To develop the Q960 high-strength quenched and tempered steel plates for construction machinery,the effects of quenching and tempering treating regime on the microstructures and mechanical properties were investigated...To develop the Q960 high-strength quenched and tempered steel plates for construction machinery,the effects of quenching and tempering treating regime on the microstructures and mechanical properties were investigated.The results show that the perfect austenization and fine grain size can be achieved by the optimum quenching process that is quenching temperature 900℃ and holding time 20min.Considering performance and production efficiency,the optimum tempering process parameters are found that tempering temperature 600℃ and holding time 40min.The excellent overall properties of specimens with tempered sorbite microstructure can be ultimately obtained.The yield strength is 1030MPa,tensile strength 1080MPa,percentage elongation 16.8% and the Charpy impact energy 144J at-40℃.All these indexes come up to the National Standard GB/T 16270-2009.展开更多
Cold-rolled martensitic steel is an important type of advanced high-strength steel for automobile production.With martensite as its primary microstructure constituent, martensitic steel possesses exceptional high stre...Cold-rolled martensitic steel is an important type of advanced high-strength steel for automobile production.With martensite as its primary microstructure constituent, martensitic steel possesses exceptional high strength despite its low alloy content.As the strength of cold-rolled martensitic steel increases, the martensite and carbon content also increases, leading to a decrease in bending properties and toughness.In this paper, the effect of various tempering parameters on the bending property and impact toughness of a quenched cold-rolled martensitic steel sheet was studied.It is found that after quenching, the ductility and impact toughness of the experimental steel are improved using low-temperature heat treatment.The optimal tempering conditions for ductility and toughness are analyzed.展开更多
Conventional fusion arc welding of high-strength quenched and tempered steel can be improved through the use of non-conventional laser beam welding. This article presents the investigations of autogenous bead on plate...Conventional fusion arc welding of high-strength quenched and tempered steel can be improved through the use of non-conventional laser beam welding. This article presents the investigations of autogenous bead on plate and butt CO<sub>2</sub> Laser Welding (LW) of 7 mm thick high-strength quenched and tempered low alloy SM570 (JIS) steel plates. The influence of laser welding parameters, mainly welding speed, defocusing distance and shielding gas flow rate on the weld profile, i.e., weld zone penetration depth and width, microstructure and mechanical properties of welded joints was determined. All welded joints showed smooth and uniform weld beads free from superficial porosity and undercuts. The selected best welding conditions were a laser power of 5.0 kW, welding speed of 500 mm/min, argon gas shielding flow rate of 30 L/min and a defocusing distance of -0.5 mm. It was observed that these conditions gave complete penetration and minimized the width of the weld bead. The microstructure of the welded joints was evaluated by light optical microscopy. The weld metal (WM) and heat-affected zone (HAZ) near weld metal achieved maximum hardness (355 HV). The tensile fractured samples showed the ductile mode of failure and ultimate tensile strength of 580 MPa.展开更多
Using the Gleeble 3500 thermal-mechanical system to simulate thermal cycles with different peak temperatures, the hardness and microstructure in the heat-affected zones of two kinds of 100 kg class hot-rolled extra-hi...Using the Gleeble 3500 thermal-mechanical system to simulate thermal cycles with different peak temperatures, the hardness and microstructure in the heat-affected zones of two kinds of 100 kg class hot-rolled extra-high-strength steel were compared. When the peak temperature of the thermal cycle was 800℃ ,incomplete transformation occurred during quenching in both steels, and massive martensite and bainite grains were formed. The hardness was determined by the composition and distribution of the microstructure. The concentration of massive martensite was low, and hence the hardness was low,in steel #1. Conversely,the massive martensite content in steel #2 was high and uniformly distributed,resulting in a high hardness. These findings can provide a reference for improving the mechanical properties in the softened zone.展开更多
Because of the excellent mechanical properties of 34 CrNiMo6 steel, it is widely used in high-value components. Many conventional approaches to strengthening-steels typically involve the loss of useful ductility.In th...Because of the excellent mechanical properties of 34 CrNiMo6 steel, it is widely used in high-value components. Many conventional approaches to strengthening-steels typically involve the loss of useful ductility.In this study, 34 CrNiMo6 Steel having high strength and ductility is produced by laser solid forming(LSF)with a quenching-tempering(QT) treatment. Tempering of bainite is mainly by solid phase transformation in the previous LSF layers during the LSF process. The stable microstructure of LSF consists of ferrite and fine carbides. The microstructure transfers to tempered sorbite after heat-treatment. The tensile properties of the LSF steel meet those of the wrought standard. The UTS and elongation of LSF sample at 858 MPa, 19.2%, respectively, are greater than those of the wrought. The QT treatment enhanced the ultimate tensile strength and yield strength of the LSF sample. The ultimate tensile strength, yield strength, reduction in area, and elongation of the LSF+QT sample at 980 MPa, 916 MPa, 58.9%, and 13.9%,respectively, are greater than those of the wrought standard. The yield strength of the LSF+QT sample is approximately 1.27 times that of the wrought. The LSF samples failed in a ductile fracture mode, while the LSF+QT samples showed mixed-mode failure. The defects have only a small effect on the tensile properties owing to the excellent ductility of the LSF sample.展开更多
文摘To develop the Q960 high-strength quenched and tempered steel plates for construction machinery,the effects of quenching and tempering treating regime on the microstructures and mechanical properties were investigated.The results show that the perfect austenization and fine grain size can be achieved by the optimum quenching process that is quenching temperature 900℃ and holding time 20min.Considering performance and production efficiency,the optimum tempering process parameters are found that tempering temperature 600℃ and holding time 40min.The excellent overall properties of specimens with tempered sorbite microstructure can be ultimately obtained.The yield strength is 1030MPa,tensile strength 1080MPa,percentage elongation 16.8% and the Charpy impact energy 144J at-40℃.All these indexes come up to the National Standard GB/T 16270-2009.
文摘Cold-rolled martensitic steel is an important type of advanced high-strength steel for automobile production.With martensite as its primary microstructure constituent, martensitic steel possesses exceptional high strength despite its low alloy content.As the strength of cold-rolled martensitic steel increases, the martensite and carbon content also increases, leading to a decrease in bending properties and toughness.In this paper, the effect of various tempering parameters on the bending property and impact toughness of a quenched cold-rolled martensitic steel sheet was studied.It is found that after quenching, the ductility and impact toughness of the experimental steel are improved using low-temperature heat treatment.The optimal tempering conditions for ductility and toughness are analyzed.
文摘Conventional fusion arc welding of high-strength quenched and tempered steel can be improved through the use of non-conventional laser beam welding. This article presents the investigations of autogenous bead on plate and butt CO<sub>2</sub> Laser Welding (LW) of 7 mm thick high-strength quenched and tempered low alloy SM570 (JIS) steel plates. The influence of laser welding parameters, mainly welding speed, defocusing distance and shielding gas flow rate on the weld profile, i.e., weld zone penetration depth and width, microstructure and mechanical properties of welded joints was determined. All welded joints showed smooth and uniform weld beads free from superficial porosity and undercuts. The selected best welding conditions were a laser power of 5.0 kW, welding speed of 500 mm/min, argon gas shielding flow rate of 30 L/min and a defocusing distance of -0.5 mm. It was observed that these conditions gave complete penetration and minimized the width of the weld bead. The microstructure of the welded joints was evaluated by light optical microscopy. The weld metal (WM) and heat-affected zone (HAZ) near weld metal achieved maximum hardness (355 HV). The tensile fractured samples showed the ductile mode of failure and ultimate tensile strength of 580 MPa.
文摘Using the Gleeble 3500 thermal-mechanical system to simulate thermal cycles with different peak temperatures, the hardness and microstructure in the heat-affected zones of two kinds of 100 kg class hot-rolled extra-high-strength steel were compared. When the peak temperature of the thermal cycle was 800℃ ,incomplete transformation occurred during quenching in both steels, and massive martensite and bainite grains were formed. The hardness was determined by the composition and distribution of the microstructure. The concentration of massive martensite was low, and hence the hardness was low,in steel #1. Conversely,the massive martensite content in steel #2 was high and uniformly distributed,resulting in a high hardness. These findings can provide a reference for improving the mechanical properties in the softened zone.
基金supported by National Natural Science Foundation of China (Grant Nos. 51565041, 51465044 and 51323008)the National Key Research and Development Program of China (No. 2016YFB1100100)the fund of the State Key Laboratory of Solidification Processing in NWPU (No. SKLSP201634)
文摘Because of the excellent mechanical properties of 34 CrNiMo6 steel, it is widely used in high-value components. Many conventional approaches to strengthening-steels typically involve the loss of useful ductility.In this study, 34 CrNiMo6 Steel having high strength and ductility is produced by laser solid forming(LSF)with a quenching-tempering(QT) treatment. Tempering of bainite is mainly by solid phase transformation in the previous LSF layers during the LSF process. The stable microstructure of LSF consists of ferrite and fine carbides. The microstructure transfers to tempered sorbite after heat-treatment. The tensile properties of the LSF steel meet those of the wrought standard. The UTS and elongation of LSF sample at 858 MPa, 19.2%, respectively, are greater than those of the wrought. The QT treatment enhanced the ultimate tensile strength and yield strength of the LSF sample. The ultimate tensile strength, yield strength, reduction in area, and elongation of the LSF+QT sample at 980 MPa, 916 MPa, 58.9%, and 13.9%,respectively, are greater than those of the wrought standard. The yield strength of the LSF+QT sample is approximately 1.27 times that of the wrought. The LSF samples failed in a ductile fracture mode, while the LSF+QT samples showed mixed-mode failure. The defects have only a small effect on the tensile properties owing to the excellent ductility of the LSF sample.