Modeling of Large-Scale Hydrogen Storage System Considering Capacity Attenuation and Analysis of Its Efficiency Characteristics

In the existing power system with a large-scale hydrogen storage system,there are problems such as low efficiency of electric-hydrogen-electricity conversion and single modeling of the hydrogen storage system.In order to improve the hydrogen utilization rate of hydrogen storage system in the process of participating in the power grid operation,and speed up the process of electric-hydrogen-electricity conversion.This article provides a detailed introduction to the mathematical and electrical models of various components of the hydrogen storage unit,and also establishes a charging and discharging efficiency model that considers the temperature and internal gas partial pressure of the hydrogen storage unit.These models are of great significance for studying and optimizing gas storage technology.Through these models,the performance of gas storage units can be better understood and improved.These studies are very helpful for improving energy storage efficiency and sustainable development.The factors affecting the charge-discharge efficiency of hydrogen storage units are analyzed.By integrating the models of each unit and considering the capacity degradation of the hydrogen storage system,we can construct an efficiency model for a large hydrogen storage system and power conversion system.In addition,the simulation models of the hydrogen production system and hydrogen consumption system were established in MATLAB/Simulink.The accuracy and effectiveness of the simulation model were proved by comparing the output voltage variation curve of the simulation with the polarization curve of the typical hydrogen production system and hydrogen consumption system.The results show that the charge-discharge efficiency of the hydrogen storage unit increases with the increase of operating temperature,and H2 and O2 partial voltage have little influence on the charge-discharge efficiency.In the process of power conversion system converter rectification operation,its efficiency decreases with the increase of temperature,while in the process of inverter operation,power conversion system efficiency increases with the increase of temperature.Combined with the efficiency of each hydrogen storage unit and power conversion system converter,the upper limit of the capacity loss of different hydrogen storage units was set.The optimal charge-discharge efficiency of the hydrogen storage system was obtained by using the Cplex solver at 36.46%and 66.34%.

Research on Regulation Method of Energy Storage System Based on Multi-Stage Robust Optimization

To address the scheduling problem involving energy storage systems and uncertain energy,we propose a method based on multi-stage robust optimization.This approach aims to regulate the energy storage system by using a multi-stage robust optimal control method,which helps overcome the limitations of traditional methods in terms of time scale.The goal is to effectively utilize the energy storage power station system to address issues caused by unpredictable variations in environmental energy and fluctuating load throughout the day.To achieve this,a mathematical model is constructed to represent uncertain energy sources such as photovoltaic and wind power.The generalized Benders Decomposition method is then employed to solve the multi-stage objective optimization problem.By decomposing the problem into a series of sub-objectives,the system scale is effectively reduced,and the algorithm’s convergence ability is improved.Compared with other algorithms,the multi-stage robust optimization model has better economy and convergence ability and can be used to guide the power dispatching of uncertain energy and energy storage systems.

Energy Storage Systems Technologies, Evolution and Applications

Energy in its varied forms and applications has become the main driver of today’s modern society. However, recent changes in power demand and climatic changes (decarbonization policy) has awakened the need to rethink through the current energy generating and distribution system. This led to the exploration of other energy sources of which renewable energy (like thermal, solar and wind energy) is fast becoming an integral part of most energy system. However, this innovative and promising energy source is highly unreliable in maintaining a constant peak power that matches demand. Energy storage systems have thus been highlighted as a solution in managing such imbalances and maintaining the stability of supply. Energy storage technologies absorb and store energy, and release it on demand. This includes gravitational potential energy (pumped hydroelectric), chemical energy (batteries), kinetic energy (flywheels or compressed air), and energy in the form of electrical (capacitors) and magnetic fields. This paper provides a detailed and comprehensive overview of some of the state-of-the-art energy storage technologies, its evolution, classification, and comparison along with various area of applications. Also highlighted in this paper is a plethora of power electronic Interface technologies that plays a significant role in enabling optimum performance and utilization of energy storage systems in different areas of application.

Market Operation of Energy Storage System in Smart Grid:A Review

As a flexible resource,energy storage plays an increasingly significant role in stabilizing and supporting the power system,while providing auxiliary services.Still,the current high demand for energy storage contrasts with the fuzzy lack of market-oriented mechanisms for energy storage,the principle of market-oriented operation has not been embodied,and there is no unified and systematic analytical framework for the business model.However,the dispatch management model of energy storage in actual power system operation is not clear.Still,the specific scheduling process and energy storage strategy on the source-load-network side could be more specific,and there needs to be a greater understanding of the collaborative scheduling process of the multilevel scheduling center.On this basis,this paper reviews the energy storage operation model and market-based incentive mechanism,For different functional types and installation locations of energy storage within the power system,the operational models and existing policies for energy storage participation in the market that are adapted to multiple operating states are summarized.From the point of view of the actual scheduling and operation management of energy storage in China,an energy storage regulation and operation management model based on“national,provincial,and local”multilevel coordination is proposed,as well as key technologies in the interactive scenarios of source-load,network and storage.

Coordinated planning for flexible interconnection and energy storage system in low-voltage distribution networks to improve the accommodation capacity of photovoltaic

The increasing proportion of distributed photovoltaics(DPVs)and electric vehicle charging stations in low-voltage distribution networks(LVDNs)has resulted in challenges such as distribution transformer overloads and voltage violations.To address these problems,we propose a coordinated planning method for flexible interconnections and energy storage systems(ESSs)to improve the accommodation capacity of DPVs.First,the power-transfer characteristics of flexible interconnection and ESSs are analyzed.The equipment costs of the voltage source converters(VSCs)and ESSs are also analyzed comprehensively,considering the differences in installation and maintenance costs for different installation locations.Second,a bilevel programming model is established to minimize the annual comprehensive cost and yearly total PV curtailment capacity.Within this framework,the upper-level model optimizes the installation locations and capacities of the VSCs and ESSs,whereas the lower-level model optimizes the operating power of the VSCs and ESSs.The proposed model is solved using a non-dominated sorting genetic algorithm with an elite strategy(NSGA-II).The effectiveness of the proposed planning method is validated through an actual LVDN scenario,which demonstrates its advantages in enhancing PV accommodation capacity.In addition,the economic benefits of various planning schemes with different flexible interconnection topologies and different PV grid-connected forms are quantitatively analyzed,demonstrating the adaptability of the proposed coordinated planning method.

Reinforcement learning-based scheduling of multi-battery energy storage system

In this paper, a reinforcement learning-based multibattery energy storage system(MBESS) scheduling policy is proposed to minimize the consumers ’ electricity cost. The MBESS scheduling problem is modeled as a Markov decision process(MDP) with unknown transition probability. However, the optimal value function is time-dependent and difficult to obtain because of the periodicity of the electricity price and residential load. Therefore, a series of time-independent action-value functions are proposed to describe every period of a day. To approximate every action-value function, a corresponding critic network is established, which is cascaded with other critic networks according to the time sequence. Then, the continuous management strategy is obtained from the related action network. Moreover, a two-stage learning protocol including offline and online learning stages is provided for detailed implementation in real-time battery management. Numerical experimental examples are given to demonstrate the effectiveness of the developed algorithm.

Utilizing hybrid faradaic mechanism via catalytic and surface interactions for high-performance flexible energy storage system

Improving the capacitance and energy density is a significant challenge while developing practical and flexible energy storage system(ESS).Redox mediators(RMs),as redox-active electrolyte additives,can provide additional energy storing capability via electrochemical faradaic contribution on electrodes for high-performance flexible ESSs.Particularly,determining effective material combinations between electrodes and RMs is essential for maximizing surface faradaic redox reactions for energy-storage performance.In this study,an electrode-RM system comprising heterostructured hybrid(carbon fiber(CF)/MnO_(2)) faradaic electrodes and iodine RMs(I-RMs) in a redox-active electrolyte is investigated.The CF/MnO_(2)with the 1-RMs(CF/MnO_(2)-I) induces dominant catalytic faradaic interaction with the I-RMs,significantly enhancing the surface faradaic kinetics and increasing the overall energy-storage performance.The CF/MnO_(2)-I ESSs show a 12.6-fold(or higher) increased volumetric energy density of 793.81 mWh L^(-1)at a current of 10 μA relative to ESSs using CF/MnO_(2)without I-RMs(CF/MnO_(2)).Moreover,the CF/MnO_(2)-I retains 93.1% of its initial capacitance after 10,000 cycles,validating the excellent cyclability.Finally,the flexibility of the ESSs is tested at different bending angles(180° to 0°),demonstrating its feasibility for flexible and high-wear environments.Therefore,CF/MnO_(2)electrodes present a practical material combination for high-performance flexible energy-storage devices owing to the catalytic faradaic interaction with I-RMs.

Hybrid Deep Learning Enabled Load Prediction for Energy Storage Systems

Recent economic growth and development have considerably raised energy consumption over the globe.Electric load prediction approaches become essential for effective planning,decision-making,and contract evaluation of the power systems.In order to achieve effective forecasting outcomes with minimumcomputation time,this study develops an improved whale optimization with deep learning enabled load prediction(IWO-DLELP)scheme for energy storage systems(ESS)in smart grid platform.The major intention of the IWO-DLELP technique is to effectually forecast the electric load in SG environment for designing proficient ESS.The proposed IWO-DLELP model initially undergoes pre-processing in two stages namely min-max normalization and feature selection.Besides,partition clustering approach is applied for the decomposition of data into distinct clusters with respect to distance and objective functions.Moreover,IWO with bidirectional gated recurrent unit(BiGRU)model is applied for the prediction of load and the hyperparameters are tuned by the use of IWO algorithm.The experiment analysis reported the enhanced results of the IWO-DLELP model over the recent methods interms of distinct evaluation measures.

Combined hybrid energy storage system and transmission grid model for peak shaving based on time series operation simulation

This study proposes a combined hybrid energy storage system(HESS) and transmission grid(TG) model, and a corresponding time series operation simulation(TSOS) model is established to relieve the peak-shaving pressure of power systems under the integration of renewable energy. First, a linear model for the optimal operation of the HESS is established, which considers the different power-efficiency characteristics of the pumped storage system, electrochemical storage system, and a new type of liquid compressed air energy storage. Second, a TSOS simulation model for peak shaving is built to maximize the power entering the grid from the wind farms and HESS. Based on the proposed model, this study considers the transmission capacity of a TG. By adding the power-flow constraints of the TG, a TSOS-based HESS and TG combination model for peak shaving is established. Finally, the improved IEEE-39 and IEEE-118 bus systems were considered as examples to verify the effectiveness and feasibility of the proposed model.

Energy Management and Capacity Optimization of Photovoltaic, Energy Storage System, Flexible Building Power System Considering Combined Benefit

Building structures themselves are one of the key areas of urban energy consumption,therefore,are a major source of greenhouse gas emissions.With this understood,the carbon trading market is gradually expanding to the building sector to control greenhouse gas emissions.Hence,to balance the interests of the environment and the building users,this paper proposes an optimal operation scheme for the photovoltaic,energy storage system,and flexible building power system(PEFB),considering the combined benefit of building.Based on the model of conventional photovoltaic(PV)and energy storage system(ESS),the mathematical optimization model of the system is proposed by taking the combined benefit of the building to the economy,society,and environment as the optimization objective,taking the near-zero energy consumption and carbon emission limitation of the building as the main constraints.The optimized operation strategy in this paper can give optimal results by making a trade-off between the users’costs and the combined benefits of the building.The efficiency and effectiveness of the proposed methods are verified by simulated experiments.

Health Data Availability Protection:Delta-XOR-Relay Data Update in Erasure-Coded Cloud Storage Systems

To achieve the high availability of health data in erasure-coded cloud storage systems,the data update performance in erasure coding should be continuously optimized.However,the data update performance is often bottlenecked by the constrained cross-rack bandwidth.Various techniques have been proposed in the literature to improve network bandwidth efficiency,including delta transmission,relay,and batch update.These techniques were largely proposed individually previously,and in this work,we seek to use them jointly.To mitigate the cross-rack update traffic,we propose DXR-DU which builds on four valuable techniques:(i)delta transmission,(ii)XOR-based data update,(iii)relay,and(iv)batch update.Meanwhile,we offer two selective update approaches:1)data-deltabased update,and 2)parity-delta-based update.The proposed DXR-DU is evaluated via trace-driven local testbed experiments.Comprehensive experiments show that DXR-DU can significantly improve data update throughput while mitigating the cross-rack update traffic.

DNA Computing with Water Strider Based Vector Quantization for Data Storage Systems

The exponential growth of data necessitates an effective data storage scheme,which helps to effectively manage the large quantity of data.To accomplish this,Deoxyribonucleic Acid(DNA)digital data storage process can be employed,which encodes and decodes binary data to and from synthesized strands of DNA.Vector quantization(VQ)is a commonly employed scheme for image compression and the optimal codebook generation is an effective process to reach maximum compression efficiency.This article introduces a newDNAComputingwithWater StriderAlgorithm based Vector Quantization(DNAC-WSAVQ)technique for Data Storage Systems.The proposed DNAC-WSAVQ technique enables encoding data using DNA computing and then compresses it for effective data storage.Besides,the DNAC-WSAVQ model initially performsDNA encoding on the input images to generate a binary encoded form.In addition,aWater Strider algorithm with Linde-Buzo-Gray(WSA-LBG)model is applied for the compression process and thereby storage area can be considerably minimized.In order to generate optimal codebook for LBG,the WSA is applied to it.The performance validation of the DNAC-WSAVQ model is carried out and the results are inspected under several measures.The comparative study highlighted the improved outcomes of the DNAC-WSAVQ model over the existing methods.

Optimal Management of Energy Storage Systems for Peak Shaving in a Smart Grid

In this paper,the installation of energy storage systems(EES)and their role in grid peak load shaving in two echelons,their distribution and generation are investigated.First,the optimal placement and capacity of the energy storage is taken into consideration,then,the charge-discharge strategy for this equipment is determined.Here,Genetic Algorithm(GA)and Particle Swarm Optimization(PSO)are used to calculate the minimum and maximum load in the network with the presence of energy storage systems.The energy storage systems were utilized in a distribution system with the aid of a peak load shaving approach.Ultimately,the battery charge-discharge is managed at any time during the day,considering the load consumption at each hour.The results depict that the load curve reached a constant state by managing charge-discharge with no significant changes.This shows the significance of such matters in terms of economy and technicality.

Data Utilization-Based Adaptive Data Management Method for Distributed Storage System in WAN Environment

Recently,research on a distributed storage system that efficiently manages a large amount of data has been actively conducted following data production and demand increase.Physical expansion limits exist for traditional standalone storage systems,such as I/O and file system capacity.However,the existing distributed storage system does not consider where data is consumed and is more focused on data dissemination and optimizing the lookup cost of data location.And this leads to system performance degradation due to low locality occurring in a Wide Area Network(WAN)environment with high network latency.This problem hinders deploying distributed storage systems to multiple data centers over WAN.It lowers the scalability of distributed storage systems to accommodate data storage needs.This paper proposes a method for distributing data in a WAN environment considering network latency and data locality to solve this problem and increase overall system performance.The proposed distributed storage method monitors data utilization and locality to classify data temperature as hot,warm,and cold.With assigned data temperature,the proposed algorithm adaptively selects the appropriate data center and places data accordingly to overcome the excess latency from the WAN environment,leading to overall system performance degradation.This paper also conducts simulations to evaluate the proposed and existing distributed storage methods.The result shows that our proposed method reduced latency by 38%compared to the existing method.Therefore,the proposed method in this paper can be used in large-scale distributed storage systems over a WAN environment to improve latency and performance compared to existing methods,such as consistent hashing.

Distributed Cooperative Control of Battery Energy Storage Systems in DC Microgrids

The control of battery energy storage systems(BESSs)plays an important role in the management of microgrids.In this paper,the problem of balancing the state-ofcharge(SoC)of the networked battery units in a BESS while meeting the total charging/discharging power requirement is formulated and solved as a distributed control problem.Conditions on the communication topology among the battery units are established under which a control law is designed for each battery unit to solve the control problem based on distributed average reference power estimators and distributed average unit state estimators.Two types of estimators are proposed.One achieves asymptotic estimation and the other achieves finite time estimation.We show that,under the proposed control laws,SoC balancing of all battery units is achieved and the total charging/discharging power of the BESS tracks the desired power.A simulation example is shown to verify the theoretical results.

A distributed VSG control method for a battery energy storage system with a cascaded H-bridge in a grid-connected mode

With the high penetration of renewable energy,new challenges,such as power fluctuation suppression and inertial support capability,have arisen in the power sector.Battery energy storage systems play an essential role in renewable energy integration.In this paper,a distributed virtual synchronous generator(VSG)control method for a battery energy storage system(BESS)with a cascaded H-bridge converter in a grid-connected mode is proposed.The VSG is developed without communication dependence,and state-of-charge(SOC)balancing control is achieved using the distributed average algorithm.Owing to the low varying speed of SOC,the bandwidth of the distributed communication networks is extremely slow,which decreases the cost.Therefore,the proposed method can simultaneously provide inertial support and accurate SOC balancing.The stability is also proved using root locus analysis.Finally,simulations under different conditions are carried out to verify the effectiveness of the proposed method.

Corrosion behavior of Q235B carbon steel in simulated seawater pumped storage system under operational conditions

Seawater pumped storage systems have bright prospect for energy storage in the coming years.The operational conditions of seawater pumped storage system are complex and harsh,where metal materials suff er from severe general and local corrosion.The corrosion behavior of Q235B carbon steel in simulated seawater pumped storage system under operational conditions was studied by potentiodynamic polarization,cyclic potentiodynamic polarization,and scanning electron microscope(SEM).The results confi rm that the working pressure aff ected the corrosion resistance of Q235B carbon steel during the whole immersion period.The pressure promoted the electrochemical reaction of corrosion process and the corrosion rate increased with pressure at the initial immersion period.However,the stable rust layer formed after longtime immersion at diff erent pressures increased the corrosion resistance of carbon steel,and decreased the corrosion degree of carbon steel.Meanwhile,the working pressure aff ected the pitting corrosion behavior of Q235B carbon steel during the whole immersion period.The pitting corrosion potential was more negative and the tendency of pitting corrosion was higher at 4 MPa during the whole immersion period.However,pressure also accelerated the formation rate of protective rust layer on the steel surface.Q235B carbon steel has higher susceptibility to pitting corrosion at 4 MPa in the static seawater.

HUSTserver:Implementation for Reliable and High-Performance Network Attached Storage System

Network attached storage (NAS) with the properties of improved scalability, simplified management, low cost and balanced price performance, is desirable for high performance storage systems applied to extensive areas. Unfortunately, it also has some disadvantages such as increased network workload, and inconvenience in disaster recovery. To overcome these disadvantages, we propose a channel bonding technique and provide hot backup functions in the designed NAS system, named HUSTserver. Channel bonding means merging multiple Ethernet channels into integrated one, and that the data packets can be transferred through any available network channels in a parallel mode. The hot backup function provides automatic data mirroring among servers. In this paper, we first describe the whole system prototype from a software and hardware architecture view. Then, multiple Ethernet and hot backup technologies that distinguish HUSTserver from others are discussed in detail. The findings presented demonstrate that network bandwidth can be scaled by the use of multiple commodity networks. Dual parallel channels of commodity 100 Mbps Ethernet are both necessary and sufficient to support the data rates of multiple concurrent file transfers. And the hot backup function introduced in our system provides high data accessibility.

Locally Minimum Storage Regenerating Codes in Distributed Cloud Storage Systems

In distributed cloud storage systems, inevitably there exist multiple node failures at the same time. The existing methods of regenerating codes, including minimum storage regenerating(MSR) codes and minimum bandwidth regenerating(MBR) codes, are mainly to repair one single or several failed nodes, unable to meet the repair need of distributed cloud storage systems. In this paper, we present locally minimum storage regenerating(LMSR) codes to recover multiple failed nodes at the same time. Specifically, the nodes in distributed cloud storage systems are divided into multiple local groups, and in each local group(4, 2) or(5, 3) MSR codes are constructed. Moreover, the grouping method of storage nodes and the repairing process of failed nodes in local groups are studied. Theoretical analysis shows that LMSR codes can achieve the same storage overhead as MSR codes. Furthermore, we verify by means of simulation that, compared with MSR codes, LMSR codes can reduce the repair bandwidth and disk I/O overhead effectively.

Massive energy storage system for effective usage of renewable energy

The current energy trend indicates a strong thrust toward transforming renewable energy as a major power source.To achieve this mission,battery energy storage systems(BESSs)are indispensable.Although BESSs are expensive,cost reduction can be achieved by using BESSs for multiple purposes,such as load leveling,business continuity planning,frequency control,capacity market,arbitrage,and emergency power.In this paper,various applications of BESSs are classified.The possibility of achieving conflict-free combination of different applications is demonstrated.The total required energy storage capacity in Japan is estimated to be 150–200 GWh by 2030.The present status of NaS batteries for multipurpose use and new trends in battery-based businesses are introduced.