The trial-and-error method is widely used for the current optimization of the steel casting feeding system, which is highly random, subjective and thus ineff icient. In the present work, both the theoretical and the e...The trial-and-error method is widely used for the current optimization of the steel casting feeding system, which is highly random, subjective and thus ineff icient. In the present work, both the theoretical and the experimental research on the modeling and optimization methods of the process are studied. An approximate alternative model is established based on the Back Propagation(BP) neural network and experimental design. The process parameters of the feeding system are taken as the input, the volumes of shrinkage cavities and porosities calculated by simulation are simultaneously taken as the output. Thus, a mathematical model is established by the BP neural network to combine the input variables with the output response. Then, this model is optimized by the nonlinear optimization function of the genetic algorithm. Finally, a feeding system optimization of a steel traveling wheel is conducted. No shrinkage cavities and porosities are induced through the optimization. Compared to the initial design scheme, the process yield is increased by 4.1% and the volume of the riser is decreased by 5.48×10~6 mm3.展开更多
The present study designed two kinds of Fe-18Mn-1.3C-2Cr-(4,11)Al(wt.%)low-density steels.Tensile and impact tests were carried out to evaluate the work hardening and impact toughness properties via aluminum(Al)alloyi...The present study designed two kinds of Fe-18Mn-1.3C-2Cr-(4,11)Al(wt.%)low-density steels.Tensile and impact tests were carried out to evaluate the work hardening and impact toughness properties via aluminum(Al)alloying control.Meanwhile,microstructure evolution and fracture morphology were investigated by X-ray diffraction(XRD),a scanning electron microscope(SEM)equipped with electron backscatter diffraction(EBSD),a transmission electron microscope(TEM),and a stereo-optical microscope(OM).It is found that the Al addition obviously promotes the dislocation planar slipping,resulting in cleavage and brittle impact fracture in 11wt.%Al steel.Besides,the microband-induced plasticity(MBIP)mechanism is found in 4wt.%Al containing steel,introducing considerable work hardening capacity and impact toughness of 156.8±17.4 J.The present study provides a direct illustration of the relationship between work hardening and impact toughness behaviors of these two low-density steels for potential application as impact-resistant components.展开更多
The effect of main alloying elements on thermal wear of cast hot-forging die steels was studied. The wear mechanism was discussed. The results show that alloying elements have significant influences on the thermal wea...The effect of main alloying elements on thermal wear of cast hot-forging die steels was studied. The wear mechanism was discussed. The results show that alloying elements have significant influences on the thermal wear of cast hot-forging die steels. The wear rates decrease with an increase in chromium content from 3% to 4% and molybdenum content from 2% to 3%, respectively. With further increase of chromium and molybdenum contents, chromium slightly reduces the wear resistance and molybdenum severely deteriorates the wear resistance with high wear rate. Lower vanadium/carbon ratio (1.5-2.5) leads to a lower wear resistance with higher wear rate. With an increase in vanadium/carbon ratio, the wear resistance of the cast steel substantially increases. When vanadium/carbon ratio is 3, the wear rate reaches the lowest value. The predominant mechanism of thermal wear of cast hot-forging die steels are oxidation wear and fatigue delamination. The Fe2O3 and Fe3O4 or lumps of brittle wear debris are formed on the wear surface.展开更多
The influence of microalloying additions on the mechanical properties of a low-carbon cast steel containing combinations of V, Nb, and Ti in the as-cast condition was evaluated. Tensile and hardness test results indic...The influence of microalloying additions on the mechanical properties of a low-carbon cast steel containing combinations of V, Nb, and Ti in the as-cast condition was evaluated. Tensile and hardness test results indicated that good combinations of strength and ductility could be achieved by V and Nb additions. While the yield strength and UTS (ultimate tensile strength) increased up to the range of 378-435 MPa and 579- 590 MPa, respectively in the microalloyed heats, their total elongation ranged from 18% to 23%. The presence of Ti, however, led to some reduction in the strength. Microstructural studies including scanning electron microscopy (SEM) and optical microscopy revealed that coarse TiN particles were responsible for this behavior. The Charpy impact values of all compositions indicated that microalloying additions significantly decreased the impact energy and led to the dominance of cleavage facets on the fracture surfaces. It seems that the increase in the hardness of coarse ferrite grains due to the precipitation hardening is the main reason for brittle fracture.展开更多
The toughness of 31Mn2SiRE wear-resistance cast steel were increased by means of RE compound modification and high temperature austenitizing. The results show that the microstructures can be refined, needle and networ...The toughness of 31Mn2SiRE wear-resistance cast steel were increased by means of RE compound modification and high temperature austenitizing. The results show that the microstructures can be refined, needle and network ferrite are eliminated, the dislocation density and the quantity of dislocated martensite are increased remarkably, and the shape and distribution of inclusions are improved by the addition of RE. Therefore, the mechanical properties of the modified steel can be greatly increased, especially the toughness (αK) by 44%, yield strength (σs) by 10%, and elongation (δ5) by 42%.展开更多
Thermal wear of cast hot-forging die steel modified by rare earths(RE) was studied and compared with commercially used die steels. The function of RE and the mechanism of thermal wear of cast steel modified by RE we...Thermal wear of cast hot-forging die steel modified by rare earths(RE) was studied and compared with commercially used die steels. The function of RE and the mechanism of thermal wear of cast steel modified by RE were discussed. The results showed that with increasing content of RE, the wear rate of cast steel reduced at first and then increased. By adding 0.05% (mass fraction) RE, the cast hot-forging die steel with optimum thermal wear resistance was obtained, which was better than that of H13 and 3Cr2WSV. The large amount of coarse inclusions, (RE)2O2S, resulted from excessive RE, which obviously deteriorated thermal wear resistance. The mechanism of thermal wear of the modified cast die steel is oxidation wear and oxide fatigue delamination. The wear debris are lumps of Fe2O3 and Fe3O4.展开更多
With the help of solidification kinetics, precipitation and growth of TiNhave been studied theoretically and the effect of cooling rate on the growth of TiN has beendiscussed. Through induction electric furnace experi...With the help of solidification kinetics, precipitation and growth of TiNhave been studied theoretically and the effect of cooling rate on the growth of TiN has beendiscussed. Through induction electric furnace experiment and electroslag remelting experiment withdifferent cooling rates, the distribution and particle size of TiN were investigated. It is provedthat the higher cooling rate is, the smaller the final size of TiN is and the more TiN particles canbe found in the steel. That TiN can restrain the growth of columnar crystal and enhance theproportion of equiaxed crystals to refine solidification structure as the heterogeneous nucleationsites of δ-ferrite is confirmed preliminarily. A new method to reduce macrosegregation incontinuous cast steel is provided.展开更多
In isothermal spheroidizing process,the spheroidization and growth of the carbide formed in hot-deformed high-carbon chromium cast steel at high temperature were investigated.The results showed that the spheroidizing ...In isothermal spheroidizing process,the spheroidization and growth of the carbide formed in hot-deformed high-carbon chromium cast steel at high temperature were investigated.The results showed that the spheroidizing growth of carbide proceeds in such a way that the bigger carbide particles swallow the smaller ones,and the short rhabdoid carbides dissolve and are spheroidized by itself.When the samples were held at 720℃ for more than 3 h,the spheroidization is not obvious.The feature of the process is the size increment and the amount decrement of carbide particles.The empirical equation for growth rate of carbides was obtained.The volume fraction of carbides keeps constant.The growth process agrees well with Ostwald Ripening Law.展开更多
The microstructure and properties of high carbonic-chromium cast steel subjected to different hot deformation ratios were studied.The experimental results show that the microstructure and properties of high carbonic-c...The microstructure and properties of high carbonic-chromium cast steel subjected to different hot deformation ratios were studied.The experimental results show that the microstructure and properties of high carbonic-chromium cast steel are obviously improved after hot deformation,and the best mechanical properties of the cast steel can be obtained under hot deformation ratio of 40 %-50 %,which leads to the morphology change of eutectic carbide and the precipitation of granular carbides.展开更多
The dendrite segregation in cast H13 steel was weakened with RE modification treatment. Grain boundary carbide during quenching was also under control and impact toughness was improved greatly. By thermodynamic calcul...The dendrite segregation in cast H13 steel was weakened with RE modification treatment. Grain boundary carbide during quenching was also under control and impact toughness was improved greatly. By thermodynamic calculation, analysis of two-dimensional lattice misfitting and electron probe analysis, it is found that Ce2O3 may act as the heterogeneous nuclei of modified cast H13 steel.展开更多
A new type of Nb-V-Ti microalloyed cast steel was produced. Computer simulation was adopted to optimize the content of alloying elements. The microstructure of the microalloyed steel was analyzed. The fatigue property...A new type of Nb-V-Ti microalloyed cast steel was produced. Computer simulation was adopted to optimize the content of alloying elements. The microstructure of the microalloyed steel was analyzed. The fatigue property, wear and friction properties and rupture toughness of the steel were investigated. The service and operating properties of Nb-V-Ti microalloyed cast steel coupler were also examined. The results show that the steel has excellent comprehensive mechanical properties. The granular bainite structure and precipitation strengthening are the primary strengthening mechanism. The fine grain brings the steel good plasticity and excellent toughness. Various service and operating properties of Nb-V-Ti microalloyed cast steel automatic coupler are excellent.展开更多
Due to traffic and wave actions, cast steel joints are subjected to variable-amplitude fatigue loading, which may cause fatigue problems. The ratio of the minimum strain to the maximum strain(strain ratio)can be emplo...Due to traffic and wave actions, cast steel joints are subjected to variable-amplitude fatigue loading, which may cause fatigue problems. The ratio of the minimum strain to the maximum strain(strain ratio)can be employed to analyze the influence of variable-amplitude fatigue both in the elastic and plastic ranges. To evaluate the effect of the strain ratio on G20Mn5 QT cast steel, the fatigue tests of smooth specimens were carried out at the strain ratio of 0.1. The cyclic deformation and the relationships between the strain amplitude, the stress amplitude, the Smith, Watson and Topper(SWT)parameter and fatigue life were studied and compared with those at the strain ratio of-1. Compared with other methods, Basquin formula and Solonberg formula provide reliable and appropriate ranges of S-N curve and fatigue limit at different strain ratios respectively. The SWT parameter can be used to predict the fatigue life at other strain ratios accurately.展开更多
The effects of RE modification on structure and the properties of a new cast hot work die (CHD) steel were investigated. The grains of the CHD steel are refined by RE modification. With the increase of RE addition, b...The effects of RE modification on structure and the properties of a new cast hot work die (CHD) steel were investigated. The grains of the CHD steel are refined by RE modification. With the increase of RE addition, both grain size and inclusion amount are reduced. Appropriate amount of RE results in decrease in inclusion amount and formation of spheroidal inclusions uniformly-distributed in steel, so that the morphology and distribution of inclusions are improved. RE composite modification favors the formation of bainite, austenite and fine lath martensite with dense dislocation. When the residual RE content reaches 0.02%, no obvious changes in strength and hardness are found, while fracture toughness and threshold of fatigue crack growth are increased. The impact toughness, elongation and reduction of cross sectional area are increased by a factor of two, and thermal fatigue resistance is also improved.展开更多
The effect of rare earth (Re) and titanium (Ti) multi-modification on the impact wear behavior of Mn-B high-Si bainitic cast steel was investigated systematically. The experiments show that the impact wear resista...The effect of rare earth (Re) and titanium (Ti) multi-modification on the impact wear behavior of Mn-B high-Si bainitic cast steel was investigated systematically. The experiments show that the impact wear resistance can be improved greatly with the addition of Re and Ti. Its wear loss is only about 1/3-1/2 as large as that of the unmodified bainitic cast steel. By the Re/Ti modification, coarse dendrite grains and bainitic/martensite duplex structure have been refined effectively, and the impact toughness of the bainitic cast steel is nearly tripled (10 mm×10 mm×55 mm, with unnotched sample). Consequently, the modified bainitic cast steel possesses good wear resistance under high im- pact. For both modified and unmodified bainitic cast steels, high hardness white layer and deformed zone are developed beneath the worn surface under the high impact wear, but the formation and propagation of cracks are different for these bainitic casting steels. Different mod- els for the formation and propagation of cracks for both modified and unmodified bainitic cast steels under high impact wear are proposed.展开更多
The effects of Si content on combinations of important properties such as hardness, hardenability, and weldability in addition to strength increment were systematically investigated to develop a Mo and V free low allo...The effects of Si content on combinations of important properties such as hardness, hardenability, and weldability in addition to strength increment were systematically investigated to develop a Mo and V free low alloy cast steel for automobile cold pressing die insert. For the evaluation of the applicability as the die insert, the mechanical properties were measured after spheroidization annealing (SA), quenching and tempering (Q/T), and flame hardening (FH) treatments, respectively. The developed 0.8%-1.6%Si containing Mo and V free alloy cast steels showed excellent matrix strengthening effect, hardenability, and weldability, fulfilling the industrial criterion of the mechanical properties for the die insert.展开更多
This paper presents the shear performance analysis of a heavy-duty universal hinged cast steel support with the largest bearing capacity. The effect of 9 parameters ( 52 specimens) ,i. e. height of the upper support,d...This paper presents the shear performance analysis of a heavy-duty universal hinged cast steel support with the largest bearing capacity. The effect of 9 parameters ( 52 specimens) ,i. e. height of the upper support,depth of the ring of the upper support,depth of the top plate of the bottom support,height of the ribs of the bottom support,depth of the ribs of the bottom support,bolt hole diameter,number of the ribs of the bowl,depth of the ribs of the bowl,and yield strength of the material,were analyzed with a 3-dimensional elastic-plastic finite element model in which the nonlinearities of geometry,material and contact were all considered. Analysis shows that height of the upper support,depth of the ring of the upper support and yield strength of the material have a great effect on the mechanical performance of the support. Height of the upper support has the largest effect on performance price ratio of the support,and the maximum effect can be up to 160% . Depth of the top plate of the bottom support,height of the ribs of the bottom support and depth of the ribs of the bottom support have a medium effect on performance price ratio of the support,and the effect is within the limit of 15% 19% .展开更多
The dynamic recrystallization(DRX) simulation performance largely depends on simulated grain topological struc?tures. However, currently solutions used di erent models for describing two?dimensional(2 D) and three?dim...The dynamic recrystallization(DRX) simulation performance largely depends on simulated grain topological struc?tures. However, currently solutions used di erent models for describing two?dimensional(2 D) and three?dimensional(3 D) grain size distributions. Therefore, it is necessary to develop a more universal simulation technique. A cellular automaton(CA) model combined with an optimized topology deformation technology is proposed to simulate the microstructural evolution of 42 CrMo cast steel during DRX. In order to obtain values of material constants adopted in the CA model, hot deformation characteristics of 42 CrMo cast steel are investigated by hot compression metal?lographic testing. The proposed CA model deviates in two important aspects from the regular CA model. First, an optimized grain topology deformation technology is utilized for studying the hot compression e ect on the topology of grain deformation. Second, the overlapping grain topological structures are optimized by using an independent component analysis method, and the influence of various thermomechanical parameters on the nucleation process, grain growth kinetics, and mean grain sizes observed during DRX are explored. Experimental study shows that the average relative root mean square error(RRMSE) of the mean grain diameter obtained by the regular CA model is equal to 0.173, while the magnitude calculated using the proposed optimized CA model is only 0.11. This paper pro?poses a novel combined CA model for simulating the microstructural evolution of 42 CrMo cast steel, which notably uses a ICA?based grain topology deformation method to optimize the overlapping grain topological structures in simulation.展开更多
The intergranular cracking of 9% Ni cast steel seems mainly to relate to the segregation of contaminates H,S and P along boundaries.An addition of rare earth may eliminate the seg- regation of these contaminates along...The intergranular cracking of 9% Ni cast steel seems mainly to relate to the segregation of contaminates H,S and P along boundaries.An addition of rare earth may eliminate the seg- regation of these contaminates along grain boundaries and improve the binding force among boundaries,so as to reduce remarkably the intergranular cracking.展开更多
The step pattern of single crystal growth and the morphology at equilibrium state of(Mn, Fe)S on the wall of micro-voids in ZG25 cast steel have been observed using scanning electron microscope.The face-centred cubic(...The step pattern of single crystal growth and the morphology at equilibrium state of(Mn, Fe)S on the wall of micro-voids in ZG25 cast steel have been observed using scanning electron microscope.The face-centred cubic(Mn,Fe)S single crystal at equilibrium state is shown to be tetrakaidecahedron consisted of eight{111}planes and six{100}planes,and is a typical example of the O_h—m3m cubic crystal system.展开更多
The oxidation behaviors of three austenitic cast steels with different morphologies of primary carbides at 950℃ in air were investigated using scanning electron microscopy,energy dispersive spectroscopy,and focused i...The oxidation behaviors of three austenitic cast steels with different morphologies of primary carbides at 950℃ in air were investigated using scanning electron microscopy,energy dispersive spectroscopy,and focused ion beam/transmission electron microscopy.Their oxidation kinetics followed a logarithmic law,and the oxidation rate can be significantly decreased as long as a continuous silica layer formed at the scale/substrate interface.When the local Si concentration was inadequate,internal oxidation occurred beneath the oxide scale.The spallation of oxides during cooling can be inhibited with the formation of internal oxidation,owing to the reduced mismatch stress between the oxide scale and the substrate.The“Chinese-script”primary Nb(C,N)was superior to the dispersed primary Nb(C,N)in suppressing the oxidation penetration in the interdendritic region by supplying a high density of quick-diffusion Cr channels.In addition,the innermost and outermost oxidation layers were enriched with Cr,whereas the Cr evaporation in the outermost layer was significant when the water vapor concentration in the environment was high enough.These findings further the understanding regarding the oxidation behavior of austenitic cast steels and will promote the alloy development for exhaust components.展开更多
基金financially supported by the Program for New Century Excellent Talents in University(Nos.NCET-13-0229,NCET-09-0396)the National Science&Technology Key Projects of Numerical Control(Nos.2012ZX04010-031,2012ZX0412-011)the National High Technology Research and Development Program("863"Program)of China(No.2013031003)
文摘The trial-and-error method is widely used for the current optimization of the steel casting feeding system, which is highly random, subjective and thus ineff icient. In the present work, both the theoretical and the experimental research on the modeling and optimization methods of the process are studied. An approximate alternative model is established based on the Back Propagation(BP) neural network and experimental design. The process parameters of the feeding system are taken as the input, the volumes of shrinkage cavities and porosities calculated by simulation are simultaneously taken as the output. Thus, a mathematical model is established by the BP neural network to combine the input variables with the output response. Then, this model is optimized by the nonlinear optimization function of the genetic algorithm. Finally, a feeding system optimization of a steel traveling wheel is conducted. No shrinkage cavities and porosities are induced through the optimization. Compared to the initial design scheme, the process yield is increased by 4.1% and the volume of the riser is decreased by 5.48×10~6 mm3.
基金This work was financially supported by the Guangdong Province Key Area R&D Program(Grant No.2020B0101340004)the International Science and Technology Cooperation Project of Guangdong Province(Grant No.2021A0505030051)+2 种基金the Innovation and Technology Fund(ITF)(Grant No.ITP/020/21AP)the Young Talent Support Project of Guangzhou Association for Science and Technology(Grant No.QT20220101075)the GDAS'Project of Science and Technology Development(Grant No.2022GDASZH-2022010103).
文摘The present study designed two kinds of Fe-18Mn-1.3C-2Cr-(4,11)Al(wt.%)low-density steels.Tensile and impact tests were carried out to evaluate the work hardening and impact toughness properties via aluminum(Al)alloying control.Meanwhile,microstructure evolution and fracture morphology were investigated by X-ray diffraction(XRD),a scanning electron microscope(SEM)equipped with electron backscatter diffraction(EBSD),a transmission electron microscope(TEM),and a stereo-optical microscope(OM).It is found that the Al addition obviously promotes the dislocation planar slipping,resulting in cleavage and brittle impact fracture in 11wt.%Al steel.Besides,the microband-induced plasticity(MBIP)mechanism is found in 4wt.%Al containing steel,introducing considerable work hardening capacity and impact toughness of 156.8±17.4 J.The present study provides a direct illustration of the relationship between work hardening and impact toughness behaviors of these two low-density steels for potential application as impact-resistant components.
基金Item Sponsored by Early-Term Key Technology of Industrialization and Whole Set Equipment From Plan Committee of China(1999317) ,863 Project of China (2002AA331180) ,and Project of Key Lab of Universities in Jiangsu Province of China(Kjsmcx04004)
文摘The effect of main alloying elements on thermal wear of cast hot-forging die steels was studied. The wear mechanism was discussed. The results show that alloying elements have significant influences on the thermal wear of cast hot-forging die steels. The wear rates decrease with an increase in chromium content from 3% to 4% and molybdenum content from 2% to 3%, respectively. With further increase of chromium and molybdenum contents, chromium slightly reduces the wear resistance and molybdenum severely deteriorates the wear resistance with high wear rate. Lower vanadium/carbon ratio (1.5-2.5) leads to a lower wear resistance with higher wear rate. With an increase in vanadium/carbon ratio, the wear resistance of the cast steel substantially increases. When vanadium/carbon ratio is 3, the wear rate reaches the lowest value. The predominant mechanism of thermal wear of cast hot-forging die steels are oxidation wear and fatigue delamination. The Fe2O3 and Fe3O4 or lumps of brittle wear debris are formed on the wear surface.
文摘The influence of microalloying additions on the mechanical properties of a low-carbon cast steel containing combinations of V, Nb, and Ti in the as-cast condition was evaluated. Tensile and hardness test results indicated that good combinations of strength and ductility could be achieved by V and Nb additions. While the yield strength and UTS (ultimate tensile strength) increased up to the range of 378-435 MPa and 579- 590 MPa, respectively in the microalloyed heats, their total elongation ranged from 18% to 23%. The presence of Ti, however, led to some reduction in the strength. Microstructural studies including scanning electron microscopy (SEM) and optical microscopy revealed that coarse TiN particles were responsible for this behavior. The Charpy impact values of all compositions indicated that microalloying additions significantly decreased the impact energy and led to the dominance of cleavage facets on the fracture surfaces. It seems that the increase in the hardness of coarse ferrite grains due to the precipitation hardening is the main reason for brittle fracture.
基金Project supported by the Innovation Fund for Outstanding Scholar of Henan Province (0621000600)
文摘The toughness of 31Mn2SiRE wear-resistance cast steel were increased by means of RE compound modification and high temperature austenitizing. The results show that the microstructures can be refined, needle and network ferrite are eliminated, the dislocation density and the quantity of dislocated martensite are increased remarkably, and the shape and distribution of inclusions are improved by the addition of RE. Therefore, the mechanical properties of the modified steel can be greatly increased, especially the toughness (αK) by 44%, yield strength (σs) by 10%, and elongation (δ5) by 42%.
基金Project supported by the Itemof Early-TermKey Technology of Industrialization ,Plan Committee of China (1999317) 863project of China (2002AA331180)
文摘Thermal wear of cast hot-forging die steel modified by rare earths(RE) was studied and compared with commercially used die steels. The function of RE and the mechanism of thermal wear of cast steel modified by RE were discussed. The results showed that with increasing content of RE, the wear rate of cast steel reduced at first and then increased. By adding 0.05% (mass fraction) RE, the cast hot-forging die steel with optimum thermal wear resistance was obtained, which was better than that of H13 and 3Cr2WSV. The large amount of coarse inclusions, (RE)2O2S, resulted from excessive RE, which obviously deteriorated thermal wear resistance. The mechanism of thermal wear of the modified cast die steel is oxidation wear and oxide fatigue delamination. The wear debris are lumps of Fe2O3 and Fe3O4.
基金This work was financially supported by the National Basic Research on New Generation Steel (973) (No.J1998061511-3)
文摘With the help of solidification kinetics, precipitation and growth of TiNhave been studied theoretically and the effect of cooling rate on the growth of TiN has beendiscussed. Through induction electric furnace experiment and electroslag remelting experiment withdifferent cooling rates, the distribution and particle size of TiN were investigated. It is provedthat the higher cooling rate is, the smaller the final size of TiN is and the more TiN particles canbe found in the steel. That TiN can restrain the growth of columnar crystal and enhance theproportion of equiaxed crystals to refine solidification structure as the heterogeneous nucleationsites of δ-ferrite is confirmed preliminarily. A new method to reduce macrosegregation incontinuous cast steel is provided.
基金Item Sponsored by Guiding Programme of Science and Technology Research of Hebei of China(94122123)
文摘In isothermal spheroidizing process,the spheroidization and growth of the carbide formed in hot-deformed high-carbon chromium cast steel at high temperature were investigated.The results showed that the spheroidizing growth of carbide proceeds in such a way that the bigger carbide particles swallow the smaller ones,and the short rhabdoid carbides dissolve and are spheroidized by itself.When the samples were held at 720℃ for more than 3 h,the spheroidization is not obvious.The feature of the process is the size increment and the amount decrement of carbide particles.The empirical equation for growth rate of carbides was obtained.The volume fraction of carbides keeps constant.The growth process agrees well with Ostwald Ripening Law.
基金Item Sponsored by Guiding Program of Science and Technology Research of Hebei Province of China(94122123)
文摘The microstructure and properties of high carbonic-chromium cast steel subjected to different hot deformation ratios were studied.The experimental results show that the microstructure and properties of high carbonic-chromium cast steel are obviously improved after hot deformation,and the best mechanical properties of the cast steel can be obtained under hot deformation ratio of 40 %-50 %,which leads to the morphology change of eutectic carbide and the precipitation of granular carbides.
文摘The dendrite segregation in cast H13 steel was weakened with RE modification treatment. Grain boundary carbide during quenching was also under control and impact toughness was improved greatly. By thermodynamic calculation, analysis of two-dimensional lattice misfitting and electron probe analysis, it is found that Ce2O3 may act as the heterogeneous nuclei of modified cast H13 steel.
文摘A new type of Nb-V-Ti microalloyed cast steel was produced. Computer simulation was adopted to optimize the content of alloying elements. The microstructure of the microalloyed steel was analyzed. The fatigue property, wear and friction properties and rupture toughness of the steel were investigated. The service and operating properties of Nb-V-Ti microalloyed cast steel coupler were also examined. The results show that the steel has excellent comprehensive mechanical properties. The granular bainite structure and precipitation strengthening are the primary strengthening mechanism. The fine grain brings the steel good plasticity and excellent toughness. Various service and operating properties of Nb-V-Ti microalloyed cast steel automatic coupler are excellent.
基金Supported by the National Natural Science Foundation of China(No.51178307 and No.51525803)
文摘Due to traffic and wave actions, cast steel joints are subjected to variable-amplitude fatigue loading, which may cause fatigue problems. The ratio of the minimum strain to the maximum strain(strain ratio)can be employed to analyze the influence of variable-amplitude fatigue both in the elastic and plastic ranges. To evaluate the effect of the strain ratio on G20Mn5 QT cast steel, the fatigue tests of smooth specimens were carried out at the strain ratio of 0.1. The cyclic deformation and the relationships between the strain amplitude, the stress amplitude, the Smith, Watson and Topper(SWT)parameter and fatigue life were studied and compared with those at the strain ratio of-1. Compared with other methods, Basquin formula and Solonberg formula provide reliable and appropriate ranges of S-N curve and fatigue limit at different strain ratios respectively. The SWT parameter can be used to predict the fatigue life at other strain ratios accurately.
文摘The effects of RE modification on structure and the properties of a new cast hot work die (CHD) steel were investigated. The grains of the CHD steel are refined by RE modification. With the increase of RE addition, both grain size and inclusion amount are reduced. Appropriate amount of RE results in decrease in inclusion amount and formation of spheroidal inclusions uniformly-distributed in steel, so that the morphology and distribution of inclusions are improved. RE composite modification favors the formation of bainite, austenite and fine lath martensite with dense dislocation. When the residual RE content reaches 0.02%, no obvious changes in strength and hardness are found, while fracture toughness and threshold of fatigue crack growth are increased. The impact toughness, elongation and reduction of cross sectional area are increased by a factor of two, and thermal fatigue resistance is also improved.
文摘The effect of rare earth (Re) and titanium (Ti) multi-modification on the impact wear behavior of Mn-B high-Si bainitic cast steel was investigated systematically. The experiments show that the impact wear resistance can be improved greatly with the addition of Re and Ti. Its wear loss is only about 1/3-1/2 as large as that of the unmodified bainitic cast steel. By the Re/Ti modification, coarse dendrite grains and bainitic/martensite duplex structure have been refined effectively, and the impact toughness of the bainitic cast steel is nearly tripled (10 mm×10 mm×55 mm, with unnotched sample). Consequently, the modified bainitic cast steel possesses good wear resistance under high im- pact. For both modified and unmodified bainitic cast steels, high hardness white layer and deformed zone are developed beneath the worn surface under the high impact wear, but the formation and propagation of cracks are different for these bainitic casting steels. Different mod- els for the formation and propagation of cracks for both modified and unmodified bainitic cast steels under high impact wear are proposed.
文摘The effects of Si content on combinations of important properties such as hardness, hardenability, and weldability in addition to strength increment were systematically investigated to develop a Mo and V free low alloy cast steel for automobile cold pressing die insert. For the evaluation of the applicability as the die insert, the mechanical properties were measured after spheroidization annealing (SA), quenching and tempering (Q/T), and flame hardening (FH) treatments, respectively. The developed 0.8%-1.6%Si containing Mo and V free alloy cast steels showed excellent matrix strengthening effect, hardenability, and weldability, fulfilling the industrial criterion of the mechanical properties for the die insert.
基金Sponsored by the National Natural Science Foundation of China( Grant No. 50878066)the National Key Technology R&D Program during the 11th Five-Year Plan Period of China( Grant No. 2006BAJ01B02)
文摘This paper presents the shear performance analysis of a heavy-duty universal hinged cast steel support with the largest bearing capacity. The effect of 9 parameters ( 52 specimens) ,i. e. height of the upper support,depth of the ring of the upper support,depth of the top plate of the bottom support,height of the ribs of the bottom support,depth of the ribs of the bottom support,bolt hole diameter,number of the ribs of the bowl,depth of the ribs of the bowl,and yield strength of the material,were analyzed with a 3-dimensional elastic-plastic finite element model in which the nonlinearities of geometry,material and contact were all considered. Analysis shows that height of the upper support,depth of the ring of the upper support and yield strength of the material have a great effect on the mechanical performance of the support. Height of the upper support has the largest effect on performance price ratio of the support,and the maximum effect can be up to 160% . Depth of the top plate of the bottom support,height of the ribs of the bottom support and depth of the ribs of the bottom support have a medium effect on performance price ratio of the support,and the effect is within the limit of 15% 19% .
基金Supported by Key Program of National Natural Science Foundation of China(Grant No.51135007)National Natural Science Foundation of China(Grant Nos.51575371,61301250)Program for the Outstanding Innovative Teams of Higher Learning Institutions of Shanxi Province of China(Grant No.[2015]3)
文摘The dynamic recrystallization(DRX) simulation performance largely depends on simulated grain topological struc?tures. However, currently solutions used di erent models for describing two?dimensional(2 D) and three?dimensional(3 D) grain size distributions. Therefore, it is necessary to develop a more universal simulation technique. A cellular automaton(CA) model combined with an optimized topology deformation technology is proposed to simulate the microstructural evolution of 42 CrMo cast steel during DRX. In order to obtain values of material constants adopted in the CA model, hot deformation characteristics of 42 CrMo cast steel are investigated by hot compression metal?lographic testing. The proposed CA model deviates in two important aspects from the regular CA model. First, an optimized grain topology deformation technology is utilized for studying the hot compression e ect on the topology of grain deformation. Second, the overlapping grain topological structures are optimized by using an independent component analysis method, and the influence of various thermomechanical parameters on the nucleation process, grain growth kinetics, and mean grain sizes observed during DRX are explored. Experimental study shows that the average relative root mean square error(RRMSE) of the mean grain diameter obtained by the regular CA model is equal to 0.173, while the magnitude calculated using the proposed optimized CA model is only 0.11. This paper pro?poses a novel combined CA model for simulating the microstructural evolution of 42 CrMo cast steel, which notably uses a ICA?based grain topology deformation method to optimize the overlapping grain topological structures in simulation.
文摘The intergranular cracking of 9% Ni cast steel seems mainly to relate to the segregation of contaminates H,S and P along boundaries.An addition of rare earth may eliminate the seg- regation of these contaminates along grain boundaries and improve the binding force among boundaries,so as to reduce remarkably the intergranular cracking.
文摘The step pattern of single crystal growth and the morphology at equilibrium state of(Mn, Fe)S on the wall of micro-voids in ZG25 cast steel have been observed using scanning electron microscope.The face-centred cubic(Mn,Fe)S single crystal at equilibrium state is shown to be tetrakaidecahedron consisted of eight{111}planes and six{100}planes,and is a typical example of the O_h—m3m cubic crystal system.
基金finacially supported by the University Research Program between Ford Motor Company and the University of Science and Technology Beijing,and the Fundamental Research Funds for the Central Universities(Nos.FRF-IC-16-005 and FRF-IC-19-009)。
文摘The oxidation behaviors of three austenitic cast steels with different morphologies of primary carbides at 950℃ in air were investigated using scanning electron microscopy,energy dispersive spectroscopy,and focused ion beam/transmission electron microscopy.Their oxidation kinetics followed a logarithmic law,and the oxidation rate can be significantly decreased as long as a continuous silica layer formed at the scale/substrate interface.When the local Si concentration was inadequate,internal oxidation occurred beneath the oxide scale.The spallation of oxides during cooling can be inhibited with the formation of internal oxidation,owing to the reduced mismatch stress between the oxide scale and the substrate.The“Chinese-script”primary Nb(C,N)was superior to the dispersed primary Nb(C,N)in suppressing the oxidation penetration in the interdendritic region by supplying a high density of quick-diffusion Cr channels.In addition,the innermost and outermost oxidation layers were enriched with Cr,whereas the Cr evaporation in the outermost layer was significant when the water vapor concentration in the environment was high enough.These findings further the understanding regarding the oxidation behavior of austenitic cast steels and will promote the alloy development for exhaust components.