Variation in the surface heat flux on the north and south slopes of Mount Qomolangma

The distinctive conditions present on the north and south slopes of Mount Qomolangma,along with the intricate variations in the underlying surfaces,result in notable variations in the surface energy flux patterns of the two slopes.In this paper,data from TESEBS(Topographical Enhanced Surface Energy Balance System),remote sensing data from eight cloud-free scenarios,and observational data from nine stations are utilized to examine the fluctuations in the surface heat flux on both slopes.The inclusion of MCD43A3 satellite data enhances the surface albedo,contributing to more accurate simulation outcomes.The model results are validated using observational data.The RMSEs of the net radiation,ground heat,sensible heat,and latent heat flux are 40.73,17.09,33.26,and 30.91 W m^(−2),respectively.The net radiation flux is greater on the south slope and exhibits a rapid decline from summer to autumn.Due to the influence of the monsoon,on the north slope,the maximum sensible heat flux occurs in the pre-monsoon period in summer and the maximum latent heat flux occurs during the monsoon.The south slope experiences the highest latent heat flux in summer.The dominant flux on the north slope is sensible heat,while it is latent heat on the south slope.The seasonal variations in the ground heat flux are more pronounced on the south slope than on the north slope.Except in summer,the ground heat flux on the north slope surpasses that on the south slope.

CALCULATION OF THREE－DIMENSIONAL SOLDER JOINT FORMATION IN MICROELECTRONIC SURFACE MOUNT TECHNOLOGY

A finite element analysis for calculating three-dimensional(3-D) solder joint shape between chip component and substrate pad was carried out, and the effects of solder volume and pad extension beyond the edge of component on solder joint shapes were investigated. The resonable design ranges of solder volume and pad extension have been put forward.

Review on the Fabrication of Surface Functional Structures for Enhancing Bioactivity of Titanium and Titanium Alloy Implants

Titanium and its alloys have been widely applied in many biomedical fields because of its excellent mechanical properties,corrosion resistance and good biocompatibility.However,problems such as rejection,shedding and infection will occur after titanium alloy implantation due to the low biological activity of titanium alloy surface.The structures with specific functions,which can enhance osseointegration and antibacterial properties,are fabricated on the surface of titanium implants to improve the biological activity between the titanium implants and human tissues.This paper presents a comprehensive review of recent developments and applications of surface functional structure in titanium and titanium alloy implants.The applications of surface functional structure on different titanium and titanium alloy implants are introduced,and their manufacturing technologies are summarized and compared.Furthermore,the fabrication of various surface functional structures used for titanium and titanium alloy implants is reviewed and analyzed in detail.Finally,the challenges affecting the development of surface functional structures applied in titanium and titanium alloy implants are outlined,and recommendations for future research are presented.

KEY TECHNOLOGY OF SEMI-CONTINOUS CONVEYOR SYSTEM IN DEEP SURFACE MINE

The key technology of semi-continuous conveyor system decides the successful using of this system. The key technology includes optimal initial building depth of this system,the crusher moving step and the layout of conveyor system are studied, and their calculating models are built up.

Structural Surface Crack Monitoring Method Based on Electrical Potential Technique and Modern Surface Technology

Crack monitoring plays a great role in modern structural health monitoring, however, most of the conventional crack inspections have disadvantages in terms of the accuracy, expense, reliability, durability and level of instrumentation required. Thus, development of a simple and reliable crack inspection technique that allows continuous monitoring has been desired. In this paper, electrical potential technique and modern surface technology are employed together to develop a new structural surface crack monitoring method. A special crack monitoring coating sensor based on electrical potential technique was deposited on the hot spot of the structure by modern surface technology. The sensor consists of three layers： the isolated layer, the sensing layer and the protective layer. The isolated layer is prepared by anodic oxidation technology, the sensing layer is made of ion plated copper, and the protective layer is made of silicone. The thickness of each layer is at micrometer magnitude. The electrical conductivity of the sensor is very stable, and the fatigue performance of the specimen with or without coating sensor is nearly unchanged. The crack monitoring experiment result shows that there are two sudden rises of the coating sensor electrical potential values, corresponding to different stages of the crack initiation and propagation. Since the width of the surface coating sensor is only 0.5 mm, this crack monitoring sensor can detect the propagation of cracks less than 0.5 mm long. The method proposed takes the simplicity of electrical potential technique and can monitor surface crack of nearly all kinds of structures precisely. The results of this paper may form the basis of a new crack monitoring system.

The Fabrication of Microstructure Surface of Superhydrophobic Coating by Surface Gelation Technology

The microstructured surface of materials were fabricated by a two-step acid-base catalyzed sol-gel process. In fluorinated polymer with PTFE doping, the well-proportioned composite sols were prepared using sol-gel processing under the hydrochloric acid and deficiency of water conditions. After the substrate was coated by composite sols, and the gelation treatment on the surface of composite coating, the micrometer-scale and nanometer-scale hierarchical structures were formed in surface layer of material. XPS and TEM technologies were employed to identify that the gelation occurs just on the surface of composite coating. The morphology of coating surface was observed by SEM and AFM technologies. The microstructured surface of material can be fabricated using this inexpensive and easily controlled method on low surface energy resin materials, the super-hydrophobic coatings materials can be prepared.

Fatigue life prediction of workpiece with 3D rough surface topography based on surface reconstruction technology

The fatigue performance of a workpiece depends on its surface quality.In traditional fatigue life prediction,the effect of surface quality is commonly accounted for by using empirical correction factors,which is imprecise when safety is of great concern.For surface quality,the surface topography is an important parameter,which introduces stress concentration that reduces the fatigue life.It is not feasible to test the stress concentration of different surface topographies.On the one hand,it is time-consuming and high-cost,and on the other hand,it cannot reflect the general statistical characteristics.With the help of surface reconstruction technology and interpolation method,a more efficient and economic approach is proposed,where FE simulation of workpiece with the reconstructed surface topography is used as a foundation for fatigue life prediction.The relationship between surface roughness(Sa)and fatigue life of the workpiece is studied with the proposed approach.

Hierarchical planning for a surface mounting machine placement

For a surface mounting machine (SMM) in printed circuit board (PCB) assembly line, there are four problems, e.g. CAD data conversion, nozzle selection, feeder assignment and placement sequence determination. A hierarchical planning for them to maximize the throughput rate of an SMM is presented here. To minimize set-up time, a CAD data conversion system was first applied that could automatically generate the data for machine placement from CAD design data files. Then an effective nozzle selection approach was implemented to minimize the time of nozzle changing. And then, to minimize picking time, an algorithm for feeder assignment was used to make picking multiple components simultaneously as much as possible. Finally, in order to shorten pick-and-place time, a heuristic algorithm was used to determine optimal component placement sequence according to the decided feeder positions. Experiments were conducted on a four head SMM. The experimental results were used to analyse the assembly line performance.

Analytical calculation of electromagnetic, torque for surface mounted permanent magnet brushless motors

With the air gap magnetic field distribution of surface mounted permanent magnet （PM） motors obtained using an analytical technique, the instantaneous electromagnetic torque and its corresponding components are investigated with the Maxwell stress tensor method. Accurate results can easily be achieved using the proposed method without using the tedious finite element analysis （FEA）. In this paper, the electromagnetic torque of a surface mounted PM motor with two phases energized is decomposed into four torque components. This technique is useful not only for the design and optimization of the permanent magnet motor, but also for the choice of control strategy.

Finite element simulation for mechanical response of surface mounted solder joints under different temperature cycling

Nonlinear finite element simulation for mechanical response of surface mounted solder joint under different temperature cycling was carried out. Seven sets of parameters were used in order to evaluate the influence of temperature cycling profile parameters. The results show that temperature cycling history has significant effect on the stress response of the solder joint. Based on the concept of relative damage stress proposed by the authors, it is found that enough high temperature holding time is necessary for designing the temperature cycling profile in accelerated thermal fatigue test.

Response Surface Optimization for Process Parameters of LiFePO_4/C Preparation by Carbothermal Reduction Technology

A statistically based optimization strategy is used to optimize the carbothermal reduction technology for the synthesis of LiFePO4/C using LiOH,FePO4 and sucrose as raw materials.The experimental data for fitting the response are collected by the central composite rotatable design(CCD).A second order model for the discharge ca-pacity of LiFePO4/C is expressed as a function of sintering temperature,sintering time and carbon content.The ef-fects of individual variables and their interactions are studied by a statistical analysis(ANOVA).The results show that the linear effects and the quadratic effects of sintering temperature,carbon content and the interactions among these variables are statistically significant,while those effects of sintering time are insignificant.Response surface plots for spatial representation of the model illustrate that the discharge capacity depends on sintering temperature and carbon content more than sintering time.The model obtained gives the optimized reaction parameters of sinter-ing temperature at 652.0 ℃,carbon content of 34.33 g?mol-1 and 8.48 h sintering time,corresponding to a dis-charge capacity of 150.8 mA·h·g-1.The confirmatory test with these optimum parameters gives the discharge ca-pacity of 147.2 and 105.1 mA·h·g-1 at 0.5 and 5 C,respectively.

Investigation of the processing technology and mechanism of Kansui radix by licorice based on response surface methodology and integrative pharmacology

Background:The herbs should be processed by different methods before use,and the efficacy and toxicity of Chinese herbal medicines may change,which may enhance efficacy and reduce toxicity after processing.Gansui(Kansui radix)is a common clinical herbal medicine,and there are considerable changes in its toxicity and efficacy after processing.Gaocao(Glycyrrhizae radix et rhizome)has a detoxifying effect.Methods:Using the contents of euphorbiadienol and the alcohol-soluble extract of Glycyrrhizae radix-processed Kansui radix as evaluation indexes,response surface methodology was used to optimize the processing technology of Kansui radix by exploring the effects of Glycyrrhizae radix et rhizoma-addition amount,frying temperature,and frying time on the processing technology of Kansui radix.Meanwhile,response surface software was used to analyze experimental data to determine the processing parameters of Kansui radix by Glycyrrhizae radix et rhizoma.Integrative Pharmacology-based Research Platform of Traditional Chinese Medicine is used to analysis the potential ingredients of Kansui radix and verify the potential ingredients by western blotting.Results:The technology of Glycyrrhizae radix et rhizoma-processed Kansui radix was optimized for the Glycyrrhizae radix et rhizoma-addition amount of 27%,frying temperature of 180℃,and frying time of 11 min.The network pharmacology analysis revealed that Kansui radix could cause kidney,liver,and heart injury by the PI3K/AKT signaling pathway.Kansui radix at high or low dose could decrease the ratio of p-AKT/AKT while Glycyrrhizae radix et rhizoma-processed Kansui could increase it.Conclusion:The model established by response surface methodology is relatively accurate and can predict the contents of euphorbiadienol and alcohol extract of processed Kansui radix.The toxic effects and its mechanism of action of Kansui radix and processed Kansui radix on kidney,liver,and heart,from the perspective of systems biology,have provided scientific evidence to its clinical application.

Optimization of Enzyme-assisted Extraction Technology for Tartary Buckwheat Shell Procyanidins with Response Surface Methodology

This study was conducted to investigate the effects of cellulase dosage, enzymolysis time, pH and enzymolysis temperature on procyanidin extraction rate by single factor experiment, with tartary buckwheat shell as an experimental material.Main process parameters were optimized to obtain a regression model by response surface methodology. The results of variance analysis indicated that the regression model reflected the relationship between buckwheat shell procyanidin extraction rate with enzyme dosage, enzymolysis time, pH and enzymolysis temperature; and the optimal process parameters were enzyme dosage of 6.5 mg/g, enzymolysis time of 1.5 h, pH at 4.7 and enzymolysis temperature at 46 ℃. Three parallel experiments were conducted under these process parameters. In practice, the highest procyanidin extraction rate was 6.78 g/100 g. The relative error between the predicted value of regression model and the actual value was 1.3%. The regression equation fitted the real situation better.

Study on surfce mount technology for fine pitch L type lead devices

Problems about surface mounting process for fine pitch devices and reasons on solder bridging of L type lead devices welded are depicted. Bridging mechanism and influence factors are analyzed with two-dimensional geometric model. Based on this, high-density surface mount technology ( SMT) for fine pitch L type lead devices heated by scanning laser is raised. Surface mount process for QFP208 on printed circuit board (PCB) is studied. The results of tests are that it is quite possible to solve the solder bridging of surface mounting for fine pitch devices with scanning laser-heating method.

Quasi-plane-hypothesis of strain coordination for RC beams seismically strengthened with externally-bonded or near-surface mounted fiber reinforced plastic

The application of fiber reinforced plastic（FRP）,including carbon FRP and glass FRP,for structural repair and strengthening has grown due to their numerous advantages over conventional materials such as externally bonded reinforcement（EBR） and near-surface mounted（NSM） strengthening techniques.This paper summarizes the results from 21 reinforced concrete beams strengthened with different methods,including externally-bonded and near-surface mounted FRP,to study the strain coordination of the FRP and steel rebar of the RC beam.Since there is relative slipping between the RC beam and the FRP,the strain of the FRP and steel rebar of the RC beam satisfy the quasi-plane-hypothesis;that is,the strain of the longitudinal fiber that parallels the neutral axis of the plated beam within the scope of the effective height（h 0） of the cross section is in direct proportion to the distance from the fiber to the neutral axis.The strain of the FRP and steel rebar satisfies the equation：ε FRP =βε steel,and the value of β is equal to 1.1-1.3 according to the test results.

Reliability Theory Study of Combined Mining Technology System in Surface Mines

The connection between all the single systems iu combined technology is analysed, and the mine engineering reliability is calculated in any area of the mines using combined technololgy system. The reliability design and distribution method in this system is put forward, thus the basis is set for the decision to raise the total production capability or the surface mines in which the combined system is used.

A Study of Multi-Permeating TiN/Ti Alloying Layer Using Plasma Surface Alloying Technology

TiN/Ti multi-permeating alloying layer has been formed on the low carbon steel by means of the double glow-discharge plasma surface alloying technique and hollow-cathode effect. The alloying layer was detected by axiovert 25 CA optical microscope with computer analyzing software （LEC）, GDA-2 glow discharge spectroscopy （GDS）, X-ray diffraction （XRD） and galvanochemical method. The results showed that the thickness of TiN/Ti multi-permeating alloying layer was about 10μm, the content of Ti on the surface was up to 63.48 wt% and the content of N was up to 12.46 wt%. The atom Ti and N concentrations changed gradually across the depth of the alloying layer and the preferred orientation of TiN/Ti alloying layer was crystal surface （200）. The multi-permeating alloying layer and substrate were combined through metallurgy. The surface appearances of the multi-permeating alloying layer were uniform and of a compact cellular structure. The hardness of the surface was about 1600-3000 HV0.1. The corrosion resistance of the permeating TiN/Ti alloying layer in 0.5 mol/L H2SO4 solution was greatly increased and the corrosion rate was only 0.3082 g/m^2. h.

Research on development of surface-roughness variation and control technology of the automotive plates and rolls

Surface roughness considerably influences the stamping and coating performance of the automotive plates;however,the surface roughness of the automotive plates is transferred from the roll during the rolling process.Therefore,the variation and control technology regarding the roughness of the automotive plates and rolls has drawn increasing attention from researchers in China and around the globe.In this study,the research methods,analytical techniques,prediction models,transfer rules,and control technologies regarding the surface roughness of the automotive plates and rolls were reviewed.Among these,an online measurement system for automotive-plate and roll surface roughness has been applied to the production lines of Germany,China,Belgium,Holland,Austria,and other countries and has achieved remarkable results.Online measurement and timely feedback regarding the automotive-plate and roll surface roughness are needed to ensure favorable conditions for the establishment of automotive-plate roughness-control measurement.

Using Isotope Technology for Surface Water Environment Research in Southern Hanoi

The surface water in the southern of Hanoi capital is researched by identifying δ2H and δ18O stable isotopes together with EC, DO, BOD5, COD, TSS. Surface water samples for studying include the Red river, Nhue river and Kim Nguu river, Thanh Nhan lake, Yen So lake and Van Quan lake were collected in the dry season (April) and the rainy season (August) in 2015. The stable isotope analysis results showed that the δ18O values is a range from -42.53‰ to -64.05‰ and, the δ2H values is the range from -5.09‰ to -8.79‰ under global meteoric waterline (in the water vapor region). The δ2H results of the rivers and lakes in the dry season are more negative than the rainy season with a small difference. The δ18O results of lakes in the dry season are more negative than the rainy season, but the δ18O results of river in the dry season are more positive than the rainy season. The results of the EC, BOD, COD, DO, TSS analysis showed that surface water environment has changed clearly in the two seasons and the contamination level in the dry season is usually higher than the rainy season. The lakes and rivers strongly influenced by human activities led to seriously pollution are Van Quan lake and Yen So lake, Nhue river and Kim Nguu river.

Application of High-Resolution Remote Sensing Technology in Quantitative Study on Coseismic Surface Rupture Zones: An Example of the 2008 M_w7.2 Yutian Earthquake

Objective Nowadays, high-resolution remote sensing technology has brought new changes to surveys of earthquakes, and the quantitative study of seismic faults based on this technology has become a trend in the world(Barzegari et al., 2017). An Mw 7.2 earthquake occurred in Yutian of Xinjiang on the western end of the Altyn Tagh fault on March 21 st, 2008. It is difficult to access this depopulated zone because of the high altitude and only 1–2 months of snowmelt. This study utilized high-resolution