Precipitates Generation Mechanism and Surface Quality Improvement for Aluminum Alloy 6061 in Diamond Cutting

To improve the surface quality for aluminum alloy 6061(Al6061) in ultra-precision machining, we investigated the factors affecting the surface finish in single point diamond turning(SPDT)by studying influence of the precipitates generation of Al6061 on surface integrity and surface roughness.Based on the Johnson-Mehl-Avrami solid phase transformation kinetics equation, theoretical and experimental studies were conducted to build the relationship between the aging condition and the type, size and number of the precipitates for Al6061. Diamond cutting experiments were conducted to machine Al6061 samples under different aging conditions. The experimental results show that, the protruding on the chip surface is mainly Mg_(2)Si and the scratches on the machined surface mostly come from the iron-containing phase(α-, β-AlFeSi).Moreover, the generated Mg_(2)Si and α-, β-AlFeSi affect the surface integrity and the diamond turned surface roughness. Especially, the achieved surface roughness in SPDT is consistent with the variation of the number of AlFeSi and Mg_(2)Si with the medium size(more than 1 μm and less than 2 μm) in Al6061.

Theoretical Modeling and Surface Roughness Prediction of Microtextured Surfaces in Ultrasonic Vibration-Assisted Milling

Textured surfaces with certain micro/nano structures have been proven to possess some advanced functions,such as reducing friction,improving wear and increasing wettability.Accurate prediction of micro/nano surface textures is of great significance for the design,fabrication and application of functional textured surfaces.In this paper,based on the kinematic analysis of cutter teeth,the discretization of ultrasonic machining process,transformation method of coordinate systems and the cubic spline data interpolation,an integrated theoretical model was established to characterize the distribution and geometric features of micro textures on the surfaces machined by different types of ultrasonic vibration-assisted milling(UVAM).Based on the theoretical model,the effect of key process parameters(vibration directions,vibration dimensions,cutting parameters and vibration parameters)on tool trajectories and microtextured surface morphology in UVAM is investigated.Besides,the effect of phase difference on the elliptical shape in 2D/3D ultrasonic elliptical vibration-assisted milling(UEVAM)was analyzed.Compared to conventional numerical models,the method of the cubic spline data interpolation is applied to the simulation of microtextured surface morphology in UVAM,which is more suitable for characterizing the morphological features of microtextured surfaces than traditional methods due to the presence of numerous micro textures.The prediction of surface roughness indicates that the magnitude of ultrasonic amplitude in z-direction should be strictly limited in 1D rotary UVAM,2D and 3D UEVAM due to the unfavorable effect of axial ultrasonic vibration on the surface quality.This study can provide theoretical guidance for the design and fabrication of microtextured surfaces in UVAM.

Mechanical properties and fracture surface roughness of thermally damaged granite under dynamic splitting

In order to understand the mechanical properties and the fracture surface roughness characteristics of thermally damaged granite under dynamic splitting,dynamic Brazilian splitting tests were conducted on granite samples after thermal treatment at 25,200,400,and 600℃.Results show that the dynamic peak splitting strength of thermally damaged granite samples increases with increasing strain rate,showing obvious strain‐rate sensitivity.With increasing temperature,thermally induced cracks in granite transform from intergranular cracks to intragranular cracks,and to a transgranular crack network.Thermally induced damages reduce the dynamic peak splitting strength and the maximum absorbed energy while increasing the peak radial strain.The fracture mode of the thermally damaged granite under dynamic loads is mode Ⅱ splitting failure.By using the axial roughness index Z2 a,the distribution ranges of the wedge‐shaped failure zones and the tensile failure zones in the fracture surfaces under dynamic Brazilian splitting can be effectively identified.The radial roughness index Z_(2)^(r)is sensitive to the strain rate and temperature.It shows a linear correlation with the peak splitting strength and the maximum absorbed energy and a linear negative correlation with the peak radial strain.Z_(2)^(r)can be used to quantitatively estimate the dynamic parameters based on the models proposed.

High-order Bragg forward scattering and frequency shift of low-frequency underwater acoustic field by moving rough sea surface

Acoustic scattering modulation caused by an undulating sea surface on the space-time dimension seriously affects underwater detection and target recognition.Herein,underwater acoustic scattering modulation from a moving rough sea surface is studied based on integral equation and parabolic equation.And with the principles of grating and constructive interference,the mechanism of this acoustic scattering modulation is explained.The periodicity of the interference of moving rough sea surface will lead to the interference of the scattering field at a series of discrete angles,which will form comb-like and frequency-shift characteristics on the intensity and the frequency spectrum of the acoustic scattering field,respectively,which is a high-order Bragg scattering phenomenon.Unlike the conventional Doppler effect,the frequency shifts of the Bragg scattering phenomenon are multiples of the undulating sea surface frequency and are independent of the incident sound wave frequency.Therefore,even if a low-frequency underwater acoustic field is incident,it will produce obvious frequency shifts.Moreover,under the action of ideal sinusoidal waves,swells,fully grown wind waves,unsteady wind waves,or mixed waves,different moving rough sea surfaces create different acoustic scattering processes and possess different frequency shift characteristics.For the swell wave,which tends to be a single harmonic wave,the moving rough sea surface produces more obvious high-order scattering and frequency shifts.The same phenomena are observed on the sea surface under fully grown wind waves,however,the frequency shift slightly offsets the multiple peak frequencies of the wind wave spectrum.Comparing with the swell and fully-grown wind waves,the acoustic scattering and frequency shift are not obvious for the sea surface under unsteady wind waves.

Effect of Surface Roughness on Lubrication Performance of Bump-Type Gas Foil Bearings

Taking bump-type gas foil bearings as the research object,a deformation model of bump foil and a thin-plate finite element model of top foil were proposed.By solving Reynolds equation and energy equation,the pressure distribution and the temperature distribution of gas films in foil bearings were obtained.Further,a numerical method for calculating the lubrication performance of gas foil bearings with considering the surface roughness was proposed.With a specific example,effects of the surface roughness on the bearing lubrication performance were parametrically studied.The results indicate that rougher journal surface can lead to larger fluctuation of the lubrication performance,while surface roughness of top foil has few effects on the fluctuation.Moreover,the mean values of performance parameters almost remain constant at different values of surface roughness.

Impact of surface roughness,surface charge,and temperature on sandstone wettability alteration by nanoparticles

The wettability of rocks affects the balance between capillary and viscous forces during multiphase flow through porous media,which in turn determines the fluid displacement process governing the recovery of oil from subsurface formations.In this work,the mechanism of wettability reversal of aged synthetic sandstones by metal oxide nanoparticles(SiO_(2) and Al_(2)O_(3))was investigated with particular focus on the impact of surface roughness,zeta potential,and temperature.The synthetic surfaces were prepared from powders of Berea sandstone with known grain size ranges and their average roughness and roughness ratio were obtained from the 3D surface reconstruction of their microscope images.Each surface was subsequently aged in Permian crude oil to alter its wettability.For surfaces with larger grain sizes and lower surface roughness ratios,the lower capillary pressure allowed stronger oil/surface interactions,leading to enhanced oil-wetness.The wettability alteration effects of nanoparticles were then examined through real-time top view imaging and dynamic front view contact angle experiments.The negatively charged SiO_(2) nanoparticles rapidly reversed the sandstone wettability,indicating their potential applicability as wettability alteration agents.By contrast,the positively charged Al_(2)O_(3) counterpart caused no wettability reversal.The mechanism of wettability alteration was further studied by microscale interaction analyses and nanoscale transmission electron microscopy.Because nanoparticles were only a few nanometers large,the microscale roughness had a negligible effect on the wettability reversal.Instead,the combined effect of van der Waals dispersion forces and surface-charge-induced electrostatic forces were recognized as the two key factors affecting the wettability of sandstone particles.Such interactions may be curbed at elevated temperatures due to a decrease in the zeta potential and colloidal stability of the particles.

Assessments of the effects of various fracture surface morphology on single fracture flow: A review

Natural rock joint permeability deviates from the classic fluid flow governing equations due to the inher-ent fracture surface roughness(i.e.,contact points,spatial correlation,matching,varying aperture,iso-lated voids,infilling material,tortuosity and channellings)and engineering disturbance such as excavations.To improve the accuracy of fracture permeability evaluation,many efforts have been made in analytical,experimental,and numerical methods.This study reviews the modified mathematical gov-erning equations of fluid flow and classifies them based on different influencing factors,such as friction factor,aperture,tortuosity,inertia,and various in situ stress effects.Various experimental and simulation techniques for the coupled normal-and shear-stress flow problems were assessed,and their advantages and disadvantages were also analysed.Furthermore,different surface roughness descriptions and their impacts on mechanical and hydraulic behaviours were discussed,followed by the potential research directions for fracture flow problems.

Evaluation of Surface Roughness of Aluminum Alloy in Burnishing Process Based on Chaos Theory

Burnishing experiments with different burnishing parameters were performed on a computer numerical control milling machine to characterize the surface roughness of an aluminum alloy during burnishing.The chaos theory was employed to investigate the nonlinear features of the burnishing system.The experimental results show that the power spectrum is broadband and continuous,and the Lyapunov exponentλis positive,proving that burnishing has chaotic characteristics.The chaotic characteristic parameter,the correlation dimension D,is sensitive to the time behavior of the system and is used to establish the corresponding relationship with the surface roughness.The correlation dimension was the largest,when the surface roughness was the smallest.Furthermore,when the correlation dimension curve decreases,the roughness curve increases.The correlation dimension and surface roughness exhibit opposite variation trends.The higher the correlation dimension,the lower the surface roughness.The surface roughness of the aluminum alloy can be characterized online by calculating the correlation dimension during burnishing.

Experimental Research on the Surface Quality of Milling Contour Bevel Gears

Contour bevel gears have the advantages of high coincidence,low noise and large bearing capacity,which are widely used in automobile manufacturing,shipbuilding and construction machinery.However,when the surface quality is poor,the effective contact area between the gear mating surfaces decreases,affecting the stability of the fit and thus the transmission accuracy,so it is of great significance to optimize the surface quality of the contour bevel gear.This paper firstly analyzes the formation process of machined surface roughness of contour bevel gears on the basis of generating machining method,and dry milling experiments of contour bevel gears are conducted to analyze the effects of cutting speed and feed rate on the machined surface roughness and surface topography of the workpiece.Then,the surface defects on the machined surface of the workpiece are studied by SEM,and the causes of the surface defects are analyzed by EDS.After that,XRD is used to compare the microscopic grains of the machined surface and the substrate material for diffraction peak analysis,and the effect of cutting parameters on the microhardness of the workpiece machined surface is investigated by work hardening experiment.The research results are of great significance for improving the machining accuracy of contour bevel gears,reducing friction losses and improving transmission efficiency.

Interpolation Technique for the Underwater DEM Generated by an Unmanned Surface Vessel

High-resolution underwater digital elevation models(DEMs)are important for water and soil conservation,hydrological analysis,and river channel dredging.In this work,the underwater topography of the Panjing River in Shanghai,China,was measured by an unmanned surface vessel.Five different interpolation methods were used to generate the underwater DEM and their precision and applicability for different underwater landforms were analyzed through cross-validation.The results showed that there was a positive correlation between the interpolation error and the terrain surface roughness.The five interpolation methods were all appropriate for the survey area,but their accuracy varied with different surface roughness.Based on the analysis results,an integrated approach was proposed to automatically select the appropriate interpolation method according to the different surface roughness in the surveying area.This approach improved the overall interpolation precision.The suggested technique provides a reference for the selection of interpolationmethods for underwater DEMdata.

Effects of surface roughness on bending properties of rolled AZ31 alloy

This study investigated the effects of mechanical-polishing-induced surface roughness and the direction of polishing lines on the bending properties of a rolled AZ31 alloy.To this end,three-point bending tests were performed on one sample without polishing lines(SS sample)and two samples with polishing lines—one in which the polishing lines were parallel to the rolling direction(RS-RD sample)and the other in which they were parallel to the transverse direction(RS-TD sample).In all three samples,macrocracks were formed in the width direction on the outer surface,where tensile stress was predominantly generated in the longitudinal direction.However,the macrocracks formed in the SS sample were curved because of the merging of uniformly formed fine microcracks,whereas those formed in the RS-TD sample were linear owing to the formation of relatively coarse microcracks along the polishing lines.The bendability of the samples was in the order of SS>RS-RD>RS-TD,and their limiting bending depths were 4.8,4.6,and 4.4 mm,respectively.In the presence of mechanical-polishing-induced surface roughness,polishing lines perpendicular to the direction of the major stress(i.e.,tensile stress along the longitudinal direction)resulted in a greater degree of stress concentration on the outer surface of the bending specimen.This higher stress concentration promoted the formation of undesirable{10–11}contraction and{10–11}–{10–12}double twins—which typically act as crack initiation sites—and thereby facilitated crack generation and propagation.Consequently,the surface roughness caused premature fracture during bending deformation,which,in turn,caused deterioration of the bendability of the rolled Mg alloy.

Surface Characteristics Measurement Using Computer Vision:A Review

Computer vision provides image-based solutions to inspect and investigate the quality of the surface to be measured.For any components to execute their intended functions and operations,surface quality is considered equally significant to dimensional quality.Surface Roughness(Ra)is a widely recognized measure to evaluate and investigate the surface quality of machined parts.Various conventional methods and approaches to measure the surface roughness are not feasible and appropriate in industries claiming 100%inspection and examination because of the time and efforts involved in performing the measurement.However,Machine vision has emerged as the innovative approach to executing the surface roughness measurement.It can provide economic,automated,quick,and reliable solutions.This paper discusses the characterization of the surface texture of surfaces of traditional or non-traditional manufactured parts through a computer/machine vision approach and assessment of the surface characteristics,i.e.,surface roughness,waviness,flatness,surface texture,etc.,machine vision parameters.This paper will also discuss multiple machine vision techniques for different manufacturing processes to perform the surface characterization measurement.

Optimization of Rolling Parameters for Enhancing Surface Integrity of Aluminum Alloy

In this current work,aluminum alloy grade 2024 is adopted as a plate material that is used in the rolling process with three different parameters including thickness reduction,forming temperature,and density of lubrication type.The experimental procedure of the rolling process is performed using the design of the experiment based on the Taguchi technique(L27),then surface roughness,surface hardness,and surface residual stresses are measured.The results showed that the lubrication density has a significant impact on the surface roughness which depends on the lubrication properties(mineral oil type,natural fat,and kinematic viscosity)while surface hardness and surface residual stresses were strongly affected by thickness reduction.On the other side,the augment in forming temperature can decrease the quality of the final surface finish and the surface hardness but reduce the induced residual stresses.The best surface finish is obtained based on the optimum condition of the rolling factors are(R%_(3),T_(1),andρ_(3))while the optimum condition of rolling parameters that generate higher hardness and compressive residual stresses are(R%_(3)T_(1)ρ_(1)).

Unraveling the influence of surface roughness on oil displacement by Janus nanoparticles

Janus nanoparticles(JNPs)possess great potential in recovering the residual oil from reservoirs,however,the fundamental interaction mechanisms among nanoparticles,the oil,and reservoir wall characteristics remain to be elucidated.In this work,models of oil trapping grooves with different geometric features are subjected to molecular dynamics simulations for investigating the influences of roughness parameters on oil displacement dynamics by JNPs.Four key surface geometry parameters and different degrees of surface hydrophobicity are considered.Our results indicate that JNPs hold an outstanding performance in displacing residual oil on weakly to moderately hydrophobic surfaces.Overall,smaller entry and exit angles,the larger aspect ratio of the oil trapping grooves,and a bigger tip length of the rough ridges lead to superior oil recovery.Among the key geometric parameters,the aspect ratio of the oil trapping grooves plays the dominant role.These insights about the interaction of surface properties and JNPs and the resulting trapped oil displacement could serve as a theoretical reference for the application of JNPs for targeted reservoir conditions.

Shear sliding of rough-walled fracture surfaces under unloading normal stress

Through high-precision engraving,self-affine sandstone joint surfaces with various joint roughness coefficients(JRC=3.21e12.16)were replicated and the shear sliding tests under unloading normal stress were conducted regarding various initial normal stresses(1e7 MPa)and numbers of shearing cycles(1 e5).The peak shear stress of fractures decreased with shear cycles due to progressively smooth surface morphologies,while increased with both JRC and initial normal stress and could be verified using the nonlinear Barton-Bandis failure criterion.The joint friction angle of fractures exponentially increased by 62.22%e64.87%with JRC while decreased by 22.1%e24.85%with shearing cycles.After unloading normal stress,the sliding initiation time of fractures increased with both JRC and initial normal stress due to more tortuous fracture morphologies and enhanced shearing resistance capacity.The surface resistance index(SRI)of fractures decreased by 4.35%e32.02%with increasing shearing cycles due to a more significant reduction of sliding initiation shear stress than that for sliding initiation normal stress,but increased by a factor of 0.41e1.64 with JRC.After sliding initiation,the shear displacement of fractures showed an increase in power function.By defining a sliding rate threshold of 5105 m/s,transition from“quasi-static”to“dynamic”sliding of fractures was identified,and the increase of sliding acceleration steepened with JRC while slowed down with shearing cycles.The normal displacement experienced a slight increase before shear sliding due to deformation recovery as the unloading stress was unloaded,and then enhanced shear dilation after sliding initiation due to climbing effects of surface asperities.Dilation was positively related to the shear sliding velocity of fractures.Wear characteristics of the fracture surfaces after shearing failure were evaluated using binary calculation,indicating an increasing shear area ratio by 45.24%e91.02%with normal stress.

Influence of Input Factors on Surface Roughness and Material Removal Speed when Wire-EDM a Hardened SKD11 Steel Curve Profile

The goal of this research is to identify the best set of process machining parameters for wire-EDM(Electrical Discharge Machining)cutting of hardened SKD11 steel when machining a curve profile.The multi-objective function includes reducing surface roughness and increasing MRR(Material Removal Rate).The optimization process is prepared by using Taguchi method coupled Grey Relational Analysis.The obtained results revealed that Toff has the greatest influence on the average grey value(48.30%),followed by the influence of WF(Wire Feed,15.99%),VM(Cutting Voltage,9.33%),SV(Server Voltage,5.05%),Ton(Pulse on Time,1.81%),while SPD(Cutting Speed)has a negligible effect(0.89%).Moreover,using the optimal set of machining parameters generates in surface roughness of 1.25399mm and MRR of 26.5562 mm^(2)/min.The verification experiment and Anderson-Darling method demonstrate the validity of the proposed model,which can be utilized for estimating surface roughness and MRR.

Friction Characteristics Between Marine Clay and Construction Materials

Structure-soil interface friction characteristics is of importance to investigate the interaction between engineering structures and soils,especially for offshore structures.The interface friction behavior between marine clay and structural materials with different roughness was studied in this paper by using 3D optical scanning tests,a modified direct shear device and numerical simulation.Relationships between the surface roughness of structures,water content and interface friction angle were presented by model tests.The increase of water contents decreased the interface friction angles.For interfaces with different roughness,the interface friction angles will be smaller than that of the soil when the water content exceeds a certain value.The roughness of the interface and the water content of the soil are mutually coupled to influence the coefficient of friction(COF).This paper proposed a Finite Element Method(FEM)to simulate the interface direct shear tests of structures with different roughness.The surface models with different roughness are established based on the structure data obtained by 3D scanning.The Coupled Eulerian-Lagrangian(CEL)approach was employed to analyse soils sheared by irregular surfaces.The interface behavior for interfaces with different roughness under cyclic shear stresses was analyzed by FEM.

A Hybrid Optimization Approach of Single Point Incremental Sheet Forming of AISI 316L Stainless Steel Using Grey Relation Analysis Coupled with Principal Component Analysiss

We investigated the parametric optimization on incremental sheet forming of stainless steel using Grey Relational Analysis(GRA) coupled with Principal Component Analysis(PCA). AISI 316L stainless steel sheets were used to develop double wall angle pyramid with aid of tungsten carbide tool. GRA coupled with PCA was used to plan the experiment conditions. Control factors such as Tool Diameter(TD), Step Depth(SD), Bottom Wall Angle(BWA), Feed Rate(FR) and Spindle Speed(SS) on Top Wall Angle(TWA) and Top Wall Angle Surface Roughness(TWASR) have been studied. Wall angle increases with increasing tool diameter due to large contact area between tool and workpiece. As the step depth, feed rate and spindle speed increase,TWASR decreases with increasing tool diameter. As the step depth increasing, the hydrostatic stress is raised causing severe cracks in the deformed surface. Hence it was concluded that the proposed hybrid method was suitable for optimizing the factors and response.

Soil surface roughness change and its effect on runoff and erosion on the Loess Plateau of China

As an important parameter in the soil erosion model, soil surface roughness（SSR） is used to quantitatively describe the micro-relief on agricultural land. SSR has been extensively studied both experimentally and theoretically; however, no studies have focused on understanding SSR on the Loess Plateau of China. This study investigated changes in SSR for three different tillage practices on the Loess Plateau of China and the effects of SSR on runoff and erosion yield during simulated rainfall. The tillage practices used were zero tillage（ZT）, shallow hoeing（SH） and contour ploughing（CP）. Two rainfall intensities were applied, and three stages of water erosion processes（splash erosion（I）, sheet erosion（II） and rill erosion（III）） were analyzed for each rainfall intensity. The chain method was used to measure changes in SSR both initially and after each stage of rainfall. A splash board was used to measure the splash erosion at stage I. Runoff and sediment data were collected continuously at 2-min intervals during rainfall erosion stages II and III. We found that SSR of the tilled surfaces ranged from 1.0% to 21.9% under the three tillage practices, and the order of the initial SSR for the three treatments was ZT〈SH〈CP. For the ZT treatment, SSR increased slightly from stage I to III, whereas for the SH and CP treatments, SSR decreased by 44.5% and 61.5% after the three water erosion stages, respectively, and the greatest reduction in SSR occurred in stage I. Regression analysis showed that the changes in SSR with increasing cumulative rainfall could be described by a power function（R2〉0.49） for the ZT, SH and CP treatments. The runoff initiation time was longer in the SH and CP treatments than in the ZT treatment. There were no significant differences in the total runoff yields among the ZT, SH and CP treatments. Sediment loss was significantly smaller（P〈0.05） in the SH and CP treatments than in the ZT treatment.

The Simulation of Grinding Wheels and Ground Surface Roughness Based on Virtual Reality Technology

The paper describes the feasibility and method of the application of virtual reality technology to grinding process, and introduces the modeling method of object entity in the environment of virtual reality. The simulation process of grinding wheels and ground surface roughness is discussed, and the computation program system of numerical simulation is compiled with Visual C++ programming language. At the same time, the three-dimensional simulation models of grinding wheels and ground surface roughness are made with OpenGL tool. The choice of grinding wheels, the forecast of ground surface quality and some simulation results can be realized by interactively inputting grinding parameters. The paper applies virtual reality technology to grinding process,makes the model of virtual grinding wheel and simulates the grinding process. The roughness of ground surface is showed in three-dimensional images, and therefore the grinding technology is studied. Computer simulation can not only be used as a shortcut to analyze and research the grinding process, but also increase the research scope and content. The virtual reality technology used in the paper is an advanced visualized simulation with interaction. The surface roughness Ra on simulated ground workpiece can be calculated by the arithmetic average of contour warp absolute value in sampling length of simulated ground workpiece. The parameters of virtual wheel and simulated grinding process can be changed by interaction input, so the simulated results in the desired grinding condition are gained. The effect of each parameter to ground surface can be analyzed by comparing the grinding results in different condition.