A novel approach to conductive EMI noise source modeling

A new approach to conductive electromagnetic interference （EMI） noise source modeling, i. e. the source internal impedance extraction, is presented. First, the impedance magnitude is achieved through an exciting probe and a detecting probe, or through calculations based on insertion loss measurement results when inserting a series nigh-value known impedance or a shunt low-value known impedance in the circuit. Then the impedance phase is extracted by the Hilbert transform （HT） of the logarithm of the obtained impedance magnitude. Performance studies show that the estimated phase error can increase greatly at a zero frequency in the Hilbert transform because of the existence of a singular point, and this effect can be eliminated by introducing a zero-point when the noise source does not include a series-connected capacitive component. It is also found that when the frequency is nigher than 150 kHz, the estimated phase error is not sensitive to the inductive source but sensitive to the capacitive source. Finally, under the conditions of the same measurement accuracies for impedance magnitude, the accuracy of complex impedance based on the HT can be improved about 10 times when compared with the accuracy of estimated parameters based on the impedance magnitude fitting method （IMFM）.

A GIS-based time-dependent seismic source modeling of Northern Iran

： The first step in any seismic hazard study is the definition of seismogenic sources and the estimation of magnitude-frequency relationships for each source. There is as yet no standard methodology for source modeling and many researchers have worked on this topic. This study is an effort to define linear and area seismic sources for Northern Iran. The linear or fault sources are developed based on tectonic features and characteristic earthquakes while the area sources are developed based on spatial distribution of small to moderate earthquakes. Time-dependent recurrence relationships are developed for fault sources using renewal approach while time-independent frequency-magnitude relationships are proposed for area sources based on Poisson process. GIS functionalities are used in this study to introduce and incorporate spatial- temporal and geostatistical indices in delineating area seismic sources. The proposed methodology is used to model seismic sources for an area of about 500 by 400 square kilometers around Tehran. Previous researches and reports are studied to compile an earthquake/fault catalog that is as complete as possible. All events are transformed to uniform magnitude scale; duplicate events and dependent shocks are removed. Completeness and time distribution of the compiled catalog is taken into account. The proposed area and linear seismic sources in conjunction with defined recurrence relationships can be used to develop time-dependent probabilistic seismic hazard analysis of Northern Iran.

Strong motion simulation by the composite source modeling:A case study of 1679 M8.0 Sanhe-Pinggu earthquake

In this study, a composite source model has been used to calculate the realistic strong ground motions in Beijing area, caused by 1679 Ms8.0 earthquake in Sanhe-Pinggu. The results could provide us the useful physical parameters for the future seismic hazard analysis in this area. Considering the regional geological/geophysical background, we simulated the scenario earthquake with an associated ground motions in the area ranging from 39.3°N to 41. 1°N in latitude and from 115.35°E to 117.55°E in longitude. Some of the key factors which could influence the characteristics of strong ground motion have been discussed, and the resultant peak ground acceleration （PGA） distribution and the peak ground velocity （PGV） distribution around Beijing area also have been made as well. A comparison of the simulated result with the results derived from the attenuation relation has been made, and a sufficient discussion about the advantages and disadvantages of composite source model also has been given in this study. The numerical results, such as the PGA, PGV, peak ground displacement （PGD）, and the three-component time-histories developed for Beijing area, have a potential application in earthquake engineering field and building code design, especially for the evaluation of critical constructions, government decision making and the seismic hazard assessment by financial/insurance companies.

Two States CBR Modeling of Data Source in Dynamic Traffic Monitoring Sensor Networks

Real traffic information was analyzed in the statistical characteristics and approximated as a Gaussian time series. A data source model, called two states constant bit rate (TSCBR), was proposed in dynamic traffic monitoring sensor networks. Analysis of autocorrelation of the models shows that the proposed TSCBR model matches with the statistical characteristics of real data source closely. To further verify the validity of the TSCBR data source model, the performance metrics of power consumption and network lifetime was studied in the evaluation of sensor media access control (SMAC) algorithm. The simulation results show that compared with traditional data source models, TSCBR model can significantly improve accuracy of the algorithm evaluation.

Time-varying gravity field model of Sichuan-Yunnan region based on the equivalent mass source model

High-precision time-varying gravity field is an effective way to study the internal mass movement and understanding the spatio-temporal evolution process of the geodynamic system.Compared to the satellite gravity measurement,the repeated terrestrial gravity observation can provide a more high-order signal related to the shallow crust and subsurface.However,the suitable and unified method for gravity model estimation is a key problem for further applications.In this study,we introduce the spherical hexahedron element to simulate the field source mass and forward model the change of gravity field located at the Sichuan-Yunnan region(99—104°E,23—29°N)in the four epochs from 2015 to 2017.Compared to the experimental results based on Slepian or spherical harmonics frequency domain method,this alternative approach is suitable for constructing the equivalent mass source model of regional-scale gravity data,by introducing the first-order smooth prior condition of gravity time-varying signal to suppress the high-frequency component of the signal.The results can provide a higher spatial resolution reference for regional gravity field modeling in the Sichuan-Yunnan region.

Regional Finite-Fault Source Model for Development of Ground Motion Attenuation Relationship in Sichuan, China

The attenuation relationship of ground motion based on seismology has always been a front subject of engineering earthquake.Among them,the regional finite-fault source model is very important.In view of this point,the general characteristics of regional seism-tectonics,including the dip and depth of the fault plane,are emphasized.According to the statistics of regional seism-tectonics and focal mechanisms in Sichuan,China,and the sensitivity of estimated peak ground acceleration(PGA)attenuation is analyzed,and the dip angle is taken as an average of 70°.Based the statistics of the upper crustal structure and the focal depth of regional earthquakes,the bottom boundary of the sedimentary cover can be used as the upper limit for estimating the depth of upper-edge.The analysis shows that this value is sensitive to PGA.Based on the analysis of geometric relations,the corresponding calculation formula is used,and a set of concepts and steps for building the regional finite-fault source model is proposed.The estimation of source parameters takes into account the uncertainty,the geometric relationship among parameters and the total energy conservation.Meanwhile,a set of reasonable models is developed,which lay a foundation for the further study of regional ground motion attenuation based on seismology.

MODEL OF LASER-TIG HYBRID WELDING HEAT SOURCE

The welding mechanism of laser-TIG hybrid welding process is analyzed. Withthe variation of arc current, the welding process is divided into two patterns: deep-penetrationwelding and heat conductive welding. The heat flow model of hybrid welding is presented. As todeep-penetration welding, the heat source includes a surface heat flux and a volume heat flux. Theheat source of heat conductive welding is composed of two Gaussian distribute surface heat sources.With this heat source model, a temperature field is calculated. The finite element code MARC isemployed for this purpose. The calculation results show a good agreement with the experimental data.

Inverse computation for cardiac sources using single current dipole and current multipole models

Two cardiac functional models are constructed in this paper. One is a single current model and the other is a current multipole model. Parameters denoting the properties of these two models are calculated by a least-square fit to the measurements using a simulated annealing algorithm. The measured signals are detected at 36 observation nodes by a superconducting quantum interference device （SQUID）. By studying the trends of position, orientation and magnitude of the single current dipole model and the current multipole model in the QRS complex during one time span and comparing the reconstructed magnetocardiography （MCG） of these two cardiac models, we find that the current multipole model is a more appropriate model to represent cardiac electrophysiological activity.

Heat source analyses of dual laser-beam bilateral synchronous welding for T-joint

The DLBSW（ dual laser-beam bilateral synchronous welding） technology of T-type joint has been widely used for the connection of skins and stringers in airplane industry. To understand the thermodynamic and mechanical behavior of this process, it is necessary to establish a reasonable heat source model. Two different surface-body combination heat source models are adopted in this paper. Both models use the Gaussian surface heat source model and one is combined with the cone body heat source model and the other is combined with Gaussian rotator body heat source model. The simulation results of these two different models are investigated. And the temperature field results of DLBSW process for T-joint with two different heat sources are discussed. It is indicated that the combination heat source model is effective to simulate the DLBSW process and the current study is useful for more profound research in this field.

Dynamic corner frequency in source spectral model for stochastic synthesis of ground motion

The static comer frequency and dynamic comer frequency in stochastic synthesis of ground motion from fi- nite-fault modeling are introduced, and conceptual disadvantages of the two are discussed in this paper. Furthermore, the non-uniform radiation of seismic wave on the fault plane, as well as the trend of the larger rupture area, the lower comer frequency, can be described by the source spectral model developed by the authors. A new dynamic comer frequency can be developed directly from the model. The dependence of ground motion on the size of subfault can be eliminated if this source spectral model is adopted in the synthesis. Finally, the approach presented is validated from the comparison between the synthesized and observed ground motions at six rock stations during the Northridge earthquake in 1994.

Simulation study of a magnetocardiogram based on a virtual heart model:effect of a cardiac equivalent source and a volume conductor

In this paper, we present a magnetocardiogram （MCG） simulation study using the boundary element method （BEM） and based on the virtual heart model and the realistic human volume conductor model. The different contributions of cardiac equivalent source models and volume conductor models to the MCG are deeply and comprehensively investigated. The single dipole source model, the multiple dipoles source model and the equivalent double layer （EDL） source model are analysed and compared with the cardiac equivalent source models. Meanwhile, the effect of the volume conductor model on the MCG combined with these cardiac equivalent sources is investigated. The simulation results demonstrate that the cardiac electrophysiological information will be partly missed when only the single dipole source is taken, while the EDL source is a good option for MCG simulation and the effect of the volume conductor is smallest for the EDL source. Therefore, the EDL source is suitable for the study of MCG forward and inverse problems, and more attention should be paid to it in future MCG studies.

Investigation on automated loading of dynamic 3D heat source model for welding simulation

Since programing complex and dynamic heat source model for welding simulation is a complex job,the parametric methods are studied in this paper.Firstly,an overall flow to achieve automatically modeling welding was introduced.Secondly,an expert module rule for selecting welding heat source model was founded,which is based on simulation knowledge and experiences.Thirdly,a modularity routine method was investigated using writing with C++programing,which automatically creates subroutines of 3D dynamic heat source model for user.To realize the dynamic weld path,the local weld path coordinate system was moved in the global coordinate system and it is used to model the direction of weld gun,welding path and welding pose.The weld path data file was prepared by the automatic tool for the welding heat source subroutines.All above functions were integrated in the user interface and the connection with architecture was introduced.At last,a laser beam welding heat source modeling was automatically modeled and the weld pool geometry was compared with the reported literature.It demonstrated that the automated tool is valid for welding simulation.Since modeling became convenient for welding simulation using the tool proposed,it could be easy and useful for welding engineers to acquire the needed information.

Turbocharger Noise Prediction Using Broadband Noise Source Model

The noise prediction of the turbocharger is studied.The broadband noise source model is employed to predict the near-field noise of the turbocharger.The 3D software Solidworks is adopted to establish the model blades and inlet of turbocharger compressor,then this 3D model is introduced into the software CFD to calculate the flow-field under different inlet shapes,different blades shapes and different clearances between casing and impeller.On the base of the above simulation,the broadband noise source model is employed to calculate and analyze the near-field noise.The calculation shows that compressor static pressure values and the sound power values near the impeller outlet are the largest.Through the noise calculation by using broadband noise source model under different inlet shapes and blade shapes,we find that the noise level of the inlet of cylindrical and cone types are smaller.Compared with the current widespread used backward skewed or radial blades,there is little difference of the noise value of the inlet of the forward skewed blades.

Dissipation source function and an improvement to LAGFD-WAM model

In this paper, a new theoretical expression of dissipation term is presented on the basis of statistical model of breaking wave, which is an improvement to LAGFD-WAM wave model. The computational results in three typical wind fields show a good improvement to LAGFD-WAM model and a better accuracy in comparison with the observed data in the South China Sea.

Numerical study on wave loads and motions of two ships advancing in waves by using three-dimensional translating-pulsating source

A frequency domain analysis method based on the three-dimensional translating-pulsating （3DTP） source Green function is developed to investigate wave loads and free motions of two ships advancing on parallel course in waves. Two experiments are carried out respectively to mea- sure the wave loads and the free motions for a pair of side-by- side arranged ship models advancing with an identical speed in head regular waves. For comparison, each model is also tested alone. Predictions obtained by the present solution are found in favorable agreement with the model tests and are more accurate than the traditional method based on the three dimensional pulsating （3DP） source Green function. Numer- ical resonances and peak shift can be found in the 3DP pre- dictions, which result from the wave energy trapped in the gap between two ships and the extremely inhomogeneous wave load distribution on each hull. However, they can be eliminated by 3DTP, in which the speed affects the free sur- face and most of the wave energy can be escaped from the gap. Both the experiment and the present prediction show that hydrodynamic interaction effects on wave loads and free motions are significant. The present solver may serve as a validated tool to predict wave loads and motions of two ves- sels under replenishment at sea, and may help to evaluate the hydrodynamic interaction effects on the ships safety in replenishment operation.

Study on the Source Parameters of Earthquakes in the Middle Eastern Area of North Tianshan in Xinjiang

By applying the empirical Green＇s function method, we first proved that the source spectra in the middle eastern area of North Tianshan follow the ω^-2 Brune model, and then, on this basis, obtained the source spectra for 105 earthquakes of ML 2.5 - 5.7 in the studied area upon removing the noise, instrument, propagation and site effects in the observational seismic S waveforms. Finally, we determined the source parameters such as the seismic moment, stress drop, source dimension, etc., based on the Brune model. The results show that there is a good linear correlation between scalar seismic moment, M0, and ML, which is Log10 M0 = 1.10 ML ＋ 17.20; The source radii range between 100- 1500m; the stress drop, 1-16MPa with a predominant range of 1 - 10MPa. The relationship of the seismic moment versus corner frequencies indicates that there may exist two source scaling, that is, when M0 〈 4×10^21 dyne. cm （equal to an ML4.0 event）, stress drop is weakly dependent on M0： whereas, when M0 〉 4×10^21 dyne·cm, stress drop is independent of M0.

Application of SWAT Model to Non-point Source Pollution in Xincai River Basin

[Objective]The study aimed to simulate the production and transportation process of surface runoff,sediment and non-point source pollution in Xincai River basin based on SWAT model.[Method]On the basis of analyzing the principles of SWAT model,the correlative parameters of runoff,sediment and water quality were calibrated,then the spatial and temporal distribution of runoff,sediment and non-point source pollutants in Xincai River basin were studied by using SWAT model.[Result]The results of calibration and validation showed that SWAT model was reasonable and available,and it can be used to simulate the non-point source pollution of Xincai River basin.The simulation results revealed that the load of sediment and various pollutants was the highest in the rainy year,followed by the normal year,while it was the minimum in the dry year,indicating that the production of sediment and non-point source pollutants was closely related to annual runoff.[Conclusion]The research could provide scientific references for the prevention of non-point source pollution in a basin.

Kinematic source model for simulation of near-fault ground motion field using explicit finite element method

This paper briefly reviews the characteristics and major processes of the explicit finite element method in modeling the near-fault ground motion field. The emphasis is on the finite element-related problems in the finite fault source modeling. A modified kinematic source model is presented, in which vibration with some high frequency components is introduced into the traditional slip time function to ensure that the source and ground motion include sufficient high frequency components. The model presented is verified through a simple modeling example. It is shown that the predicted near-fault ground motion field exhibits similar characteristics to those observed in strong motion records, such as the hanging wall effect, vertical effect, fling step effect and velocity pulse effect, etc.

Study on heat source model in twin-arc GMAW with a common weld pool

The heat input from arcs to weld pool in twin-arc gas metal arc welding （GMAW） with a common weld pool is investigated by high-speed photography. The characteristics of arc shapes and droplet transfer are studied and then the models for heat flux distribution on top surface of weld pool and enthalpy distribution of metal droplets transferred into weld pool are established. By using the model, 3-D geometries of weld pools in twin-arc GMAW with a common weld pool are predicted. Corresponding welding experiments on mild steel plates are carried out and the results indicate that the predicted shape of weld bead on cross section shows good agreement with measured one.

General expression of double ellipsoidal heat source model and its error analysis

In order to analyze the maximum power density error with different heat flux distribution parameter values for double ellipsoidal heat source model, a general expression of double ellipsoidal heat source model was derived .front Goldak double ellipsoidal heat source model, and the error of maximum power density was analyzed under this foundation. The calculation error of thermal cycling parameters caused by the maximum power density error was compared quantitatively by numerical simulation. The results show that for guarantee the accuracy of welding numerical simulation, it is better to introduce an error correction coefficient into the Goldak double ellipsoidal heat source model expression. And, heat flux distribution parameter should get higher value for the higher power density welding methods.