Strontium ferrite powders prepared from oily cold rolling mill sludge by solid-state reaction method

Oily cold rolling mill （CRM） sludge is one of the pollutants emitted by iron and steel plants. Recycling oily CRM sludge can not only reduce pollution but also bring social and environmental benefits. In this study, using oily CRM sludge as sources of iron oxide, the strontium ferrite powders were synthesized in multiple steps including vacuum distillation, magnetic separation, oxidizing roasting, and solidstate reaction. The optimal technological conditions of vacuum distillation and oxidizing roasting were studied carefully. To consider the effects of Fe203/ SrCO3 tool ratio, calcination temperature, milling time and calcination time on magnetic properties of prepared strontium ferrite powders, the orthogonal experimental method was adopted. The maximum saturation magneti- zation （62.6 mA-m2.g-1） of the synthesized strontium ferrite powders was achieved at the Fe203/SrCO3 mol ratio of 6, 5 h milling time, 1250 ~C calcination temperature, and 1 h calcination time. Strontium ferrite powders syn- thesis method not only provides a cheap, high quality raw material for the production of strontium ferrite powders, but also effectively prevents the environmental pollution.

Study of the (Ca_1–xSr_x) RuO₃System with Nano-Crystals Prepared by the Solid-State Reaction Method

We present a study of their structure, morphology, electrical and magnetic properties on the (Ca1–xSrx) RuO3 system for x = 0.0, 0.07, 0.10, 0.15 and 1.0. The samples were prepared by the solidstate reaction method in air at ambient pressure and heat in the 700℃ - 800℃ range for 48 h. By X-ray powder diffraction (XRD), we determine a solid solution until x = 0.15. Scanning electron microscopy (SEM) indicates that the particle size is 77 - 266 nm. The resistance measurements, as a function of temperature measurements from 7 to 300 K the (Ca1–xSrx) RuO3 system for x = 0.0, 0.07, 0.10, 0.15 and 1.0 show a metallic behaviour. We can even observe that the resistance of the samples is due to the partial substitution of Sr2+ ions and Ru ion valence. Finally, the sample x = 0.07 has a magnetization applied high field to 10 K, whereas that to 300 K does not have a magnetization.

Comparison of the interface reaction behaviors of CaO–V_(2)O_(5) and MnO_(2)–V_(2)O_(5) solid-state systems based on the diffusion couple method

The formation mechanism of calcium vanadate and manganese vanadate and the difference between calcium and manganese in the reaction with vanadium are basic issues in the calcification roasting and manganese roasting process with vanadium slag.In this work,CaO–V_(2)O_(5) and MnO_(2)–V_(2)O_(5) diffusion couples were prepared and roasted for different time periods to illustrate and compare the diffusion reaction mechanisms.Then,the changes in the diffusion product and diffusion coefficient were investigated and calculated based on scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDS) analysis.Results show that with the extension of the roasting time,the diffusion reaction gradually proceeds among the CaO–V_(2)O_(5) and MnO_(2)–V_(2)O_(5) diffusion couples.The regional boundaries of calcium and vanadium are easily identifiable for the CaO–V_(2)O_(5) diffusion couple.Meanwhile,for the MnO_(2)–V_(2)O_(5) diffusion couple,MnO_(2) gradually decomposes to form Mn_(2)O_(3),and vanadium diffuses into the interior of Mn_(2)O_(3).Only a part of vanadium combines with manganese to form the diffusion production layer.CaV_(2)O_(6) and MnV_(2)O_(6) are the interfacial reaction products of the CaO–V_(2)O_(5) and MnO_(2)–V_(2)O_(5) diffusion couples,respectively,whose thicknesses are 39.85 and 32.13μm when roasted for 16 h.After 16 h,both diffusion couples reach the reaction equilibrium due to the limitation of diffusion.The diffusion coefficient of the CaO–V_(2)O_(5) diffusion couple is higher than that of the MnO_(2)–V_(2)O_(5) diffusion couple for the same roasting time,and the diffusion reaction between vanadium and calcium is easier than that between vanadium and manganese.

Exponential Time Differencing Method for a Reaction-Diffusion System with Free Boundary

For reaction-diffusion equations in irregular domains with moving boundaries,the numerical stability constraints from the reaction and diffusion terms often require very restricted time step sizes,while complex geometries may lead to difficulties in the accuracy when discretizing the high-order derivatives on grid points near the boundary.It is very challenging to design numerical methods that can efficiently and accurately handle both difficulties.Applying an implicit scheme may be able to remove the stability constraints on the time step,however,it usually requires solving a large global system of nonlinear equations for each time step,and the computational cost could be significant.Integration factor(IF)or exponential time differencing(ETD)methods are one of the popular methods for temporal partial differential equations(PDEs)among many other methods.In our paper,we couple ETD methods with an embedded boundary method to solve a system of reaction-diffusion equations with complex geometries.In particular,we rewrite all ETD schemes into a linear combination of specificФ-functions and apply one state-of-the-art algorithm to compute the matrix-vector multiplications,which offers significant computational advantages with adaptive Krylov subspaces.In addition,we extend this method by incorporating the level set method to solve the free boundary problem.The accuracy,stability,and efficiency of the developed method are demonstrated by numerical examples.

A review of ^(17)O isotopic labeling techniques for solid-state NMR structural studies of metal oxides in lithium-ion batteries

Recent advances in utilizing ^(17)O isotopic labeling methods for solid-state nuclear magnetic resonance(NMR)investigations of metal oxides for lithium-ion batteries have yielded extensive insights into their structural and dynamic details.Herein,we commence with a brief introduction to recent research on lithium-ion battery oxide materials studied using ^(17)O solid-state NMR spectroscopy.Then we delve into a review of ^(17)O isotopic labeling methods for tagging oxygen sites in both the bulk and surfaces of metal oxides.At last,the unresolved problems and the future research directions for advancing the ^(17)O labeling technique are discussed.

Synthesis of Copper Oxalate Nanorods by a Simple One-step Solid-state Chemical Reaction Method

Copper oxalate nanorods were successfully prepared by means of a simple one-step solid-state reaction method with the assistance of a suitable surfactant, polyethylene glycol 400. The product with uniform rod-like morphology was characterized by XRD, TEM and SEM. The formational mechanism of the rod-like structure was also preliminary discussed.

Preparation of nano-sized cerium and titanium pyrophosphates via solid-state reaction at room temperature

Nano-sized cerium-titanium pyrophosphates Ce1-xTixP2O7 （with x = 0, 0.2, 0.5, 0.7, 0.9, and 1.0） were obtained by grinding a mixture of Ce（SO4）2·4H2O, Ti（SO4）2, and Na4P2O7·10H2O in the presence of surfactant PEG-400 at room temperature, washing the mixture with water to remove soluble inorganic salts, and drying at 100℃. The products and their calcined samples were characterized using ultraviolet-visible spectroscopy （UV-vis）, thermogravimetry and differential thermal analyses （TG/DTA）, X-ray powder diffraction （XRD）, and transmission electron microscopy （TEM）. The results show that nano-sized Ce1-xTixP2O7 behave as an excellent UV-shielding material. Thereinto, the CeP2O7 has the most excellent UV-shielding effect, and the amorphous state of Ce0.8Ti0.2P2O7 can keep at a higher temperature than CeP2O7. Therefore, the stabilization of the amorphous state of the cerium pyrophosphates was carded out by doping titanium. This stabilization is a significant improvement, which enables to apply these amorphous pyrophosphates not only to cosmetics and paints, but also plastics and films.

Electrochemical properties of spinel LiMn_2O_4 and LiAl_(0.1)Mn_(1.9)O_(3.9)F_(0.1) synthesized by solid-state reaction

Two types of spinel cathode powders, LiMn2O4 and LiAl0.1Mn1.9O3.9F0.1, were synthesized by solid-state reaction, X-ray diffraction （XRD） patterns of the prepared samples were identified as the spinel structure with a space group of Fd 3^- m. The cubic lattice parameter was determined from least-squares fitting of the XRD data. The LiAl0.1Mn1.9O3.9F0.1 sample showed a little lower initial capacity, but better cycling performance than the LiMn2O4 sample at both room temperature and an elevated temperature. The Vanderbilt method was used to test the electrochemical conductivity of the LiMn2O4 samples. The electrochemical impedance spectroscopy （EIS） method was employed to investigate the electrochemical properties of these spinel LiMn2O4 samples.

Kinetics of solid-state reduction of chromite overburden

The demand for alternative low-grade iron ores is on the rise due to the rapid depletion of high-grade natural iron ore resources and the increased need for steel usage in daily life.However,the use of low-grade iron ores is a constant clinical task for industry metallurgists.Direct smelting of low-grade ores consumes a substantial amount of energy due to the large volume of slag generated.This condition can be avoided by direct reduction followed by magnetic separation(to separate the high amount of gangue or refractory and metal parts)and smelting.Chromite overburden(COB)is a mine waste generated in chromite ore processing,and it mainly consists of iron,chromium,and nickel(<1wt%).In the present work,the isothermal and non-isothermal kinetics of the solid-state reduction of self-reduced pellets prepared using low-grade iron ore(COB)were thoroughly investigated via thermal analysis.The results showed that the reduction of pellets followed a firstorder autocatalytic reaction control mechanism in the temperature range of 900-1100℃.The autocatalytic nature of the reduction reaction was due to the presence of nickel in the COB.The apparent activation energy obtained from the kinetics results showed that the solid-state reactions between COB and carbon were the rate-determining step in iron oxide reduction.

Application-oriented hydrolysis reaction system of solid-state hydrogen storage materials for high energy density target:A review

Hydrogen storage and delivery technology is still a bottleneck in the hydrogen industry chain.Among all kinds of hydrogen storage methods,light-weight solid-state hydrogen storage(LSHS)materials could become promising due to its intrinsic high hydrogen capacity.Hydrolysis reaction of LSHS materials occurs at moderate conditions,indicating the potential for portable applications.At present,most of review work focuses on the improvement of material performance,especially the catalysts design.This part is important,but the others,such as operation modes,are also vital to to make full use of material potential in the practical applications.Different operation modes of hydrolysis reaction have an impact on hydrogen capacity to various degrees.For example,hydrolysis in solution would decrease the hydrogen capacity of hydrogen generator to a low value due to the excessive water participating in the reaction.Therefore,application-oriented operation modes could become a key problem for hydrolysis reaction of LSHS materials.In this paper,the operation modes of hydrolysis reaction and their practical applications are mainly reviewed.The implements of each operation mode are discussed and compared in detail to determine the suitable one for practical applications with the requirement of high energy density.The current challenges and future directions are also discussed.

Recent advance in high-pressure solid-state metathesis reactions

High-pressure solid-state metathesis(HPSSM)reaction is an effective route to novel metal nitrides.A recent advance in HPSSM reactions is presented for a number of examples,including 3d transition metal nitrides(ε-Fe_(3)N,ε-Fe_(3-x)Co_(x)N,CrN,and Co_(4)N_(x)),4d transition metal nitrides(MoNx),and 5d transition metal nitrides(Re_(3)N,WN_(x)).Thermodynamic investigations based on density functional theory(DFT)calculations on several typical HPSSM reactions between metal oxides and boron nitride indicate that the pressure could reduce the reaction enthalpy △H.High-pressure confining environment thermodynamically favors an ion-exchange process between metal atom and boron atom,and successfully results in the formation of well-crystalized metal nitrides with potential applications.

Robust interface layers with redox shuttle reactions suppress the dendrite growth for stable solid-state Li metal batteries

Designing a durable lithium metal anode for solid state batteries requires a controllable and uniform deposition of lithium, and the metal lithium layer should maintain a good interface contact with solid state electrolyte during cycles. In this work, we construct a robust functional interface layer on the modified LiB electrode which considerably improves the electrochemical stability of lithium metal electrode in solid state batteries. It is found that the functional interface layer consisting of polydioxolane, polyiodide ion and Li TFSI effectively restrains the growth of lithium dendrites through the redox shuttle reaction of I-/I3-and maintains a good contact between lithium anode and solid electrolyte during cycles. Benefit from these two advantages, the modified Li-B anode exhibits a remarkable cyclic performance in comparison with those of the bare Li-B anode.

Synthesis strategies of covalent organic frameworks: An overview from nonconventional heating methods and reaction media

Covalent organic frameworks(COFs), as an emerging class of porous crystalline materials constructed by covalent links between the building monomers, have gained tremendous attention. Over the past 15 years, COFs have made rapid progress and substantial development in the chemistry and materials fields. However, the synthesis of COFs has been dominated by solvothermal methods for a long time and it usually involves high temperature, high pressure and toxic organic solvents, which created many challenges for environmental considerations. Recently,the exploration of new approaches for facile fabrication of COFs has aroused extensive interest. Hence, in this review, we comprehensively describe the synthetic strategies of COFs from the aspects of nonconventional heating methods and reaction media. In addition, the advantages,limitations and properties of the preparation methods are compared. Finally, we outline the main challenges and development prospects of the synthesis of COFs in the future and propose some possible solutions.

Effects of Solid-State Reaction Synthesis Processing Parameters on Thermoelectric Properties of Mg_2Si

The Mg_(2)Si-matrix thermoelectric material was synthesized by low temperature solid-state reaction.This paper studies the effects of holding time and reaction temperature on the particle size and the properties of the material,and also studies effects of doping elemental Sb,Te and their doping seqence on the properties of the material.The result shows that excessively high temperature and elongated holding time of solid-state reaction are harmful,there is a range of particle size to ensure optimum properties and the doping sequence of Sb or Te without influencing the properties.

Synthesis and characterization of high-voltage cathode material LiNi0.5Mn1.5O4 by one-step solid-state reaction

LiNi0. 5 Mn1. 5 O4 was prepared under various conditions by one-step solid-state reaction in air and its properties were investigated by X-ray diffractormetry (XRD), scanning electron microscopy (SEM) and electrochemical measurement. XRD patterns show that LiNi0. 5 Mn1. 5 O4 synthesized under various conditions has cubic spinel structure. SEM images exhibit that the particle size increases with increasing calcination temperature and time. Electro chemical test shows that the LiNi0. 5 Mn1.5 O4 calcined at 700 ℃ for 24 h delivers up to 143 mA · h/g, and the capacity retains 132 mA · h/g after 30 cycles.

Preparation of NH_4ZrH(PO_4)_2·H_2O via solid-state reaction at low heat and its catalytic performance in the synthesis of butyl acetate

Nanocrystalline NH4ZrH（PO4）2·H2O was obtained by grinding ZrOC12·8H2O and （NH4）2HPO4 in the presence of surfactant PEG-400 via solid-state reaction at room temperature. The product NH4ZrH（PO4）2·H2O and its product of thermal decomposition were characterized using thermogravimetry and differential thermal analyses （TG/DTA）, Fourier transform infrared spectroscopy （FT-IR）, X-ray powder diffraction （XRD）, and transmission electron microscopy （TEM）. Nanocrystalline NHaZrH（PO4）2·H2O with an average particle size of 17 nm was obtained when the product was kept at80℃ for 3 h. Its crystalline framework was stable at temperatures below 250℃. In addition, the catalytic performance of NH4ZrH（PO4）2·H2O in the synthesis of butyl acetate was investigated. The results show that NH4ZrH（PO4）2·H2O behaved as an excellent heterogeneous catalyst in the synthesis of butyl acetate.

Solid-state reaction of a CaO−V_(2)O_(5)mixture:A fundamental study for the vanadium extraction process

The aim of this study was to investigate the phase transformation and kinetics of the solid-state reaction of CaO−V_(2)O_(5),which is the predominant binary mixture involved in the vanadium recovery process.Thermal analysis,X-ray diffraction spectroscopy,scanning electron microscopy,and energy dispersive spectrometry were used to characterize the solid-state reaction of the samples.The extent of the solid reac-tion was derived using the preliminary quantitative phase analysis of the X-ray patterns.The results indicate that the solid reaction of the CaO−V_(2)O_(5)mixture is strongly influenced by the reaction temperature and CaO/V_(2)O_(5)mole ratio.The transformation of calcium vanadate in-volves a step-by-step reaction of CaO−V_(2)O_(5),CaO−CaV_(2)O_(6),and CaO−Ca_(2)V_(2)O7 depending on the CaO/V_(2)O_(5)mole ratio.The kinetic data of the solid reaction of the CaO−V_(2)O_(5)(1:1)mixture followed a second-order reaction model.The activation energy(Ea)and preexponential factor(A)were determined to be 145.38 kJ/mol,and 3.67×10^(8)min^(−1),respectively.

Preparation of new sunscreen materials Ce_(1-x)Zn_xO_(2-x) via solid-state reaction at room temperature and study on their properties

Superfine cerium-zinc oxides Ce1-xZnxO2-x with x = 0, 0.1, 0.3, 0.5, and 1.0 were obtained by grinding Ce（SO4）2·4H2O, ZnSO4·7H2O and NH4HCO3 under the condition of surfactant PEG-400 being present at room temperature, washing the mixture with water to remove soluble inorganic salts, drying at 80°C, and calcining.The precursor and its calcined samples were characterized using thermogravimetry and differential thermal analyses（TG/DTA）, UV-vis absorption spectroscopy, X-ray powder diffraction（XRD）, and scanning electron microscopy（SEM）.The results showed that superfine Ce1-xZnxO2-x behaved as an excellent UV-shielding material.The ZnO-doped CeO2 can facilitate the formation of crystalline state CeO2.The catalytic ability of products used in air oxidation of castor oil was investigated.The results showed that the catalytic abilities of products decreased with increasing zinc amount.

Synthesis of Nano-sized Barium Titanate Powder by Solid-state Reaction between Barium Carbonate and Titania

Size control of BaTiO3 in solid-state reaction between BaCO3 and TiO2 was demonstrated by varying the size of TiO2 and milling conditions of BaCO3. The smaller TiO2 particles had higher surface area, resulting in faster initial reaction. The mechanically milled BaCO3 particles accelerated the diffusion process and decreased the calcinations temperature. It can be deduced from the results that the size control is possible and nano-sized BaTiO3 particles with about 60 nm can be synthesized by using the conventional solid-state reaction between BaCO3 and TiO2.

Preparation of Li[Ni_(1/3)Co_(1/3)Mn_(1/3)]O_2 powders for cathode material in secondary battery by solid-state method

Employing Li2CO3, NiO, Co3O4, and MnCO3 powders as starting materials, Li[Ni1/3Co1/3Mn1/3]O2 was synthesized by solid-state reaction method. Various grinding aids were applied during milling in order to optimize the synthesis process. After successive heat treatments at 650 and 950 ℃, the prepared powders were characterized by X-ray diffraction (XRD) analysis, scanning electron microscopy, and transmission electron microscopy. The powders prepared by adding salt (NaCl) as grinding aid exhibit a clear R3m layer structure. The powders by other grinding aids like heptane show some impurity peaks in the XRD pattern. The former powders show a uniform particle size distribution of less than 1 μm average size while the latter shows a wide distribution ranging from 1 to 10 μm. Energy dispersive X-ray (EDX) analysiss show that the ratio of Ni, Co, and Mn content in the powder is approximately 1/3, 1/3, and 1/3, respecively. The EDX data indicate no incorporation of sodium or chlorine into the powders. Charge-discharge tests gave an initial discharge capacity of 160 mAh·g-1 for the powders with NaCl addition while 70 mAh·g-1 for the powders with heptane.