Current Strategies of Surface Modifications to Polyurethane Biomaterials for Vascular Grafts

As the number of patients suffering from cardiovascular diseases and peripheral vascular diseases rises,the constraints of autologous transplantation remain unavoidable.As a result,artificial vascular grafts must be developed.Adhesion of proteins,platelets and bacteria on implants can result in stenosis,thrombus formation,and postoperative infection,which can be fatal for an implantation.Polyurethane,as a commonly used biomaterial,has been modified in various ways to deal with the adhesions of proteins,platelets,and bacteria and to stimulate endothelium adhesion.In this review,we briefly summarize the mechanisms behind adhesions,overview the current strategies of surface modifications of polyurethane biomaterials used in vascular grafts,and highlight the challenges that need to be addressed in future studies,aiming to gain a more profound understanding of how to develop artificial polyurethane vascular grafts with an enhanced implantation success rate and reduced side effect.

Surface modifications of biometallic commercially pure Ti and Ti–13Nb–13Zr alloy by picosecond Nd:YAG laser

The effects of picosecond Nd:YAG laser irradiation on chemical and morphological surface characteristics of the commercially pure titanium and Ti–13Nb–13Zr alloy in air and argon atmospheres were studied under different laser output energy values.During the interaction of laser irradiation with the investigated materials,a part of the energy was absorbed on the target surface,influencing surface modifications.Laser beam interaction with the target surface resulted in various morphological alterations,resulting in crater formation and the presence of microcracks and hydrodynamic structures.Moreover,different chemical changes were induced on the target materials’surfaces,resulting in the titanium oxide formation in the irradiation-affected area and consequently increasing the irradiation energy absorption.Given the high energy absorption at the site of interaction,the dimensions of the surface damaged area increased.Consequently,surface roughness increased.The appearance of surface oxides also led to the increased material hardness in the surface-modified area.Observed chemical and morphological changes were pronounced after laser irradiation of the Ti–13Nb–13Zr alloy surface.

Influence of Different Surface Modifications on the Photovoltaic Performance and Dark Current of Dye-Sensitized Solar Cells

The TiO2 nanoporous film photoelectrode, as a crucial component of dye-sensitized solar cells, has been investigated. The photovoltaic properties and the dark current were studied by two surface modification methods. One was to apply a compact layer between the conductive glass substrate and nanoporous TiO2 film. Another was to produce TiO2 nanoparticles among the microstructure by TICl4 treatment. A suitable concentration and number of times for TICl4 treatment were found in our experiment. The dark current is suppressed by surface modifications, leading to a significant improvement in the solar cells performance. An excessive concentration of TICl4 will produce more surface states and introduce a larger dark current reversely. The dye is also regarded as a source of charge recombination in dark to some extent, due to an amount of surface protonations introduced by the interracial link in the conductive glass substrate/dye interface and dye/TiO2 interface.

Surface-modified Ag@Ru-P25 for photocatalytic CO_(2) conversion with high selectivity over CH_(4) formation at the solid–gas interface

Systematic optimization of the photocatalyst and investigation of the role of each component is important to maximizing catalytic activity and comprehending the photocatalytic conversion of CO_(2) reduction to solar fuels.A surface-modified Ag@Ru-P25 photocatalyst with H_(2)O_(2) treatment was designed in this study to convert CO_(2) and H_(2)O vapor into highly selective CH4.Ru doping followed by Ag nanoparticles(NPs)cocatalyst deposition on P25(TiO_(2))enhances visible light absorption and charge separation,whereas H_(2)O_(2) treatment modifies the surface of the photocatalyst with hydroxyl(–OH)groups and promotes CO_(2) adsorption.High-resonance transmission electron microscopy,X-ray photoelectron spectroscopy,X-ray absorption near-edge structure,and extended X-ray absorption fine structure techniques were used to analyze the surface and chemical composition of the photocatalyst,while thermogravimetric analysis,CO_(2) adsorption isotherm,and temperature programmed desorption study were performed to examine the significance of H_(2)O_(2) treatment in increasing CO_(2) reduction activity.The optimized Ag1.0@Ru1.0-P25 photocatalyst performed excellent CO_(2) reduction activity into CO,CH4,and C2H6 with a~95%selectivity of CH4,where the activity was~135 times higher than that of pristine TiO_(2)(P25).For the first time,this work explored the effect of H_(2)O_(2) treatment on the photocatalyst that dramatically increases CO_(2) reduction activity.

Influence of laser parameters on the microstructures and surface properties in laser surface modification of biomedical magnesium alloys

Biodegradable implants from magnesium(Mg)alloys have emerged in the biomedical field especially in the orthopedic and cardiovascular stent applications owing to their low density,high specific strength,excellent machinability,good biocompatibility,and biodegradability.The primary shortcoming of Mg-based implants is their low corrosion resistance in the physiological environment,which results in premature mechanical integrity loss before adequate healing and the production of excessive hydrogen gas,which is harmful to the body tissues and negatively affects the biocompatibility of the implant.Laser surface modification has recently received attention because it can improve the surface properties such as surface chemistry,roughness,topography,corrosion resistance,wear resistance,hydrophilicity,and thus cell response to the surface of the material.The composition and microstructures including textures and phases of laser-treated surfaces depend largely on the laser processing parameters(input laser power,laser scan velocity,frequency,pulse duration,pressure,gas circulation,working time,spot size,beam focal position,and laser track overlap)and the thermophysical properties of the substrate(solubility,melting point,and boiling point).This review investigates the impacts of various laser surface modification techniques including laser surface melting,laser surface alloying,laser cladding,laser surface texturing,and laser shock peening,and highlights their significance in improving the surface properties of biodegradable Mg alloys for implant applications.Additionally,we explore how different laser process parameters affect its composition,microstructure,and surface properties in each laser surface modification technique.

Effect of surface modification on the radiation stability of diamond ohmic contacts

The ohmic contact interface between diamond and metal is essential for the application of diamond detectors.Surface modification can significantly affect the contact performance and eliminate the interface polarization effect.However,the radiation stability of a diamond detector is also sensitive to surface modification.In this work,the influence of surface modification technology on a diamond ohmic contact under high-energy radiation was investigated.Before radiation,the specific contact resistivities(ρc)between Ti/Pt/Au-hydrogen-terminated diamond(H-diamond)and Ti/Pt/Au-oxygenterminated diamond(O-diamond)were 2.0×10^(-4)W·cm^(2) and 4.3×10^(-3)Wcm^(2),respectively.After 10 MeV electron radiation,the ρc of Ti/Pt/Au H-diamond and Ti/Pt/Au O-diamond were 5.3×10^(-3)W·cm^(2)and 9.1×10^(-3)W·cm^(2),respectively.The rates of change of ρc of H-diamond and O-diamond after radiation were 2550%and 112%,respectively.The electron radiation promotes bond reconstruction of the diamond surface,resulting in an increase in ρc.

Triple the steady-state reaction rate by decorating the In_(2)O_(3)surface with SiO_(x)for CO_(2)hydrogenation

Indium oxide(In_(2)O_(3)),as a promising candidate for CO_(2)hydrogenation to C_(1) products,often suffers from sintering and activity decline,closely related to the undesirable structural evolution under reaction conditions.Based on the comprehension of the dynamic evolution,this study presents an efficient strategy to alleviate the agglomeration of In_(2)O_(3)nanoparticles by the surface decoration with highly dispersed silica species(SiO_(x)).Various structural characterizations combined with density functional theory calculations demonstrated that the sintering resulted from the over-reduction,while the enhanced stability originated from the anchoring effect of highly stable In-OSi bonds,which hinders the substantial formation of metallic In(In^(0))and the subsequent agglomeration.0.6Si/In_(2)O_(3)exhibited CO_(2)conversion rate of10.0 mmol g^(-1)h^(-1)at steady state vs.3.5 mmol g^(-1)h^(-1)on In_(2)O_(3)in CO_(2)hydrogenation.Enhanced steady-state activity was also achieved on Pd-modified catalysts.Compared to the traditional Pd/In_(2)O_(3)catalyst,the methanol production rate of Pd catalyst supported on 0.6Si/In_(2)O_(3)was enhanced by 23%,showing the potential of In_(2)O_(3)modified by SiO_(x)in serving as a platform material.This work provides a promising method to design new In_(2)O_(3)-based catalysts with improved activity and stability in CO_(2)hydrogenation.

Microstructure and property modifications in surface layers of a Mg-4Sm-2Al-0.5Mn alloy induced by pulsed electron beam treatments

In this work,surface modification of a Mg-4Sm-2Al-0.5Mn alloy with high current pulse electron beam(HCPEB)under different number of pulses were investigated.The evolution in microstructure,composition and phase components and properties in the surface layer before and after HCPEB treatment were characterized.It was found that the Al 11 Sm 3 and Al 2 Sm phases in the surface layer were gradually dissolved during HCPEB treatment,leading to the formation of a chemical homogeneous melted layers.Besides,deformation bands were formed in the treated layer due to the thermal stress generated during treatment.After 15 pulses treatment,the surface hardness increases to the maximum value of about 62.2 HV,about 61.2%higher than that of the untreated state.Electrochemical results show that the 15 pulses treated sample presents the best corrosion resistance in the 3.5wt%NaCl water solution by showing the highest corrosion potential(E_(corr))of-1.339V SEC and the lowest corrosion current density(I_(corr))of 1.48×10^(-6)A·cm^(-2).The results prove that the surface properties of the Mg-4Sm-2Al-0.5Mn alloy can be significantly improved by the HCPEB treatments under proper conditions.

Effects of surface modifications on the physicochemical properties of iron oxide nanoparticles and their performance as anticancer drug carriers

The feature of the surface coating can affect important properties of iron oxide nanoparticles(IONPs), it is therefore critical for further understanding how these materials react to physiological conditions, which is still needed to fully exploit the potential of IONPs for their theranostic applications. In this work, we prepared IONPs which surface were modified with citric acid(CA), chitosan(CS) and folic acid conjugated chitosan(FA-g-CS). respectively. Their physicochemical properties were investigated using FT-IR, TEM,powder XRD, VSM, TGA, DLS and zeta potential. We found that CA-IONP dispersion was composed of monocrystalline particles while CS-IONP and FA-g-CS-IONP were composed of polycrystalline aggregates. All IONPs retained the crystalline structure of magnetite and exhibited the superparamagnetic behavior. Their saturation magnetization decreased with the increase in the amount of their organic coatings. Their drug loading capacities, drug release patterns and in vitro anticancer efficiencies were studied by using doxorubicin(DOX) as a model drug. DOX@CS-IONP and DOX@FA-g-CSIONP exhibited lower drug loading while showing higher water dispersity when compared with DOX@CA-IONP. All IONPs were surface charged and they tended to agglomerate in medium with high pH value and ionic strength. In the presence of chitosan or FA-g-CS coatings, their DOX release rate was slowed down compared with that of DOX@CA-IONP. Unloaded IONPs exhibited nearly no cytotoxicity on both cancer cells and normal cells in the presence of chitosan and FA-g-CS when compared with CA-IONP which presented high cytotoxicity. However, DOX@FA-g-CS-IONP showed significantly cytotoxicity on folate receptors(FRs) positive breast cancer cells while exhibiting nearly no cytotoxicity on FRs negative normal cells. Results presented in this study were valuable to the design and fabrication of IONPs-based system for better theranostic applications.

Recent Advances in Structural Optimization and Surface Modification on Current Collectors for High‑Performance Zinc Anode:Principles,Strategies,and Challenges

The last several years have witnessed the prosperous development of zinc-ion batteries(ZIBs),which are considered as a promising competitor of energy storage systems thanks to their low cost and high safety.However,the reversibility and availability of this system are blighted by problems such as uncontrollable dendritic growth,hydrogen evolution,and corrosion passivation on anode side.A functionally and structurally well-designed anode current collectors(CCs)is believed as a viable solution for those problems,with a lack of summarization according to its working mechanisms.Herein,this review focuses on the challenges of zinc anode and the mechanisms of modified anode CCs,which can be divided into zincophilic modification,structural design,and steering the preferred crystal facet orientation.The possible prospects and directions on zinc anode research and design are proposed at the end to hopefully promote the practical application of ZIBs.

A bi-functional strategy involving surface coating and subsurface gradient co-doping for enhanced cycle stability of LiCoO_(2) at 4.6 V

Layered LiCoO_(2)(LCO)acts as a dominant cathode material for lithium-ion batteries(LIBs)in 3C products because of its high compacted density and volumetric energy density.Although improving the high cutoff voltage is an effective strategy to increase its capacity,such behavior would trigger rapid capacity decay due to the surface or/and structure degradation.Herein,we propose a bi-functional surface strategy involving constructing a robust spinel-like phase coating layer with great integrity and compatibility to LiCoO_(2) and modulating crystal lattice by anion and cation gradient co-doping at the subsurface.As a result,the modified LiCoO_(2)(AFM-LCO)shows a capacity retention of 80.9%after 500 cycles between 3.0and 4.6 V.The Al,F,Mg enriched spinel-like phase coating layer serves as a robust physical barrier to effectively inhibit the undesired side reactions between the electrolyte and the cathode.Meanwhile,the Al,F,Mg gradient co-doping significantly enhances the surficial structure stability,suppresses Co dissolution and oxygen release,providing a stable path for Li-ions mobility all through the long-term cycles.Thus,the surface bi-functional strategy is an effective method to synergistically improve the electrochemical performances of LCO at a high cut-off voltage of 4.6 V.

Using pectin to separate talc and molybdenite through the surface modification with Cu^(2+):Applications and mechanism

Organic depressants have low selectivity in separating molybdenite and talc because their metal sites lack activity for organics chemisorption.In this study,surface modification by copper sulfate was used to induce the differential adsorption of pectin onto molybdenite and talc surfaces for enhanced flotation separation.Contact-angle experiments,scanning electron microscopy,adsorption measurements,timeof-flight secondary-ion mass spectrometry,and X-ray photoelectron spectroscopy analyses were conducted to reveal the interaction mechanism.Results illustrated that molybdenite and talc could not be separated using pectin alone,while molybdenite was selectively depressed after surface modification by copper sulfate and this effect was strengthened under alkaline conditions.Metal sites(Mg,Si and Mo)of talc and molybdenite themselves were unable to react with pectin,whereas Cu+would deposit and further function as active site for pectin chemisorption after surface modification.However,the quantity of deposited Cu sites dropped on talc surface and increased on molybdenite surface with increased pH,and the Mo atoms of molybdenite crystal were activated to take part in pectin chemisorption.Therefore,more pectin was adhered on molybdenite surface,which imparted molybdenite stronger wettability.Herein,surface-modification through metal ions can enable the differential adsorption of organic depressants and enhance the flotation separation of minerals.

A review on developing high-performance ZE41 magnesium alloy by using bulk deformation and surface modification methods

Magnesium(Mg)alloys are generally used in light-weight structural applications due to their higher specific strength.However,the usage of these Mg alloys is limited due to their poor formability at room temperature,which is attributed to lower count of slip systems associated with the hcp crystal structure.To address these limitations,several new magnesium alloys and also many processing strategies have been developed and reported in the literature.ZE41 Mg is an alloy with significant quantities of zinc(Zn)and rare earth(RE)elements and has emerged as a promising material for aerospace,automotive,electronics,biomedical and many other industries.To make this alloy more competitive and viable,it should possess better mechanical and corrosion properties.Hence,the current paper reviews the effect of bulk mechanical processing on grain refinement,microstructural modification,and corresponding changes in the mechanical behaviour of ZE41Mg alloy.Further,the effect of various surface modification techniques on altering the surface microstructure and surface properties such as wear and corrosion are also briefly summarized and presented.This review also discusses the challenges and the future perspectives in developing high-performing ZE41 Mg alloys.

Recent advances in surface endothelialization of the magnesium alloy stent materials

Magnesium and its alloy have good mechanical properties and biodegradability,and have become the hotspot of the next-generation biodegradable vascular stent materials.However,their rapid degradation in vivo and poor biocompatibility are still the bottlenecks of clinical applications for the cardiovascular stents.In particular,how to induce the repair and regeneration of the vascular endothelial with normal physiological functions on the surface of the magnesium alloy stent materials represents the key to its clinical application in the field of cardiovascular stents.It has been believed that it is an ideal way to completely solve the postoperative complications through constructing the multifunctional anti-corrosive bioactive coating on the magnesium alloy surface to induce the formation of vascular endothelium with normal physiological functions.However,how to construct a corrosion-resistant multifunctional bioactive coating with the good endothelial regeneration abilities on the magnesium alloy surface still faces a great challenge.This paper mainly focused on highlighting and summarizing the recent advances in the surface endothelialization of the magnesium alloy materials for the vascular stent,including the bio-inert coating,in-situ immobilization of bioactive molecules on the surface,polymer coating loaded with bioactive factors,novel multifunctional polymer coating,bioactive micropatterns,bioactive layer with glycocalyx-like structure,NO-releasing coating and bioactive sol-gel coating.The advantages and disadvantages of these strategies were discussed and analyzed.Finally,in the senses of future development and clinical application,this paper analyzed and summarized the development direction and prospect of surface endothelialization of the magnesium alloy vascular stents.It is anticipated that this review can give the new cues to the surface endothelialization of the cardiovascular magnesium alloy stents and promote future advancements in this field.

Marine antifouling behavior of the surfaces modified by dopamine and antibacterial peptide

Marine biofouling causes serious harms to surfaces of marine devices in transportation,aquaculture,and offshore construction.Traditional antifouling methods pollute the environment.A novel and green antifouling strategy was developed to prevent effectively the adhe sion of bacteria and microalgae.An antifouling surface was fabricated via coating Turgencin BMox2(TB)onto dopamine-modified 304stainless steel(304 SS).The surface physical and chemical properties before and after modification were characterized by Fourier transform infrared spectrometer(FTIR),X-ray photoelectron spectrometer(XPS),contact angle measurement(CA),3D optical profilometer,ellipsometer,and atomic force microscope(AFM).Antimicrobial peptide was coated onto the surface of 304 SS successfully,and the surface morphology and wettability of the modified sample were modified.Moreover,cytocompatibility of the peptide was evaluated by co-culture of peptide and cells,indicating promising cell biocompatibility at the modified sample surface.At last,antifouling performance and electrochemical corrosion were tested.Results show that the adhesion rates of Vibrio natriegens and Phaeodactylum tricornutum on the antifouling surface were reduced by 99.85% and 67.93%,respectively from those of untreated samples.Therefore,the modified samples retained superior corrosion resistance.The study provide a simply and green way against biofouling on ship hulls and marine equipment.

Surface hydrophobic modification of MXene to promote the electrochemical conversion of N_(2) to NH_(3)

Hydrophobic treatment of the catalyst surfaces can suppress the competitive hydrogen evolution reaction(HER) during the nitrogen reduction reaction(NRR).In this work,the surface of Ti_(3)C_(2)Ti_(x) MXene is modified by cetyltrimethylammonium bromide(CTAB) and trimethoxy(3,3,4,4,5,5,6,6,7,7,8,8,8-trideca fluorooctyl) silane(FOTS) to increase the hydrophobicity of MXenes.The ammonia(NH_(3)) production rate and faradaic efficiency(FE) are improved from 37.62 to 54.01 μg h^(-1)mg_(cat)^(-1).and 5.5% to 18.1% at-0.7 V vs.RHE,respectively after surface modification.^(15)N isotopic labeling experiment confirms that nitrogen in produced ammonia originates from N_(2) in the electrolyte.The excellent NRR activity of surface hydrophobic MXenes is mainly due to surfactant molecules,which inhibit the entry of water molecules and the competitive HER,which have been verified by in situ FT-IR,DFT and molecular dynamics calculations.This strategy provides an ingenious method to design more active NRR electrocatalysts.

Fatigue crack propagation of 7050 aluminum alloy FSW joints after surface peening

The surface composite modification of the 7050 aluminum alloy friction stir-welded joints was performed by shot peening(SP)/multiple rotation rolling(MRR)and MRR/SP,and the fatigue performance of the nugget zone(NZ)was investigated.The results demonstrated that the fatigue life of SP/MRR samples is longer than that of MRR/SP.On the plane 150μm below the surface.The grains with high angle grain boundary account for 71.5%and 34.3%for MRR/SP and SP/MRR samples,respectively.The crack propagation path of the MRR/SP is transgranular and intergranular,and it is intergranular for the MRR/SP.Multitudinous fatigue striations and some voids appeared at the fracture during the stable crack propagation stage.However,fatigue striations for SP/MRR are with smaller spacing,fewer holes,and smaller size under SP/MRR compared with fatigue fracture of MRR/SP.The differences in fatigue properties and fracture characteristics of the NZ are related to the microstructure after the two combined surface modifications.

Chemical surface tuning of zinc metal anode toward stable,dendrite-less aqueous zinc-ion batteries

The commercialization of Zn batteries is confronted with urgent challenges in the metal anode,such as dendrite formation,capacity loss,and cracking or dissolution.Here,surface interfacial engineering of the Zn anode is introduced for achieving safety and dendritic-free cycling for high-performance aqueous Zn batteries through a simple but highly effective chemical etching-substitution method.The chemical modification induces a rough peak-valley surface with a thin fluorine-rich interfacial layer on the Zn anode surface,which regulates the growth orientation via guiding uniform Zn plating/stripping,significantly enhances accessibility to aqueous electrolytes and improves wettability by reducing surface energy.As a result,such a synergetic surface effect enables uniform Zn plating/stripping with low polarization of 29 m V at a current density of 0.5 m A cm^(-2) with stable cyclic performance up to 1000 h.Further,a full cell composed of a fluorine-substituted Zn anode coupled with aβ-MnO_(2)or Ba-V_(6)O_(13)cathode demonstrates improved capacity retention to 1000 cycles compared to the pristine-Zn cells.The proposed valley deposition model provides the practical direction of surface-modified interfacial chemistries for improving the electrochemical properties of multivalent metal anodes via surface tuning.

Surface modification of CeO_(2-x) nanorods with Sn doping for enhanced nitrogen electroreduction

While the electrochemical nitrogen reduction reaction(NRR) represents a prospective blueprint for environmentally renewable ammonia generation,it has yet to overcome the limitations of weak activity and inferior selectivity.In this regard,surface modification tactic was constructed to markedly enhance the activity and selectivity via introducing Sn atoms into the surface of defective cerium oxide(denoted as Sn-CeO_(2-x)) as the active and robust electrocatalyst for NRR under benign environment.The introduction of Sn atoms in CeO_(2-x)can not only inhibit the HER activity of the catalyst but also modulate the electronic structure of ceria and optimize N-Ce interaction,thus enhancing NRR activity and selectivity.Outperforming all previous CeO_(2)-based NRR catalysts,this catalyst has demonstrated an ammonia yield rate of 41.1 μg mg_(cat)^(-1) h^(-1) and an exceptional Faradic efficiency of 35.3%.This work presents a viable approach for the development of advanced NRR electrocatalysts.

All-organic modification coating prepared with large-scale atmospheric-pressure plasma for mitigating surface charge accumulation

The surface charge accumulation on polymers often leads to surface flashover.Current solutions are mainly based on the introduction of inorganic fillers.The high-cost process and low compatibility remain formidable challenges.Moreover,existing researches on all-organic insulation focus on capturing electrons,contrary to alleviating charge accumulation.Here,an all-organic modification coating was prepared on polystyrene(PS)with the large-scale atmospheric-pressure plasma,which exhibits outperformed function in mitigating surface charge accumulation.The surface charge dissipation rate and surface conductivity are promoted by about 1.37 and 9.45 times,respectively.Simulation and experimental results show that this all-organic modification coating has a smaller electron affinity potential compared with PS.The decrease of electron affinity potential may result in accelerated surface charge decay of PS,which has never been involved in previous works.Moreover,this coating also has good reliability in a repeated surface flashover.This facile and large-scale approach brings up a novel idea for surface charge regulation and the manufacture of advanced dielectric polymers.