CO_(2) mineralization by typical industrial solid wastes for preparing ultrafine CaCO_(3): A review

Mineral carbonation is a promising CO_(2) sequestration strategy that can utilize industrial wastes to convert CO_(2) into high-value CaCO_(3).This review summarizes the advancements in CO_(2) mineralization using typical industrial wastes to prepare ultrafine CaCO_(3).This work surveys the mechanisms of CO_(2) mineralization using these wastes and its capacities to synthesize CaCO_(3),evaluates the effects of carbonation pathways and operating parameters on the preparation of CaCO_(3),analyzes the current industrial application status and economics of this technology.Due to the large amount of impurities in solid wastes,the purity of CaCO_(3) prepared by indirect methods is greater than that prepared by direct methods.Crystalline CaCO_(3) includes three polymorphs.The polymorph of CaCO_(3) synthesized by carbonation process is determined the combined effects of various factors.These parameters essentially impact the nucleation and growth of CaCO_(3) by altering the CO_(2) supersaturation in the reaction system and the surface energy of CaCO_(3) grains.Increasing the initial pH of the solution and the CO_(2)flow rate favors the formation of vaterite,but calcite is formed under excessively high pH.Vaterite formation is favored at lower temperatures and residence time.With increased temperature and prolonged residence time,it passes through aragonite metastable phase and eventually transforms into calcite.Moreover,polymorph modifiers can decrease the surface energy of CaCO_(3) grains,facilitating the synthesis of vaterite.However,the large-scale application of this technology still faces many problems,including high costs,high energy consumption,low calcium leaching rate,low carbonation efficiency,and low product yield.Therefore,it is necessary to investigate ways to accelerate carbonation,optimize operating parameters,develop cost-effective agents,and understand the kinetics of CaCO_(3) nucleation and crystallization to obtain products with specific crystal forms.Furthermore,more studies on life cycle assessment(LCA)should be conducted to fully confirm the feasibility of the developed technologies.

Bird’s-eye view of recycled solid wastes in road engineering

Recent trends in road engineering have explored the potential of incorporating recycled solid wastes into infrastructures that including pavements,bridges,tunnels,and accessory structures.The utilization of solid wastes is expected to offer sustainable solutions to waste recycling while enhancing the performance of roads.This review provides an extensive analysis of the recycling of three main types of solid wastes for road engineering purposes:industrial solid waste,infrastructure solid waste,and municipal life solid waste.Industrial solid wastes suitable for road engineering generally include coal gangue,fly ash,blast furnace slag,silica fume,and steel slag,etc.Infrastructure solid wastes recycled in road engineering primarily consist of construction&demolition waste,reclaimed asphalt pavements,and recycled cement concrete.Furthermore,recent exploration has extended to the utilization of municipal life solid wastes,such as incinerated bottom ash,glass waste,electronics waste,plastic waste,and rubber waste in road engineering applications.These recycled solid wastes are categorized into solid waste aggregates,solid waste cements,and solid waste fillers,each playing distinct roles in road infrastructure.Roles of solid waste acting aggregates,cements,and fillers in road infrastructures were fully investigated,including their pozzolanic properties,integration effects to virgin materials,modification or enhancement solutions,engineering performances.Utilization of these materials not only addresses the challenge of waste management but also offers environmental benefits aiming carbon neutral and contributes to sustainable infrastructure development.However,challenges such as variability in material properties,environmental impact mitigation,secondary pollution to environment by leaching,and concerns regarding long-term performance need to be further addressed.Despite these challenges,the recycled solid wastes hold immense potential in revolutionizing road construction practices and fostering environmental stewardship.This review delves into a bird’seye view of the utilization of recycled solid wastes in road engineering,highlighting advances,benefits,challenges,and future prospects.

Start-up performances of dry anaerobic mesophilic and thermophilic digestions of organic solid wastes

Two dry anaerobic digestions of organic solid wastes were conducted for 6 weeks in a lab-scale batch experiment for investigating the start-up performances under mesophilic and thermophilic conditions. The enzymatic activities, i.e., β-glucosidase, N-α-benzoyl-Largininamide （BAA）-hydrolysing protease, urease and phosphatase activities were analysed. The BAA-hydrolysing protease activity during the first 2-3 weeks was low with low pH, but was enhanced later with the pH increase. β-Glucosidase activity showed the lowest values in weeks 1-2, and recovered with the increase of BAA-hydrolysing protease activity. Acetic acid dominated most of the total VFAs in thermophilic digestion, while propionate and butyrate dominated in mesophilic digestion. Thermophilic digestion was confirmed more feasible for achieving better performance against misbalance, especially during the start-up period in a dry anaerobic digestion process.

A review of the synthesis and application of zeolites from coal-based solid wastes

Zeolite derived from coal-based solid wastes(coal gangue and coal fly ash)can overcome the environmental problems caused by coal-based solid wastes and achieve valuable utilization.In this paper,the physicochemical properties of coal gangue and coal fly ash are introduced.The mechanism and application characteristics of the pretreatment processes for zeolite synthesis from coal-based solid wastes are also introduced.The synthesis processes of coal-based solid waste zeolite and their advantages and disadvantages are summarized.Furthermore,the application characteristics of various coal-based solid waste zeolites and their common application fields are illustrated.Finally,we propose an alkaline fusion-assisted supercritical hydrothermal crystallization as an efficient method for synthesizing coal-based solid waste zeolites.In addition,more attention should be given to the recycling of alkaline waste liquid and the application of coal-based solid waste zeolites in the field of volatile organic compound adsorption removal.

Preparation and characterization of high-strength calcium silicate boards from coal-fired industrial solid wastes

To realize the comprehensive utilization of coal-fired industrial solid wastes, a novel high-strength board was prepared from calcium silicate slag, fly ash, and flue gas desulfurization(FGD) gypsum. The changes in mineral phases, chemical structure, and morphology during hydration were investigated by X-ray diffraction(XRD), Fourier transform infrared spectroscopy(FTIR), and scanning electron microscopy(SEM). A traditional board made from quartz and lime was prepared as a reference. The novel board not only consumes a lot of solid wastes, but also meets the strength requirement of the class-five calcium silicate board according to the Chinese Standard JC/T 564.2—2008. Microanalysis showed that hydrated calcium silicate gel(C-S-H(I)), ettringite, tobermorite, and xonotlite were successively generated in the novel board by synergistic hydration of the mixed solid wastes. The board strength was improved by the formation of tobermorite and xonotlite but decreased by unhydrated quartz. It was demonstrated that quartz was not completely hydrated in the traditional board. As a result, the flexural strength of the traditional board was much lower than that of the novel board.

Volatilization of heavy metals during incineration of municipal solid wastes

Incineration experiments with MSW, which had been impregnated with heavy metals, were presented to obtain information on the volatilization behavior of the elements cadmium(Cd), lead(Pb), and zinc(Zn) under different conditions. Experiments were carried out in a bubbling fluid bed system connected to a customized inductively coupled plasma optical emission spectroscopy(ICP-OES) for analyzing metals in the flue gas. The results indicated that the combustion temperature, the gas atmosphere, and the chlorine content in the flue gas could affect the volatilization behavior of heavy metals. In the fluidized bed combustion, a large surface area was provided by the bed sand particles, and they may act as absorbents for the gaseous ash-forming compound. Comparer with the metals Cd and Pb, the vaporization of Zn was low. The formation of stable compounds such as ZnO·Al 2O 3 could greatly decrease the metals volatilization. The presence of chlorine would enhance the volatilization of heavy metals by increasing the formation of metal chlorides. However, when the oxygen content was high, the chlorinating reaction was kinetically hindered, which heavy metals release would be delayed.

Formation cause,composition analysis and comprehensive utilization of rare earth solid wastes

Based on practical situation of rare earth industrial chain,production process and rare earth materials that could produce solid wastes on batch were discussed.Formation cause,formation volume,composition analysis and comprehensive utilization of the solid wastes of rare earth hydrometallurgy slag,electrolysis slag,Fe-based rare earth permanent magnetic materials,Co-based rare earth permanent magnetic materials,rare earth hydrogen storage materials,rare earth polishing powders and rare earth catalysts were ...

FORMATION MECHANISMS AND CONTROL STRATEGIES FOR DIOXINS IN INCINERATION PROCESS OF MUNICIPAL SOLID WASTES

Dioxins, which are of the most toxic materials on the earth, are principal emitted from waste incineration process. The molecular structures, toxicity parameters, such as toxicity equivalency factor, tolerable daily intake and physic-chemical properties of dioxins are briefly summarized. Three formation mechanisms of dioxins in waste incineration process, namely as de novo synthesis, mechanisms involving small organic molecular as precursors and homogenous gas phase reaction mechanism are alto reviewed. The influencing factors for dioxins formation during waste incineration process are also discussed. Three major methods for reducing dioxins emission from waste incineration process are discussed based upon the formation mechanisms and influencing factors. A new waste incineration process with low dioxins emission and low hydrogen chloride corrosion has been proposed based on multi- stage unit operation principal according to formation mechanisms of dioxins and potential production location in waste incinerators.

Breakthrough Technologies for the Biorefining of Organic Solid and Liquid Wastes

Organic solid and liquid wastes contain large amounts of energy, nutrients, and water, and should not be perceived as merely waste. Recycling, composting, and combustion of non-recyclables have been practiced for decades to capture the energy and values from municipal solid wastes. Treatment and disposal have been the primary management strategy for wastewater. As new technologies are emerging, alternative options for the utilization of both solid wastes and wastewater have become available. Considering the complexity of the chemical, physical, and biological properties of these wastes, multiple technologies may be required to maximize the energy and value recovery from the wastes. For this purpose, biorefin- ing tends to be an appropriate approach to completely utilize the energy and value available in wastes. Research has demonstrated that non-recyclable waste materials and bio-solids can be converted into usable heat, electricity, fuel, and chemicals through a variety of processes, and the liquid waste streams have the potential to support crop and algae growth and provide other energy recovery and food production options. In this paper, we propose new biorefining schemes aimed at organic solid and liquid wastes from municipal sources, food and biological processing plants, and animal production facilities. Four new breakthrough technologies-namely, vacuum-assisted thermophilic anaerobic digestion, extended aquaponics, oily wastes to biodiesel via glycerolysis, and microwave-assisted thermochemical conversion-can be incorporated into the biorefining schemes, thereby enabling the complete utilization of those wastes for the production of chemicals, fertilizer, energy （biogas, syngas, biodiesel, and bio-oil）, foods, and feeds, and resulting in clean water and a significant reduction in pollutant emissions.

Generation, Characterization and Management Practices of Household Solid Wastes in Cowfield, Paynesville City, Liberia

The success of any waste management system requires accurate and up-to-date data on quantity, composition of waste. Waste generation data from household are needed to address issues relating to municipal solid wastes such as management method, performance improvement, policy, regional and local planning, administrative, cost accounting, design and operation of landfill facilities and environmental quality. This study was conducted to provide empirical data on generation rates, quantity and composition, management practices, challenges and strategies from urban household. Waste collection, weighing, questionnaires survey and field observation were methods used during the study. Waste was collected and weighed from 60 households using multi-stage sampling technique for seven days. Questionnaires were analyzed using Statistical Package for Social Sciences version 20 and Excel. A total of 1125.2 kg of waste was recorded. The average household waste generation was 3 kg per day with per capita generation rate of 0.41 kg/cap/day. The compositional analysis showed that Organic (53%), Plastic (11%), Textile (6%), Metal (2%), Glass (1%), Paper and Cardboard 4% and others (22%). Solid waste management practices are very rudimentary. Burning (53.7%) and Open Dumping (30%) were found to be the most commonly used method of disposal with very limited collection service (33.3%) and segregation. The most challenges faced by households were communal disposal area (66.7%) and waste service providers (21.7%) storage bins (11.6%). Waste to energy (48.3%) and compositing (23.3%) were the most considered option for waste management by the respondents.

High Quality Bio-Oil Obtained from Catalyzed Pyrolysis of Olive Mill Solid Wastes in a Bi-Functional Reactor

Olive Mill Solid Wastes (OMSW) released in nature without any treatment is a major environmental problem in the Mediterranean region. In this work, the catalyzed pyrolysis of OMSW has been investigated. A catalyst based on SBA-15 mesoporous silica doped with chromium ferrite nanoparticles was prepared by the double solvent technique (DS). The prepared catalyst was characterized by scanning electron microscopy (SEM), Wide and Small Angle X-ray Scattering (WAXS, SAXS), Energy Dispersive X-ray (EDX) and FT-IR spectroscopies. Reverse spinel chromium ferrite nanoparticles were located inside the SBA-15 pores as confirmed by SEM images. The obtained catalyst was tested for pyrolysis reactions of OMSW. Several parameters were studied to optimize the conditions of the pyrolysis reaction in order to increase the bio-oil conversion yield. The GC-MS results demonstrated that the quality of the obtained bio-oil was improved by decreasing the quantity of phenolic and oxygenated components as well as the size of the obtained molecules. The produced bio-oil from pyrolysis of OMSW is identical to that obtained from the pyrolysis of commercial cellulose under the same conditions. A 37% conversion yield of bio-oil was obtained for the best conditions.

Microstructural analysis of marl stabilized with municipal solid waste and nano-MgO

Municipal solid waste(MSW)is accumulating over elapsed time across the world,and it is observed in many projects associated with weak soils,such as marl.Therefore,effective solutions to the environmental problem are essential.Conventional techniques for stabilizing marl generally use substances such as lime and cement,which could exacerbate pollution.For this,some new stabilizers,e.g.nano-MgO,are used.There are large quantities of marls and MSW in Shiraz City,Iran.The present study aims to evaluate the feasibility of using nano-MgO as a green low-carbon binder to remove MSW from the environment and make construction projects more cost-effective.Consolidated drained shear tests were conducted to evaluate the mechanical behaviors of the nano-MgO treated marl specimens at high normal stresses.The marl specimens containing MSW percentages of 15%,25%,35%,and 45%and nano-MgO percentages of 0.25%,0.5%,0.75%,and 1%,were used.It is found that the marl containing 15%and 25%MSW and 0.5%nano-MgO at 28-d curing can perform cation exchange and form new cementitious products.The soils with merely MSW show good performance due to the removal of the kaolinite and the formation of brucite.However,the soil with 25%MSW and 0.5%nano-MgO shows the same strength enhancement as the specimen with the optimal nano-MgO(0.75%)through the formation of dolomite,with a 20.59%increase in strain energy(SE).

Effects of Using Municipal Solid Waste Incineration Tailings as Lightweight Aggregate on the Mechanical Properties of Specified Density Concrete

Municipal solid waste incineration tailings were used as lightweight aggregate(MSWIT-LA)in the preparation of specified density concrete to study the effects on compressive strength,axial compressive strength,flexural strength,microhardness,total number of pores,pore area,and pore spacing.The results showed that the internal curing and morphological effects induced by an appropriate quantity of MSWIT-LA improved the compressive response of specified density concrete specimens,whereas an excessive quantity of MSWIT-LA significantly reduced their mechanical properties.An analysis of pore structure indicated that the addition of MSWIT-LA increased the total quantity of pores and promoted cement hydration,resulting in a denser microstructure than that of ordinary concrete.The results of a principal component analysis showed that the mechanical response of specified density concrete prepared with 25%MSWIT-LA was superior to that of an equivalent ordinary concrete.It was therefore concluded that MSWIT-LA can be feasibly applied to achieve excellent specified density concrete properties while utilising municipal solid waste incineration tailings to protect the environment and alleviate shortages of sand and gravel resources.

Partial Replacement of Cement by Solid Wastes as New Materials for Green Sustainable Construction Applications

The manufacturing of ordinary Portland cement is an energy-intensive process that results in pollution and CO2 emissions,among other issues.There is a need for an environmentally friendly green concrete substitute.Waste products from a variety of sectors can be recycled and used as a green concrete substitute.This decreases the environmental effects of concrete manufacturing as well as energy consumption.The use of solid waste materials for green building is extremely important now and in the future.Green concrete is also in its infancy in terms of manufacturing and application.Academics must intervene by encouraging business implementation.The aim of this review paper is to raise awareness about the importance of repurposing recycled materials and to highlight new technologies for producing green,sustainable concrete.

The Application of Solid Waste in Thermal Insulation Materials: A Review

As socioeconomic development continues,the issue of building energy consumption has attracted significant attention,and improving the thermal insulation performance of buildings has become a crucial strategic measure.Simultaneously,the application of solid waste in insulation materials has also become a hot topic.This paper reviews the sources and classifications of solid waste,focusing on research progress in its application as insulation materials in the domains of daily life,agriculture,and industry.The research shows that incorporating household solid waste materials,such as waste glass,paper,and clothing scraps into cementitious thermal insulation can significantly reduce the thermal conductivity of the materials,leading to excellent thermal insulation properties.Insulation materials prepared from agricultural solid waste,such as barley straw,corn stalk,chicken feather,and date palm fibers,possess characteristics of lightweight and strong thermal insulation.Industrial solid waste,including waste tires,iron tailings,and coal bottom ash,can also be utilized in the preparation of insulation materials.These innovative applications not only have positive environmental significance by reducing waste emissions and resource consumption,but also provide efficient and sustainable insulation solutions for the construction industry.However,to further optimize the mix design and enhance the durability of insulation materials,continuous research is required to investigate the mechanisms through which solid waste impacts the performance of insulation materials.

China's first plasma pyrolysis system for treating solid wastes

A research team from the CAS Institute of Mechanics has been recently successful in developing China’s first plasma pyrolysis system for the treatment of solid chemical wastes.

Household Solid Waste Awareness and Practices among Residents of Windhoek, Namibia

This study explores household solid waste management (HSWM) practices and awareness among residents of Windhoek West, a rapidly urbanizing constituency in the Khomas Region of Namibia. Employing a descriptive methodology, the research investigates the interplay between public awareness, regulatory frameworks, and the availability of waste management facilities to assess their impact on waste management behaviors. Our findings indicate significant gaps in both knowledge and infrastructure that hinder effective waste management. The study reveals that while there is a high willingness among residents to engage in recycling and waste reduction, actual practices are limited due to inadequate facilities and lack of stringent enforcement of waste policies. This research identifies key factors that influence waste management practices, including demographic characteristics and access to waste management facilities. It also proposes actionable strategies such as expanding recycling and sorting facilities, enhancing educational campaigns tailored to local needs, and implementing regular enforcement mechanisms. These strategies are aimed at improving compliance with waste management protocols and fostering a culture of environmental responsibility. The results of this investigation show the critical role of ongoing education and infrastructural improvement in bridging existing knowledge gaps and facilitating effective waste management practices. This research lays a foundational step toward enhancing sustainable urban development and effective waste management in Windhoek, providing valuable insights for policymakers, community leaders, and stakeholders engaged in urban environmental management.

The Impact of Solid Waste Generation, Storage and Separation Practices among Households on the Environment in Freetown

As urbanization and population growth continue to increase in Freetown, due to changes in economic, social, environmental, political, and demographic factors, the municipal solid waste (MSW) generation also continues to increase, making its management difficult for the municipal authority. Efficient separation and storage of solid waste at the source of generation can boost resource and energy recovery from MSW. This study examines the municipal solid waste management (MSWM) process, focusing on generation, storage and separation practices among households and their impact on the environment in Freetown. It emphasizes the inclusion of MSWM programs in primary schools to raise public awareness, the implementation of effective waste management practices, and the enforcement of related policies to enhance the MSWM sector, contributing to sustainable MSWM in Freetown. By utilizing both qualitative and quantitative methods, 393 structured questionnaires were administered across three selected sections to collect data on household solid waste storage and separation practices. The analysis employed descriptive statistics, using Origin-Pro9 and MS Excel. The findings show that with a population of 1.53 million people in Freetown, the per capita solid waste generation is 0.58 kg per day. The findings also show that 97% of the households have storage facilities as a result of the increase in awareness and education about the proper storage of solid waste. However, 96% of respondents do not practice separation of solid waste at the source of generation, which has become a concern among researchers in Sierra Leone. Additionally, 88% of respondents are unaware of ISWM principles, with only 12% aware, most of whom have received some education on proper solid waste management. The study recommends improving MSWM in Freetown to protect public health and the environment.

Assessment of the Characteristics of the Municipal Solid Waste Compost in Lebanon

Waste management is crucial due to the fast increase of human population, causing an increase in solid waste generation which if not properly managed causes environmental problems. Around 57% of the wastes generated from homes are made up of green material (fruits, vegetables…). Thus, reusing and recycling green wastes through composting is one way of reducing the waste load to landfills. Composting is the transformation of raw organic materials into organic soil amendments that provide nutrients to crops and enhance the tilth, fertility, and productivity of soils. Aerobic windrow composting system at Sukomi Greensite facility located at Karantina is performed, where materials biodegrade under controlled conditions to produce compost. However, assessment of the quality of the compost is fundamental in order to determine its usages. Thus, regular testing of physical, chemical and biological parameters was performed for adequate monitoring purposes. The basic objective of this study was to determine the characteristics of the Lebanese municipal solid waste compost on a yearly basis and compare these characteristics amongst the years. Hence, each parameter was tested and compared to the BNQ international Canadian standards for proper classification of the compost and adequate identification of its usages. The preliminary data obtained were statistically diagnosed through principal component analysis by Spadv55 software. All the data reflected the normal content value of the studied parameters with minor differences between the years except for year 2007 which demonstrated higher levels of Potassium, Phosphate, Lead and Cadmium. The characteristics of the compost enabled it to be used as a soil amendment on all types of agricultural and landscape commodities at the adequate dosages and proper timing. This data will additionally reflect the efficiency of the solid waste management practices adopted via highlighting the importance of the implementation of the integrated solid waste management practices.

Solid Waste Sector Tested by Stakeholder Dynamics in Koudougou (Burkina Faso)

Solid waste management is one of the major concerns of the authorities in the town of Koudougou. The town’s dynamic is reflected in relative demographic growth and consumption patterns that are conducive to the formation of landfill sites. These landfills are the source of numerous environmental consequences and risk factors for local residents. The aim of this article is to analyze the dysfunctions in the solid waste sector caused by the interplay of actors. It draws on secondary data from the state of the art on the subject and primary data collected from 305 households and 89 actors in the sector between September 2022 and March 2023, as part of an ongoing thesis. These data show that the interplay of actors contributes to the malfunctioning of pre-collection and secondary collection, and remains a factor in the proliferation of illegal dumpsites.