Combinations of Solar Concentrators with Agricultural Plants

A new trend involving the combination of solar concentrators and agricultural plants on the same piece of land offers the possibility of realizing both electricity generation and a good crop harvest.Authors analyze this situation for different countries,including Mexico,and based on authors’experience regarding the development of new solar concentrator prototypes,authors’primary objective was to describe the development of compact,light,and inexpensive solar concentrator prototypes that can be collocated on horizontal roofs.Authors’second objective was to investigate the combination of such solar concentrator prototypes with agricultural plants on the same field.Thus,several studies related to the combination of renewable energy generation and agricultural crops were reviewed.Many such systems involving the combination of PV(Photovoltaic)panels with different types of vegetables exist in the USA,France(lettuce production),Japan(tomato production),India(aloe and corn),northern Italy(maize),Spain and México.

Solid superacid catalysts promote high-performance carbon dots with narrow-band fluorescence emission for luminescence solar concentrators

Facile and efficient method for constructing carbon dots(CDs)with narrow full width at half maximum(FWHM)is a major challenge in the field,and researches on regulating the FWHM of CDs are also rare and scarce.In this work,we delved into the synthesis of CDs with narrow fluorescence emission FWHM(NFEF-CDs)in the m-phenylenediamine(m-PD)/ethanol system,utilizing solid superacid resin as cata-lyst with solvothermal method.The resulting NFEF-CDs exhibit a photoluminescent(PL)emission peak at 521 nm with a narrow FWHM of 41 nm,an absolute PL quantum yield(QY)of 80%,and display excitation-independent PL behavior.Through comprehensive characterization,we identified the protonation of edge amino on NFEF-CDs as the key factor in achieving the narrow FWHM.Subsequently,we validated the broad applicability of solid superacid resins as catalysts for synthesizing CDs with narrow FWHM in the m-PD/ethanol system.Finally,we utilized a self-leveling method to prepare NFEF-CDs film on the surface of poly(methyl methacrylate)(PMMA)substrate and investigated the solid-state fluorescence properties of NFEF-CDs as well as their performance as luminescence solar concentrator(LSC)for photovoltaic conver-sion.The results revealed that the as-prepared LSC exhibit an internal quantum efficiency(η_(int))of 42.39%and an optical efficiency(η_(opt))of 0.68%.These findings demonstrate the promising prospects of NFEF-CDs in the field of LSCs and provide a theoretical basis for their application in photovoltaic conversion.

Solar fuel production through concentrating light irradiation

The climate crisis necessitates the development of non-fossil energy sources.Harnessing solar energy for fuel production shows promise and offers the potential to utilize existing energy infrastructure.However,solar fuel production is in its early stages of development,constrained by low conversion efficiency and challenges in scaling up production.Concentrated solar energy(CSE)technology has matured alongside the rapid growth of solar thermal power plants.This review provides an overview of current CSE methods and solar fuel production,analyzes their integration compatibility,and delves into the theoretical mechanisms by which CSE impacts solar energy conversion efficiency and product selectivity in the context of photo-electrochemistry,thermochemistry,and photo-thermal co-catalysis for solar fuel production.The review also summarizes approaches to studying the photoelectric and photothermal effects of CSE.Lastly,it explores emerging novel CSE technology methods in the field of solar fuel production.

Peak Shaving Strategy of Concentrating Solar Power Generation Based on Multi-Time-Scale and Considering Demand Response

According to the multi-time-scale characteristics of power generation and demand-side response(DR)resources,as well as the improvement of prediction accuracy along with the approaching operating point,a rolling peak shaving optimization model consisting of three different time scales has been proposed.The proposed peak shaving optimization model considers not only the generation resources of two different response speeds but also the two different DR resources and determines each unit combination,generation power,and demand response strategy on different time scales so as to participate in the peaking of the power system by taking full advantage of the fast response characteristics of the concentrating solar power(CSP).At the same time,in order to improve the accuracy of the scheduling results,the combination of the day-ahead peak shaving phase with scenario-based stochastic programming can further reduce the influence of wind power prediction errors on scheduling results.The testing results have shown that by optimizing the allocation of scheduling resources in each phase,it can effectively reduce the number of starts and stops of thermal power units and improve the economic efficiency of system operation.The spinning reserve capacity is reduced,and the effectiveness of the peak shaving strategy is verified.

Solar spectral conversion based on plastic films of lanthanide-doped ionosilicas for photovoltaics:Down-shifting layers and luminescent solar concentrators

The mismatch between the photovoltaic(PV)cells absorption and the solar irradiance on earth is one of the major limitations towards more efficient PV energy conversion.This aspect was addressed by downshifting the solar irradiance on Earth through luminescent down-shifting layers based on lanthanidedoped surface-functionalized ionosilicas(ISs)embedded in poly(methyl methacrylate)(PMMA)coated on the surface of commercial Si-based PV cells.The IS-PMMA hybrid materials exhibit efficient solar radiation harvesting(spectral overlap of^9.5×10^19 photons/(s·m2))and conversion(quantum yield^52%).The direct solar radiation and the down-shifted radiation are partially guided and lost through total internal reflection to the layer edges being unavailable for PV conversion of the coated PV cell.By tuning the down-shifting layer thickness,it also acts as luminescent solar concentrator enabling the collection of the guided radiation by flexible PV cells applied on the borders of the down-shifting layer leading to an enhancement of the PV energy conversion from^5%(in the case of the single-use of the luminescent down-shifting layer)to^13%comparing with the bare PV cell.The overall electrical output of the device resulted in an absolute external quantum efficiency increase of^32%for the optimized Eu^3+-based films in the UV spectral region(compared with the bare PV device,which is among the best values reported so far).

Exciton recycling via InP quantum dot funnels for luminescent solar concentrators

Luminescent solar concentrators (LSC) absorb large-area solar radiation and guide down-converted emission to solar cells for electricity production. Quantum dots (QDs) have been widely engineered at device and quantum dot levels for LSCs. Here, we demonstrate cascaded energy transfer and exciton recycling at nanoassembly level for LSCs. The graded structure composed of different sized toxic-heavy-metal-free InP/ZnS core/shell QDs incorporated on copper doped InP QDs, facilitating exciton routing toward narrow band gap QDs at a high nonradiative energy transfer efficiency of 66%. At the final stage of non-radiative energy transfer, the photogenerated holes make ultrafast electronic transitions to copper-induced mid-gap states for radiative recombination in the near-infrared. The exciton recycling facilitates a photoluminescence quantum yield increase of 34% and 61% in comparison with semi-graded and ungraded energy profiles, respectively. Thanks to the suppressed reabsorption and enhanced photoluminescence quantum yield, the graded LSC achieved an optical quantum efficiency of 22.2%. Hence, engineering at nanoassembly level combined with nonradiative energy transfer and exciton funneling offer promise for efficient solar energy harvesting.

Red-emitting tetraphenylethylene derivative with aggregation-induced enhanced emission for luminescent solar concentrators:A combined experimental and density functional theory study

This study examines the use of an aggregation-induced enhanced emission fluorophore(TPE-MRh)to prepare red-emitting luminescent solar concentrators(LSCs)based on poly(methyl methacrylate)(PMMA)and poly(cyclohexyl methacrylate)(PCMA).TPE-MRh is a tetraphenylethylene(TPE)derivative bearing two dimethylamino push groups and a 3-methyl-rhodanine pull moiety,with absorption maxima at around 500 nm and fluorescence peak at 700 nm that strongly increases in solid-state.TPE-MRh displays a typical crystallizationinduced enhanced emission that has been rationalized by modeling the compound behavior in solution and solid-state via density functional theory calculations with the inclusion of the environment.TPE-MRh dispersed into 5×5 cm2 polymer films with a thickness of 25±5μm has revealed a partial fluorescence quenching with fluorophore content.Quantum yields(QYs)below 10%for the 2 wt.%of doping have been addressed to the formation of less emissive micro-sized clusters of fluorophores.PMMA slabs with the same surface size but 3 mm of thickness and 200 ppm of TPE-MRh have provided QY of 36.5%thanks to the attenuation of the detrimental effects of fluorophore aggregation.This feature is reflected in the LSCs performance,with devices achieving the largest power collected by the photovoltaic cell.

Research progress on protective coatings against molten nitrate salts for thermal energy storage in concentrating solar power plants

Concentrating solar power(CSP) has garnered considerable global attention as a reliable means of generating bulk electricity, effectively addressing the intermittent nature of solar resources.The integration of molten salt technology for thermal energy storage(TES) has further contributed to the growth of CSP plants;however, the corrosive nature of molten salts poses challenges to the durability of container materials, necessitating innovative corrosion mitigation strategies.This review summarizes scientific advancements in high-temperature anticorrosion coatings for molten nitrate salts, highlighting the key challenges and future trends.It also explores various coating types, including metallic, ceramic, and carbon-based coatings, and compares different coating deposition methods.This review emphasizes the need for durable coatings that meet long-term performance requirements and regulatory limitations, with an emphasis on carbon-based coatings and emerging nanomaterials.A combination of multiple coatings is required to achieve desirable anticorrosion properties while addressing material compatibility and cost considerations.The overall goal is to advance the manufacturing, assembly, and performance of CSP systems for increased efficiency, reliability, and durability in various applications.

Improving photoreduction of CO2 with water to CH4 in a novel concentrated solar reactor

COphotoreduction is an attractive process which allows the storage of solar energy and synthesis of solar fuels. Many different photocatalytic systems have been developed, while the alternative photo-reactors are still insufficiently investigated. In this work, photoreduction of COwith HO into CHwas investigated in a modified concentrating solar reactor, using TiOand Pt/TiOas the catalysts. The TiOand Pt/TiOsamples were extensively characterized by different techniques including powder X-ray diffraction（XRD）, Nadsorption/desorption and UV–vis absorption. The catalytic performance of the TiOand Pt/TiOsamples in the gas phase was evaluated under unconcentrated and concentrated Xe-lamp light and nature solar light with different concentrating ratios. Various parameters of the reaction system and the catalysts were investigated and optimized to maximize the catalytic performance of COreduction system. Compared with the normal light irradiation, the TiOand Pt/TiOsamples show higher photocatalytic activity（about 6–7 times） for reducing COinto CHunder concentrated Xe-lamp light and nature solar light. In the range of experimental light intensity, it is found that the concentration of the light makes it suitable for the catalytic reaction, and increases the utilization efficiency of the TiOand Pt/TiOsamples while does not decrease the quantum efficiency.

Natural gas pyrolysis in double-walled reactor tubes using thermal plasma or concentrated solar radiation as external heating source

The thermal pyrolysis of natural gas as a clean hydrogen production route is examined. The concept of a double-walled reactor tube is proposed and implemented. Preliminary experiments using an external plasma heating source are carried out to validate this concept. The results point out the efficient CH4 dissociation above 1850 K （CH4 conversion over 90%） and the key influence of the gas residence time. Simulations are performed to predict the conversion rate of CH4 at the reactor outlet, and are consistent with experimental tendencies. A solar reactor prototype featuring four independent double-walled tubes is then developed. The heat in high temperature process required for the endothermic reaction of natural gas pyrolysis is supplied by concentrated solar energy. The tubes are heated uniformly by radiation using the blackbody effect of a cavity-receiver absorbing the concentrated solar irradiation through a quartz window. The gas composition at the reactor outlet, the chemical conversion of CH4, and the yield to H2 are determined with respect to reaction temperature, inlet gas flow-rates, and feed gas composition. The longer the gas residence time, the higher the CH4 conversion and H2 yield, whereas the lower the amount of acetylene. A CH4 conversion of 99% and H2 yield of about 85% are measured at 1880 K with 30% CH4 in the feed gas （6 L/min injected and residence time of 18 ms）, A temperature increase from 1870 K to 1970 K does not improve the H2 yield.

Application of Model Predictive Control Based on Kalman Filter in Solar Collector Field of Solar Thermal Power Generation

There are two prominent features in the process of temperature control in solar collector field.Firstly,the dynamic model of solar collector field is nonlinear and complex,which needs to be simplified.Secondly,there are a lot of random and uncontrollable,measurable and unmeasurable disturbances in solar collector field.This paper uses Taylor formula and difference approximation method to design a dynamic matrix predictive control(DMC)by linearizing and discretizing the dynamic model of the solar collector field.In addition,the purpose of controlling the stability of the outlet solar field salt temperature is achieved by adjusting the mass flow of molten salt.In order to further improve the ability of the system to suppress unmeasured disturbances,a steady-state Kalman filter is designed to estimate state variables,so that the system has better stability and robustness.The simulation verification results show that the DMC control system based on Kamlan filtering has better control effect than the traditional DMC control system.In the case of large fluctuations in solar radiation intensity and consideration of undetectable interference,the overshoot of the system is reduced by 4%and the rise time remains unchanged.

High-temperature Thermal Properties and Wear Behavior of Basalt as Heat Storage Material for Concentrated Solar Power Plants

The microstructures,components,thermal stability,specific heat capacity and thermal conductivity of basalt sample were studied.Besides,as a comprehensive result of thermal expansion and contraction process,both the friction coefficient and wear rate of the basalt sample were also characterized.Our results indicate that basalt is an excellent candidate to be used as thermal energy storage material for concentrated solar power plants,and also provide a strategy for solar energy utilization in volcanic area with excellent geographical environment.

Economic analysis of solar energy development in North Africa

The economic analysis of solar energy development is the basis of promoting the solar energy planning in north Africa and realizing the clean energy power transmission among continents. In this paper, the cost development trend of photovoltaic(PV) power and concentrating solar power(CSP) generation is analyzed, and the levelized cost of energy(LCOE) of solar power generation is forecasted. Then, taking the development of Tunisian solar energy as an example in the context of transcontinental transmission, PV power with energy storage and PV-CSP power generation are given as two kinds of development plan respectively. The installed capacity configurations of the two schemes are given with production simulation method, and comprehensive LCOE are calculated. The studies show that based on the LCOE forecast value, the LCOE of PV-CSP combined power generation will decrease when the annual utilization hours of transmission channel is increased. It can be chosen as one of important mode of the North Africa solar energy development.

Thermal modeling and the optimized design of metal plate cooling systems for single concentrator solar cells

A metal plate cooling model for 400~ single concentrator solar cells was established. The effects of the thickness and the radius of the metal plate, and the air environment on the temperature of the solar cells were analyzed in detail. It is shown that the temperature of the solar cells decreased sharply at the beginning, with the increase in the thickness of the metal plate, and then changed more smoothly. When the radius of the metal plate was 4 cm and the thickness increased to 2 mm or thicker, the temperature of the solar cell basically stabilized at about 53℃. Increasing the radius of the metal plate and the convective transfer coefficient made the temperature of the solar cell decrease remarkably. The effects of A1 and Cu as the metal plate material on cooling were analyzed contrastively, and demonstrated the superiority of A1 material for the cooling system. Furthermore, considering cost reduction, space holding and the stress of the system, we optimized the structural design of the metal plate. The simulated results can be referred to the design of the structure for the metal plate. Finally, a method to devise the structure of the metal plate for single concentrator solar cells was given.

Thermo-Economic Optimization of Solar Thermal Devices by Coherent Integration of Technologies

Radiation is a form of energy where the angular variable of the direction of its photons has a primary importance, particularly for radiation concentration processes, which are essential tools to reach high temperatures from radiation beams (as the solar ones) with moderate intensities. Solar radiation cannot be used directly to feed thermodynamic cycles, and optical concentration must be applied to that goal. In general, reflection from mirrors is preferred to refraction by lenses in this case, because they have less optical aberrations. Concentration conveys very high temperatures in the receiver. However, the higher the temperature, the lower the efficiency of the solar thermal apparatus. Besides that, economy also suffers quite a lot when going to very high concentration factors, which is one of the main burdens in the development of Solar Thermal Energy. A new configuration of solar radiation concentrator is presented. It includes a salient innovation in the way the mirrors are given the right curvature by mechanical forces. Those mirrors are originally flat and do not need any special thermal treatment for this purpose. The whole device concept has been guided by the principle of thermoeconomic coherence, which requires similar efforts in all degrees of freedom that have strong influence in the performance and cost of the system. The paper shows the decision tree that has oriented the project, following the principle of equilibrium in efforts, which leads to a design window of moderate values in the main variables. The prototype of this new configuration has already been built, and the first stage of research is considered to be finished, because the prototype has shown excellent conditions to include selected (fitting) technologies at a very low cost.

Thermal modeling optimization and experimental validation for a single concentrator solar cell system with a heat sink

A single concentrator solar cell model with a heat sink is established to simulate the thermal performance of the system by varying the number, height, and thickness of fins, the base thickness and thermal resistance of the thermal conductive adhesive. Influence disciplines of those parameters on temperatures of the solar cell and heat sink are obtained. With optimized number, height and thickness of fins, and the thickness values of base of 8, 1.4 cm, 1.5 mm, and 2 mm, the lowest temperatures of the solar cell and heat sink are 41.7 ~C and 36.3 ~C respectively. A concentrator solar cell prototype with a heat sink fabricated based on the simulation optimized structure is built. Outdoor temperatures of the prototype are tested. Temperatures of the solar cell and heat sink are stabilized with time continuing at about 37 ℃-38 ℃ and 35 ℃-36 ℃respectively, slightly lower than the simulation results because of effects of the wind and cloud. Thus the simulation model enables to predict the thermal performance of the system, and the simulation results can be a reference for designing heat sinks in the field of single concentrator solar cells.

Production of metallic nanopowders(Mg,Al)by solar carbothermal reduction of their oxides at low pressure

The carbothermal reduction of MgO and Al_(2)O_(3) in argon flow at low pressure allows to lower the onset temperature of metal vapor formation.Thermodynamic calculations indicate that metal formation begins at 1400 and 1700 K for a primary vacuum(1000 Pa),respectively,for Mg and Al.In the experimental section,concentrated solar energy was used for the process heating in order to favor energy savings.The products of the reaction between MgO or Al_(2)O_(3) and 2 varieties of carbon(graphite,carbon black)in flowing argon atmosphere at a total pressure of around 1000 to 1600 Pa were studied using X-ray diffraction,and microstructure observations revealed the formation of metallic nanopowders with some by-products.Metallic conversions close to 45 wt%and 52 wt%,respectively,for Mg and Al,were obtained.The low conversion yield of the carbothermal reduction of MgO can be attributed to a backward reaction reforming MgO powder and to a sintering process between oxide particles at high temperature.Aluminum production challenge is to avoid formation of undesired by-products:Al_(2)O,Al_(4)C_(3) and Al-oxycarbides.Advantages and weaknesses of the used process are described and some improvements are proposed to increase metallic yields.

Modulating a Solar Parabolic Dish to Produce Boiled Water

A two-meter parabolic solar concentration dish has been modulated to produce boiled water over 100℃ for various purposes of central heating services. For an effective performance, the system required both continuous exposure of the dish to sunlight during the day time as well as to an electric control circuit （tracking system）. The amount of the potable water was dependent particularly on the accurate centering of the system which could increase upon preheating. This system has therefore been possible to heat up water at home via increasing the temperature in hot tank by both covering the hot water tank and isolating it from the surroundings using insulators. Applications of a successful parabolic solar concentration has also been designed to provide desalinated water for domestic usage which operates with temperatures higher than other types of the solar radiation for the future.

Enhanced efficiency in Concentrated Parabolic Solar Collector(CPSC) with a porous absorber tube filled with metal nanoparticle suspension

In this study, effects of different nanoparticles and porosity of absorber tube on the performance of a Concentrating Parabolic Solar Collector(CPSC) were investigated. A section of porous-filled absorber tube was modeled as a semi-circular cavity under the solar radiation which is filled by nanofluids and the governing equations were solved by FlexPDE numerical software. The effect of four physical parameters, nanoparticles type, nanoparticles volume fraction(φ), Darcy number(Da) and Rayleigh number(Ra), on the Nusselt number(Nu) was discussed. It turns out that Cu nanoparticle is the most suitable one for such solar collectors, compared to the commonly used Fe_3O_4, Al_2O_3, TiO_2.With the increased addition of Cu nanoparticles all the parameters φ, Da and Ra shows a significant increase against the Nu, indicates the enhanced heat transfer in such cases. As a result, low concentration of Cu nanoparticle suspension combined with porous matrix was supposed to be beneficial for the performance enhancement of concentrating parabolic solar collector.

Concentrating Solar Power in Europe, the Middle East and North Africa： Achieving Its Potential

CSP （concentrating solar power） is a commercially available renewable energy technology capable of harnessing the immense solar resource in southern Europe, the MENA region （Middle East and North Africa）, and elsewhere. This paper summarises the findings of a study by the European Academies Science Advisory Council which has examined the current status and development challenges of CSP, and consequently has evaluated the potential contribution of CSP in Europe and the MENA region to 2050. It identifies the actions that will be required by scientists, engineers, policy makers, politicians, business and investors alike, to enable this vast solar resource to make a major contribution to establishing a sustainable energy system. The study concludes that cost reductions of 50%-60% in CSP electricity may reasonably be expected in the next 10-15 years, enabling the technology to be cost competitive with fossil-fired power generation at some point between 2020 and 2030. Incorporation of storage delivers added value in enabling CSP to deliver dispatchable power. Incentive schemes will be needed in Europe and MENA countries to enable this point to be achieved. Such schemes should reflect the true value of electricity to the grid, effectively drive research and development, and ensure transparency of performance and cost data.