1.3μm broadband swept sources with enhanced nonlinear effects

In this work,a new structure is used to enhance the nonlinear effect in the cavity,which improvesthe performance of the 1.3μm broadband swept source.The swept source adopts a semiconductoroptical amplifier(SOA),a circulator,a coupler,and a tunable filter.In the structure,the lightpasses through the nonlinear medium(SOA)twice in two opposite directions,which excites thenonlinear ffect and increases the performance of the swept source.The tunable filter is based on apolygon rotating mirror and gratings.Traditionally,multiple SOAs are adopted to improve thesweep range and the optical power,which increases the cost and complexity of the swept source.The method proposed in this paper can improve the spectral range and optical power of the sweptsources without additional accessories.For the short-cavity swept source,the power increasesfrom 6 mW to 7.7 mW,and the sweep range increases from 98 nm to 120 nm.The broadband swept sources could have wide applications in biomedical imaging,sensor system,measurementand so on.

Bimodal imaging of proliferative diabetic retinopathy vascular features using swept source optical coherence tomography angiography

AIM： To categorize neovessels morphology and to detect response to anti-angiogenic therapy by using structural and angiographic modes of swept source optical coherence tomography（SS-OCT）.METHODS： Thirty-two eyes with neovessels at disc（NVD） and neovessels elsewhere（NVE）-as diagnosed by fluorescein angiography-were included. Cross sectional OCT images of disc and macular regions were registered to enface OCT angiography（OCTA）, B-scan blood flow over lay and density maps. Three eyes received antiangiogenic treatment.RESULTS： Pin point registration of cross-sectional OCT and OCTA images differentiated active NVD with vascular elements from fibrous or equivalent fibrovascular elements. En face images delineated NVE as vascular tufts or area of filling while cross-sectional images differentiated NVE from microvascular intraretinal abnormality（IRMA）. All cases were associated with enlargement of foveal avascular zone and or areas of capillary non perfusion. Regressed NVD appeared as ghost vessel or pruned vascular loops after injection.CONCLUSION： Structural and angiographic modes of SS-OCT can detect, characterize and categorize the pattern of wide spectrum of neovessels based on blood flow data and density maps. It is potentially useful to detect ischemic changes in the vascular bed and regression of NVD after therapeutic regimens providing substitute for invasive techniques.

PDGI-BASED REGULAR SWEPT SURFACE EXTRACTION FROM POINT CLOUD

A principal direction Gaussian image （PDGI）-based algorithm is proposed to extract the regular swept surface from point cloud. Firstly, the PDGI of the regular swept surface is constructed from point cloud, then the bounding box of the Gaussian sphere is uniformly partitioned into a number of small cubes （3D grids） and the PDGI points on the Gaussian sphere are associated with the corresponding 3D grids. Secondly, cluster analysis technique is used to sort out a group of 3D grids containing more PDGI points among the 3D grids. By the connected-region growing algorithm, the congregation point or the great circle is detected from the 3D grids. Thus the translational direction is determined by the congregation point and the direction of the rotational axis is determined by the great circle. In addition, the positional point of the rotational axis is obtained by the intersection of all the projected normal lines of the rotational surface on the plane being perpendicular to the estimated direction of the rotational axis. Finally, a pattem search method is applied to optimize the translational direction and the rotational axis. Some experiments are used to illustrate the feasibility of the above algorithm.

Observation of the early blood vessels of cutaneous malignant melanoma using Swept Source Optical Coherence Tomography A ngiography(SS-OCTA)

Melanoma,characterized by high mortality,rapid development and accompanied with angio-genesis is the most typical malignant tumor in skin cancer.Hence,the detection of blood vessels is of much significanoe.The early vascular network has small scale.If we remove the tumor early and biopsy it,it will increase the spread of the cancer cells and infection and bleeding.In this case,we presented a new angiography method.A high-resolution OCT system for noninvasive an-giographic imaging of early skin melanoma-Swept Source Optical Coberence Tomography Angiography(SS-OCTA)is proposed.With a high lateral resolution of 10pm in vrivo tomographic angiography,SS-OCTA is used to image and identify the morphology of the early tumor blood vessels.In addition,a control group experiment is conducted to observe the growth of melanoma in the process of rupture,malormation of micro-vessels.The results of the analysis and statistical test(P<0.05)are statistically signifcant.

Applications of EPSE method for predicting crossflow instability in swept-wing boundary layers

The nth-order expansion of the parabolized stability equation （EPSEn） is obtained from the Taylor expansion of the linear parabolized stability equation （LPSE） in the streamwise direction. The EPSE together with the homogeneous boundary conditions forms a local eigenvalue problem, in which the streamwise variations of the mean flow and the disturbance shape function are considered. The first-order EPSE （EPSE1） and the second-order EPSE （EPSE2） are used to study the crossflow instability in the swept NLF（2）-0415 wing boundary layer. The non-parallelism degree of the boundary layer is strong. Compared with the growth rates predicted by the linear stability theory （LST）, the results given by the EPSE1 and EPSE2 agree well with those given by the LPSE. In particular, the results given by the EPSE2 are almost the same as those given by the LPSE. The prediction of the EPSE1 is more accurate than the prediction of the LST, and is more efficient than the predictions of the EPSE2 and LPSE. Therefore, the EPSE1 is an efficient ey prediction tool for the crossflow instability in swept-wing boundary-layer flows.

Broadband and high-speed swept external-cavity laser using a quantum-dot superluminescent diode as gain device

A wide wavelength tuning range swept external-cavity laser using an In As/Ga As quantum-dot superluminescent diode as a gain device is demonstrated. The tunable filter consists of a polygon scanner and a grating in Littrow telescope-less configuration. The swept laser generates greater than 54-m W peak output power and up to 33-k Hz sweep rate with a sweep range of 150 nm centered at 1155 nm. The effects of injection current and sweep rate on the sweep performance of the swept laser are studied.

STUDY OF SWEPT SHOCK WAVE AND BOUNDARY LAYER INTERACTIONS

This paper presents briefly the recent progress on study of swept shock wave/boundary layer interactions with emphasis on application of zonal analysis and correlation analysis to them. Based on the zonal analysis an overall framework of complicated interaction flow structure including both surface flowfield and space flowfield is discussed. Based on correlation analysis the conical interactions induced by four families of shock wave generators have been discussed in detail. Some control parameter and physical mechanism of conical interaction have been revealed. Finally some aspects of the problem and the prospects for future work are suggested.

Theoretical Study of Wind Turbine Model with a New Concept on Swept Area

Commercially available wind-turbines are optimized to operate at certain wind velocity, known as rated wind velocity. For other values of wind velocity, it has different output which is lower than the rated output of the wind plant. Wind mill can be designed to provide maximum power output at different wind velocities through modification of swept area to match with the wind speed available at the moment. This can result in higher power output at all the velocities except that at rated wind speed because of limitation of generator. This results in increased utilization of generation capacity of wind mill compared to its commercially designed counterpart. A theoretical simulation has been done to prove a new concept about swept area of wind turbine blade which results in a significant increase in the power output through the year. Simulation results of power extracted through normal wind blade design and new concept are studied and compared. The findings of the study are presented in graphical and tabular form. Study establishes that there can be a significant gain in the power output with the new concept.

A NOVEL SWEPT LASER SOURCE BASED ON COMBINED TUNABLE FILTERS FOR OCT

A novel broad tunable bandwidth and narrow instantaneous line-width linear swept laser source using combined tunable filters working at 1,300 nm center wavelength is proposed.The combined filters consist of a fiber Fabry
Perot tunable filter and a tunable filter based on diffractive grating with scanning polygon mirror.In contrast to traditional method using single tunable filter,the trade-off between bandwidth and instantaneous line-width is alleviated.Parallel implementation of two semiconductor optical amplifiers with different wavelength range is adopted in the laser resonator for broadband light amplification.The Fourier domain mode locking swept laser source with combined tunable filters offers broadband tunable range with narrow instantaneous line-width,which is especially benefiting for high-quality optical frequency domain imaging.The proposed Fourier domain mode locking swept laser source provides a tuning range of 160 nm with instantaneous line-width of about 0.01nm at sweeping rate of 15 kHz,a finesse of 16,000 is thus achieved.

Mechanism of expanding swept volume by nano-sized oil-displacement agent

The effect of expanding swept volume by iNanoW1.0 nanoparticles in ultra-low permeability core was studied by low-field nuclear magnetic resonance(LF-NMR)technology,and the mechanism of expanding swept volume was explained by oxygen spectrum nuclear magnetic resonance(17O-NMR)experiments and capillarity analysis.The results of the LF-NMR experiment show that the nano-sized oil-displacement agent iNanoW1.0 could increase the swept volume by 10%-20%on the basis of conventional water flooding,making water molecules get into the low permeable region with small pores that conventional water flooding could not reach.17O-NMR technique and capillary analysis proved that iNanoW1.0 nanoparticles could weaken the association of hydrogen bonds between water molecules,effectively change the structure of water molecular clusters,and thus increasing the swept volume in the low permeable region.The ability of weakening association of hydrogen bonds between water molecules of iNanoW1.0 nanoparticles increases with its mass fraction and tends to be stable after the mass fraction of 0.1%.

Gain-Scheduling H_∞ Autopilot Design for Tactical Missiles with Variable-Swept Wings

A new approach to gain-scheduling of H∞controllers is proposed for a cruise missile with variableswept wings( VSW) in bank-to-turn( BTT) mode. A nonlinear dynamic model is established and anticipant performance criterions are given at first. For the selected operating points,feedback robust controllers of threechannels are designed independently to restrain cross-channel couple disturbances and aerodynamic perturbations. Then,the sweepback and Ma number are selected to schedule controller gains iteratively to ensure all closed-loop poles locating inside the desired region. The proposed method here attempts to extend the performance of initial design obtained for a single arbitrary point to the whole linearized domain while maintaining the expected stability over the entire range of sweepback and full flight envelope. Some time-domain analysis procedures based on the proposed method are carried out and assessed,while the performance of tracking and robustness to aerodynamic perturbations in different situations are contrasted by some nonlinear simulations. Finally,the numerical simulations demonstrate that the proposed autopilot design method has better tracking performance and is robust,effective and feasible.

Renal function and choroidal thickness using swept-source optical coherence tomography in diabetic patients

AIM: To assess the relationship between choroidal thickness and renal function in diabetic patients. METHODS: Cross-sectional retrospective clinical study of 42 eyes of 21 ocular treatment-na?ve diabetic patients. Demographic data included: age, sex, type and course of diabetes. Ocular data included: severity of diabetic retinopathy;retinal thickness at the central macular region, as well as choroidal thickness at the central and paracentral quadrants, using automatically generated maps by swept-source optical coherence tomography;presence of cystic macular edema;and ocular axial length(AXL). Lab-test parameters included: glycated hemoglobin(HbA1c), albuminuria, albumin/creatinine ratio in urine, and glomerular filtration rate. RESULTS: A significant negative correlation was mainly observed between several choroidal thicknesses, age(P<0.020) and ocular AXL(P<0.030). On the contrary, a significant positive correlation was found between all choroidal thicknesses, HbA1 c(P<0.035) and albuminuria(P<0.040). CONCLUSION: Choroidal thickness can represent an additional tool to help clinicians predicting the renal status in ocular treatment-na?ve diabetic patients.

Swept-Volume Display System Based on Cylindrical Space Projection and Curved Reflectors

In order to achieve a clear and steady swept-volume display,the method of swept-volume display based on cylindrical space projection was presented. One projector generated the image volume in π× 70 mm × 70 mm × 150 mm space. Experimentally,the resolution of images was 800 pixel × 600 pixel × 360 pixel,which resulted in almost 345 million voxels. In order to achieve space voxels with uniform brightness, curved reflectors were also designed. In addition,the match conditions between triangles and the scanning planes in the volume space were classified and a sweptvolume graphics engine based on embedded platform was designed.The image rendering the hardware foundation for three-dimensional( 3D) dynamic images generation was achieved. Demonstrated in the experiments,light source utilization of the second-generation system based on curved mirror is about three times brighter than the firstgeneration 3D minitor based on flat mirror,and this system is able to display color,clear and well-proportioned 3D images in brighter room light.

A THEORETICAL INVESTIGATION OF THE DEVELOPMENT OF STATIONARY CROSSFLOW VORTICES IN THE BOUNDARY LAYER ON A SWEPT WING

Crossflow instability plays very important role in the transition of the boundary layer on a swept wing, typical in the engineering applications. Experiments revealed that the linear stability theory well predicted the form of the crossflow vortices, but usually much overpredicted their growth rate. Using nonlinear theory of hydrodynamic stability, combined with some other considerations, we were able to obtain the growth rate in good agreement with experimental observations.

High-Speed Optical Coherence Tomography System Using a 200-kHz Swept Light Source with a KTN Deflector

We demonstrate a high-speed swept-source optical coherence tomography (SS-OCT) system, which is based on a high-speed swept light source and a Mach-Zehnder interferometer with a high-speed photodetector. The light source is an external-cavity laser tuned by a KTN electro-optic deflector, which exhibits a very fast response and large deflection. The scanning wavelength range is almost 80 nm up to 200 kHz with a ±400-V deflector driving voltage. The system acquires 1 mm × 1 mm images consisting of 200 × 200 pixels within few milliseconds. We present preliminary SS-OCT images of an in-vitro human nail and an in-vivo finger pad.

A Windstorm Swept over Intellectual Capitalists

InSeptember1999.JiangQiping'snewbook,AWindstormSweptOverIntellectualCapitalists.,causedquiteastirwhenitfirstappearedinBeijing'sbookstores.Theideaofanintellectualcapitalist,althoughnotinventedbythisinstantbestselles,hasbecomeahottopicofdiscussionamong...

Trimming self-intersections in swept volume solid modeling

Swept volume solid modeling has been applied to many areas such as NC machining simulation and verification, robot workspace analysis, collision detection, and CAD. But self-intersections continue to be a challenging problem in the boundary representation of swept volume solids. A novel algorithm is presented in this paper to trim self-intersection regions in swept volume solids modeling. This trimming algorithm consists of two major steps: (1) roughly detecting self-intersection regions by checking intersections or overlapping of the envelop profiles; (2) splitting the whole envelop surfaces of the swept volume solid into separate non-self-intersecting patches to trim global self-intersections, and to trim local self-intersections, dividing local self-intersecting regions into patches and replacing self-intersecting patches with non-self-intersecting ones. Examples show that our algorithm is efficient and robust.

Transfer learning from two-dimensional supercritical airfoils to three-dimensional transonic swept wings

Machine learning has been widely utilized in flow field modeling and aerodynamic optimization.However,most applications are limited to two-dimensional problems.The dimensionality and the cost per simulation of three-dimensional problems are so high that it is often too expensive to prepare sufficient samples.Therefore,transfer learning has become a promising approach to reuse well-trained two-dimensional models and greatly reduce the need for samples for threedimensional problems.This paper proposes to reuse the baseline models trained on supercritical airfoils to predict finite-span swept supercritical wings,where the simple swept theory is embedded to improve the prediction accuracy.Two baseline models are investigated:one is commonly referred to as the forward problem of predicting the pressure coefficient distribution based on the geometry,and the other is the inverse problem that predicts the geometry based on the pressure coefficient distribution.Two transfer learning strategies are compared for both baseline models.The transferred models are then tested on complete wings.The results show that transfer learning requires only approximately 500 wing samples to achieve good prediction accuracy on different wing planforms and different free stream conditions.Compared to the two baseline models,the transferred models reduce the prediction error by 60%and 80%,respectively.

Improvement of bandwidth in a 100 kHz swept laser source with phase controllable signal driving

Swept source optical coherence tomography(SS-OCT)is a new noninvasive technique for assessing tissue.Although it hasadvantages,such as being label-free,noninvasive,and with high resolution,it also has drawbacks:there has been no indepth research into identifying the driving of swept source.Based on preliminary research,we demonstrate a novel drivingmodulation method of a fiber Fabry–Perot tunable filter ranging phase adjustable as a tool for making bandwidth compensation of a swept laser source.This novel method is analyzed in detail;a swept laser source with a sweep rate of100.5 kHz over a range of 152.25 nm and at a center wavelength of 1335.45 nm is demonstrated.

Scallop ice shape characteristics of swept wing based on large-scale icing wind tunnel experiment

Scallop ice is a special phenomenon that occurs during swept wing aircraft passing through icing clouds.It poses a great challenge for the icing safety assessment that the complex scallop ice shape feature and its mechanism are still unclear.In this work,a large-scale icing wind tunnel experiment of swept wing designed by NACA0012 airfoil is conducted in the Icing Wind Tunnel of China Aerodynamics Research and Development Center.The detailed three-dimensional ice shapes under 0°,15°,30°and 45°swept angles are obtained by laser scanning technology.The experimental results show that with the swept angle increasing from 0°to 45°,the 2D double ice horn structures show certain spanwise variation,and finally transform into complete scallop ice with ice thickness greatly enhanced in the stagnation line region.The empirical mode decomposition of the spanwise ice curve captures the high-frequency fluctuation on the scallop ice caused by the small-scale roughness element,while the trend with low frequency is not obvious.Based on the experimental data,a new complete scallop ice geometric model,named 5Points-5Lines-2Arcs(5P-5L-2A)model,is proposed,which can provide important basis for the quantitative description of complex scallop ice shape.