Engineering oxygen vacancies on Tb-doped ceria supported Pt catalyst for hydrogen production through steam reforming of long-chain hydrocarbon fuels

Steam reforming of long-chain hydrocarbon fuels for hydrogen production has received great attention for thermal management of the hypersonic vehicle and fuel-cell application.In this work,Pt catalysts supported on CeO_(2)and Tb-doped CeO_(2)were prepared by a precipitation method.The physical structure and chemical properties of the as-prepared catalysts were characterized by powder X-ray diffraction,scanning electron microscopy,transmission electron microscopy,Raman spectroscopy,H_(2)temperature programmed reduction,and X-ray photoelectron spectroscopy.The results show that Tb-doped CeO_(2)supported Pt possesses abundant surface oxygen vacancies,good inhibition of ceria sintering,and strong metal-support interaction compared with CeO_(2)supported Pt.The catalytic performance of hydrogen production via steam reforming of long-chain hydrocarbon fuels(n-dodecane)was tested.Compared with 2Pt/CeO_(2),2Pt/Ce_(0.9)Tb_(0.1)O_(2),and 2Pt/Ce_(0.5)Tb_(0.5)O_(2),the 2Pt/Ce_(0.7)Tb_(0.3)O_(2)has higher activity and stability for hydrogen production,on which the conversion of n-dodecane was maintained at about 53.2%after 600 min reaction under 700℃at liquid space velocity of 9 ml·g^(-1)·h^(-1).2Pt/CeO_(2)rapidly deactivated,the conversion of n-dodecane was reduced to only 41.6%after 600 min.

Ethanol steam reforming over Ni/ZSM-5 nanosheet for hydrogen production

Compared to reforming reactions using hydrocarbons,ethanol steam reforming(ESR)is a sustainable alternative for hydrogen(H_(2))production since ethanol can be produced sustainably using biomass.This work explores the catalyst design strategies for preparing the Ni supported on ZSM-5 zeolite catalysts to promote ESR.Specifically,two-dimensional ZSM-5 nanosheet and conventional ZSM-5 crystal were used as the catalyst carriers and two synthesis strategies,i.e.,in situ encapsulation and wet impregnation method,were employed to prepare the catalysts.Based on the comparative characterization of the catalysts and comparative catalytic assessments,it was found that the combination of the in situ encapsulation synthesis and the ZSM-5 nanosheet carrier was the effective strategy to develop catalysts for promoting H_(2) production via ESR due to the improved mass transfer(through the 2-D structure of ZSM-5 nanosheet)and formation of confined small Ni nanoparticles(resulted via the in situ encapsulation synthesis).In addition,the resulting ZSM-5 nanosheet supported Ni catalyst also showed high Ni dispersion and high accessibility to Ni sites by the reactants,being able to improve the activity and stability of catalysts and suppress metal sintering and coking during ESR at high reaction temperatures.Thus,the Ni supported on ZSM-5 nanosheet catalyst prepared by encapsulation showed the stable performance with~88% ethanol conversion and~65% H_(2) yield achieved during a 48-h longevity test at 550-C.

面向新质人才需求的STEAM培育机制研究

教育是缓解新质生产力与人才供需矛盾的核心策略,而基础教育则是塑造新质人才不可或缺的基石。为夯实未来新质人才的培育基础,基础教育阶段教育工作者应紧密围绕新质人才的需求,构建一套高效的人才培育机制,助力学生顺利转型为新质人才。在这一过程中,复合型教育目标的引导、跨学科知识体系的重组以及个性化教育策略的定制,为STEAM教育在基础教育阶段赋能新质人才培育提供了强有力的支撑。为了满足新质人才培育的多维需求,教育工作者需从五个关键层面重新构建STEAM教育培育机制:核心培育理念的重塑、根本培育目标的明确、基础培育条件的强化、首要培育策略的制定和关键培育基石的稳固。为了推动STEAM教育在新质人才培育方面更好地适应数智化时代的发展,教育工作者也需采取一系列措施:确保STEAM教育的高效运行,完善其跨学科知识体系,构建虚实联通的STEAM教育空间,提升教师的STEAM素养,并构建一个充满活力的STEAM人才培育新生态。这些措施的实施,将有力推动STEAM教育在培育新质人才方面的创新与发展,为新时代的社会进步贡献力量。

Improvement of low temperature activity and stability of Ni catalysts with addition of Pt for hydrogen production via steam reforming of ethylene glycol

Hydrogen production by steam reforming of ethylene glycol(EG) at 300℃ was investigated over SiO2 and CeO2 supported Pt–Ni bimetallic catalysts prepared by incipient wetness impregnation methods. It was observed that impregnation sequence of Pt and Ni can affect the performance of catalysts apparently. Catalyst with Pt first and then Ni addition showed higher EG conversion and H2 yield owing to the Ni enrichment on the surface and the proper interaction between Pt and Ni. It was observed that although SiO2 supported catalysts exhibited better activity and H2 selectivity, CeO2 supported ones had better stability. This is attributed to the less coke formation on CeO2. Increasing Pt/Ni ratio enhanced the reaction activity, and Pt3–Ni7 catalysts with 3 wt% Pt and 7 wt% Ni showed the highest activity and stability. Ni surficial enrichment facilitated the C-C bond rupture and water gas shift reactions;and Pt addition inhibited methanation reaction. Electron transfer and hydrogen spillover from Pt to Ni suppressed carbon deposition. These combined effects lead to the excellent performance of Pt3–Ni7 supported catalysts.

High-efficient solar-driven hydrogen production by full-spectrum synergistic photo-thermo-catalytic methanol steam reforming with in-situ photoreduced Pt-CuO_(x) catalyst

Synergy between the intrinsic photon and thermal effects from full-spectrum sunlight for H_(2) production is considered to be central to further improve solar-driven H_(2) production.To that end,the photo-thermocatalyst that demonstrates both photoelectronic and photothermal conversion capabilities have drawn much attention recently.Here,we propose a novel synergistic full-spectrum photo-thermo-catalysis technique for high-efficient H_(2) production by solar-driven methanol steam reforming(MSR),along with the Pt-Cu Oxphoto-thermo-catalyst featuring Pt-Cu/Cu_(2)O/CuO heterojunctions by Pt-mediated in-situ photoreduction of Cu O.The results show that the H_(2) production performance rises superlinearly with increasing light intensity.The optimal H_(2) production rate of 1.6 mol g^(-1) h^(-1) with the corresponding solar-to-hydrogen conversion efficiency of 7%and the CO selectivity of 5%is achieved under 15×sun full-spectrum irradiance(1×sun=1 k W m^(-2))at 180°C,which is much more efficient than the previously-reported Cu-based thermo-catalysts for MSR normally operating at 250~350°C.These attractive performances result from the optimized reaction kinetics in terms of intensified intermediate adsorption and accelerated carrier transfer by long-wave photothermal effect,and reduced activation barrier by short-wave photoelectronic effect,due to the broadened full-spectrum absorbability of catalyst.This work has brought us into the innovative technology of full-spectrum synergistic photothermo-catalysis,which is envisioned to expand the application fields of high-efficient solar fuel production.

Hydrogen production from steam reforming of ethanol over Ni/MgO-CeO_2 catalyst at low temperature

MgO,CeO2 and MgO-CeO2 with different mole ratio of Mg:Ce were prepared by solid-phase burning method.Catalysts Ni/MgO,Ni/CeO2 and Ni/MgO-CeO2 were prepared by impregnation method.The catalytic properties were evaluated in ethanol steam reforming(ESR) reaction.Specific surface areas of the supports were measured by nitrogen adsorption-desorption at 77 K,and the catalysts were characterized with X-ray diffraction(XRD),temperature programmed reduction(TPR) and thermogravimetric(TG).The results showed that well...

Hydrogen production at intermediate temperatures with proton conducting ceramic cells:Electrocatalytic activity,durability and energy efficiency

Proton conducting ceramic cells(PCCs)are an attractive emerging technology operating in the intermediate temperature range of 500 to 700℃.In this work,we evaluate the production of hydrogen at intermediate temperatures by proton conducting ceramic cell electrolysis(PCCEL).We demonstrate a highperformance steam electrolysis owing to a composite positrode based on BaGd_(0.8)La_(0.2)Co_(2)O_(6-δ)(BGLC1082)and BaZr0.5Ce0.4Y0.1O3-δ(BZCY541).The high reliability of PCCEL is demonstrated for 1680 h at a current density as high as-0.8 A cm^(-2)close to the thermoneutral cell voltage at 600℃.The electrolysis cell showed a specific energy consumption ranging from 54 to 66 kW h kg^(-1)that is comparable to state-of-the-art low temperature electrolysis technologies,while showing hydrogen production rates systematically higher than commercial solid oxide ceramic cells(SOCs).Compared to SOCs,the results verified the higher performances of PCCs at the relevant operating temperatures,due to the lower activation energy for proton transfer comparing with oxygen ion conduction.However,because of the p-type electronic conduction in protonic ceramics,the energy conversion rate of PCCs is relatively lower in steam electrolysis.The faradaic efficiency of the PCC in electrolysis mode can be increased at lower operating temperatures and in endothermic conditions,making PCCEL a technology of choice to valorize high temperature waste heat from industrial processes into hydrogen.To increase the faradaic efficiency by optimizing the materials,the cell design,or the operating strategy is a key challenge to address for future developments of PCCEL in order to achieve even more superior techno-economic merits.

Analysis of Current Status of Steam Cracking Feed Production and Measures for Maximization of Steam Cracking Feed

In recent years China has seen speedy development of its ethylene industry. Compared to other advanced countries the per capita ethylene consumption in China is still low. With successive startup of grassroots ethylene projects in China after 2006 and debottlenecking and expansion of existing ethylene units China will be confronted with the major issues related with increase of feedstocks for steam cracking. Naphtha is the main feedstock for producing ethylene, and the hydrocracked tail oil is increasing its share in the steam cracker feedstock pool over recent years. This article has analyzed the possibility for maximization of steam cracking feedstock and estimated steam cracker feedstock output based on processing 5 Mt/a of different crudes including the mixed crude transferred through Lu-Ning pipeline and Arabian light crude using corresponding process technologies at the refinery.

Tuning combined steam and dry reforming of methane for “metgas”production: A thermodynamic approach and state-of-the-art catalysts

Nowadays,combined steam and dry reforming of methane(CSDRM)is viewed as a new alternative for the production of high-quality syngas(termed as"metgas",H2:CO of 2.0)suitable for subsequent synthesis of methanol,considered as a promising renewable energy vector to substitute fossil fuel resources.Adequate operation conditions(molar feed composition,temperature and pressure)are required for the sole production of"metgas"while achieving high CH4,CO2 and H2O conversion levels.In this work,thermodynamic equilibrium analysis of CSDRM has been performed using Gibbs free energy minimization where;(i)the effect of temperature(range:200-1000℃),(ii)feed composition(stoichiometric ratio as compared to a feed under excess steam or excess carbon dioxide),(iii)pressure(range:1-20 bar)and,(iv)the presence of a gaseous diluent on coke yields,reactivity levels and selectivity towards"metgas"were investigated.Running CSDRM at a temperature of at least 800℃,a pressure of 1 bar and under a feed composition where CO2-H2O/CH4 is around 1.0,are optimum conditions for the theoretical production of"metgas"while minimizing C(S)formation for longer experimental catalytic runs.A second part of this work presents a review of the recent progresses in the design of(principally)Ni-based catalysts along with some mechanistic and kinetic modeling aspects for the targeted CSDRM reaction.As compared to noble metals,their high availability,low cost and good intrinsic activity levels are main reasons for increasing research dedications in understanding deactivation potentials and providing amelioration strategies for further development.Deactivation causes and main orientations towards designing deactivationresistant supported Ni nanoparticles are clearly addressed and analyzed.Reported procedures based on salient catalytic features(i.e.,acidity/basicity character,redox properties,oxygen mobility,metal-support interaction)and recently employed innovative tactics(such as confinement within mesoporous systems,stabilization through core shell structures or on carbide surfaces)are highlighted and their impact on Ni0reactivity and stability are discussed.The final aspect of this review encloses the major directions and trends for improving synthesis/preparation designs of Ni-based catalysts for the sake of upgrading their usage into industrially oriented combined reforming operations.

Low CO content hydrogen production from oxidative steam reforming of ethanol over CuO-CeO_2 catalysts at low-temperature

CuO-CeO2 catalysts were prepared by a urea precipitation method for the oxidative steam reforming of ethanol at low-temperature.The catalytic performance was evaluated and the catalysts were characterized by inductively coupled plasma atomic emission spectroscopy,X-ray diffraction,temperature-programmed reduction,field emission scanning electron microscopy and thermo-gravimetric analysis.Over CuOCeO2 catalysts,H2 with low CO content was produced in the whole tested temperature range of 250–450 C.The non-noble metal catalyst 20CuCe showed higher H2production rate than 1%Rh/CeO2 catalyst at 300–400 C and the advantage was more obvious after 20 h testing at400 C.These results further confirmed that CuO-CeO2 catalysts may be suitable candidates for low temperature hydrogen production from ethanol.

Steam Reforming of Dimethyl Ether by Gliding Arc Gas Discharge Plasma for Hydrogen Production

Gliding arc gas discharge plasma was used for the generation of hydrogen from steam reforming of dimethyl ether(DME).A systemic procedure was employed to determine the suitable experimental conditions.It was found that DME conversion first increased up to the maximum and then decreased slightly with the increase of added water and air.The increase of total feed gas flow rate resulted in the decrease of DME conversion and hydrogen yield,but hydrogen energy consumption dropped down to the lowest as total feed gas flow rate increased to76 ml·min 1.Larger electrode gap and higher discharge voltage were advantageous.Electrode shape had an important effect on the conversion of DME and production of H2.Among the five electrodes,electrode 2#with valid length of 55 mm and the radian of 34 degrees of the top electrode section was the best option,which enhanced obviously the conversion of DME.

Silicon Nitride Supported Cobalt Catalyst for Enhanced Hydrogen Production from Ethanol Steam Reforming

Silicon nitride(Si_(3)N_(4))supported cobalt catalysts(Co/Si_(3)N_(4))were fabricated by using wetness impregnation procedure.The microscopic morphology,phase composition,and electronic states were characterized by XRD,TEM,SEM,and XPS,respectively.For comparison,cobalt catalyst supported on SiO_(2)(Co/SiO_(2))was also investigated.XPS studies and DFT calculations show that the cobalt species in Co/Si_(3)N_(4) have lower valence state than those in Co/SiO_(2).The catalytic ESR reactions demonstrate that Co/Si_(3)N_(4) exhibits distinctly higher catalytic activity and hydrogen selectivity than Si_(3)N_(4) support and Co/SiO_(2) catalyst with the identical cobalt loading,indicative of the favorable effect of Si_(3)N_(4) support on the catalytic performance of supported cobalt catalyst.Durability tests and TG-DSC studies show that Co/Si_(3)N_(4) catalyst exhibits better stability and resistance to coke during the same catalytic experiment period.

Production of Synthesis Gases from Ethanol Steam Reforming Process

In this study, the production of synthesis gases has been purposed under between 250oC - 700oC and 1 - 2 bars pressures. The research was conducted over a commercial BASF catalyst and a laboratory prepared catalyst. The catalyst has a content of different substances including basically NiO/Al2O3 and some additionals (Ca, Mg, Cr, Si). The experimental measurements were carried out within a recently developed experimental equipment which can be operated up to 1200o and 1 to 3 bars pressures. The study was conducted over a commercial BASF catalyst and a laboratory prepared catalyst under different ethanol/water ratios, temperatures, and catalyst loads. Under the condition when ethanol/water ratios were decreased from 1/2 to 1/10, it was observed that hydrogen ratios increased in exit gas composition of the reactor. With increments in catalyst loads from 1 to 5 grammes, hydrogen ratios in exit gas composition gradually increased. Reaction of ethanol-steam reforming started nearly at 300oC, and when temperature increments continued further up to 700oC, hydrogen yields in exit gas compositions of the reactor increased significantly to a range of 70% - 80%. In the case of using commercial BASF catalyst, hydrogen ratios in exit gas composition were found slightly higher than laboratory prepared catalyst. According to our observations, life time of laboratory prepared catalyst was found higher than the commercial BASF catalyst. In this study which kinetic measurements were applied, some kinetic parameters of ethanol-steam reaction were calculated. The mean activation energy of ethanol consumptions at 573oK - 973oK was found as 26.87 kJ/mol, approximately. All kinetic measurements were analyzed with a first order reaction rate model. In this study, some diffusion limitations existed, however, overall reaction was chemically controlled.

基于STEAM教育理念的“双高”院校跨界融合建设策略

为实现高职院校对学生综合素质的跨界培养,更好地满足区域经济快速发展对高技能人才的需求,在分析STEAM(Science,Technology,Engineering,Art,Mathematics)教育理念的本质与内涵,以及与高职院校“双高”建设目标契合点的基础上,探讨了“双高”院校跨界融合建设策略,提出高职院校在政府与社会各界的支持下实现开放办学,实施产教融合、学科融合、科教融合和科文融合,是推进“双高”院校高质量发展的可行路径。

New Trends in Olefin Production

Most olefins （e.g., ethylene and propylene） will continue to be produced through steam cracking （SC） ofhydrocarbons in the coming decade. In an uncertain commodity market, the chemical industry is investingvery little in alternative technologies and feedstocks because of their current lack of economic viability,despite decreasing crude oil reserves and the recognition of global warming. In this perspective, some of themost promising alternatives are compared with the conventional SC process, and the major bottlenecks ofeach of the competing processes are highlighted. These technologies emerge especially from the abundanceof cheap propane, ethane, and methane from shale gas and stranded gas. From an economic point of view,methane is an interesting starting material, if chemicals can be produced from it. The huge availability ofcrude oil and the expected substantial decline in the demand for fuels imply that the future for proventechnologies such as Fischer-Tropsch synthesis （FFS） or methanol to gasoline is not bright. The abundance ofcheap ethane and the large availability of crude oil, on the other hand, have caused the SC industry to shiftto these two extremes, making room for the on-purpose production of light olefins, such as by the catalyticdehydrogenation of orooane.

TiO2-based materials for photocatalytic hydrogen production

Hydrogen, the cleanest and most promising energy vector, can be produced by solar into chemical energy conversion, either by the photocatalytic direct splitting of water into Hand O, or, more efficiently,in the presence of sacrificial reagents, e.g., in the so-called photoreforming of organics. Efficient photocatalytic materials should not only be able to exploit solar radiation to produce electron–hole pairs, but also ensure enough charge separation to allow electron transfer reactions, leading to solar energy driven thermodynamically up-hill processes. Recent achievements of our research group in the development and testing of innovative TiO-based photocatalytic materials are presented here, together with an overview on the mechanistic aspects of water photosplitting and photoreforming of organics. Photocatalytic materials were either（i） obtained by surface modification of commercial photocatalysts, or produced（ii） in powder form by different techniques, including traditional sol gel synthesis, aiming at engineering their electronic structure, and flame spray pyrolysis starting from organic solutions of the precursors, or（iii） in integrated form, to produce photoelectrodes within devices, by radio frequency magnetron sputtering or by electrochemical growth of nanotube architectures, or photocatalytic membranes, by supersonic cluster beam deposition.

Hydrogen Production Technologies Overview

Hydrogen energy became the most significant energy as the current demand gradually starts to increase. Hydrogen energy is an important key solution to tackle the global temperature rise. The key important factor of hydrogen production is the hydrogen economy. Hydrogen production technologies are commercially available, while some of these technologies are still under development. This paper reviews the hydrogen production technologies from both fossil and non-fossil fuels such as (steam reforming, partial oxidation, auto thermal, pyrolysis, and plasma technology). Additionally, water electrolysis technology was reviewed. Water electrolysis can be combined with the renewable energy to get eco-friendly technology. Currently, the maximum hydrogen fuel productions were registered from the steam reforming, gasification, and partial oxidation technologies using fossil fuels. These technologies have different challenges such as the total energy consumption and carbon emissions to the environment are still too high. A novel non-fossil fuel method [ammonia NH3] for hydrogen production using plasma technology was reviewed. Ammonia decomposition using plasma technology without and with a catalyst to produce pure hydrogen was considered as compared case studies. It was showed that the efficiency of ammonia decomposition using the catalyst was higher than ammonia decomposition without the catalyst. The maximum hydrogen energy efficiency obtained from the developed ammonia decomposition system was 28.3% with a hydrogen purity of 99.99%. The development of ammonia decomposition processes is continues for hydrogen production, and it will likely become commercial and be used as a pure hydrogen energy source.

价值共创视角的工程类STEAM课程设计研究——以智能蜗牛饲养箱课程为例

旨在探索在工程类STEAM课程设计中的设计方法并进行设计实践。通过价值共创的视角对工程类STEAM课程的分析解析其共创机理,由价值矩阵将工程类STEAM课程价值生成过程理解为产品生成过程,提出产品作为核心线索的设计方法,并通过设计实践验证该设计方法可行性。提出基于产品生成逻辑的“建构-解构-再建构”的课程设计方法,能够有效把握STEAM内涵要求的基础上进行课程设计开发。以小学三年级科学课教材中的蜗牛一节内容作为出发点进行工程类STEAM课程设计实践,创造出智能蜗牛饲养箱STEAM课程。以此为过去经验性的课程设计开发方法厘清设计思路与路径,以期帮助STEAM教育的本土化发展。

An Experimental Investigation of Hydrogen Production from Biomass

In gaseous products of biomass steam gasification, there exist a lot of CO, CH4 and other hydrocarbons that can be converted to hydrogen through steam reforming reactions. There exists potential hydrogen production from the raw gas of biomass steam gasification. In the present work, the characteristics of hydrogen production from biomass steam gasification were investigated in a small-scale fluidized bed. In these experiments, the gasifying agent (air) was supplied into the reactor from the bottom of the reactor and the steam was added into the reactor above biomass feeding location. The effects of reaction temperature, steam to biomass ratio, equivalence ratio (ER) and biomass particle size on hydrogen yield and hydrogen yield potential were investigated. The experimental results showed that higher reactor temperature, proper ER, proper steam to biomass ratio and smaller biomass particle size will contribute to more hydrogen and potential hydrogen yield.

Improvement strategies for Ni-based alcohol steam reforming catalysts

Steam reforming(SR)of fossil methane is already a well-known,documented and established expertise in the industrial sector as it accounts for the vast majority of global hydrogen production.From a sustainable development perspective,hydrogen production by SR of biomass-derived feedstock represents a promising alternative that could help to lower the carbon footprint of the traditional process.In this regard,bio-alcohols such as methanol,ethanol or glycerol are among the attractive candidates that could serve as green hydrogen carriers as they decompose at relatively low temperatures in the presence of water compared to methane,allowing for improved H_(2)yields.However,significant challenges remain regarding the activity and stability of nickel-based catalysts,which are most widely used in alcohol SR processes due to their affordability and ability to break C–C,O–H and C–H bonds,yet are prone to rapid deactivation primarily caused by coke deposition and metal particle sintering.In this state-of-the-art review,a portfolio of strategies to improve the performance of Ni-based catalysts used in alcohol SR processes is unfolded with the intent of pinpointing the critical issues in catalyst development.Close examination of the literature reveals that the efforts tackling these recurring issues can be directed at the active metal,either by tuning Ni dispersion and Ni-support interactions or by targeting synergistic effects in bimetallic systems,while others focus on the support,either by modifying acid-base character,oxygen mobility,or by embedding Ni in specific crystallographic structures.This review provides a very useful tool to orient future work in catalyst development.