Corrosion is a primary cause of the slippage of friction⁃type high⁃strength bolted(FHSB)T⁃stub connections.This paper attempts to quantify the residual capacity of FHSB T⁃stub connections with corroded nuts.Firstly,co...Corrosion is a primary cause of the slippage of friction⁃type high⁃strength bolted(FHSB)T⁃stub connections.This paper attempts to quantify the residual capacity of FHSB T⁃stub connections with corroded nuts.Firstly,corrosion simulation tests were conducted on 48 manually cut nuts to find out the relationship between the damage degree of nut section and the residual clamping force(RCF)of bolt.Then,static load tests were carried out on 24 FHSB T⁃stub connections with nuts of different degrees of damage to obtain the failure modes.By finite⁃element(FE)models,a comparative analysis was performed on the initial friction load(IFL)and ultimate strength(US)of each connection with corroded nuts.Finally,the parameters of 96 FE models for FHSB T⁃stub connections were analyzed and used to derive the calculation formulas for the degree of damage for each nut and the IFL and US of each connection.The results show that the RCF decay of a bolt is a quadratic function of the equivalent radius loss ratio and the shear failure after nut corrosion;the IFL of each connection had a clear linear correlation with the RCF of the corresponding bolts,and the correlation depends on the applied load and static friction on connecting plate interface induced by the clamping force;the static friction had little impact on the US of the connection;the proposed IFL and US formulas can effectively derive the residual anti⁃slip capacity of FHSB T⁃stub connections from the degree of damage of the corroded nut section.The research results provide a scientific basis for the replacement and maintenance of corroded bolts of FHSB T⁃stub connections.展开更多
In the Ion Cyclotron Range of Frequency (ICRF) heating experiment, impedance matching is of great practical significance, because wide variations in antenna loading are observed within the discharge, in tokamaks opera...In the Ion Cyclotron Range of Frequency (ICRF) heating experiment, impedance matching is of great practical significance, because wide variations in antenna loading are observed within the discharge, in tokamaks operating in H-mode. A sudden decrease in antenna loading accompanying the L-mode to H-mode transition typically occurs on a timescale of a few milliseconds, as does the increase in loading at the H- to L-mode transition. Therefore, it is necessary to match dynamically in the transmission line between the generator output and the antenna input connections[1]. A new type of stub tuner being developed utilizes the difference in radio-frequency wavelengths between gas and liquid due to different relative dielectric constants. The impedance matching can be adjusted in realtime in an attempt to track the variations in the antenna loading. Since there are no mechanically moving parts in the short ends of stub, the change can be more convenient and safe, moreover, it can withstand higher voltage without breakdown. This system device will be applied in the HT-7 superconductor Tokamak ICRF experiment.展开更多
This paper studies the contribution of CFRP(carbon fiber-reinforced polymer)to the mechanical behavior of high strength concrete-filled square steel tube(HCFST)under biaxial eccentric compression.The new type of compo...This paper studies the contribution of CFRP(carbon fiber-reinforced polymer)to the mechanical behavior of high strength concrete-filled square steel tube(HCFST)under biaxial eccentric compression.The new type of composite member is composed of an inner CFRP tube and an outer steel tube with concrete filled in the two tubes.The finite element analysis was made by ABAQUS on the behavior of high strength concrete filled square steel tubular columns with inner CFRP circular tube subjected to bi-axial eccentric loading.The results obtained from the finite element analysis were verified with the experimental results.In addition,the load-deflection curves in the whole process were calculated and analyzed,which can be divided into three segments:Elastic phase,plastic phase,descending phase.Based on the load-deflection curves,the stresses analysis on the core concrete,CFRP tube and steel tube were conducted.The confinement effect of the CFRP tube improves the ductility of HCFST-CFRP stub column.CFRP ratio and eccentricity affect the ultimate bearing capacity of HCFST stub column.Finally,a calculation formula of ultimate bearing capacity was proposed in the paper.展开更多
In microwave circuit and aerial system, impedance matching is very important. Liquid stub tuner is a new type of impedance matching device. In the HT-7 Tokamak Ion Cyclotron Resonance Heating ( ICRH ) system, we have ...In microwave circuit and aerial system, impedance matching is very important. Liquid stub tuner is a new type of impedance matching device. In the HT-7 Tokamak Ion Cyclotron Resonance Heating ( ICRH ) system, we have already adopted liquid stub tuner to replace the conventional stub tuner. It is urgent to develop a control system of the liquid stub tuner. This paper mainly introduces the design and realization of the liquid stub tuner control system , and briefly introduces its three controlling functions: local control, remote control and computer control.展开更多
To realize equal power splitting at two arbitrary gigahertz-frequencies, this paper presents a new type of Wilkinson dual frequency power divider, consisting of three-section transmission lines and a series RLC(resist...To realize equal power splitting at two arbitrary gigahertz-frequencies, this paper presents a new type of Wilkinson dual frequency power divider, consisting of three-section transmission lines and a series RLC(resistor, inductor and capacitor)circuit. By equating the [ABCD] matrix of the proposed circuit to that of the quarter-wave impedance transformer, coupled with even/odd mode analyses, the design equations of the proposed network are derived. For verification, two dual-frequency power dividers with dual-band operating frequencies at 0.6 GHz and 3.0 GHz, and 3.8 GHz and 10 GHz respectively are designed and simulated. Simulation results show that the dual-band ratio of the proposed power divider can be as large as 5. Comparisons of the simulation results at X-band and S-band with different power dividers indicate that the proposed dual-band power divider performs better under the scenario of the upper operating frequency extending to X-band.展开更多
The paper studies photon-associated transmission through a quantum wire with a side-coupled stub tuner, to which an external microwave field applies, in terms of the approach developed by Cai. The inelastic scattering...The paper studies photon-associated transmission through a quantum wire with a side-coupled stub tuner, to which an external microwave field applies, in terms of the approach developed by Cai. The inelastic scattering of an incoming electron and the photon field lead to photon-electronic transmission though quantum wire. It is found that single photon absorbing (emitting) of the incoming electron in the stub can bring about antiresonant transmission in the quantum wire. The influence of the feedback mechanism from inelastic scattering process on elastic channel transmission is also examined. Total transmission coefficient as a function of photon energy exhibits non-periodic oscillation peaks. With the increasing of photon-electron coupling constant, the amplitude of these oscillation peaks enhances. Key words stub tuner - photon-associated transport - antiresonance PASC 2001 N72.25 Dc - 73.40.Ty - 73.23. Ad展开更多
A miniaturized square resonator bandpass filter with circular stubs is designed, fabricated, and characterized. Analytical calculations were carried out to determine the critical filter parameters and the design was o...A miniaturized square resonator bandpass filter with circular stubs is designed, fabricated, and characterized. Analytical calculations were carried out to determine the critical filter parameters and the design was optimized using a 3D electromagnetic finite-element solver. The measured results were in good agreement with the designed results. The proposed filter exhibits significant improvement in bandwidth compared to the conventional square resonator bandpass filters.展开更多
The impedance matching is crucial for continuous wave operation of ion cyclotron resonance heating（ICRH） antennae with high power injection into plasmas.A sudden increase in the reflected radio frequency power due t...The impedance matching is crucial for continuous wave operation of ion cyclotron resonance heating（ICRH） antennae with high power injection into plasmas.A sudden increase in the reflected radio frequency power due to an impedance mismatch of the ICRH system is an issue which must be solved for present-day and future fusion reactors.This paper presents a method for theoretical analysis of ICRH system impedance matching for a triple liquid stub tuner under plasma operational conditions.The relationship of the antenna input impedance with the plasma parameters and operating frequency is first obtained using a global solution.Then,the relations of the plasma parameters and operating frequency with the matching liquid heights are indirectly obtained through numerical simulation according to transmission line theory and matching conditions.The method provides an alternative theoretical method,rather than measurements,to study triple liquid stub tuner impedance matching for ICRH,which may be beneficial for the design of ICRH systems on tokamaks.展开更多
文摘Corrosion is a primary cause of the slippage of friction⁃type high⁃strength bolted(FHSB)T⁃stub connections.This paper attempts to quantify the residual capacity of FHSB T⁃stub connections with corroded nuts.Firstly,corrosion simulation tests were conducted on 48 manually cut nuts to find out the relationship between the damage degree of nut section and the residual clamping force(RCF)of bolt.Then,static load tests were carried out on 24 FHSB T⁃stub connections with nuts of different degrees of damage to obtain the failure modes.By finite⁃element(FE)models,a comparative analysis was performed on the initial friction load(IFL)and ultimate strength(US)of each connection with corroded nuts.Finally,the parameters of 96 FE models for FHSB T⁃stub connections were analyzed and used to derive the calculation formulas for the degree of damage for each nut and the IFL and US of each connection.The results show that the RCF decay of a bolt is a quadratic function of the equivalent radius loss ratio and the shear failure after nut corrosion;the IFL of each connection had a clear linear correlation with the RCF of the corresponding bolts,and the correlation depends on the applied load and static friction on connecting plate interface induced by the clamping force;the static friction had little impact on the US of the connection;the proposed IFL and US formulas can effectively derive the residual anti⁃slip capacity of FHSB T⁃stub connections from the degree of damage of the corroded nut section.The research results provide a scientific basis for the replacement and maintenance of corroded bolts of FHSB T⁃stub connections.
基金Supported by National Natural Science Foundation of China,11447118,11247032,11365011Youth Science Foundation of Science and Technology Department of Jiangxi Province,20151BAB212004,20151BAB212012~~
文摘In the Ion Cyclotron Range of Frequency (ICRF) heating experiment, impedance matching is of great practical significance, because wide variations in antenna loading are observed within the discharge, in tokamaks operating in H-mode. A sudden decrease in antenna loading accompanying the L-mode to H-mode transition typically occurs on a timescale of a few milliseconds, as does the increase in loading at the H- to L-mode transition. Therefore, it is necessary to match dynamically in the transmission line between the generator output and the antenna input connections[1]. A new type of stub tuner being developed utilizes the difference in radio-frequency wavelengths between gas and liquid due to different relative dielectric constants. The impedance matching can be adjusted in realtime in an attempt to track the variations in the antenna loading. Since there are no mechanically moving parts in the short ends of stub, the change can be more convenient and safe, moreover, it can withstand higher voltage without breakdown. This system device will be applied in the HT-7 superconductor Tokamak ICRF experiment.
基金This research was funded by Key Projects of National Natural Science Foundation of China(51938009)National Natural Science Foundation of China(51878419)and(51808353).
文摘This paper studies the contribution of CFRP(carbon fiber-reinforced polymer)to the mechanical behavior of high strength concrete-filled square steel tube(HCFST)under biaxial eccentric compression.The new type of composite member is composed of an inner CFRP tube and an outer steel tube with concrete filled in the two tubes.The finite element analysis was made by ABAQUS on the behavior of high strength concrete filled square steel tubular columns with inner CFRP circular tube subjected to bi-axial eccentric loading.The results obtained from the finite element analysis were verified with the experimental results.In addition,the load-deflection curves in the whole process were calculated and analyzed,which can be divided into three segments:Elastic phase,plastic phase,descending phase.Based on the load-deflection curves,the stresses analysis on the core concrete,CFRP tube and steel tube were conducted.The confinement effect of the CFRP tube improves the ductility of HCFST-CFRP stub column.CFRP ratio and eccentricity affect the ultimate bearing capacity of HCFST stub column.Finally,a calculation formula of ultimate bearing capacity was proposed in the paper.
文摘In microwave circuit and aerial system, impedance matching is very important. Liquid stub tuner is a new type of impedance matching device. In the HT-7 Tokamak Ion Cyclotron Resonance Heating ( ICRH ) system, we have already adopted liquid stub tuner to replace the conventional stub tuner. It is urgent to develop a control system of the liquid stub tuner. This paper mainly introduces the design and realization of the liquid stub tuner control system , and briefly introduces its three controlling functions: local control, remote control and computer control.
文摘To realize equal power splitting at two arbitrary gigahertz-frequencies, this paper presents a new type of Wilkinson dual frequency power divider, consisting of three-section transmission lines and a series RLC(resistor, inductor and capacitor)circuit. By equating the [ABCD] matrix of the proposed circuit to that of the quarter-wave impedance transformer, coupled with even/odd mode analyses, the design equations of the proposed network are derived. For verification, two dual-frequency power dividers with dual-band operating frequencies at 0.6 GHz and 3.0 GHz, and 3.8 GHz and 10 GHz respectively are designed and simulated. Simulation results show that the dual-band ratio of the proposed power divider can be as large as 5. Comparisons of the simulation results at X-band and S-band with different power dividers indicate that the proposed dual-band power divider performs better under the scenario of the upper operating frequency extending to X-band.
文摘The paper studies photon-associated transmission through a quantum wire with a side-coupled stub tuner, to which an external microwave field applies, in terms of the approach developed by Cai. The inelastic scattering of an incoming electron and the photon field lead to photon-electronic transmission though quantum wire. It is found that single photon absorbing (emitting) of the incoming electron in the stub can bring about antiresonant transmission in the quantum wire. The influence of the feedback mechanism from inelastic scattering process on elastic channel transmission is also examined. Total transmission coefficient as a function of photon energy exhibits non-periodic oscillation peaks. With the increasing of photon-electron coupling constant, the amplitude of these oscillation peaks enhances. Key words stub tuner - photon-associated transport - antiresonance PASC 2001 N72.25 Dc - 73.40.Ty - 73.23. Ad
文摘A miniaturized square resonator bandpass filter with circular stubs is designed, fabricated, and characterized. Analytical calculations were carried out to determine the critical filter parameters and the design was optimized using a 3D electromagnetic finite-element solver. The measured results were in good agreement with the designed results. The proposed filter exhibits significant improvement in bandwidth compared to the conventional square resonator bandpass filters.
基金supported by the National Magnetic Confinement Fusion Science Program of China(Nos.2014GB108002,2013GB107001)National Natural Science Foundation of China(Nos.11205086,11205053,11375085,and 11405082)+1 种基金the Construct Program of Fusion and Plasma Physics Innovation Team in Hunan Province,China(No.NHXTD03)the Natural Science Foundation of Hunan Province,China(No.2015JJ4044)
文摘The impedance matching is crucial for continuous wave operation of ion cyclotron resonance heating（ICRH） antennae with high power injection into plasmas.A sudden increase in the reflected radio frequency power due to an impedance mismatch of the ICRH system is an issue which must be solved for present-day and future fusion reactors.This paper presents a method for theoretical analysis of ICRH system impedance matching for a triple liquid stub tuner under plasma operational conditions.The relationship of the antenna input impedance with the plasma parameters and operating frequency is first obtained using a global solution.Then,the relations of the plasma parameters and operating frequency with the matching liquid heights are indirectly obtained through numerical simulation according to transmission line theory and matching conditions.The method provides an alternative theoretical method,rather than measurements,to study triple liquid stub tuner impedance matching for ICRH,which may be beneficial for the design of ICRH systems on tokamaks.
