Comparison of Headspace Solid-Phase Microextraction with Simultaneous Steam Distillation Extraction for the Analysis of the Volatile Constituents in Chinese Apricot

Volatile constituents in fully mature fruits of apricot （Prunus armeniaca L.） cultivar Xinshiji were extracted using headspace solid-phase microextraction （HS-SPME） and simultaneous steam distillation extraction （SSDE） and then analyzed using capillary gas chromatography and gas chromatography-mass spectrometry. A total of 70 components were identified by HSSPME, including 20 esters, 19 hydrocarbons, 5 alcohols, 5 ketones, 4 acids, 4 lactones, 3 aldehydes, and 10 miscellaneous components, with the esters being the dominant constituent. On the basis of the odor unit values, it is believed that the following compounds probably contributed to the fresh apricot odor： hexyl acetate, β-ionone, butyl acetate, （E）-2-hexenal, linalool, limonene, γ-decalactone, and hexanal. A total of 49 components were also detected by SSDE, including 13 hydrocarbons, 9 alcohols, 7 aldehydes, 9 esters, 4 ketones, 4 lactones, 2 acids, and 1 miscellaneous component, of which the monoterpene alcohols were the dominant constituents. It could be judged from the odor unit values that the following compounds were the major contributors to boiled apricot aroma： β-ionone, linalool, hexyl acetate, γ-dodecalactone, γ- decalactone, （E）-2-hexenal, hexanal, γ-octalactone, phenylacetaldehyde, butyl acetate, limonene, α-terpineol, and δ-decalactone. The results show that HS-SPME is a simple, rapid, and solvent-free method, which is an alternative to the classical SSDE.

Uncertainty Evaluation of Determination of Microcystin MC-LR in Environmental Samples by Solid Phase Extraction-Ultra Performance Liquid Chromatography-Tandem Mass Spectrometry

To assess uncertainty of determination of MC-LR in environmental samples by solid phase extraction- ultra performance liquid chromatography- tandem mass spectrometry,the sources of the uncertainty were evaluated firstly,and the expanded uncertainty was calculated finally.The results show that when MC-LR concentration in the water samples was 0.50 μg/L,the expanded uncertainty was 0.00628 μg/L(k=2).

Determination of Eleutheroside B and E in Acanthopanax Preparations by High-P erformance Liquid Chromatography with Solid-Phase Extraction

Aim An HPLC method for analyzing eleutheroside B (ELU B) and eleutheroside E(ELU E) , two of the main active substances of Acanthopanax preparations were studied. Methods Thesamples were analyzed on a kromasil ODS column with water-acetonitrile as a gradient mobile phase.The flow rate was 0.8 mL·min^(-1) and detecting wavelengths were 206 nm for ELU B, 220 nm for ELUE, solid phase extraction (SPE) and internal standard-salicin were selected. Results The recoveriesof Acanthopanax tablets and injection were 90.4% - 96.8% and 96.4% - 99.8% for ELU B, 87.7% -93.3%and 95.7% - 98.5% for ELU E, respectively. The linear ranges were 4.45 - 22.25 μg· mL^(-1) (r =0.999 8) and 5.11 - 25.55 μg·mL^(-1) ( r = 0.999 7) respectively. Conclusion This method can savethe time for cleaning the chromatographic system and improve sensitivity for Acanthopanaxpreparations , thus providing a way to evaluate the quality of Acanthopanax preparations.

Determination of Triclocarban, Triclosan and Methyl-Triclosan in Environmental Water by Silicon Dioxide/Polystyrene Composite Microspheres Solid-Phase Extraction Combined with HPLC-ESI-MS

This paper developed a sensitive and efficient analytical method for triclocarban (TCC), triclosan (TCS) and Methyl-triclosan (MTCS) determination in environmental water, which involves enrichment by using silicon dioxide/polystyrene composite microspheres solid-phase extraction and detection with HPLC-ESI-MS. The influence of several operational parameters, including the eluant and its volume, the flow rate and acidity of water sample were investigated and optimized. Under the optimum conditions, the limits of detection were 1.0 ng/L, 2.5 and 4.5 ng/L for TCC, TCS, and MTCS, respectively. The linearity of the method was observed in the range of 5-2000 ng/L, with correlation coefficients (r2) >.99. The spiked recoveries of TCC, TCS and MTCS in water sampleswereachieved in the range of 89.5% -96.8% with RSD below 5.7%. The proposed method has been successfully applied to analyze real water samples and satisfactory results were achieved.

Determination of Melamine in Fresh Milk by Electrochemistry with Solid Phase Microextraction at Bismuthyl Chloride Modified Graphite Epoxy Composite Electrode

Melamine as an important chemical raw material and a harmful additive in foods has attracted many people’s attention. In the present paper, The graphite-epoxy composited solid phase electrode was modified with bismuth layer by cyclic voltammetric deposition of bismuth from Bi(NO3)3 aqueous solution including 0.10 M HNO3, and hydrolyzed into micro bismuthyl chloride on-sites. Melamine in fresh milk was extracted with solid phase micro-extraction on the bismuthyl chloride modified graphite-epoxy composited solid electrode. The adsorption of melamine on bismuthyl chloride particle surfaces follows a Freundlich adsorption model, and results in the decrease of the reduction peak current of bismuth in bismuthyl chloride, and determined by differential pulse voltammetry from fresh milk in a larger concentration range of 10–4 ? 10–12 M with detection limit of 2.5 ? 10–12 M and relative standard deviation of 2.7%. The method is sensitive, convenient and was applied in the detection of melamine in fresh milk with relative deviation of 4.2% in content of 0.45 mg/kg melamine in the fresh milk.

Determination of Fe, Cu, and Zn in Water Samples by Microcolumn Packed with Multiwalled Carbon Nanotubes as a Solid Phase Extraction Adsorbent Using ICP-MS

The heavy metals determination in tap water samples using microcolumn packed with multiwalled carbon nanotubes （MWNTs） as a solid-phase extraction adsorbent before to their determination by inductively coupled plasma mass spectrometry （ICP-MS） has been studied. Standard addition method was applied for the calibration using aqueous solutions. The metals ions absorption were achieved by multiwalled carbon nanotubes （MWNTs） at pH 8.0, and then these retained metals on MWNTs column were eluted by 1.0 mol.L^-1 HNO3. The analytical parameters for the determination ofFe, Cu, and Zn in tap water samples which have been investigated previously were applied. Fifteen tap water samples were collected from different locations of Riyadh metropolitan area and then determined the concentration ofFe, Cu, and Zn by ICP-MS after preconcentration with MWNTs. The concentration range for Fe, Cu, and Zn measured （μg/L） in water samples are 23.37-137.91, 2.12-121.36, and 14.43-202.47 respectively. The level of Fe exceeded the limits set by WHO and SASO for drinking water.

Molecularly Imprinted Micro-Solid-Phase Extraction for the Selective Determination of Phenolic Compounds in Environmental Water Samples with High Performance Liquid Chromatraphy

2,4,6-trichlorophenol molecularly imprinted suspension polymer has been prepared and applied to the molecularly imprinted micro-solid-phase extraction procedure for selective preconcentration of phenolic compounds from environmental water samples. The influence of functional monomer, cross-linker, polymerization condition, porogen, and the ratio of template molecule and functional monomer to cross-linker on the size of the obtained particles were investigated. It was found that methyacrylic acid as functional monomer, divinylbenzene as cross-linker, the molar ratio of template molecule and functional monomer to cross-linker was 1:4:20, the amount of AIBN was 100 mg, ultraviolet radiation at 365 nm were the optimal conditions, and at these conditions, the polymers had the best adsorption efficiency and had the monodispersity of 2 - 3 μm microsphere particles. The characteristics of the MIMSPE method were valid by high performance liquid chromatography. This MIMSPE-HPLC method has been successfully applied to the direct preconcentration and determination of phenolic compounds (phenol, 4-chlorophenol, 2,4-dichlorophenol, 2,4,6-trichlorophenol, pentachlorophenol) in environmental water samples.

Development of Extraction and Detection Method for a Chemotherapeutic Drug with Phenytoin in Biological Samples

Dexamethasone is classified as a corticosteroid and is commonly used among cancer patients to decrease the amount of swelling around the tumor. Among patients with cancer, in particular brain tumors, seizures can become a daily routine in their everyday lives. To counteract the seizures, an antiepileptic drug such as phenytoin is administered to act as an anticonvulsant. Phenytoin and dexamethasone are frequently administrated concurrently to brain cancer patients. A previous study has shown that phenytoin serum concentration decreases when administrated concurrently with dexamethasone. Thus, it is important to monitor the concentration of these two drugs in biological samples to ensure that the proper dosages are administrated to the patients. This study aims to develop an effective extraction and detection method for dexamethasone and phenytoin. A reverse-phase high-performance liquid chromatography (HPLC) method with UV/Vis detection has been developed to separate phenytoin and dexamethasone at 219 nm and 241 nm respectively from urine samples. The mobile phase consists of a mixture of 0.01 M KH2PO4, acetonitrile, and methanol adjusted to pH 5.6 (48:32:20) and is pumped at a flow rate of 1.0 mL/min. Calibration curves were prepared for phenytoin and dexamethasone (r2 > 0.99). An efficient solid-phase extraction (SPE) method for the extraction of dexamethasone and phenytoin from urine samples was developed with the use of C-18 cartridges. The percent recovery for phenytoin and dexamethasone is 95.4% (RSD = 1.15%) and 81.1% (RSD = 3.56%) respectively.

Synthesis and Solid Phase Extraction Performance Study of NNAL-specific Molecularly Imprinted Polymers Using Dummy Templates

Dummy molecularly imprinted polymers （DMIPs） for 4-（methylnitrosamino）-1-（3-pyridyl）-1-butanol （NNAL） were produced using three structural analogues as dummy template molecules. The chosen analogues were 4-（acetymethylamino）-1-（3-pyridyl）-butanol, 4- （methylamino）-1-（3-pyridyl）-1-butanol, and 1-（3-pyridyl）-1,4,-butanediol. The molecular recognition characteristics of the produced polymers were evaluated by X-ray photoelec- tron spectroscopy （XPS） and Fourier transform infrared spectroscopy （FT-IR）. Interactions between NNAL and methacrylic acid should be cooperative hydrogen bonds while the ni- trogen atom of the pyridine ring and the oxygen atom of the nitroso group in NNAL are two of the hydrogen-bond acceptors. It was further demonstrated that DMIP synthesized by 4-（acetymethylamino）-1-（3-pyridyl）-butanol had the best binding performance by XPS and FT-IR. Then dummy molecularly imprinted solid phase extraction （DMISPE） was developed for the determination of the analyte using the hit polymer as the sorbing material. Under optimal conditions, the recovery of NNAL dissolved in standard solution reached 93%. And the investigated polymer exhibited much higher binding of NNAL when nicotine was acted as the competitive molecule. Also the proposed method was applied to the measurement of NNAL spiked in blank urine samples with recoveries ranging from 87.2% to 101.2%.

Determination of resveratrol in red wine by solid phase extraction-flow injection chemiluminescence method

A sensitive flow injection chemiluminescence method has been developed for the detection of resveratrol in red wine based on the fact that resveratrol can greatly enhance chemiluminescence reaction between KMnO4 and HCHO in sulfuric acid medium. Analytes were pre-concentrated on solid sorbents （C18 solid-phase extraction cartridges）. Under the optimum conditions, the proposed method allows the measurement of resveratrol over the range of 1.32 × 10^-8 to 1.32 × 10^-5 mol/L with a detection limit of 3.30 ×10^-9 mol/L, and the relative standard deviation for 1.32 ×10^-5 mol/L resveratrol （n = 11） is 3.8%. This method has been successfully applied for the determination of the resveratrol in red wine. Furthermore, the possible reaction mechanism was also discussed.

Influences of solid particles on the formation of the third phase crud during solvent extraction

The influences of solid particles in leach solution on the formation of the third phase crud during solvent extraction of copper were studied. Analyzed from the point of view of pH value and surface tension, the study results showed that the solid particle is one of the most important contributors for the formation of the third phase crud. During solvent extraction, if the pH value was greater than 2.30, the number of solid particles in the mother solution increased, in which case the possibility of forming the third phase crud could also increase, and the interface tension value might grow in pace with the quantity of the third phase crud.

Solid Phase Extraction Chemiluminescence Determination of Methamidaphos on Vegetables

The determination of the methamidaphos pesticide residue on vegetables with a simple solid phase extract（SPE） flow injection（FI） -chemiluminescence（CL） method is described. The method is based on the enhancing effect of methamidaphos on the CL reaction of luminol with hydrogen peroxide in an alkaline solution. Under the optimal conditions, the CL intensity is linear to the methamidaphos mass concentration in a range of 0. 2-13μg/mL （ r= 0. 9992）. The detection limit（3σ） is 0. 047μg/mL. The relative standard deviations for the analysis of three samples are 1.8%, 2.5% and 3.7% （ n = 5 ）, respectively. The recovery is in a range of 90%-109% by the method. In this work, this method was successfully applied to the determination of the methamidaphos residue on some vegetable samples.

A novel surface molecularly imprinted polymer as the solid-phase extraction adsorbent for the selective determination of ampicillin sodium in milk and blood samples

Surface molecularly imprinted polymers （SMIPs） for selective adsorption of ampicillin sodium were synthesized using surface molecular imprinting technique with silica gel as a support. The physical and morphological characteristics of the polymers were investigated by scanning electron microscope （SEM）, Fourier transform infrared spectroscopy （FT-IR）, thermogravimetric analysis （TGA）, elemental analysis and nitrogen adsorption-desorption test. The obtained results showed that the SMIPs displayed great adsorption capacity （13.5 lag/mg）, high recognition ability （the imprinted factor is 3.2） and good binding kinetics for ampicillin sodium. Finally, as solid phase extraction adsorbents, the SMIPs coupled with HPLC method were validated and applied for the enrichment, purification and determination of anapicillin sodium in real milk and blood samples. The averages of spiked accuracy ranged from 92.1% to 107.6%. The relative standard deviations of intra- and inter-day precisions were less than 4.6%. This study provides a new and promising method for enriching, extracting and determining ampicillin sodium in complex biological samples.

Determination of volatile organic compounds in river water by solid phase extraction and gas chromatography

A simple, rapid, and reproducible method is described employing solid phase extraction(SPE) using dichloromethane followed by gas chromatography(GC) with flame ionization detection(FID) for determination of volatile organic compound(VOC) from the Buriganga River water of Bangladesh. The method was applied to detect the benzene, toluene, ethylbenzene, xylene and cumene(BTEXC) in the sample collected from the surface or 15 cm depth of water. Two hundred ml of n hexane pretreated and filtered water samples were applied directly to a C 18 SPE column. BTEXC were extracted with dichloromethane and average concentrations were obtained as 0 104 to 0 372 μg/ml. The highest concentration of benzene was found as 0 372 μg/ml with a relative standard deviation(RSD) of 6 2%, and cumene was not detected. Factors influencing SPE e.g., adsorbent types, sample load volume, eluting solvent, headspace and temperatures, were investigated. A cartridge containing a C 18 adsorbent and using dichloromethane gave better performance for extraction of BTEXC from water. Average recoveries exceeding 90% could be achieved for cumene at 4℃ with a 2 7% RSD.

Development trend and prospect of solid phase extraction technology

Solid phase extraction is widely used in sample pretreatment,concentration and analysis processes due to high selectivity and suitability for low concentration sample system.In this review,we systematically summarized and discussed the development trends of solid phase extraction by bibliometrics method.By analyzing papers output scale,the research and development direction of solid phase extraction technology is prospected.We also give an overview on current strategies of novel solid phase extraction from the separation medium and separation technology.The paper aims to describe the global research profile and the development trends of solid phase extraction,to help researchers to accurately grasp the research trend and to provide support for scientific research institutions to formulate scientific policies and strategic plans.Furthermore,the prospect of the development and application of solid phase extraction is also discussed.

Rapid analysis of fifteen sulfonamide residues in pork and fish samples by automated on-line solid phase extraction coupled to liquid chromatography–tandem mass spectrometry

The aim of this work was to develop an automated on-line solid phase extraction(SPE)with liquid chromatography-tandem mass spectrometry method for the detection of fifteen sulfonamides in pork and fish samples.Samples were extracted with 0.2%formic acid acetonitrile solution,purified by on-line SPE device with HLB column,then separated by XBridge C18 column,using 0.1%formic acid solution and acetonitrile as the mobile phase.Mass spectrometric data was acquired under multiple reaction monitoring(MRM)mode using positive ionization electrospray.Internal standard method was used in the quantification,good linear relationship was got in range of 0.1–100 ng/mL and correlation coefficient was higher than 0.9990.The limits of detection were in the range of 0.125–2.00g/kg and the limits of quantitation were in the range of 0.250–5.00g/kg.Recoveries of the method were in range of 78.3%–99.3%,relative standard deviation were lower than 10%.The method was simple,sensitivity,and could be used for routine supervision and analysis of fifteen sulfonamides in pork and fish.

Preconcentration of copper with multi-walled carbon nanotubes pretreated by potassium permanganate cartridge for solid phase extraction prior to flame atomic absorption spectrometry

A procedure for the preconcentration of copper was described in this paper using multi-walled carbon nanotubes (MWCNTs) oxidized by potassium permanganate as the adsorbent for the enrichment of trace copper in water samples. Important parameters, such as the sample pH, the concentration and volume of eluent, sample flow rate and volume, and interference of coexisting ions, were investigated. The obtained results indicated that proposed method possessed an excellent analytical performance. The linear range, the detection limit, and precison (RSD) were 1–100 ng/mL (R(2) = 0.9993), 0.32 ng/mL and 2.88%, respectively. The results showed that copper could be adsorbed quantitatively on the pretreated MWCNTs with potassium permanganate, and proposed method was very useful in the monitoring of copper in the environment.

Determination of Sulfadimidine in Royal Jelly by C_(18)-functionalized Magnetic Silica Nanoparticles Solid Phase Extraction-High Performance Liquid Chromatography-Tandem Mass Spectrometry

[Objective] This study aimed to develop a method of C_18-functionalized magnetic silica nanoparticles solid phase extraction-high performance liquid chro- matography-tandem mass spectrometry for the determination of sulfadimidine in royal jelly. [Method] The royal jelly samples were pretreated by MCX SPE column and C_18-functionalized magnetic silica nanoparticles, and the purified samples were de- tected by HPLC-MS/MS. [Result] The detection method showed a good linear rela- tionship in the range of 5-80 ugkg （r=0.993 1）. The recovery ranges were between 93%- 104% with the relative standard deviations （RSD） below 11.3%. [Conclusion] Combined with automation equipment, the method is simple, fast, time-saving, and easy to real- ize the automation of sulfadimidine in the royal jelly samples before determination.

Simultaneous Determination of Bisphenols and Alkylphenols in Water by Solid Phase Extraction and Ultra Performance Liquid Chromatography-tandem Mass Spectrometry

To establish an analytical method for determination of four bisphenols （BPA, BPB, BPF, and BPS） and two alkylphenols （4-n-OP, 4-n-NP） in water by ultra performance liquid chromatography- tandem mass spectrometry （UPLC/MS/MS）. The water samples were extracted and condensed with solid-phase extraction （SPE） using C18 cartridges and eluted by acetonitrile. Separation was carried out with Acquity BEH C8 column and detection were performed by UPLC/MS/MS. Quantification was calculated by using the internal standard BPA-d16 and 4-n-NP-d8. The linear correlation coefficients of these compounds in the range of 1.0-100.0μg/L were all over 0.999. The minimum detectable concentrations were 0.75-1.0 ng/L, and the recoveries ranged from 87.0% to 106.9%.

Degradation Dynamics and Residue Analysis of Flubendiamide in Cabbage and Soil by Liquid Chromatography-Tandem Mass Spectrometry with Dispersive Solid Phase Extraction

To formulate a scientific basis for a reasonable spray dose and safe interval period of 20% flubendiamide water dispersible granule (WDG) on controlling vegetable pests, degradation dynamics of flubendiamide in cabbage and soil was analyzed in this study. Dissipation and residue of flubendiamide in 20% flubendiamide WDG in cabbage and soil under field conditions were investigated by liquid chromatography-tandem mass spectrometry with dispersive solid phase extraction. Results showed that the degradation dynamic equations of flubendiamide in cabbage and soil were based on the first-order reaction dynamic equations. The half-lives of the degradation of flubendiamide were 3.51 d to 3.96 d and 3.43 d to 3.87 d in the cabbage of Yangzhou and Jingzhou, respectively, and 4.42 d to 5.13 d and 4.37 d to 4.99 d in the soil of Yangzhou and Jingzhou, respectively. The terminal residues of flubendiamide in the cabbage of Yangzhou and Jingzhou were 0.0247 mg·kg-1 to 0.0393 mg·kg-1 and 0.0225 mg·kg-1 to 0.0273 mg·kg-1, respectively, when 20% flubendiamide WDG was applied at a dose of0.050g·m-2. Flubendiamide is safe to be applied in cabbage fields at the recommended dose.