Formative mechanism of preferential solution flow during dump leaching

Preferential flow is a rapid movement of solution through pores caused by coarse ores. Macropore is the main factor for the preferential flow. Macropore can be defined from three aspects. Segregation of the ores during dumping was studied according to particle kinematics. Small ores become smaller under the effect of acid and weathering. Clay in the rainwater from the hillside precipitates in the dump. Segregation and fine ores are the main causes in macropore. The permeability in coarse ores is better than that in fine ores. The mechanism in the preferential flows was studied combining the fast conducting effect of the macropore. Experimental result shows that, at certain application rate, fine ore area is saturated while large volume of solution flows laterally to the coarse ore area and leaks out quickly through the macropores. Thus the mechanism of preferential solution flows is further illustrated.

Experimental study on preferential solution flow during dump leaching of low-grade ores

The phenomenon of preferential solution flow during dump leaching of low-grade ores was studied.The formative mechanism of preferential solution flow was investigated through analyzing the relationship between permeability and ore diameter,and the relationship between surface tension and ore diameter.The preferential solution flow happened within the fine ore area when the dump was unsaturated.And it could happen within the coarse ore area when the dump became saturated.The results of experiment show that the outflow of coarse ore area increases sharply with higher applied rate.The outflow of fine ore area is greater than that of coarse ore area when the applied rate is below 3.2 L/min,and the preferential solution flow happens in fine ore area.But the preferential solution flow happens in coarse ore area when the applied rate is higher than 3.2 L/min.The result of the experiment is consistent with the mechanism analyzing.

Solution flow rate influence on ZnS thin films properties grown by ultrasonic spray for optoelectronic application

The aim of this work is to investigate the dependence of Zn S thin films structural and optical properties with the solution flow rate during the deposition using an ultrasonic spray method. The solution flow rate ranged from 10 to 50 m L/h and the substrate temperature was maintained at 450 °C. The effect of the solution flow rate on the properties of Zn S thin films was investigated by X-ray diffraction（XRD）, scanning electron microscopy（SEM）, optical transmittance spectroscopy（UV–V） and the four-point method. The X-ray diffraction analysis showed that the deposited material was pure zinc sulphide, it has a cubic sphalerite structure with preferential orientation along the（111） direction. The grain size values were calculated and found to be between 38 to 82 nm.SEM analysis revealed that the deposited thin films have good adherence to the substrate surfaces, are homogeneous and have high density. The average transmission of all films is up more than 65% in the range wavelength from 200 to 1100 nm and their band gap energy values were found between 3.5–3.92 e V. The obtained film thickness varies from 390 to 1040 nm. Moreover, the electric resistivity of the deposited films increases with the increasing of the solution flow rate between 3.51 × 10^5 and 11 × 10^5 Ω·cm.

A class of exact solutions for the incompressible viscous magnetohydrodynamic flow over a porous rotating disk

The present paper is concerned with a class of ex- act solutions to the steady Navier-Stokes equations for the incompressible Newtonian viscous electrically conducting fluid flow due to a porous disk rotating with a constant angu- lar speed. The three-dimensional hydromagnetic equations of motion are treated analytically to obtained exact solutions with the inclusion of suction and injection. The well-known thinning/thickening flow field effect of the suction/injection is better understood from the constructed closed form veloc- ity equations. Making use of this solution, analytical formu- las for the angular velocity components as well as for the permeable wall shear stresses are derived. Interaction of the resolved flow field with the surrounding temperature is fur- ther analyzed via the energy equation. The temperature field is shown to accord with the dissipation and the Joule heating. As a result, exact formulas are obtained for the temperature field which take different forms corresponding to the condi- tion of suction or injection imposed on the wall.

Optimal Power Flow Solution Using Particle Swarm Optimization Technique with Global-Local Best Parameters

This paper proposes an efficient method for optimal power flow solution （OPF） using particle swarm optimization （PSO） technique. The objective of the proposed method is to find the steady state operation point in a power system which minimizes the fuel cost, while maintaining an acceptable system performance in terms of limits on generator power, line flow limits and voltage limits. In order to improvise the performance of the conventional PSO （cPSO）, the fine tuning parameters- the inertia weight and acceleration coefficients are formulated in terms of global-local best values of the objective function. These global-local best inertia weight （GLBestlW） and global-local best acceleration coefficient （GLBestAC） are incorporated into PSO in order to compute the optimal power flow solution. The proposed method has been tested on the standard IEEE 30 bus test system to prove its efficacy. The results are compared with those obtained through cPSO. It is observed that the proposed algorithm is computationally faster, in terms of the number of load flows executed and provides better results than the conventional heuristic techniques.

ANALYTICAL SOLUTION OF FLOW IN INFINITE STRATIFIED OIL RESERVOIR AND ITS APPLICATION

This paper presents an analytical solution for the production function and pressure distribution function of flow in infinite stratified oil reservoir with crosflow under the condition of constant wellbore pressure (CWP condition) by Weber's integral transformation. The calculation results are shown in the form of curves and these results can be used to analyse unsteady flow test of production with CWP condition.

AN ANALYTIC SOLUTION ON HYPERSONIC FLOW OVER AN ARBTTRARY SLENDER BODY WITH NEAR POWER-LAW PROFILE

On the basis of a self-similar solution as well as of the assumption of the 'Transserse Motion',a general linear theory on hypersonic flow over a general slender body is set up in this paper By means of this theory, the problem concerned can he put into a universal system of O.D Eqs .which can be integrated manerically in adyance

AN ANALYTIC SOLUTION OF DENSE TWO-PHASE FLOW IN A VERTICAL PIPELINE

According to a mathematical model for dense two-phase flows presented in the previous pape[1],a dense two-phase flow in a vertical pipeline is analytically solved, and the analytic expressions of velocity of each continuous phase and dispersed phase are respectively derived. The results show that when the drag force between twophasesdepends linearly on their relative velocity, the relative velocity profile in the pipeline coincides with Darcy's law except for the thin layer region near the pipeline wall, and that the theoretical assumptions in the dense two-phase flow theory mentioned are reasonable.

ANALYTICAL SOLUTIONS FOR EQUATIONS OF UNSTEADY FLOW OF NON-NEWTONIAN FLUIDS IN TUBE

This paper presents analytieal solutions to the partial differential equations for unsteady flow of the second-order fluid and Maxwell fluid in tube by using the integral transform method. It can be used to analyse the behaviour of axial velocity and shear stress for unsteady flow of nun-Newtonian visco-elastie fluids in tube, and to provide a theoretical base for the projection of pipe-line engineering.

NUMERICAL SOLUTION OF NAVIER-STOKES EQUATION OF UNSTEADY SEPARATED FLOWS DUE TO A SPOILER'S OSCILLATION

The finite difference method (FDM) is applied in the present paper to solve the unsteady NHS equations for incompressible fluids. ADI and SLOR methods are served for the vorticity equation and the Poisson equation for ψ respectively. The upwind scheme is used for the convective terms. The moving boundary conditions are specially treated, and the effects of outlet conditions on the flow field are abo examined. Numerical results obtained show that the spoiler's oscillation induces forming, growing and shedding of the vortices. The shedding frequency of vortices is equal to that of the spoiler's oscillation. The forced unsteady separated flows under the present investigation depend mainly on the reduced frequency. At low reduced frequency, the vortices shed from the spoiler interact weakly with each other, and move downstream at an almost uniform speed of 038 V∞. At high reduced frequency, the interaction between the adjacent vortices strengthens. They close up to and rotate around each other, and eventually, merge into one vortex.

Mathematical model for coupled reactive flow and solute transport during heap bioleaching of copper sulfide

Based on the momentum and mass conservation equations, a comprehensive model of heap bioleaching process is developed to investigate the interaction between chemical reactions, solution flow, gas flow, and solute transport within the leaching system. The governing equations are solved numerically using the COMSOL Multiphysics software for the coupled reactive flow and solute transport at micro-scale, meso-scale and macro-scale levels. At or near the surface of ore particle, the acid concentration is relatively higher than that in the central area, while the concentration gradient decreases after 72 d of leaching. The flow simulation between ore particles by combining X-ray CT technology shows that the highest velocity in narrow pore reaches 0.375 m/s. The air velocity within the dump shows that the velocity near the top and side surface is relatively high, which leads to the high oxygen concentration in that area. The coupled heat transfer and liquid flow process shows that the solution can act as an effective remover from the heap, dropping the highest temperature from 60 to 38 ℃. The reagent transfer coupled with solution flow is also analyzed. The results obtained allow us to obtain a better understanding of the fundamental physical phenomenon of the bioleaching process.

Power Flow Analytical Solutions and Multi-dimensional Voltage Stability Boundaries Based on Multivariate Quotient-difference Method

This paper proposes a novel Multivariate Quotient-Difference(MQD)method to obtain the approximate analytical solution for AC power flow equations.Therefore,in the online environment,the power flow solutions covering different operating conditions can be directly obtained by plugging values into multiple symbolic variables,such that the power injections and consumptions of selected buses or areas can be independently adjusted.This method first derives a power flow solution through a Multivariate Power Series(MPS).Next,the MQD method is applied to transform the obtained MPS to a Multivariate Pad´e Approximants(MPA)to expand the Radius of Convergence(ROC),so that the accuracy of the derived analytical solution can be significantly increased.In addition,the hypersurface of the voltage stability boundary can be identified by an analytical formula obtained from the coefficients of MPA.This direct method for power flow solutions and voltage stability boundaries is fast for many online applications,since such analytical solutions can be derived offline and evaluated online by only plugging values into the symbolic variables according to the actual operating conditions.The proposed method is validated in detail on New England 39-bus and IEEE 118-bus systems with independent load variations in multi-regions.

MHD stagnation-point flow and heat transfer towards stretching sheet with induced magnetic field

The problem of the steady magnetohydrodynamic （MHD） stagnation-point flow of an incompressible viscous fluid over a stretching sheet is studied. The effect of an induced magnetic field is taken into account. The nonlinear partial differential equations are transformed into ordinary differential equations via the similarity transformation. The transformed boundary layer equations are solved numerically using the shooting method. Numerical results are obtained for various magnetic parameters and Prandtl numbers. The effects of the induced magnetic field on the skin friction coefficient, the local Nusselt number, the velocity, and the temperature profiles are presented graphically and discussed in detail.

Response of Lettuce to the Coupling Electrical Conductivity and Circulation Rate of the Nutrient Solution in Hydroponics

The coupling effect of nutrient solution EC （electrical conductivity） levels and CR （circulation rate） on the morphology and quality, in hydroponically grown lettuce was assessed. Lettuce was grown at 5 treatments fi＇om High EC ＆ Low CR to Low EC ＆ High CR. The environmental parameters were controlled in a 20 m^2 plant factory during the hydroponic cultivation with the following values： irradiated by blue and red light-emitting diode lighting with PPFD （photosynthetic photon flux density） value of 150 mol·m^-2·s^-1 for 16 hours per day; Temperature was maintained at 22.0 ℃ during the photoperiod and 16.0 ℃ in dark cycle. The results demonstrate that growing lettuce can be adopted using nutrient solution with lower EC levels and higher CR. The results also indicate that the effect of bi-directional coupled EC and CR resulted in expansion of root length but reducing the root biomass. Nitrate content was significantly reduced.

Numerical modelling of flow and transport in rough fractures

Simulation of flow and transport through rough walled rock fractures is investigated using the latticeBoltzmann method （LBM） and random walk （RW）, respectively. The numerical implementation isdeveloped and validated on general purpose graphic processing units （GPGPUs）. Both the LBM and RWmethod are well suited to parallel implementation on GPGPUs because they require only next-neighbourcommunication and thus can reduce expenses. The LBM model is an order of magnitude faster onGPGPUs than published results for LBM simulations run on modern CPUs. The fluid model is verified forparallel plate flow, backward facing step and single fracture flow; and the RWmodel is verified for pointsourcediffusion, Taylor-Aris dispersion and breakthrough behaviour in a single fracture. Both algorithmsplace limitations on the discrete displacement of fluid or particle transport per time step to minimise thenumerical error that must be considered during implementation. 2014 Institute of Rock and Soil Mechanics, Chinese Academy of Sciences. Production and hosting byElsevier B.V. All rights reserved.

Multiple solutions and stability of the steady transonic small-disturbance equation

Numerical solutions of the steady transonic small-disturbance（TSD） potential equation are computed using the conservative Murman-Cole scheme. Multiple solutions are discovered and mapped out for the Mach number range at zero angle of attack and the angle of attack range at Mach number 0.85 for the NACA 0012 airfoil. We present a linear stability analysis method by directly assembling and evaluating the Jacobian matrix of the nonlinear finite-difference equation of the TSD equation. The stability of all the discovered multiple solutions are then determined by the proposed eigen analysis. The relation of stability to convergence of the iterative method for solving the TSD equation is discussed. Computations and the stability analysis demonstrate the possibility of eliminating the multiple solutions and stabilizing the remaining unique solution by adding a sufficiently long splitter plate downstream the airfoil trailing edge. Finally, instability of the solution of the TSD equation is shown to be closely connected to the onset of transonic buffet by comparing with experimental data.

CAUCHY PROBLEM FOR LINEARIZED SYSTEM OF TWO-DIMENSIONAL ISENTROPIC FLOW WITH AXISYMMETRICAL INITIAL DATA IN GAS DYNAMICS

The explicit solution to Cauchy problem for linearized system of two-dimensional isentropic flow with axisymmetrical initial data in gas dynamics is given.

Fourier time spectral method for subsonic and transonic flows

The time accuracy of the exponentially accurate Fourier time spectral method（TSM） is examined and compared with a conventional 2nd-order backward difference formula（BDF） method for periodic unsteady flows. In particular, detailed error analysis based on numerical computations is performed on the accuracy of resolving the local pressure coefficient and global integrated force coefficients for smooth subsonic and non-smooth transonic flows with moving shock waves on a pitching airfoil. For smooth subsonic flows, the Fourier TSM method offers a significant accuracy advantage over the BDF method for the prediction of both the local pressure coefficient and integrated force coefficients. For transonic flows where the motion of the discontinuous shock wave contributes significant higherorder harmonic contents to the local pressure fluctuations,a sufficient number of modes must be included before the Fourier TSM provides an advantage over the BDF method.The Fourier TSM, however, still offers better accuracy than the BDF method for integrated force coefficients even for transonic flows. A problem of non-symmetric solutions for symmetric periodic flows due to the use of odd numbers of intervals is uncovered and analyzed. A frequency-searching method is proposed for problems where the frequency is not known a priori. The method is tested on the vortex shedding problem of the flow over a circular cylinder.

Numerical study of homogeneous–heterogeneous reactions on stagnation point flow of ferrofluid with non-linear slip condition

This study deals with the stagnation point flow of ferrofluid over a flat plate with non-linear slip boundary condition in the presence of homogeneous-heterogeneous reactions.Three kinds of ferroparticles,namely,magnetite(Fe_3O_4),cobalt ferrite(CoFe_2O_4) and manganese zinc ferrite(Mn-ZnFe_2O_4) are taken into account with water and kerosene as conventional base fluids.The developed model of homogeneous-heterogeneous reactions in boundary layer flow with equal and unequal diffusivities for reactant and autocatalysis is considered.The governing partial differential equations are converted into system of non-linear ordinary differential equations by mean of similarity transformations.These ordinary differential equations are integrated numerically using shooting method.The effects of pertinent parameters on velocity and concentration profiles are presented graphically and discussed.We found that in the presence of Fe_3O_4-kerosene and CoFe_2O_4-kerosene,velocity profiles increase for large values of α and β whereas there is a decrement in concentration profiles with increasing values of if and K_s.Furthermore,the comparison between non-magnetic(A1_2O_3) and magnetic Fe_3O_4 nanoparticles is given in tabular form.

Unsteady Rotative Flow of Non-Newtonian Fluid in an Annular Pipe

This paper .Studies power law no-Newtonian fluid rotative flow. in an annularpipe. The governing equation is nonlinear one, we linearized the governing equationby assuming that partial factor is at state. With Laplace transform we obtain ananalytical solution of the problem In the paper several groups of curves are given.these curves reflect the temporal change law and. spatial distribution of fluid velocity.In addition.we study the effection of power law index on the flow field the resultindicates that when the power law index n < l. the flow velocity is highly sensitive tothe index. and this fact is importanl in related engineering decisions.