Structural evolution-enabled BiFeO3 modulated by strontium doping with enhanced dielectric,optical and superparamagnetic properties by a modified sol-gel method

Multiferroic(BFO)nanoparticles doped with strontium with the general formula Bi1-xSrx FeO3(x=0,0.3,0.5,0.7)were synthesized using a modified sol-gel auto-combustion process.The structural,electrical,optical,and magnetic properties of the samples are discussed.The structural analysis,carried out using the x-ray powder diffraction technique,shows a structural transition from rhombohedral(R-3c)to cubic(Pm-3m)for the doping amount of strontium(Sr)equal to x=0.3.Morphological analysis of the prepared samples were carried out using scanning electron microscopy(SEM).Frequency-dependent dielectric constant and ac conductivity were studied.The doped samples,with improved dielectric properties,can be used to fabricate different optoelectronic devices.Strong dielectric dispersion and broad relaxation were exhibited by all the samples.Cole–Cole plots were employed as an effective tool to study the dispersion parameters,namely,the optical dielectric constant,static dielectric constant,relaxation time,and spreading factor.The activation energy was calculated from the relaxation peaks and Cole–Cole plots,which were found to be compatible with each other.The bandgap of the samples was calculated using diffuse reflectance spectral(DRS)analysis.Sharp and strong photoluminescence in the IR region was observed in the samples,similar to ZnO,which was reported for the first time.Room-temperature and low-temperature magnetization studies point towards the superparamagnetic nature of the samples,with an improvement in magnetic properties with doping.The antiferromagnetic behavior of bulk bismuth ferrite transforms to superparamagnetic in nature for both pure and Sr-substituted bismuth ferrite nanoparticles due to the close dimensions of crystallite size with magnetic domains leading to the break-down of the frustrated spin cycloidal moment.

Photocatalytic Activity of Nanosized ZnWO_4 Prepared by the Sol-gel Method

Nanosized ZnWO4 photocatalysts were successfully synthesized via the sol-gel process in a temperature range of 450-800℃. The grain size, crystal size, and crystallinity of ZnWO4 particles increased with the increase of calcina- tion temperature and prolonging calcination time. The photocatalytic activity was measured for the degradation of an aqueous Rhodamine-B（RhB） solution and gaseous formaldehyde（FAD）. With the increase of calcination temperature and time, the activities increased to a maximum and then decreased. ZnWO4 photocatalyst prepared at 550℃ for I0 h showed the highest activity, which is similar to the photocatalytic activity of P25TiO2 for the degradation of gase-ous FAD. High crystallinity, large surface area, and good dispersion are responsible for the high photocatalytic per- formance of the prepared ZnWO4.

Grain Size and Photocatalytic Activity of Nanometer TiO_2 Thin Films Prepared by the Sol-gel Method

Transparent anatase TiO2 nanometer thin films with photocatalytic activity were prepared via the sol-gel method on soda-lime glass. The thickness , crystalline phase, grain size, surface hydroxyl amount and so on were characterized by scanning electron microscopy (SEM) , X-ray diffraction (XRD), transmission electron microscopy ( TEM), X-ray photoelectron spectroscopy (XPS) and UV-visible spectrophotometer ( UV-VIS). The photocatalytic activity of TiO2 thin films was evaluated for the photocatalytic decolorization of aqueous methyl orange . The effects of film thickness on the crystalline phase, grain size, transmittance and photocatalytic activity of nanometer Ti02 thin films were discussed.

Surface and Texture Properties of Tb-Doped Ceria-Zirconia Solid Solution Prepared by Sol-Gel Method

The three-way catalysts （TWCs） promoters Ce0.6Zr0.4- x TbxO2-y were prepared by sol-gel method. BET surface areas analysis indicated that an increase of the dopant Tb content from x = 0.05 to x = 0.15 favors an increase of surface area from 66.8 to 80.4 m^2· g^-1 compared with the undoped sample Ce0 .6oZr0.40O2 65.1 m^2·g^- 1 after calcination at 650℃. Transmission electron microscopy （TEM） observation indicated that the doped samples have a higher thermal stability. The XRD and Raman spectra confirmed that the Ce0.6Zr0.4-xTbxO2-y cubic solid solution is formed. XPS analysis revealed that Ce and Tb mainly existed in the form of Ce^4＋ and Tb^3 ＋ , and Zr existed in the form of Zr^4＋ on the surface of the samples. The doped samples were homogenous in composition ; the introduction of Tb into the CeO2-ZrO2 promoters resuited in the formation of a solid solution, and the concentration of surface lattice oxygen was increased.

Synthesis of Long Afterglow Photoluminescent Materials Sr_2MgSi_2O_7∶Eu^(2+), Dy^(3+) by Sol-Gel Method

Long afterglow photoluminescent materials Sr2MgSi2O7 doped with Eu2+, Dy3+ were prepared by sol-gel method. The synthesized samples were characterized by X-ray diffraction. The excitation spectrum, emission spectrum and long decay curve were measured and analyzed. XRD pattern indicates that phosphor is with Sr2MgSi2O7 crystal structure. The wide range of excitation wavelength indicates that luminescent material can be excited by light from ultraviolet ray to visible light. The main peak of emission spectrum is located at 466 nm. Sample excited by visible light can emit bright blue light, and the afterglow time lasts more than 8 h.

Luminescence properties of red-emitting Ca_2Al_2SiO_7:Eu^(3+) nanoparticles prepared by sol-gel method

A series of red-emitting Ca2_xA12SiOT：xEu^3＋ （x = 1 mol.%-10 tool.%） phosphors were synthesized by the sol-gel method. The effects of annealing temperature and doping concentration on the crystal structure and luminescence properties of Ca2A12SiO7：Eu^3＋ phosphors were investigated. X-ray diffraction （XRD） profiles showed that all peaks could be attributed to the tetragonal Ca2A12SiO7 phase when the sample was annealed at 1000℃. Scanning electron microscopy （SEM） micrographs indicate that the phosphors have an irregularly rounded mor- phology with particles of about 200 nm. Excitation spectra showed that the strong broad band at around 258 nm and weak sharp lines in 350-490 nm were attributed to the charge transfer band of Eu^3＋-O^2- and f-f transitions within the 4f^6 configuration of Eu^3＋ ions, respectively. Emission spectra implied that the red luminescence could be attributed to the transitions from the ^5D0 excited level to the 7Fj （J = 0, 1, 2, 3, 4） levels of Eu3＋ions with the main electric dipole transition ^5D0→^7F2 （618 and 620 nm）, and Eu^3＋ ions prefer to occupy a lower symmetry site in the crystal lattice. Moreover, the photoluminescence （PL） intensity was strongly dependent on both the sintering temperature and doping concentration, and the highest PL intensity was observed at an Eu^3＋ concentration x = 7 mol.% after annealing at ll00℃. The obtained Ca2A12SiO7：Eu^＋3＋ phosphor may have potential application for the red lamp phosphor.

Synthesis and Characterization of Nanocrystalline SrAl_2O_4∶Eu, Dy Long Afterglow Phosphors by Sol-Gel Method

Eu 2+, Dy 3+ co-doped nanocrystalline strontium aluminate phosphor powders with brightness and long afterglow were synthesized by the sol-gel method at 1200 ℃ for 2 h. The samples were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results of XRD show that the single crystalline phase is α-SrAl_2O_4. According to the observation of SEM, the particles of the samples are needle-like. Compared with the samples synthesized by solid state reaction, the grain size of the sol-gel method is to nanometer grade. A clear blue shift occurs in the excitation and emission spectra. The blue shift in nanocrystalline SrAl_2O_4∶Eu, Dy phosphor can be attributed to the quantum-size-effect of the luminescent particles.

Preparation of Perovskite-Type Oxides La_(1-x)Sr_xFe_(1-y)Co_yO_3 Using EDTA Sol-Gel Method

Two series of perovskite-type oxides with composition (La_(1-x))Sr_xFeO_3(x≤0.8)and La_(1-x)Sr_xFe_(1-y)Co_yO_3(x=0.2; y=0.2, 0.4)powder productions were synthesized by EDTA complexing sol-gel method. The products were characterized by XRD, TEM, SEM, BET method(N_2 adsorption)and laser granularity analysis for different synthesis conditions to obtain the optimum conditions for the preparation process. Single-phased, uniform perovskite-type oxides with small particle size were obtained by EDTA sol-gel process with high stability and repeatability, and the process temperature is much lower than that of solid state reaction method.

Electrochemical performance of Al-substituted Li_3V_2(PO_4)_3 cathode materials synthesized by sol-gel method

The effect of Al-substitution on the electrochemical performances of Li3V2(PO4)3 cathode materials was studied.Samples with stoichiometric proportion of Li3AlxV2-x(PO4)3(x=0,0.05,0.10)were prepared by adding Al(NO3)3 in the raw materials of Li3V2(PO4)3.The XRD analysis shows that the Al-substituted Li3V2(PO4)3 has the same monoclinic structure as the un-substituted Li3V2(PO4)3.The SEM images show that Al-substituted Li3V2(PO4)3 has regular and uniform particles.The electrochemical measurements show that Al-substitution can improve the rate capability of cathode materials.The Li3Al0.05V1.95(PO4)3 sample shows the best high-rate performance.The discharge capacity at 1C rate is 119 mA·h/g with 30th capacity retention rate about 92.97%.The electrode reaction reversibility and electronic conductivity are enhanced,and the charge transfer resistance decreases through Al-substitution.The improved electrochemical performances of Al-substituted Li3V2(PO4)3 cathode materials offer some favorable properties for their commercial application.

Progress in Research on Nanometer Al_2O_3 Fabricated by Sol-Gel Method

Nanometer Al_2O_3 is one of new types of functional materials with broad application and development prospects in the future. The basic principle and ways of nanometer Al_2O_3 fabricated using sol-gel technique were introduced, and the factors affecting nanometer Al_2O_3 fabricated using sol-gel method were analyzed. The progress in research on nanometer Al_2O_3 and the application fields of nanometer Al_2O_3 were reviewed. The existing problems and the problems prospect for nanometer Al_2O_3 were pointed out.

Preparation and optical characteristics of ZnO films by chelating sol-gel method

The effect of different annealing temperatures on the structure, morphology,and optical properties of ZnO thin films prepared by the chelating sol-gel method was investigated.Zinc-oxide thin films were coated on quartz glass substrates by dip coating. Zinc nitrate, absoluteethanol, and citric acid were used as precursor, solvent, and chelating agent, respectively. Theresults show that ZnO films derived from zinc-citrate have lower crystallization temperature (below400℃), and that the crystal structure is wurtzite. The films, treated over 500℃, consist ofnano-particles and show to be porous at 600℃. The particle size of the film increases with theincrease of the annealing temperature. The largest particle size is 60 nm at 600℃. The opticaltransmittances related to the annealing temperatures become 90% higher in the visible range. Thefilm shows a starting absorption at 380 nm, and the optical band-gap of the thin film (fired at500℃) is 3.25 eV and close to the intrinsic band-gap of ZnO (3.2 eV).

Intense up-conversion emissions of yb3＋/Dy3＋ co-doped A12O3 nanopowders prepared by non-aqueous sol-gel method＊

yb3＋/Dy3＋ co-doped A1203 nanopowders have been prepared by the non-aqueous sol-gel method and their up- conversion photoluminescence spectra are measured under excitation by a 980-nm semiconductor laser. The results show that there are comparatively abundant spectra of up-conversion emissions centered at 378, 408, 527 and 543, and 663 nm, corresponding to 4C9/2→ 6H13/2, 4C9/2→ 6Hll/2, 4115/2 → 6H13/2, and 4F9/2 →6Hll/2 transitions of Dy3＋, respectively. Two-photon and three-photon processes are involved in ultraviolet, violet, green, and red up-conversion emissions. The energy transition between Yb3＋ and Dy3＋ is discussed.

Preparation of BaCe_(0.5)Zr_(0.4)Y_(0.1)O_(3-α) by Sol-Gel Method and Its Electrical Properties

A precursor of BaCe0.5Zr0.4Y0. 1O3-α electrolytes was synthesized by the sol-gel method and sintered at temperature which were 150 - 250 ℃ lower than by solid state reaction. The AC impedance spectrums of electrolytes were measured by AUTOLAB PGSTA30 electrochemical measuring device at different temperatures. The conductivities of the electrolytes are 1.62×10^-4 - 6.43×10^-3, 2.52×10^-5 - 3.73×10^-3S·cm^-1 in the temperature range of 350-800℃. The activity energies are 0.54 and 0.84 eV. At the same time BaCe0.9Y0.1O3-α was prepared by direct solid state reaction. The conductivity of BaCe0.9Y0.1O3-α is 1 × 10^-4- 4×10^-3 S·cm^-1 and the activation energy is 0.50 eV at the same condition. The results show that conduction of electrolyte prepared by sol-gel method is higher than the one by solid state reaction. As far as BaCe0.9Y0.1O3-α concerned, its conductivity of the Zr-substituted specimens is decreased.

Synthesis and Structure Transformation of Orthorhombic LiMnO2 Cathode Materials by Sol-gel Method

Orthorhombic LiMnO2 cathode materials were synthesized successfully at lower temperature by sol-gel method. When LiMnO2 precursor prepared by sol-gel method was fired in air, the product was a mixture of spinel structure LiMn2O4 and rock-salt structure Li2MnO3, whereas in argon single-phase orthorhombic LiMnO2 could obtain at the range of 750℃ to 920℃. The substitution of Mn by Zn2+ or Co3+ in LiMnO2 led to the structure of LiMnO2 transiting to Qα-LiFeO2. The results of electrochemical cycles indicated that the discharged capacity of orthorhombic-LiMnO2 was smaller at the initial stages, then gradually increased with the increasing of cycle number, finally the capacity stabilized to certain value after about 10th cycles. This phenomenon reveals that there is an activation process for orthorhombic LiMnO2 cathode materials during electrochemical cycles, which is a phase transition process from orthorhombic LiMnO2 to tetragonal spinel Li2Mn2O4. The capacity of orthorhombic LiMnO2 synthesized at lower temperature is larger than that synthesized at high temperature.

Preparation of Ultrafine Tungsten Powder by Sol-Gel Method

Sol-gel method was employed for the preparation of nanoscale tungsten powder. The effects of different preparation conditions on particle size were discussed and the optimum preparation condition was found. The products were characterized by X-ray diffraction, scan electron microscopy and so on. The results show that the intermediate is monoclinic WO3, its particle shape is approximately spherical, and the particle size distribution is narrow. The average particle size is about 60 nm. After deoxidization, WO3 turns into cubic tungsten powder with small particle size （average particle size about 120 nm） and narrow size distribution.

The structural and magnetic properties of barium ferrite powders prepared by the sol-gel method

In this paper, M-type hexagonal barium ferrite powders are synthesized using the sol-gel method. A dried precursor heated in air is analyzed in the temperature range from 50 to 1200 ℃ using thermo-gravimetric analysis and differential scanning calorimetry. The effects of the additives and the cacinating temperature on the magnetic properties are investigated, and the results show that single-phase barium ferrite powders can be formed. After heat-treating at 950 ℃ for 4h with 3 wt% additive, the coercivity and saturation magnetization are found to be 440 Oe and 57.9 emu/g, respectively.

Effect of Annealing on Ferroelectric Properties of Bi_ (3.25)La_(0.75)Ti_3O_ (12) Thin Films Prepared by the Sol-gel Method

Bi3.25La0.75Ti3O12（BLT）thin films were prepared on Pt/Ti/SiO2/Si substrate by the sol-gel method.The effect of annealing on their structures and ferroelectric properties was investigated.The XRD patterns indicate that the BLT films annealed at different temperatures are randomly orientated and the single perovskite phase is obtained at 550℃.The remmant polarization increnses and the coercive field decreases with the annealing temperature increasing.The leakage current density of the BLT films annealed at 700℃ is about 5.8×10^-8A/cm^2 at the electrie field of 250kv/cm.

Preparation of Nanometer-structured TiO_2 Thin Films by Sol-Gel Method

The transparent anatase TiO 2 nanometer thin films were prepared by the sol-gel method on soda-lime glass.X-ray diffraction,thermal analysis and UV-visible spectrophotometer were used to analyze the formation of the phases.Only increasing the heat-treatment time,the average grain size has no obvious change.The mechanism of grain growth in TiO 2 thin film is probably as follows:the grain of coating will become grain core later;TiO 2 sol constantly deposited on the surface of TiO 2 grain and formed membrane with increasing of coating cycle times;TiO 2 grain in the film grow steadily.

Synthesis and Characterization of NASICON Nanoparticles by Sol-gel Method

Na superionic conductor（NASICON） nanoparticles were synthesized by a modified sol-gel method and sintered at a temperature range of 800--1000℃. The performance of the samples was characterized by the analysis methods of X-ray diffraction（XRD）, Fourier transform infrared spectroscopy（FTIR）, and transmission electron microscopy（TEM） as well as conductivity measurement. Compared with those sintered at other temperatures, the NASICON material sintered at 900 ℃ had the best crystalline structure and higher conductivity.

Structural and Electrochemical Properties of Ceria-Doped SnO_2 Prepared by Sol-Gel Method

Tin dioxide (SnO2) and Ce-doped SnO2 were successfully synthesized by sol-gel method and electrochemical properties were studied in cell with Li as counter electrode. The samples were characterized by X-ray diffraction (XRD) and Transmission electron microscopy (TEM). XRD patterns presented that a second phase (CeO) was observed when the Ce content reached 5%. TEM micrograph indicated that Ce-doped SnO2 had a small particle with mean size of 30 nm. The electrochemical properties were also characterized at room temperature, and the results demonstrated that the Ce-doped SnO2 samples exhibited promising electrochemical properties and Ce doped in as-prepared samples plays an important role.