraisopropoxide (TTIP)/tetraethyl orthosilicate (TEOS) with different homogenizing agents. We characterized the coatings by surface roughness measurement, percentage of optical transmission, static contact angle, near-infrared (NIR) transmission, and diffuse reflectance. The fabrication of coatings on glass substrates played an important role in increasing the water contact angle of about 95° and visible & NIR transmission of about 90%. We compared our modified glass substrate with commercial low emissivity (Low E) glass using X-ray diffraction (XRD) analysis, which showed pure amorphous surface claiming excellent wettability and thus the prepared glass substrate could have a variety of applications in different fields.
