Combined Insights from Leachate Structure and Microstructure Characteristics for Eating Quality of Convenience Rice Processed by Super-Heated and Pressurized Steam Technologies

Convenience rice has become widely popular due to its easy availability for cooking. This study investigated the starch structure and composition of leachate and the microstructure of reheated convenience rice using novel processing technologies: super-heated steaming(SHS), auto-electric cooking(AEC), and pressurized-steam cooking(PSC). Additionally, the effect of two different target water contents(58% and 63%) was also evaluated. The PSC_63% sample had the highest total solids and amylopectin amount in the leachate. The amylopectin amount in the leachate differed significantly based on the targeted water content. Morphological characterization revealed that the swelling of starch and the coated layer on the surface of rice grains were most pronounced in the PSC_63% sample due to the pressure processing. The textural hardness of the AEC_58% sample was much higher than that of the other samples. The PSC_63% sample had the highest textural adhesiveness value, which can be attributed to the highest amylopectin amount in the leachate. Sensory characterization showed that the PSC_63% sample had the highest glossiness, whiteness, moistness, and overall acceptability. The principal component analysis score plots presented substantial differences in the leachate and textural and sensory characteristics of reheated convenience rice among the different processing technologies.

Effects of processing parameters on fabrication defects,microstructure and mechanical properties of additive manufactured Mg–Nd–Zn–Zr alloy by selective laser melting process

Mg–3Nd–0.2Zn–0.4Zr(NZ30K,wt.%)alloy is a new kind of high-performance metallic biomaterial.The combination of the NZ30K Magnesium(Mg)alloy and selective laser melting(SLM)process seems to be an ideal solution to produce porous Mg degradable implants.However,the microstructure evolution and mechanical properties of the SLMed NZ30K Mg alloy were not yet studied systematically.Therefore,the fabrication defects,microstructure,and mechanical properties of the SLMed NZ30K alloy under different processing parameters were investigated.The results show that there are two types of fabrication defects in the SLMed NZ30K alloy,gas pores and unfused defects.With the increase of the laser energy density,the porosity sharply decreases to the minimum first and then slightly increases.The minimum porosity is 0.49±0.18%.While the microstructure varies from the large grains with lamellar structure inside under low laser energy density,to the large grains with lamellar structure inside&the equiaxed grains&the columnar grains under middle laser energy density,and further to the fine equiaxed grains&the columnar grains under high laser energy density.The lamellar structure in the large grain is a newly observed microstructure for the NZ30K Mg alloy.Higher laser energy density leads to finer grains,which enhance all the yield strength(YS),ultimate tensile strength(UTS)and elongation,and the best comprehensive mechanical properties obtained are YS of 266±2.1 MPa,UTS of 296±5.2 MPa,with an elongation of 4.9±0.68%.The SLMed NZ30K Mg alloy with a bimodal-grained structure consisting of fine equiaxed grains and coarser columnar grains has better elongation and a yield drop phenomenon.

Deep structure of the Southeast Asian curved subduction system and its dynamic process

The deep structure,material circulation,and dynamic processes in the Southeast Asia have long been an elusive scientific puzzle due to the lack of systematic scientific observations and recognized theoretical models.Based on the deep seismic tomography using long-period natural earthquake data,in this study,the deep structure and material circulation of the curved subduction system in Southeast Asia was studied,and the dynamic processes since 100 million years ago was reconstructed.It is pointed out that challenges still exist in the precise reconstruction of deep mantle structures of the study area,the influence of multi-stage subduction on deep material exchange and shallow magma activity,as well as the spatiotemporal evolution and coupling mechanism of multi-plate convergence.Future work should focus on high-resolution land-sea joint 3-D seismic tomography imaging of the curved subduction system in the Southeast Asia,combined with geochemical analysis and geodynamic modelling works.

On-line detection system of weld-based rapid prototyping process based on structured light

In order to realize the closed-loop control for rapid prototyping process based on gas metal arc welding, the geometric parameters of weld beads should be detected. In this study, a vision sensor system consisting of a linear laser projector and a CCD camera was designed to collect images of weld beads. Then, an image processing approach which combines with a Gaassian filter and an improved gravity method was used to extract the centerline of a light stripe based on VC ＋＋. Feature points of the centerline were identical directly by means of an image fusion algorithm. Experimental results show that image fusion is an effective approach to measure the width and height of the weld bead with high accuracy. This method can identify beads effectively in multi-pass welding and avoid designing different modes to suit all kinds of shapes.

A process monitoring method for autoregressive-dynamic inner total latent structure projection

As a dynamic projection to latent structures(PLS)method with a good output prediction ability,dynamic inner PLS(DiPLS)is widely used in the prediction of key performance indi-cators.However,due to the oblique decomposition of the input space by DiPLS,there are false alarms in the actual industrial process during fault detection.To address the above problems,a dynamic modeling method based on autoregressive-dynamic inner total PLS(AR-DiTPLS)is proposed.The method first uses the regression relation matrix to decompose the input space orthogonally,which reduces useless information for the predic-tion output in the quality-related dynamic subspace.Then,a vector autoregressive model(VAR)is constructed for the predic-tion score to separate dynamic information and static informa-tion.Based on the VAR model,appropriate statistical indicators are further constructed for online monitoring,which reduces the occurrence of false alarms.The effectiveness of the method is verified by a Tennessee-Eastman industrial simulation process and a three-phase flow system.

MICROSTRUCTURE OF BINARY Mg-Al EUTECTIC ALLOY WIRES PRODUCED BY THE OHNO CONTINUOUS CASTING PROCESS

Directionally solidified binary Mg-Al eutectic alloy wires of approximately 5 mm in diameter were produced by the Ohno continuous casting （OCC） process and the microstructure was examined. It was found that the wires possess obvious unidirectional growth characteristic along its axial direction. The microstructure consists of parallel columnar grains that resulted from the competitive growth of equiaxed grains solidified on the head of dummy bar. Each columnar grain comprises regular eutectic a-Mg and β-Mg17 Al12 phases, which grew along the axial direction of the wires. The morphology of the eutectic is mainly lamellar, meanwhile rod eutectic exists. The formation of rod eutectic was attributed to the ＂bridging effect＂ caused by incidental elements in the alloy.

Effects of compressing and remelting in SIMA processing on semi-solid structure evolution of an Al-Zn wrought alloy

Structure evolution of an Al-Zn wrought alloy in remelting processing in thestrain induced melt activated (SIMA) serai-solid procedure was observed, and effects of factors, theremelting temperature, the holding time, and the compression strain, on structures and grain sizesof the alloy were investigated. The results show that (1) the proper temperature of remelting is inthe range of 610 to 615℃; (2) the grain size in specimen with greater compression strain is smallerthan that with smaller compression strain in condition of the same remelting temperature andholding time, and the grain size in local area with great local equivalent strain is smaller thanthat with small one; (3) liquid occurs in form of cluster in matrix during remelting and itsquantity increases with remelting time increasing; liquid in specimen with great compression strainoccurs earlier than that with small one, and quantity of liquid in the center of specimen withgreater local equivalent strain is greater than that in the two ends of it; (4) distortion energyafter deforming in matrix of the alloy is the significant factor to activate melting of matrix atlocal area with great local equivalent strain.

Effect of milling process on the core-shell structures and dielectric properties of fine-grained BaTiO_3-based X7R ceramic materials

Fine-grained BaTiO3-based X7R ceramic materials were prepared and the effects of milling process on the core-shell structures and dielectric properties were investigated using scanning electron microscope, transmission electron microscope, and energy dispersive spectroscopy （EDS）. As the milling time extends, the dielectric constant of the ceramics increases, whereas the temperature coefficient of capacitance at 125℃ drops quickly. The changes in dielectric properties are considered relevant to the microstructure evolution caused by the milling process. Defects on the surface of BaTiO3 particles increase because of the effects of milling process, which will make it easier for additives to diffuse into the interior grains. As the milling time increases, the shell region gets thicker and the core region gets smaller; however, EDS results show that the chemical inhomogeneity between grain core and grain shell becomes weaker.

THE STRUCTURE CONTROL OF ALUMINUM FOAMS PRODUCED BY POWDER COMPACTED FOAMING PROCESS

A new technique, powder compact foaming process for the production of aluminumfoams has been studied in this article. According to this method, the aluminum pow-der is mixed with a powder foaming agent (TiH_2). Subsequent to mixing, the powderblend is hot compacted to obtain a dense semi--finished product. Upon heating to tem-peratures within the range of the melting point, the foaming agent decomposes to evolvegas and the semi--finished product expands into a porous cellular aluminum. Foamingprocess is the key in this method. Based on experiments, the foaming characteris-tics were mainly analyzed and discussed. Experiments show that the aluminum--foamwith closed pores and a uniform cell structure of high porosity can be obtained usingthis method by adjusting the foaming parameters: the content of foaming agent andfoaming temperature.

Effect of Valence Electron Structure on Temper Process and Hardness of the Supersaturated Carburized Layer

By measuring the hardness of carburized layer of a new type supersaturated carburizing steel （35Cr3SiMnMoV） at different temper temperature for 2 h, the relationship curve between the carburized layer hardness and the temper temperature is established. The result indicates that the hardness goes down firstly, then up and down, just like a wave consistent with the temperature increase. A secondary hardening peak appears at 570 ℃ or so. Based on Empirical Election Theory （EET） of Solids and Molecules, the valence electron structures （VESs） containing α-Fe-C, α-Fe-C-Me segregation structure units and carbide are calculated. The laws of temper process and hardness change with the temper temperature are explained, and the fact that reconstruction of θ-Fe3C is prior to that of special carbide at high tempering is analyzed with the phase structure formation factor, S, being taken into consideration. Therefore, the laws of temper process and hardness change of supersaturated carburized layer at different temper temperature can be traced back to valence electron structure （VES） level of alloy phase.

Structure and Raman Spectroscopy of Nanocrystalline TiO_(2) Powder Derived by Sol-Gel Process

Nanocrystalline TiO_(2) powder was prepared by sol-gel process.The structures of the as-prepared and the TiO_(2) powder heat-treated at different temperatures were studied by thermogravimetric analyzer,differential thermal analysis,x-ray diffraction,and Raman spectra.As the powder was heat-treated at 350℃,it turned into tetragonal anatase structure.A structural transformation from anatase to rutile type occurred and the grains of the powder grew drastically when the powder was heat-treated at above 550℃.The structural transformation from anatase to rutile type completed at 750℃.The Raman spectra of TiO_(2) nanocrystalline powder were also studied.

Pore structure of ore granular media by computerized tomography image processing

The pore structure images of ore particles located at different heights of leaching column were scanned with X-ray computerized tomography (CT) scanner, the porosity and pore size distribution were calculated and the geometrical shape and connectivity of pores were analyzed based on image process method, and the three dimensional reconstruction of pore structure images was realized. The results show that the porosity of ore particles bed in leaching column is 42.92%, 41.72%, 39.34% at top, middle and bottom zone, respectively. Obviously it has spatial variability and decreases appreciably along the height of the column. The overall average porosity obtained by image processing is 41.33% while the porosity gotten from general measurement method in laboratory is 42.77% showing the results of both methods are consistent well. The pore structure of ore granular media is characterized as a dynamical space network composed of interconnected pore bodies and pore throats. The ratio of throats with equivalent diameter less than 1.91 mm to the total pores is 29.31%, and that of the large pores with equivalent diameter more than 5.73 mm is 2.90%.

A Multi-level Approach for Complex Fault Isolation Based on Structured Residuals

In industrial processes,there exist faults that have complex effect on process variables.Complex and simple faults are defined according to their effect dimensions.The conventional approaches based on structured residuals cannot isolate complex faults.This paper presents a multi-level strategy for complex fault isolation.An extraction procedure is employed to reduce the complex faults to simple ones and assign them to several levels.On each level,faults are isolated by their different responses in the structured residuals.Each residual is obtained insensitive to one fault but more sensitive to others.The faults on different levels are verified to have different residual responses and will not be confused.An entire incidence matrix containing residual response characteristics of all faults is obtained,based on which faults can be isolated.The proposed method is applied in the Tennessee Eastman process example,and the effectiveness and advantage are demonstrated.

Microstructure Evolution of Semi-solid Processed Hyper-eutectic Al-30%Si Alloy

An investigation was made on the influences of mechanical stirring on microstructure of hyper-eutectic Al-30%Si alloy (inmass fraction) during solidification. The primary Si crystals formed in the alloy melt were gradually changed from elongated platelets tonear-spherical shapes by mechanical stirring. The spheroidization of primary St crystals occurs by the mechanism of bending and fractureof Si platelets, wear and collision between Si crystals, and coalescence of small Si particles. The influence of under-cooling and coolingrate of the alloy melt on primary Si crystals of semi-solid processed alloys is investigated as well. The increase of under-cooling andcooling rate decreases the size of primary Si crystals.

A Kernel Time Structure Independent Component Analysis Method for Nonlinear Process Monitoring

Kernel independent component analysis(KICA) is a newly emerging nonlinear process monitoring method,which can extract mutually independent latent variables called independent components(ICs) from process variables. However, when more than one IC have Gaussian distribution, it cannot extract the IC feature effectively and thus its monitoring performance will be degraded drastically. To solve such a problem, a kernel time structure independent component analysis(KTSICA) method is proposed for monitoring nonlinear process in this paper. The original process data are mapped into a feature space nonlinearly and then the whitened data are calculated in the feature space by the kernel trick. Subsequently, a time structure independent component analysis algorithm, which has no requirement for the distribution of ICs, is proposed to extract the IC feature.Finally, two monitoring statistics are built to detect process faults. When some fault is detected, a nonlinear fault identification method is developed to identify fault variables based on sensitivity analysis. The proposed monitoring method is applied in the Tennessee Eastman benchmark process. Applications demonstrate the superiority of KTSICA over KICA.

Investigation of system structure and information processing mechanism for cognitive skywave over-the-horizon radar

Based on the cognitive radar concept and the basic connotation of cognitive skywave over-the-horizon radar（SWOTHR）, the system structure and information processingmechanism about cognitive SWOTHR are researched. Amongthem, the hybrid network system architecture which is thedistributed configuration combining with the centralized cognition and its soft/hardware framework with the sense-detectionintegration are proposed, and the information processing framebased on the lens principle and its information processing flowwith receive-transmit joint adaption are designed, which buildand parse the work law for cognition and its self feedback adjustment with the lens focus model and five stages informationprocessing sequence. After that, the system simulation andthe performance analysis and comparison are provided, whichinitially proves the rationality and advantages of the proposedideas. Finally, four important development ideas of futureSWOTHR toward ＂high frequency intelligence information processing system＂ are discussed, which are scene information fusion, dynamic reconfigurable system, hierarchical and modulardesign, and sustainable development. Then the conclusion thatthe cognitive SWOTHR can cause the performance improvement is gotten.

Influence of Process Variables on the Structure of Mechanically Alloyed Ti_3Al-base Intermetallics

During mechanical alloying variables such as the type of mill,milling intensity,milling time,milling at- mosphere and ball-to-powder weight ratio(BPR)affect the morphology and constitution of the product. The effect of milling time,milling atmosphere and BPR on the nature of the product formed in mechanical- ly alloyed pure Ti and blended elemental binary Ti-Al,and ternary Ti-AI-Nb alloy powders was described. Mechanical alloying of pure titanium results,after long milling times,in the formation of an fcc phase.In the binary alloy,a solid solution of aluminum in titanium,an amorphous phase,and a fcc phase form with increasing milling time.The fcc phase,which is probably a result of TiN formation,occurs more rapidly in air or nitrogen than in an inert atmosphere.Formation of the B2 phase in the ternary alloys depends both on alloy composition and the milling atmosphere,with 100％ formation in all atmospheres in Ti-25Al-25Nb but not in Ti-24Al-11Nb,and an inert atmosphere favoring formation.The times required for the formation of the different phases decrease as the BPR increases;but their sequence is unaffected.Based on this infor- mation,“milling maps”which describe phase formation as a function of the BPR and milling time are con- structed.Contamination from the milling balls increased as the BPR was increased.

EFFECT OF STRESS-INDUCED REACTIONS ON MORPHOLOGICAL STRUCTURE AND PROCESSABILITY OF PVC DURING PAN-MILLING

The effect of pan-milling on morphological structure,processability and properties of PVC was studied throughSEM,FTIR,granulometer,GPC and mechanical properties test in the hope of gaining ease in operation,needless ofplasticizers,a clean and efficient route for improving the processability of PVC through stress-induced reactions,fulfilling the idea of“plasticizing PVC by itself”.The experimental results show that during pan-milling at ambienttemperature,within 2-3 min,the microcrystalline structure of PVC becomes indistinct,the grain size of PVC is reducedfrom 130-160 μm to 1-50 μm the molecular weight of PVC is slightly decreased,the variation of molecular weightdistribution is indistinct,the plasticizing time and torque at balance drop a great deal from 71-132 s to 31-33 s and from18.2-22.1 Nm to 14.7-18.4 Nm,respectively,the processability of PVC is markedly improved,and the mechanicalproperties get enhanced too.

Polyol Process to Large-scale Synthesis of Cu_2O with Disk-like Structure

A new form of Cu2O, disk-like structure with 60 nm in thickness and 2 μm in diameter,has been successfully synthesized in bulk quantities by polyol process in the presence of PVP K-30.

Structure and electrochemical properties of hypo-stoichiometric hydro-gen storage alloys prepared by twin-roller rapid quenching process

The stoichiometric alloy MlB5.0 and the hypo-stoichiometric alloy MlB4.85 were prepared by twin-roller rapid quenching process, and their structure and electrochemical properties were studied. The results of XRD show that both of the alloys have a typical single-phase hexagonal CaCus-type structure. The cell volume of the hylpo-stoichiometric alloy M1B4.85 is slightly larger than that of the stoichiometric alloy M1B5.0, although its lattice constant cla is smaller. Under 2 C discharging rate, i.e. 640 mA/g, the M1B4.85 has a discharge capacity of 320 mAh/g, which is higher than that of the M1Bs.o, 312 mAh/g. Nevertheless, the capacities of the M1B4.85 and the M1Bs.o decline 24.7% and 20.2% after 400 cycles, respectively. The relationship of electrochemical performances of the alloys with their structures is discussed.