Application of bi-directional static loading test to deep foundations

Bi-directional static loading test adopting load cells is widely used around the world at present, with increase in diameter and length of deep foundations. In this paper, a new simple conversion method to predict the equivalent pile head load-settlement curve considering elastic shortening of deep foundation was put forward according to the load transfer mechanism. The proposed conversion method was applied to root caisson foundation in a bridge and to large diameter pipe piles in a sea wind power plant. Some new load cells, test procedure, and construction technology were adopted based on the applications to different deep foundations, which could enlarge the application scopes of bi-directional loading test. A new type of bi-directional loading test for pipe pile was conducted, in which the load cell was installed and loaded after the pipe pile with special connector has been set up. Unlike the conventional bi-directional loading test, the load cell can be reused and shows an evident economic benefit.

Static loading and vertical displacement at southern Siberia

Seismic method is usually used for elastic parametric estimation. This is why this method presents dynamic parameters of Earth. Frequency seismic range changes greatly from geodynamic modelling time. Now we have opportunity to use geodesy result for some years for elastic parameters estimation. Static solution from elastic theory may be used for the interpretation of long term results. It presents static elastic parameter. The inverse problem for different types of vertical surface loading on one year period is calculated. Two cases of loading with maximal and minimal area are presented. Results are determined by space geodesy and leveling methods. Current relation between atmospheric pressure and vertical displacements was estimated at the center of Siberian Anti Cyclone with size varied from 2000 km to 3000 kin. Pressure-displacement coefficients （PDC） can be achieved by three years obser- vation （0.997 mm/mbar for NVSK GPS station）. It is used for elastic module study of geology medium with maximum thickness up to 600 km. In the context of elastic model, the modulus of rigidity is estimated to be 113 GPa. Vast expanse of anti-cyclone may relate with rheology of crust and upper mantle. Smaller size of surface loading - local loading is seasonal variation of water reservoir. Annual vertical changes were obtained by leveling near the dam of the reservoir. PDC ratio was 1.15 mm/bar for these places. In elastic theory, the Young modulus E = 80 GPa （Poisson ratio = 0.25, the modulus of rigidity - 32 GPa） was calculated by sixteen years of leveling measurements. This result can effectively be represented for upper crust. Our results were checked by solution for coseismic displacement of Chyia- Altai earthquake （Sep. 27, 2003, M = 7.3）. Coseismic results calculated by static modules agree with experimental coseismic GPS data at 10% level.

Multi-Channel Force Control System for Static Loading

An eight-channel force loading system is presented, which adopts position control system and force control system switching model, small flow servo valve controlled capacious cylinder system scheme, intelligent PID algorithm and distributed load approach. Through the analyses of the equivalent model of valve controlled cylinder force subsystem, a controller based on intelligent PID algorithm is designed, which is not sensitive to the variation of parameters such as environmental stiffness. According to the coupling of multiple load channels, a distributed load approach is employed in the superior monitor computer. Experimental results show that the system designed has high precision and robustness.

Mechanical behavior and failure mechanisms of rock bolts subjected to static-dynamic loads

This study explores the effects of dynamic and static loading on rock bolt performance a key factor in maintaining the structural safety of coal mine roadways susceptible to coal bursts.Employing a housemade load frame to simulate various failure scenarios,pretension-impact-pull tests on rock bolts were conducted to scrutinize their dynamic responses under varied static load conditions and their failure traits under combined loads.The experimental results denote that with increased impact energy,maximum and average impact loads on rock bolts escalate significantly under pretension,initiating plastic deformation beyond a certain threshold.Despite minor reductions in the yield load due to impactinduced damage,pretension aids in constraining post-impact deformation rate and fluctuation degree of rock bolts.Moreover,impact-induced plastic deformation causes internal microstructure dislocation,fortifying the stiffness of the rock bolt support system.The magnitude of this fortification is directly related to the plastic deformation induced by the impact.These findings provide crucial guidance for designing rock bolt support in coal mine roadway excavation,emphasizing the necessity to consider both static and dynamic loads for improved safety and efficiency.

Energy mechanism of bolt supporting effect to fissured rock under static and dynamic loads in deep coal mines

The stability control of fissured rock is difficult,especially under static and dynamic loads in deep coal mines.In this paper,the dynamic mechanical properties,strain rate evolution and energy dissipation of fissured and anchored rocks were respectively obtained by SHPB tests.It was found that bolt can provide supporting efficiency-improving effect for fissured rock against dynamic disturbance,and this effect increased quadratically with decrease in anchoring angles.Then,the energy dissipation mechanism of anchored rock was obtained by slipping model.Furthermore,bolt energy-absorbing mechanism by instantaneous tensile-shear deformation was expressed based on material mechanics,which was the larger the anchoring angle,the smaller the energy absorption,and the less the contribution to supporting efficiency improvement.On this basis,the functional relationship between energy dissipation of anchored rock and energy absorption of bolt was established.Taking the coal-gangue separation system of Longgu coal mine as an example,the optimal anchoring angle can be determined as 57.5°–67.5°.Field monitoring showed fissured rock with the optimal anchoring angle,can not only effectively control the deformation,but also fully exert the energy-absorbing and efficiency-improving effect of bolt itself.This study provides guidance to the stability control and supporting design for deep engineering under the same or similar conditions.

Analysis of the Application of Static Load Test in Bridge Bearing Capacity Testing

This article uses real engineering projects as examples to analyze how static load test technology is applied in testing the bridge-bearing capacity.The analysis covers aspects such as testing section layout,test load and efficiency coefficient,loading plan,evaluation optimization,test result modification,and result evaluation.The aim is to support the accurate detection and evaluation of bridge-bearing capacity.

Effects of Microstructure on Quasi⁃Static Transverse Loading Behavior of 3D Circular Braided Composite Tubes

The effects of microstructure on quasi-static transverse loading behavior of 3D circular braided composite tubes were studied. Transverse loading tests were conducted. Transverse load-deflection curves were obtained to analyze the effects of braiding parameters including the braiding angle, the wall thickness, and the diameter on the transverse loading of 3D circular braided composite tubes. Breaking loads, moduli and strengths had also been used to describe the transverse loading behaviors. The failure morphologies were shown to reveal damage mechanisms. From the results, the increase in braiding angle, wall thickness and diameter increases the ability of anti-deformation and breaking load of braided tubes. The breaking load of specimen with a braiding angle of 45° is about 1.68 times that of specimen with a braiding angle of 15°. The breaking load of specimen with 4 layers of yarns is about 2.15 times that of specimen with 2 layers of yarns. The breaking load of the tube with a diameter of 25.5 mm is about 2.39 times that of the tube with a diameter of 20.5 mm.

Collapse and Reinforcement of Pipe-Framed Greenhouse under Static Wind Loading

The present paper investigates the collapse process of a pipe-framed greenhouse under static wind loading based on a non-linear finite element analysis.The purpose is to establish a more reasonable wind resistant design method for such structures.The structures are so flexible that the fluid-structure interaction(FSI)is considered in the analysis.In practice,iterative analyses of the structure’s response and the wind pressure distribution on the deformed structure are made.The wind direction is normal to the ridge.Computational fluid dynamics(CFD)analysis with a RANS turbulence model is used for evaluating the time-averaged wind pressure coefficient distribution on the structure.Both the geometric and the material non-linearity are considered in the structural analysis.The collapse behavior obtained is consistent with the practical one often observed in damage investigations.Based on the results,discussion is made of the validity of the current design guideline commonly used in Japan.The same analysis is carried out for various reinforced models.The effect of each reinforcement method on the improvement of wind resistance of the structure is investigated on the basis of the allowable stress and deformation limits specified in the current design guideline.

Technical Analysis of Highway Bridge Static Load Test

Highway bridges are an important part of the transportation industry and can promote social economic construction and development.In actual operation,highway bridges are often damaged due to overload and natural factors,which tend to affect the safety and shorten the service life of these bridges.Assessing the overall state and performance of highway bridges is therefore a key element.Static load test,which is a type of sustainable detection experiment,has many advantages,including low cost,high efficiency,and high accuracy.In this paper,the bridge structure is analyzed through the application of theoretical calculations and relevant comparisons,so as to judge the operating state of the bridge.

Static Load Test Detection of Continuous Rigid- Frame Railway Bridge

The quality of the continuous rigid-frame railway bridge is related to the safety of train operation,so it is necessary to test its stiffness,strength,and other indicators.Static load test is a common technique for bridge inspection.This article summarizes the purpose of the static load test for a continuous rigid-frame railway bridge,including the required equipment,operation methods,etc.,and lists examples to analyze the operation process and precautions of static load test,hoping to provide reference information for relevant personnel.

Dynamic mechanical characteristics of deep Jinping marble in complex stress environments

To reveal the dynamic mechanical characteristics of deep rocks,a series of impact tests under triaxial static stress states corresponding to depths of 300-2400 m were conducted.The results showed that both the strain rates and the stress environments in depth significantly affect the mechanical characteristics of rocks.The sensitivity of strain rate to the dynamic strength and deformation modulus shows a negative correlation with depth,indicating that producing penetrative cracks in deep environments is more difficult when damage occurs.The dynamic strength shows a tendency to decrease and then increase slightly,but decreases sharply finally.Transmissivity demonstrates a similar trend as that of strength,whereas reflectivity indicates the opposite trend.Furthermore,two critical depths with high dynamically induced hazard possibilities based on the China Jinping Underground Laboratory(CJPL)were proposed for deep engineering.The first critical depth is 600-900 m,beyond which the sensitivity of rock dynamic characteristics to the strain rate and restraint of circumferential stress decrease,causing instability of surrounding rocks under axial stress condition.The second one lies at 1500-1800 m,where the wave impedance and dynamic strength of deep surrounding rocks drop sharply,and the dissipation energy presents a negative value.It suggests that the dynamic instability of deep surrounding rocks can be divided into dynamic load dominant and dynamic load induced types,depending on the second critical depth.

Analysis of rockburst in tunnels subjected to static and dynamic loads

The presence of geological structures such as faults, joints, and dykes has been observed near excavation boundaries in many rockburst case histories. In this paper, the role of discontinuities around tunnels in rockburst occurrence was studied. For this purpose, the Abaqus explicit code was used to simulate dynamic rock failure in deep tunnels. Material heterogeneity was considered using Python scripting in Abaqus. Rockbursts near fault regions in deep tunnels under static and dynamic loads were studied.Several tunnel models with and without faults were built and static and dynamic loads were used to simulate rock failure. The velocity and the released kinetic energy of failed rocks, the failure zone around the tunnel, and the deformed mesh were studied to identify stable and unstable rock failures. Compared with models without discontinuities, the results showed that the velocity and the released kinetic energy of failed rocks were higher, the failure zone around the tunnel was larger, and the mesh was more deformed in the models with discontinuities, indicating that rock failure in the models with discontinuities was more violent. The modeling results confirm that the presence of geological structures in the vicinity of deep excavations could be one of the major influence factors for the occurrence of rockburst. It can explain localized rockburst occurrence in civil tunnels and mining drifts. The presented methodology in this paper for rockburst analysis can be useful for rockburst anticipation and control during mining and tunneling in highly stressed ground.

NMR-based damage characterisation of backfill material in host rock under dynamic loading

It is not uncommon that backfill material used in underground mining being exposed to repetitive dynamic stresses induced by blasting operations or rockburst events. Understanding the strength and fracture evolution of backfilled stopes is critical to maintain the long-term stope stability and ensure safe mining activities. This paper aims to study the damage evolution of the backfill material and its host rock behaviour under three-dimensional(3D) dynamic loading. Using a true-triaxial testing machine, multiple samples of backfill material enclosed by country rock were fabricated and tested under various dynamic loadings with different true-triaxial confining stress conditions. In addition, the nuclear magnetic resonance(NMR) measurement was conducted on the samples before and after exerting static and dynamic loading to obtain their porosity distribution changes. The experiment results suggested that with the increase of the dynamic loading, the porosity of the backfill sample goes through a two-stage process,which shows a slightly linear decrease and then followed by an exponential increase. The research findings can help understand the damage mechanism and fracture development of backfilled stopes and its host rock in deep underground mines, which are constantly subject to the combination of 3D static confining stress and dynamic loading.

Grouping response method for equivalent static wind loads based on a modified LRC method

Wind loading is one of the most important loads for controlling the design of large-span roof structures. Equivalent static wind loads, which can generally aim at determining a specific response, are widely used by structural designers. A method for equivalent static wind loads applicable to multi-responses is proposed in this paper. A modified load- response-correlation （LRC） method corresponding to a particular peak response is presented, and the similarity algorithm implemented for the group response is described. The main idea of the algorithm is that two responses can be put into one group if the value of one response is close to that of the other response, when the structure is subjected to equivalent static wind loads aiming at the other response. Based on the modified LRC, the grouping response method is put forward to construct equivalent static wind loading. This technique can simultaneously reproduce peak responses for some grouped responses. To verify its computational accuracy, the method is applied to an actual large-span roof structure. Calculation results show that when the similarity of responses in the same group is high, equivalent static wind loads with high accuracy and reasonable magnitude of equivalent static wind distribution can be achieved.

Stability analysis of rib pillars in highwall mining under dynamic and static loads in open‑pit coal mine

The retained coal in the end slope of an open-pit mine can be mined by the highwall mining techniques.However,the instability mechanism of the reserved rib pillar under dynamic loads of mining haul trucks and static loads of the overlying strata is not clear,which restricts the safe and efcient application of highwall mining.In this study,the load-bearing model of the rib pillar in highwall mining was established,the cusp catastrophe theory and the safety coefcient of the rib pillar were considered,and the criterion equations of the rib pillar stability were proposed.Based on the limit equilibrium theory,the limit stress of the rib pillar was analyzed,and the calculation equations of plastic zone width of the rib pillar in highwall mining were obtained.Based on the Winkler foundation beam theory,the elastic foundation beam model composed of the rib pillar and roof under the highwall mining was established,and the calculation equations for the compression of the rib pillar under dynamic and static loads were developed.The results showed that with the increase of the rib pillar width,the total compression of the rib pillar under dynamic and static loads decreases nonlinearly,and the compression of the rib pillar caused by static loads of the overlying strata and trucks has a decisive role.Numerical simulation and theoretical calculation were also performed in this study.In the numerical simulation,the coal seam with a buried depth of 122 m and a thickness of 3 m is mined by highwall mining techniques.According to the established rib pillar instability model of the highwall mining system,it is found that when the mining opening width is 3 m,the reasonable width of the rib pillar is at least 1.3 m,and the safety factor of the rib pillar is 1.3.The numerical simulation results are in good agreement with the results of theoretical calculation,which verifes the feasibility of the theoretical analysis of the rib pillar stability.This research provides a reference for the stability analysis of rib pillars under highwall mining.

Nonlinear Resonance of the Rotating Circular Plate under Static Loads in Magnetic Field

The rotating circular plate is widely used in mechanical engineering, meanwhile the plates are often in the electromagnetic field in modern industry with complex loads. In order to study the resonance of a rotating circular plate under static loads in magnetic field, the nonlinear vibration equation about the spinning circular plate is derived according to Hamilton principle. The algebraic expression of the initial deflection and the magneto elastic forced disturbance differential equation are obtained through the application of Galerkin integral method. By mean of modified Multiple scale method, the strongly nonlinear amplitude-frequency response equation in steady state is established. The amplitude frequency characteristic curve and the relationship curve of amplitude changing with the static loads and the excitation force of the plate are obtained according to the numerical calculation. The influence of magnetic induction intensity, the speed of rotation and the static loads on the amplitude and the nonlinear characteristics of the spinning plate are analyzed. The proposed research provides the theory reference for the research of nonlinear resonance of rotating plates in engineering.

Stability Analysis of Bohai Oil-Drilling Ship No. 6 Under Static and Cyclic Loads

This paper presents a procedure to calculate the safety factor against sliding of a marine gravity structure subjected to a combination of static and cyclic loads. This procedure claculates the stress at the sliding surface by the finite element method (FEM) and takes the dynamic properties of clay into account. With this procedure, the stability of a Bohai oil-drilling ship is analyzed. The calculated safety factor is much smaller than 1, indicating that this oil-drilling ship would fail just as what had happened to it.

NONLINEAR FREE VIBRATION OF ORTHOTROPIC SHALLOW SHELLS OF REVOLUTION UNDER THE STATIC LOADS

In this paper, the axisymmetric nonlinear free vibration problems of cylindrically orthotropic shallow thin spherical and conical shells under uniformly distributed static loads are studied by using MWR and Lindstedt-Poincare perturbation method, from which, the characteristic relation between frequency ratio and amplitude is obtained. The effects of static loads, geometric and material parameters on vibrational behavior of shells are also discussed.

MDSLB:A new static load balancing method for parallel molecular dynamics simulations

Large-scale parallelization of molecular dynamics simulations is facing challenges which seriously affect the simula- tion efficiency, among which the load imbalance problem is the most critical. In this paper, we propose, a new molecular dynamics static load balancing method （MDSLB）. By analyzing the characteristics of the short-range force of molecular dynamics programs running in parallel, we divide the short-range force into three kinds of force models, and then pack- age the computations of each force model into many tiny computational units called ＂cell loads＂, which provide the basic data structures for our load balancing method. In MDSLB, the spatial region is separated into sub-regions called ＂local domains＂, and the cell loads of each local domain are allocated to every processor in turn. Compared with the dynamic load balancing method, MDSLB can guarantee load balance by executing the algorithm only once at program startup without migrating the loads dynamically. We implement MDSLB in OpenFOAM software and test it on TianHe-lA supercomputer with 16 to 512 processors. Experimental results show that MDSLB can save 34%-64% time for the load imbalanced cases.

Solid Model Bridge Static Damage Monitoring Based on GBSAR

Bridge deformation monitoring usually adopts contact sensors,and the implementation process is often limited by the environment and observation conditions,resulting in unsatisfactory monitoring accuracy and effect.Ground-Based Synthetic Aperture Radar(GBSAR)combined with corner reflectors was used to perform static load-loaded deformation destruction experiments on solid model bridges in a non-contact manner.The semi parametric spline filtering and its optimization method were used to obtain the monitoring results of the GBSAR radar’s line of sight deformation,and the relative position of the corner reflector and the millimeter level deformation signals under different loading conditions were successfully extracted.The deformation transformation model from the radar line of sight direction to the vertical vibration direction was deduced.The transformation results of deformation monitoring and the measurement data such as the dial indicator were compared and analyzed.The occurrence and development process of bridge deformation and failure were successfully monitored,and the deformation characteristics of the bridge from continuous loading to eccentric loading until bridge failure were obtained.The experimental results show that GBSAR combined with corner reflector can be used for deformation feature acquisition,damage identification and health monitoring of bridges and other structures,and can provide a useful reference for design,construction and safety evaluation.