3D MERGE与3D SPACE STIR序列在腰椎间盘突出症检查中的应用比较

目的:对比三维多回波恢复梯度回波(3D MERGE)、三维可变反转角快速自旋回波(3D SPACE STIR)序列在腰椎间盘突出症(LDH)检查中的应用效果。方法:选择2020年1月~2022年11月收治的135例LDH患者,回顾性分析患者临床和磁共振成像(MRI)资料,所有患者均接受常规MRI扫描及3D MERGE、3D SPACE STIR序列扫描,对比3D MERGE、3D SPACE STIR序列测量神经根直径的一致性,评价两种序列的图像质量参数[信噪比(SNR)、对比噪声比(CNR)]、图像清晰度评分。结果:3D MERGE和3D SPACE STIR序列测量的L3~S1神经根直径比较差异无统计学意义(P>0.05),且两组序列测量的L3、L4、L5和S1直径均显示出较高相关性(r=0.957,0.986,0.975,0.972,P<0.05);3D MERGE序列的SNR及CNR均高于3D SPACE STIR序列,神经根显示分级、图像清晰度评分优于3D SPACE STIR序列,差异有统计学意义(P<0.05)。结论:3D MERGE、3D SPACE STIR序列在LDH神经根直径测量中具有极高一致性,3D MERGE序列较3D SPACE STIR序列能够更清晰显示神经跟的解剖形态,图像质量更好。

Effect of Butternut Squash (Cucurbita moschata) Seed Powder on the Chemical and Rheological Properties of Stirred Cultured Camel Milk and Yoghurt

Research shows that producing fermented camel milk is hard because of the milk’s inability to form a firm coagulum, attributed to low levels of κ-casein and ꞵ-lactoglobulin and the large casein micelle size, leading to a weak network of casein formation. In an effort to address this issue, researchers turned to corn starch as a thickening agent, discovering that a concentration of 2.0% effectively improved the viscosity and significantly reduced syneresis in stirred camel milk yoghurt and cultured camel milk. This study explores alternatives to corn starch, focusing on butternut squash seeds as a promising substitute due to their hydrocolloid composition. By incorporating butternut squash (Cucurbita moschata) seed powder (BSSP) as a thickening agent, this study aimed at enhancing the chemical and rheological properties of stirred camel milk yoghurt and cultured camel milk. Fermented camel milk was prepared using 4 litres of camel milk, 2% starter cultures (thermophilic culture for yoghurt and mesophilic aromatic culture for stirred cultured camel milk) and BSSP 0.0% (negative control), 0.4%, 0.8%, 1.2%, 1.6%, 2.0% mixed with 0.4% gelatin. 2.0% corn starch mixed with 0.4% gelatin was used as a standard for comparison. Results showed that increasing the BSSP level significantly (p < 0.05) decreased the moisture content while increasing the total solid content of stirred fermented camel milk products. There was an increase in ash content with an increase in BSSP levels. There was a significant (p < 0.05) reduction in the pH, with an increase in BSSP levels in stirred fermented camel milk samples. Increasing the concentration of BSSP from 0.4% to 2.0% resulted in a significant (p < 0.05) increase in viscosity and a reduction in syneresis of stirred camel milk yoghurt and stirred cultured camel milk samples. This study demonstrated that BSSP effectively enhances the viscosity, reduces syneresis and increases acidity in stirred fermented camel milk products during storage.

STIR联合FLAIR对视神经炎临床诊断的作用分析

目的:探讨短时间反转恢复序列(Short Time of Inversion Recovery,STIR)联合液体衰减反转恢复序列(Fluid-attenuated inversion recovery,FLAIR)对视神经炎(Optic neuritis,ON)临床诊断作用.方法:回顾性分析2018年1月至2022年12月间我院收治的82例确诊为ON且均为单眼受累的患者的临床资料.所有患者均接受磁共振扫描,包括冠状面STIR、STIR-FLAIR以及T1WI序列.记录STIR、STIR-FLAIR视神经炎检出率、病变部位检出情况以及标准信号强度(Standard signal strength,Sn)、病变信号强度/同侧眼眶内脂肪信号强度(Signal intensity of ON lesions/ipsilateral orbital fat signal,SON/SIfat)、病变信号强度/对侧视神经信号强度(Signal intensity of ON lesions/contralateral optic nerve signal intensity,SON/SCON)指标.结果:STIR-FLAIR序列检出率高于STIR序列(P<0.05);STIR序列病变部位分为眶内段30个、管内段19个、眶内和管内段22个、眶内-管内-颅内6个;STIR-FLAIR序列病变部位分为眶内段32个、管内段20个、眶内和管内段23个、眶内-管内-颅内7个,两组序列病变部位检出数据差值无意义;STIR-FLAIR序列的Sn、SON/SIfat、SON/SCON均高于STIR序列(P<0.05).结论:相较STIR序列而言,STIR-FLAIR序列对脂肪信号、水序号的抑制优势明显,可以提高ON的临床诊断可靠性,值得推广.

MR3D-STIR SPACE序列增强扫描在臂丛节后神经成像的效果分析

目的探讨在臂丛节后神经成像中施行MR3D-STIR SPACE序列增强扫描的临床价值及成像质量。方法选取50例、2021年1月-2022年8月臂丛神经患者,均行MR常规序列扫描、MR3D-SPACE-STIR序列平扫及增强扫描。对患者的损伤部位、形态、信号强度与近、远侧段臂丛神经的相关性,并对比平扫及增强图像质量。结果MRI平扫诊断节后神经损伤敏感性为89.47%、特异性为83.33%、准确性88.64%。增强MR3D-SPACE-STIR的组织对比显著提高,经处理后,可对臂丛神经节后的走行图像进行完整显示。且该技术增强序列图像的对比噪声比(CNR)为(0.57±0.09)、背景抑制评分(3.56±0.63)分及对臂丛神经显示评分(3.96±0.53)与平扫(0.35±0.06)、(1.58±0.51)分、(2.02±0.59)分均存在显著差异(t=12.231,12.214,10.170;P<0.05)。结论MR 3D-SPACE-STIR序列增强扫描的背景抑制效果较佳,可使臂丛神经损伤及走形得以清晰显示,其臂丛神经节后图像质量较平扫明显提升。

Effect of aspect ratio of elliptical stirred vessel on mixing time and flow field characteristics in the absence of baffles

Elliptical tanks were used as an alternative to circular tanks in order to improve mixing efficiency and reduce mixing time in unbaffled stirred tanks(USTs). Five different aspect ratios of elliptical vessels were designed to compare their mixing time and flow field. Computational fluid dynamics(CFD) simulations were performed using the k–ε model to calculate the mixing time and simulate turbulent flow field features, such as streamline shape, velocity distribution, vortex core region distribution, and turbulent kinetic energy(TKE) transfer. Visualization was also carried out to track the tinctorial evolution of the liquid phase. Results reveal that elliptical stirred tanks can significantly improve mixing performance in USTs. Specifically, the mixing time at an aspect ratio of 2.00 is only 45.3% of the one of a circular stirred tank. Furthermore, the secondary flow is strengthened and the vortex core region increases with the increase of aspect ratio. The axial velocity is more sensitive to the aspect ratio than the circumferential and radial velocity. Additionally, the TKE transfer in elliptical vessels is altered. These findings suggest that elliptical vessels offer a promising alternative to circular vessels for enhancing mixing performance in USTs.

Improvement of Microstructure and Mechanical Properties of Rapid Cooling Friction Stir-welded A1050 Pure Aluminum

Two-mm thick A1050 pure aluminum plates were successfully joined by conventional and rapid cooling friction stir welding(FSW), respectively. The microstructure and mechanical properties of the welded joints were investigated by electron backscatter diffraction characterization, Vickers hardness measurements, and tensile testing. The results showed that liquid CO_(2) coolant significantly reduced the peak temperature and increased the cooling rate, so the rapidly cooled FSW joint exhibited fine grains with a large number of dislocations. The grain refinement mechanism of the FSW A1050 pure aluminum joint was primarily attributed to the combined effects of continuous dynamic recrystallization, grain subdivision, and geometric dynamic recrystallization. Compared with conventional FSW, the yield strength, ultimate tensile strength, and fracture elongation of rapidly cooled FSW joint were significantly enhanced, and the welding efficiency was increased from 80% to 93%. The enhanced mechanical properties and improved synergy of strength and ductility were obtained due to the increased dislocation density and remarkable grain refinement. The wear of the tool can produce several WC particles retained in the joint, and the contribution of second phase strengthening to the enhanced strength should not be ignored.

Multi-physical fields distribution in billet during helical electromagnetic stirring:A numerical simulation research

Electromagnetic stirring is one of the widely applied techniques to modify the quality of casting billets.Different from conventional rotate stirring,the helical stirring is more professional in assisting multi-dimensional flow of molten metal and eliminating solidification defects.In this study,the single-winding helical stirring(SWHS)was introduced,offering advantages such as smaller volume and lower electromagnetic shielding compared to traditional helical stirring methods.Following a comprehensive numerical simulation,the stirring parameters of SWHS were adjusted to yoke inclination angle of 43°and frequency of 12 Hz.The higher electromagnetic force and flow velocity in drawing direction,as well as the lower temperature gradient induced by the SWHS,are positive factors for homogeneous solidification of billet.The experimental results on Al-8%Si alloy and 0.4%C-1.1%Mn steel demonstrate that compared to rotate stirring,the SWHS process can induce better billet quality and is more effective in accelerating the equiaxed expansion and reducing element segregation.The SWHS process can enhance the equiaxed ratio of the billet by 58.3%and reduce segregation degree of carbon element by 10.97%.Consequently,SWHS holds great promise as a potential approach for improving the quality of continuous casting billets.

Effects of friction stir processing and nano-hydroxyapatite on the microstructure,hardness,degradation rate and in-vitro bioactivity of WE43 alloy for biomedical applications

Nowadays,magnesium alloys are emerging in biomedical implants for their similar properties to natural bones.However,the rapid degradation of magnesium alloys in biological media hinders successful implantation.Refinement of microstructure,as well as reinforcement particles can significantly improve the degradation rate.In this work,multi-pass friction stir processing(FSP)was proposed to synthesize WE43/nano-hydroxyapatite(n HA)surface composite,the microstructure,reinforced particle distribution,micro-hardness,corrosion behavior and in-vitro bioactivity were studied.The subsequent FSP passes of WE43 alloy and WE43/n HA composite refined the grain size which was reduced by 94.29%and 95.92%(2.63 and 1.88μm,respectively)compared to base metal after three passes.This resulted in increasing the microhardness by 120%(90.86 HV0.1)and 135%(105.59 HV0.1)for the WE43 and WE43-n HA,respectively.It is found that increasing FSP passes improved the uniform distribution of n HA particles within the composite matrix which led to improved corrosion resistance and less degradation rate.The corrosion rate of the FSPed WE43/n HA composite after three passes was reduced by 38.2%(4.13 mm/year)and the degradation rate was reduced by 69.7%(2.87 mm/y).This is attributed to secondary phase(Mg24Y5and Mg41Nd5)particle fragmentation and redistribution,as well as a homogeneous distribution of n HA.Additionally,the growing Ca-P and Mg(OH)2layer formed on the surface represented a protective layer that reduced the degradation rate.The wettability test revealed a relatively hydrophilic surface with water contact angle of 49.1±2.2°compared to 71.2±2.1°for base metal.Also,biomineralization test showed that apatite layer grew after immersion 7d in simulated body fluid with atomic ratio of Ca/P 1.60 approaching the stoichiometric ratio(1.67)indicating superior bioactivity of FSPed WE43/n HA composite after three passes.These results raise that the grain refinement by FSP and introduction of n HA particles significantly improved the degradation rate and in-vitro bioactivity of WE43 alloy for biomedical applications.

Application of the CatBoost Model for Stirred Reactor State Monitoring Based on Vibration Signals

Stirred reactors are key equipment in production,and unpredictable failures will result in significant economic losses and safety issues.Therefore,it is necessary to monitor its health state.To achieve this goal,in this study,five states of the stirred reactor were firstly preset:normal,shaft bending,blade eccentricity,bearing wear,and bolt looseness.Vibration signals along x,y and z axes were collected and analyzed in both the time domain and frequency domain.Secondly,93 statistical features were extracted and evaluated by ReliefF,Maximal Information Coefficient(MIC)and XGBoost.The above evaluation results were then fused by D-S evidence theory to extract the final 16 features that are most relevant to the state of the stirred reactor.Finally,the CatBoost algorithm was introduced to establish the stirred reactor health monitoring model.The validation results showed that the model achieves 100%accuracy in detecting the fault/normal state of the stirred reactor and 98%accuracy in diagnosing the type of fault.

Preheating-assisted solid-state friction stir repair of Al-Mg-Si alloy plate at different rotational speeds

Additive friction stir deposition(AFSD)is a novel structural repair and manufacturing technology has become a research hotspot at home and abroad in the past five years.In this work,the microstructural evolution and mechanical performance of the Al-Mg-Si alloy plate repaired by the preheating-assisted AFSD process were investigated.To evaluate the tool rotation speed and substrate preheating for repair quality,the AFSD technique was used to additively repair 5 mm depth blind holes on 6061 aluminum alloy substrates.The results showed that preheat-assisted AFSD repair significantly improved joint bonding and joint strength compared to the control non-preheat substrate condition.Moreover,increasing rotation speed was also beneficial to improve the metallurgical bonding of the interface and avoid volume defects.Under preheating conditions,the UTS and elongation were positively correlated with rotation speed.Under the process parameters of preheated substrate and tool rotation speed of 1000 r/min,defect-free specimens could be obtained accompanied by tensile fracture occurring in the substrate rather than the repaired zone.The UTS and elongation reached the maximum values of 164.2MPa and 13.4%,which are equivalent to 99.4%and 140%of the heated substrate,respectively.

Tailoring the microstructure of Mg-Al-Sn-RE alloy via friction stir processing and the impact on its electrochemical discharge behaviour as the anode for Mg-air battery

Constructing the magnesium alloy with fine grains,low density of dislocations,and weak crystal orientation is of crucial importance to enhance its comprehensive performance as the anode for Mg-air battery.However,this unique microstructure can hardly be achieved with conventional plastic deformation such as rolling or extrusion.Herein,we tailor the microstructure of Mg-Al-Sn-RE alloy by using the friction stir processing,which obviously refines the grains without increasing dislocation density or strengthening crystal orientation.The Mg-air battery with the processed Mg-Al-Sn-RE alloy as the anode exhibits higher discharge voltages and capacities than that employing the untreated anode.Furthermore,the impact of friction stir processing on the electrochemical discharge behaviour of Mg-Al-Sn-RE anode and the corresponding mechanism are also analysed according to microstructure characterization and electrochemical response.

Prediction of corrosion rate for friction stir processed WE43 alloy by combining PSO-based virtual sample generation and machine learning

The corrosion rate is a crucial factor that impacts the longevity of materials in different applications.After undergoing friction stir processing(FSP),the refined grain structure leads to a notable decrease in corrosion rate.However,a better understanding of the correlation between the FSP process parameters and the corrosion rate is still lacking.The current study used machine learning to establish the relationship between the corrosion rate and FSP process parameters(rotational speed,traverse speed,and shoulder diameter)for WE43 alloy.The Taguchi L27 design of experiments was used for the experimental analysis.In addition,synthetic data was generated using particle swarm optimization for virtual sample generation(VSG).The application of VSG has led to an increase in the prediction accuracy of machine learning models.A sensitivity analysis was performed using Shapley Additive Explanations to determine the key factors affecting the corrosion rate.The shoulder diameter had a significant impact in comparison to the traverse speed.A graphical user interface(GUI)has been created to predict the corrosion rate using the identified factors.This study focuses on the WE43 alloy,but its findings can also be used to predict the corrosion rate of other magnesium alloys.

Microstructure and mechanical properties of stationary shoulder friction stir welding joint of 2A14-T62 aluminum alloy

2A14-T62 butt joint was successfully welded by stationary shoulder friction stir welding(SSFSW)method.The results showed that using a pin with small shoulder could broaden the process window,and under a rotation speed of 2000 r/min and welding speed of 30 mm/min,joint with smooth surface,small reduction in thickness and little inner defects was obtained.The weld nugget zone was approx-imately circular,which was a unique morphology for SSFSW.The heat-affected zone(HAZ)and thermo-mechanically affected zone(TMAZ)were both quite narrow due to the lower heat input and slight mechanical action of the stationary shoulder.The fraction of high angle grain boundaries(HAGBs)exhibited a“W”shape along horizontal direction(from advancing side to retreating side),and the minim-um value located at HAZ.The average ultimate tensile strength and elongation of the joint were 325 MPa and 4.5%,respectively,with the joint efficiency of 68.3%.The joint was ductile fractured and the fracture surface contained two types of dimples morphology in different re-gions of the joint.Microhardness distribution in the joint exhibited a“W”shape,and the difference along the thickness direction was negli-gible.The joint had strong stress corrosion cracking susceptibility,and the slow stain rate tensile strength was 139 MPa.Microcrack and Al2O3 particulates were observed at the fracture surface.

Achieving a high-strength dissimilar joint of T91 heat-resistant steel to 316L stainless steel via friction stir welding

The reliable welding of T91 heat-resistant steel to 316L stainless steel is a considerable issue for ensuring the safety in service of ultrasupercritical power generation unit and nuclear fusion reactor,but the high-quality dissimilar joint of these two steels was difficult to be obtained by traditional fusion welding methods.Here we improved the structure-property synergy in a dissimilar joint of T91 steel to 316L steel via friction stir welding.A defect-free joint with a large bonding interface was produced using a small-sized tool under a relatively high welding speed.The bonding interface was involved in a mixing zone with both mechanical mixing and metallurgical bonding.No obvious material softening was detected in the joint except a negligible hardness decline of only HV~10 in the heat-affected zone of the T91 steel side due to the formation of ferrite phase.The welded joint exhibited an excellent ultimate tensile strength as high as that of the 316L parent metal and a greatly enhanced yield strength on account of the dependable bonding and material renovation in the weld zone.This work recommends a promising technique for producing high-strength weldments of dissimilar nuclear steels.

An innovative joint interface design for reducing intermetallic compounds and improving joint strength of thick plate friction stir welded Al/Mg joints

Friction stir welding of dissimilar Al/Mg thick plates still faces severe challenges, such as poor formability, formation of thick intermetallic compounds, and low joint strength. In this work, two joint configurations, namely inclined butt(conventional butt) and serrated interlocking(innovative butt), are proposed for improving weld formation and joint quality. The results show that a continuous and straight intermetallic compound layer appears at the Mg side interface in conventional butt joint, and the maximum average thickness reaches about 60.1 μm.Additionally, the Mg side interface also partially melts, forming a eutectic structure composed of Mg solid solution and Al_(12)Mg_(17) phase.For the innovative butt joint, the Mg side interface presents the curved interlocking feature, and intermetallic compounds can be reduced to less than 10 μm. The joint strength of innovative butt joint is more than three times that of conventional butt joint. This is due to the interlocking effect and thin intermetallic compounds in the innovative joint.

Mechanical properties and microstructural evolution of rheocast A356 semi-solid slurry prepared by annular electromagnetic stirring

Nowadays,having an effective technique in preparing semi-solid slurries for rheocasting process seems to be an essential requirement.In this study,semi-solid slurry of A356 aluminum alloy was prepared by three-phase annular electromagnetic stirring(A-EMS)technique under different conditions.The effects of stirring current,pouring temperature and stirring time on microstructural evolution,mean particle size,shape factor and solid fraction were investigated.The rheocasting process was carried out by using a drop weight setup and to inject the prepared semi-solid slurry in optimal conditions into the step-die cavity.The filling behavior and mechanical properties of parts were studied.Microstructural evolution showed that the best semi-solid slurry which had fine spherical particles with the average size of~27μm and a shape factor of~0.8 was achieved at the stirring current of 70 A,melt pouring temperature of 670℃,and stirring time of 30 s.Under these conditions,the step-die cavity was completely filled at die preheating temperature of 470℃.The hardness increases by decreasing step thickness as well as die preheating temperature.Moreover,the tensile properties are improved at lower die preheating temperatures.The fracture surface,which consists of a complex topography,indicates a typical ductile fracture.

Impact of Inulin Extracted, Purified from (Chicory and Globe Artichoke) Roots and the Combination with Maltodextrin as Prebiotic Dietary Fiber on the Functional Properties of Stirred Bio-Yogurt

Inulin is a prebiotic dietary fiber that plays an integral role in producing functional dairy products with improved health benefits. Therefore, the objectives of this study are as follows: extract and purify inulin from chicory roots and globe artichoke roots;evaluate the physicochemical, functional properties and functional groups of the purified inulin;determine the functional properties of chicory roots inulin-maltodextrin and globe artichoke roots inulin-maltodextrin and compare it with that of the commercial inulin;examine the impact of various inulin on physiochemical, microstructural, textural, sensory characteristics and as prebiotic dietary fiber on probiotic bacteria’s viability of stirred bio-yogurt. The characteristics of the microstructure were investigated by scanning electron microscopy and, Fourier transforms infrared spectroscopy to detect the functional group. The resulting inulin exhibited a high yield and purity along with enhanced functional properties. Stirred bio-yogurt fortified with chicory roots inulin or globe artichoke roots inulin showed enhanced physicochemical, microstructural, microbiological, and overall sensorial acceptability followed by chicory roots inulin-maltodextrin or globe artichoke roots inulin-maltodextrin and the commercial inulin as compared to the control. Stirred bio-yogurt samples can offer various health benefits and wide applications as supplement of prebiotic dietary fiber in dairy industry.

Research on friction stir welding of 5754 aluminum alloy with unequal thickness

A new structure of 1+2 was designed in friction stir welding(FSW)of Al alloy sheet with unequal thickness:a specific sheet with similar composition of base metals(BMs)was placed under the thinner sheet as the supporting sheet so that the BM surfaces could be on a plane.The BMs can also be fully penetrated weld with a stirring pin longer than the thickness of the thin sheet.2 mm and 1.5 mm thick Al alloy sheets were welded by FSW,and parameters were optimized.The highest welding strength reached 96.07%of the thin base metal.Although a slight thinning phenomenon occurred at the edge of the nugget on the retreating side,the specimen still fractured in the heat-af-fected zone.

STIR技术脊柱MRI诊断急性隐匿性椎体损伤的价值研究

目的:分析MRI短时反转恢复(STIR)序列诊断急性隐匿性椎体损伤的临床价值。方法:择取2019年1月至2020年12月本院急性脊柱创伤病人89例,进行自旋回波序列T1WI、快速自旋回波T2WI序列、STIR序列的MRI检查,分析病人隐匿性椎体损伤状况。结果:89例患者中,T2WI序列检出210节椎体异常高信号(正常形态124节,形态异常86节),STIR序列检出250节异常高信号(正常形态164节,形态异常86节),STIR序列较T2WI序列多检出40节(P<0.05)。89例病人中出现继发性不相邻损伤椎体节段146节,损伤部位以胸椎损伤最为常见(占38.36%),病因以骨挫伤为最常见(占36.99%)。结论:相较于T2WI,MRI STIR序列更为全面、准确地评估急性脊柱创伤后隐性椎体受损,对于无形态改变的椎体损伤更为敏感,可早期全面地评估继发性、多水平、不相邻椎体损伤,对指导治疗方案及评估预后方面具有重要意义。

Microstructure and toughness of thick-gauge pipeline steel joint via double-sided friction stir welding combined with preheating

Fusion welding easily causes microstructural coarsening in the heat-affected zone(HAZ) of a thick-gauge pipeline steel joint. This is most significant in the inter-critically coarse-grained HAZ(ICCGHAZ), which considerably deteriorates the toughness of the joint. In the present work, 11-mm thick pipeline steel was joined by preheating and double-sided friction stir welding(FSW). A comparative study on the microstructure and toughness in the ICCGHAZs for FSW and gas metal arc welding(GMAW) was performed. The toughness in the ICCGHAZ for FSW was improved significantly than that in the ICCGHAZ for GMAW. Generally, the nugget zone(NZ) has a coarse microstructure in the FSW steel joint formed at the highest peak temperature. However, in the current study, the microstructure in the one-pass NZ was remarkably refined owing to the static recrystallization of ferrite. An excellent toughness was achieved in the NZ of the pipeline steel joint that employed FSW.