Radiant syngas cooler(RSC)is widely used as a waste heat recovery equipment in industrial gasification.In this work,an RSC with radiation screens is established and the impact of gaseous radiative property models,gas ...Radiant syngas cooler(RSC)is widely used as a waste heat recovery equipment in industrial gasification.In this work,an RSC with radiation screens is established and the impact of gaseous radiative property models,gas components,and ash particles on heat transfer is investigated by the numerical simulation method.Considering the syngas components and the pressure environment of the RSC,a modified weighted-sum-of-gray-gases model was developed.The modified model shows high accuracy in validation.In computational fluid dynamics simulation,the calculated steam production is only 0.63%in error with the industrial data.Compared with Smith's model,the temperature decay along the axial direction calculated by the modified model is faster.Syngas components are of great significance to heat recovery capacity,especially when the absorbing gas fraction is less than 10%.After considering the influence of particles,the outlet temperature and the proportion of radiative heat transfer are less affected,but the difference in steam output reaches 2.7 t·h^(-1).The particle deposition on the wall greatly reduces the heat recovery performance of an RSC.展开更多
Selective synthesis of ethanol from syngas under the Co-based catalysts is still challenging due to the hard of regulating the active site Co^(0) and Co^(2+)ratio.In this work,a series of CaTi_(0.9-x)Co_(x)Mo_(0.1)O_(...Selective synthesis of ethanol from syngas under the Co-based catalysts is still challenging due to the hard of regulating the active site Co^(0) and Co^(2+)ratio.In this work,a series of CaTi_(0.9-x)Co_(x)Mo_(0.1)O_(3)(x=0,0.1-0.4)and CaTi_(0.7)Co_(0.3)O_(3) catalysts were prepared by using citric acid complexation method to promote the synthesis of ethanol.It was found that Mo species in the perovskite lattice can regulate the Co^(0) and Co^(2+)ratio through the domain-limiting effect of perovskite and the degree of Co reduction could be adjusted by changing the Co/Mo molar ratio.Among these investigated catalysts,the total selectivity of alcohols over the catalyst with the optimal Co/Mo ratio CaTi_(0.6)Co_(0.3)Mo_(0.1)O_(3) reached 39.1%,with ethanol accounting for 74.7%,which was ascribed to the moderate and tightly bound ratio of dissociative to non-dissociative adsorption sites on the surface and the balance of CH_(x)-CH_(y) coupling and C^(O) insertion.展开更多
Direct conversion of syngas to aromatics has great potential to decrease fossil fuel dependence.Here,a unique structured hybrid catalyst composed of Fe_(3)O_(4) nanoparticles intimately dispersed inside an acidic zeol...Direct conversion of syngas to aromatics has great potential to decrease fossil fuel dependence.Here,a unique structured hybrid catalyst composed of Fe_(3)O_(4) nanoparticles intimately dispersed inside an acidic zeolite is developed.1 to 4 nm sized Fe_(3)O_(4) nanoparticles end up evenly dispersed in an acidic and slightly mesoporous Al-ZSM-5 based on Fe_(3)O_(4) restructuring during co-hydro thermal synthesis using organosilane modification.A very high aromatic productivity of 214 mmolaromatics h^(-1) gFe^(-1) can be obtained with a remarkable 62%aromatic selectivity in hydrocarbons.This catalyst has excellent sintering resistance ability and maintains stable aromatics production over 570 h.The synthetic insights that postulate a mechanism for the metastable oxide-zeolite reorganization during hydrothermal synthesis could serve as a generic route to sinter-resistant oxide-zeolite composite materials with uniform,well-dispersed oxide nanoparticles in close intimacy with-and partially confined in-a zeolite matrix.展开更多
In the conversion process of syngas-to-C_(2)species,the OH species are inevitably produced accompanying the production of key intermediates CH_(x)(x=1-3),traditionally,the function of surface OH species is generally a...In the conversion process of syngas-to-C_(2)species,the OH species are inevitably produced accompanying the production of key intermediates CH_(x)(x=1-3),traditionally,the function of surface OH species is generally accepted as the hydrogenating reactive species.This work for the first time proposed and confirmed the assisted catalytic mechanism of surface OH species that performed as the promoter for syngas-to-C_(2)species on Cu-based catalysts.DFT and microkinetic modeling results reveal that the produced OH species accompanying the intermediates CH_(x)production on the MCu(M=Co,Fe,Rh)catalysts can stably exist to form OH/MCu catalysts,on which the presence of surface OH species as the promoter not only presented better activity and selectivity toward CH_(x)(x=1-3)compared to MCu catalysts,but also significantly suppressed CH_(3)OH production,providing enough CH_(x)sources to favor the production of C_(2)hydrocarbons and oxygenates.Correspondingly,the electronic properties analysis revealed the essential relationship between the electronic feature of OH/MCu catalysts and catalytic performance,attributing to the unique electronic micro-environment of the catalysts under the interaction of surface OH species.This new mechanism is called as OH-assisted catalytic mechanism,which may be applied in the reaction systems related to the generation of OH species.展开更多
Direct conversion of syngas to aromatics(STA)over oxide-zeolite composite catalysts is promising as an alternative method for aromatics production.However,the structural effect of the oxide component in composite cata...Direct conversion of syngas to aromatics(STA)over oxide-zeolite composite catalysts is promising as an alternative method for aromatics production.However,the structural effect of the oxide component in composite catalysts is still ambiguous.Herein,we investigate the size effect by selecting ZnCr_(2)O_(4)spinel,as a probe oxide,mixing with H-ZSM-5 zeolite as a composite catalyst for STA reaction.The CO conversion,aromatics selectivity and space-time yield(STY)of aromatics are all significantly improved with the crystal size of ZnCr_(2)O_(4)oxide decreases,which can mainly attribute to the higher oxygen vacancy concentration and thus the rapid generation of more C1oxygenated intermediate species.Based on the understanding of the size-performance relationship,ZnCr_(2)O_(4)-400 with a smaller size mixing with H-ZSM-5 can achieve32.6%CO conversion with 76%aromatics selectivity.The STY of aromatics reaches as high as 4.79 mmol g_(cat)^(-1)h^(-1),which outperforms the previously reported some typical catalysts.This study elucidates the importance of regulating the size of oxide to design more efficient oxidezeolite composite catalysts for conversion of syngas to value-added chemicals.展开更多
Coral reef-like Ni/Al2O3 catalysts were prepared by co-precipitation of nickel acetate and aluminium nitrate with sodium carbonate aqueous solution in the medium of ethylene glycolye.Methanation of syngas was carried ...Coral reef-like Ni/Al2O3 catalysts were prepared by co-precipitation of nickel acetate and aluminium nitrate with sodium carbonate aqueous solution in the medium of ethylene glycolye.Methanation of syngas was carried out over coral reef-like Ni/Al2O3 catalysts in a continuous flow type fixed-bed reactor.The structure and properties of the fresh and used catalysts were studied by SEM,N2 adsorption-desorption,XRD,H2-TPR,O2-TPO,TG and ICP-AES techniques.The results showed that the coral reef-like Ni/Al2O3 catalysts exhibited better activity than the conventional Ni/Al2O3-H2O catalysts.The activities of coral reef-like catalysts were in the order of Ni/Al2O3-673Ni/Al2O3-573Ni/Al2O3- 473Ni/Al2O3-773.Ni/Al2O3-673-EG catalyst showed not only good activity and improved stability but also superior resistance to carbon deposition,sintering,and Ni loss.Under the reaction conditions of CO/H2(molar ratio)=1:3,593 K,atmospheric pressure and a GHSV of 2500 h-1,CH4 selectivity was 84.7%,and the CO conversion reached 98.2%.展开更多
A series of noble metal catalysts (Ru, Rh, Ir, Pt, and Pd) supported on alumina-stabilized magnesia (Spinel) were used to produce syngas by methane reforming with carbon dioxide. The synthesized catalysts were cha...A series of noble metal catalysts (Ru, Rh, Ir, Pt, and Pd) supported on alumina-stabilized magnesia (Spinel) were used to produce syngas by methane reforming with carbon dioxide. The synthesized catalysts were characterized using BET, TPR, TPO, TPH, and H2S chemisorption techniques. The activity results showed high activity and stability for the Ru and Rh catalysts. The TPO and TPH analyses indicated that the main reason for lower activity and stability of the Pd catalyst was the formation of the less reactive deposited carbon and sintering of the catalyst.展开更多
Oxide-Zeolite(OX-ZEO) bifunctional catalyst design concept has been exemplified in several processes to direct conversion syngas to value-added chemicals and fuels such as mixed light olefins, ethylene, aromatics and ...Oxide-Zeolite(OX-ZEO) bifunctional catalyst design concept has been exemplified in several processes to direct conversion syngas to value-added chemicals and fuels such as mixed light olefins, ethylene, aromatics and gasoline.Herein we demonstrate that the product can be steered toward liquefied petroleum gas(LPG) with a selectivity up to 89% in hydrocarbons especially propane selectivity reaching 80% at CO conversion of 63% using ZnCrOx-H-SSZ-39 catalyst.Interestingly, the quantity of the acid sites of SSZ-39 does not influence obviously the hydrocarbon distribution but the strength is crucial for selective formation of propane.This finding provides an alternative route of LPG synthesis from a variety of carbon resources via syngas.展开更多
This research focused on the feasibility of applying the forward and reverse combustion approach to the in situ gasification of lignite with the production of hydrogen-rich syngas(H_(2)and CO).The so-called forward co...This research focused on the feasibility of applying the forward and reverse combustion approach to the in situ gasification of lignite with the production of hydrogen-rich syngas(H_(2)and CO).The so-called forward combustion gasification(FCG)and reverse combustion gasification(RCG)approach in which oxygen and steam are simultaneously fed to the simulated system of underground coal gasification(UCG)was studied.A simulated system of UCG was designed and established.The underground conditions of the coal seam and strata were simulated in the system.The combustion gasification of lignite has been carried out experimentally for almost 6.5 days.The average effective content(H_(2)+CO)of syngas during the FCG phase was 62.31%and the maximum content was 70.92%.For the RCG phase the corresponding figures are 61.33%and 67.91%.Thus,the feasibility of using RCG way for UCG has been demonstrated.The temperature profiles have been provided by using of 85 thermocouples during the model experiment,which portrayed the several nephograms of thermal data in the gasifier were of significance for the prospective gasification processes.展开更多
Ni/Al2O3 catalysts with different amounts of manganese ranging from 1 to 3 wt% as promoter were prepared by co-impregnation method. The catalysts were characterized by N2 physisorption, XRD, TPR, SEM and TEM. Their ca...Ni/Al2O3 catalysts with different amounts of manganese ranging from 1 to 3 wt% as promoter were prepared by co-impregnation method. The catalysts were characterized by N2 physisorption, XRD, TPR, SEM and TEM. Their catalytic activity towards syngas methanation reaction was also investigated using a fixed-bed integral reactor. It was demonstrated that the addition of manganese to Ni/Al2O3 catalysts can increase the catalyst surface area and average pore volume, but decrease NiO crystallite size, leading to higher activity and stability. The effects of reaction temperature, pressure and weight hourly space velocity (WHSV) on carbon oxides conversion and CH4 formation rate were also studied. High carbon oxides conversion, CH4 selectivity and formation rate were achieved at the reaction temperature range of 280 300℃.展开更多
A series of Cu-based catalysts were developed for alkylation of benzene with syngas. The catalyst samples were prepared by the impregnation method, and were characterized by XRD, XRF, NH3-TPD, and TEM and evaluated in...A series of Cu-based catalysts were developed for alkylation of benzene with syngas. The catalyst samples were prepared by the impregnation method, and were characterized by XRD, XRF, NH3-TPD, and TEM and evaluated in a fixed bed reactor. The optimized reaction temperature of Cu/Al2O3/ZSM-5 catalyst was 350 ℃, while higher contents of copper were conducive to alkylation of benzene with syngas. The new medium strength acid centers in the catalyst created by Cu were beneficial to alkylation. Hydrogenation reaction of CO was executed on the metal centers without dissociation, Dimethyl ether(DME) was the major intermediate over Cu-based catalysts. Higher selectivity of methylation and lower selectivity of heavy aromatics were confirmed after the second metal(Zn, Mn, or V) was added to the copper catalyst. Cu was partly covered by Zn in the Cu-Zn/Al2O3/ZSM-5 catalyst leading to low dispersion and low activity of copper. Cu-Mn/Al2O3/ZSM-5 catalyst possessed the best yield of methylation product. Cu-Mn composite oxides were probably formed in fresh catalyst, which blocked the sintering of Cu in the reaction process. The loading of Cu decreased dramatically after the introduction of V, while causing an increase of the amount of medium strength acid centers at the same time. V prevented the sintering of copper particles during the reducing process and had a promoting effect on the activity of Cu.展开更多
Cu-Co bi-metal catalysts derived from CuO/LaCoO3 perovskite structure were prepared by one-step citrate complexing method, and the structure evolution reaction from CuO/LaCoO3 to Cu-Co2C/La202CO3 under 1-12 pretreatme...Cu-Co bi-metal catalysts derived from CuO/LaCoO3 perovskite structure were prepared by one-step citrate complexing method, and the structure evolution reaction from CuO/LaCoO3 to Cu-Co2C/La202CO3 under 1-12 pretreatment was investigated by techniques of XRD, TPR and TEM. The results suggest that a much higher dispersion of copper significantly enhanced the reduction of cobalt, and a stronger interaction between copper and cobalt ions in LaCoO3 particles led to the formation of bi-metallic Cu-Co particles in the reduced catalysts and the enrichment of Co on the surface of bimetallic particles. The prepared catalysts were highly active and selective for the alcohol synthesis from syngas due to the presence of copper-modified C02C species.展开更多
In this work,syngas methanation over Ni-W/TiO2-SiO2catalyst was studied in a fluidized-bed reactor(FBR)and its performance was compared with a fixed-bed reactor(FIXBR).The effects of main operating variables including...In this work,syngas methanation over Ni-W/TiO2-SiO2catalyst was studied in a fluidized-bed reactor(FBR)and its performance was compared with a fixed-bed reactor(FIXBR).The effects of main operating variables including feedstock gases space velocity,coke content,bed temperature and sulfur-tolerant stability of 100 h life were investigated.The structure of the catalysts was characterized by XRD,N2adsorptiondesorption and TEM.It is found that under same space velocity from 5000 h 1to 25000 h 1FBR gave a higher CH4yield,lower coke content,and lower bed temperature than those obtained in FIXBR.Ni-W/TiO2-SiO2catalyst possessed excellent sulfur-tolerant stability on the feedstock gases less than 500 ppm H2S in FBR.The carbon deposits formed on the spent catalyst were in the form of carbon fibers in FBR,while in the form of dense accumulation distribution appearance in FIXBR.展开更多
The nanosheets structured K–Co–MoS_2 catalyst was prepared through a one-step hydrothermal synthesis combined with the wetness impregnation. The fresh catalyst has a high dispersion of Co–Mo–S active phase and no ...The nanosheets structured K–Co–MoS_2 catalyst was prepared through a one-step hydrothermal synthesis combined with the wetness impregnation. The fresh catalyst has a high dispersion of Co–Mo–S active phase and no Co_9S_8 is found. The pure H_2 activated catalyst shows a higher intrinsic activity, especially the C_(2+) OH selectivity for the higher alcohol synthesis compared to the one activated by 5% H_2/N_2 atmosphere. The reason is attributed to that the pure H_2 activation more effectively suppresses the formation of Co_9S_8 and stabilizes the Co–Mo–S active phase during the reaction due to the formation of SH species.展开更多
Visible-light-driven CO2 photoreduction to achieve renewable materials,such as syngas,hydrocarbons,and alcohols,is a key process that could relieve environmental problems and the energy crisis simultaneously.Reduction...Visible-light-driven CO2 photoreduction to achieve renewable materials,such as syngas,hydrocarbons,and alcohols,is a key process that could relieve environmental problems and the energy crisis simultaneously.Reduction of syngas products with diff erent H2:CO proportions is highly expected to produce high value-added chemicals in the industry.However,the development of technologies employing long-wavelength irradiation to achieve CO2 photoreduction and simultaneous tuning of the resultant H2:CO proportion remains a challenging endeavor.In this work,we carried out interfacial engineering by designing a series of heterostructured layered double-hydroxide/MoS2 nanocomposites via electrostatic self-assembly.The syngas proportion(H 2:CO)obtained from CO2 photoreduction could be modulated from 1:1 to 9:1 by visible-light irradiation(λ>400 nm)under the control of the interface-rich heterostructures.This work provides a cost-eff ective strategy for solar-tofuel conversion in an artificial photosynthetic system and describes a novel route to produce syngas with targeted proportions.展开更多
Photocatalytic reduction of CO2 with H2 O to syngas is an effective way for producing high value-added chemical feedstocks such as methanol and light olefins in industry.Nevertheless,the precise control of CO/H2 ratio...Photocatalytic reduction of CO2 with H2 O to syngas is an effective way for producing high value-added chemical feedstocks such as methanol and light olefins in industry.Nevertheless,the precise control of CO/H2 ratio from photocatalytic CO2 reduction reaction still poses a great challenge for the further application.Herein,we prepared a series of highly efficient heterostructure based on highly dispersed palladium supported on ultrathin Co Al-layered double hydroxide(LDH).In conjunction with a Ru-complex sensitizer,the molar ratios of CO/H2 can be tuned from 1:0.74 to 1:3 under visible-light irradiation(λ>400 nm).More interestingly,the syngas can be obtained under light irradiation atλ>600 nm.Structure characterization and density functional theory calculations revealed that the remarkable catalytic activity can be due to the supported palladium,which improved the charge transfer efficiency.Meanwhile,more H atoms were used to generate H2 on the supported palladium for further tunable CO/H2 ratio.This work demonstrates a new strategy for harnessing abundant solar-energy to produce syngas from a CO2 feedstock.展开更多
CeO2 oxygen carrier was prepared by precipitation method and tested by two-step steam reforming of methane (SRM). Two-step SRM for hydrogen and syngas generation is investigated in a fixed-bed reactor. Methane is di...CeO2 oxygen carrier was prepared by precipitation method and tested by two-step steam reforming of methane (SRM). Two-step SRM for hydrogen and syngas generation is investigated in a fixed-bed reactor. Methane is directly converted to syngas at a H2/CO ratio close to 2 : 1 at a high temperature (above 750 °C) by the lattice oxygen of CeO2; methane cracking is found when the reduction degree of CeO2 was above 5.0% at 850 °C in methane isothermal reaction. CeO2?δ obtained from methane isothermal reaction can split water to generate CO-free hydrogen and renew its lattice oxygen at 700 °C; simultaneously, deposited carbon is selectively oxidized to CO2 by steam following the reaction (C+2H2O→CO2+2H2). Slight deactivation in terms of amounts of desired products (syngas and hydrogen) is observed in ten repetitive two-step SRM process due to the carbon deposition on CeO2 surface as well as sintering of CeO2.展开更多
CexZr1-xO2 mixed oxides with different Ce/Zr ratios were prepared by coprecipitation. The characterizations of mixed oxides were studied by X-ray diffraction (XRD) and H2-TPR. And the performances were tested in a fix...CexZr1-xO2 mixed oxides with different Ce/Zr ratios were prepared by coprecipitation. The characterizations of mixed oxides were studied by X-ray diffraction (XRD) and H2-TPR. And the performances were tested in a fixed-bed quartz reactor. The results indicated that lattice oxygen of CexZr1-xO2 could oxidate methane to syngas and the incorporation of zirconium into the ceria lattice could improve the O2- mobility. The Ce0.7Zr0.3O2 had the best activity in investigative temperature ranging from 600 to 900 ℃. Effects of reaction time on H2/CO ratio were studied at 850 ℃ when using Ce0.7Zr0.3O2 as catalyst. The results indicated that the ratio was closed to 2 values in the first 10 min, however, it rapidly increased with reaction time after >10 min. The possible reason was that the direct partial oxidation of methane reaction was dominant in the first 10 min. However, the methane pyrogenation was responsible for the rapid increase of H2/CO ratio after 10 min. Thus, if syngas with H2/CO ratio of 2 wanted to be obtained, the reaction time needed to be controlled.展开更多
In this paper, Ni/Zr–Yb–O catalysts with different sodium contents are prepared by a co-precipitation method, using aqueous Na2CO3 solution as a precipitant, and the effect of sodium on the catalyst structure and ca...In this paper, Ni/Zr–Yb–O catalysts with different sodium contents are prepared by a co-precipitation method, using aqueous Na2CO3 solution as a precipitant, and the effect of sodium on the catalyst structure and catalytic performance for syngas methanation is extensively investigated using five Ni/Zr–Yb–O catalysts, containing 0, 0.5, 1.5,4.5 and 13.5 wt% Na^+, those are denoted as Cat-1, Cat-2, Cat-3, Cat-4 and Cat-5 respectively. It is found that the interaction between Ni and support determines the catalytic performance of Ni/Zr–Yb–O and the residual sodium content negatively affects the interaction between Ni and support. Cat-1 exhibits an excellent catalytic performance.During a long run time of 380 h, no deactivation is observed and both CO conversion and CH4 selectivity maintain a level above 90%. However, Cat-3 and Cat-5 suffer rapid deactivation under the same reaction condition. The characterization results indicate the strong interaction between Ni and support enables Cat-1 to possess well dispersed Ni species, resistance to sintering and carbon deposition and thus the excellent catalytic performance. However, the presence of sodium ions over Ni/Zr–Yb–O degrades the interaction between Ni and support and the catalytic performance, especially for the stability. The relative weak interaction between Ni and support results in severe sintering of both ZrO2 and Ni under the reaction condition, carbon deposition and the poor catalytic performance.展开更多
CO2 reforming of methane (CDRM) was carried out over MgO supported Ni catalysts with various Ni loadings. The preparation of MgO supported Ni catalysts via surfactant-assisted precipitation method led to the formati...CO2 reforming of methane (CDRM) was carried out over MgO supported Ni catalysts with various Ni loadings. The preparation of MgO supported Ni catalysts via surfactant-assisted precipitation method led to the formation of a nanocrystalline carrier for nickel catalysts. The synthesized samples were characterized by XRD, N2 adsorption-desorption, H2 chemisorption, TPR, TPO and SEM techniques. It was found that the high catalytic activity and stability of the prepared catalysts could be attributable to high dispersion of reduced Ni species and basicity of support surface. In addition, the effect of feed ratio, nickel loading and GHSV on the catalytic performance of CDRM over the catalysts were investigated.展开更多
基金supported by the National Natural Science Foundation of China(21878082).
文摘Radiant syngas cooler(RSC)is widely used as a waste heat recovery equipment in industrial gasification.In this work,an RSC with radiation screens is established and the impact of gaseous radiative property models,gas components,and ash particles on heat transfer is investigated by the numerical simulation method.Considering the syngas components and the pressure environment of the RSC,a modified weighted-sum-of-gray-gases model was developed.The modified model shows high accuracy in validation.In computational fluid dynamics simulation,the calculated steam production is only 0.63%in error with the industrial data.Compared with Smith's model,the temperature decay along the axial direction calculated by the modified model is faster.Syngas components are of great significance to heat recovery capacity,especially when the absorbing gas fraction is less than 10%.After considering the influence of particles,the outlet temperature and the proportion of radiative heat transfer are less affected,but the difference in steam output reaches 2.7 t·h^(-1).The particle deposition on the wall greatly reduces the heat recovery performance of an RSC.
基金National Natural Science Foundation of China(21872101,21962014)Science and Technology Program of Zungeer County,Inner Mongolia(2020YY-12)。
文摘Selective synthesis of ethanol from syngas under the Co-based catalysts is still challenging due to the hard of regulating the active site Co^(0) and Co^(2+)ratio.In this work,a series of CaTi_(0.9-x)Co_(x)Mo_(0.1)O_(3)(x=0,0.1-0.4)and CaTi_(0.7)Co_(0.3)O_(3) catalysts were prepared by using citric acid complexation method to promote the synthesis of ethanol.It was found that Mo species in the perovskite lattice can regulate the Co^(0) and Co^(2+)ratio through the domain-limiting effect of perovskite and the degree of Co reduction could be adjusted by changing the Co/Mo molar ratio.Among these investigated catalysts,the total selectivity of alcohols over the catalyst with the optimal Co/Mo ratio CaTi_(0.6)Co_(0.3)Mo_(0.1)O_(3) reached 39.1%,with ethanol accounting for 74.7%,which was ascribed to the moderate and tightly bound ratio of dissociative to non-dissociative adsorption sites on the surface and the balance of CH_(x)-CH_(y) coupling and C^(O) insertion.
基金supported financially by the National Natural Science Foundation of China(51776206)the Local Innovative and Research Teams Project of Guangdong Pearl River Talents Program(2017BT01N092)+4 种基金the National Key R&D Program of China(2018YFB1501504)the Postgraduate Research&Practice Innovation Program of Jiangsu Province(KYCX20_0095)the Fundamental Research Funds for the Central Universities(3203002104D)the Research Foundation-Flanders(FWO,grant 12E8617N)for funding and KU Leuven grant C14/20/086visiting scholar(2017-20202)at the Guangzhou Institute of Energy Conversion,Chinese Academy of Sciences。
文摘Direct conversion of syngas to aromatics has great potential to decrease fossil fuel dependence.Here,a unique structured hybrid catalyst composed of Fe_(3)O_(4) nanoparticles intimately dispersed inside an acidic zeolite is developed.1 to 4 nm sized Fe_(3)O_(4) nanoparticles end up evenly dispersed in an acidic and slightly mesoporous Al-ZSM-5 based on Fe_(3)O_(4) restructuring during co-hydro thermal synthesis using organosilane modification.A very high aromatic productivity of 214 mmolaromatics h^(-1) gFe^(-1) can be obtained with a remarkable 62%aromatic selectivity in hydrocarbons.This catalyst has excellent sintering resistance ability and maintains stable aromatics production over 570 h.The synthetic insights that postulate a mechanism for the metastable oxide-zeolite reorganization during hydrothermal synthesis could serve as a generic route to sinter-resistant oxide-zeolite composite materials with uniform,well-dispersed oxide nanoparticles in close intimacy with-and partially confined in-a zeolite matrix.
基金financially supported by Key Projects of National Natural Science Foundation of China(No.21736007)National Natural Science Foundation of China(Nos.22078221,21776193,21476155)Top Young Innovative Talents of Shanxi。
文摘In the conversion process of syngas-to-C_(2)species,the OH species are inevitably produced accompanying the production of key intermediates CH_(x)(x=1-3),traditionally,the function of surface OH species is generally accepted as the hydrogenating reactive species.This work for the first time proposed and confirmed the assisted catalytic mechanism of surface OH species that performed as the promoter for syngas-to-C_(2)species on Cu-based catalysts.DFT and microkinetic modeling results reveal that the produced OH species accompanying the intermediates CH_(x)production on the MCu(M=Co,Fe,Rh)catalysts can stably exist to form OH/MCu catalysts,on which the presence of surface OH species as the promoter not only presented better activity and selectivity toward CH_(x)(x=1-3)compared to MCu catalysts,but also significantly suppressed CH_(3)OH production,providing enough CH_(x)sources to favor the production of C_(2)hydrocarbons and oxygenates.Correspondingly,the electronic properties analysis revealed the essential relationship between the electronic feature of OH/MCu catalysts and catalytic performance,attributing to the unique electronic micro-environment of the catalysts under the interaction of surface OH species.This new mechanism is called as OH-assisted catalytic mechanism,which may be applied in the reaction systems related to the generation of OH species.
基金financial support from the National Natural Science Foundation of China(Grant No.21978285,21991093,21991090)the“Transformational Technologies for Clean Energy and Demonstration”,Strategic Priority Research Program of the Chinese Academy of Sciences(Grant No.XDA21030100)。
文摘Direct conversion of syngas to aromatics(STA)over oxide-zeolite composite catalysts is promising as an alternative method for aromatics production.However,the structural effect of the oxide component in composite catalysts is still ambiguous.Herein,we investigate the size effect by selecting ZnCr_(2)O_(4)spinel,as a probe oxide,mixing with H-ZSM-5 zeolite as a composite catalyst for STA reaction.The CO conversion,aromatics selectivity and space-time yield(STY)of aromatics are all significantly improved with the crystal size of ZnCr_(2)O_(4)oxide decreases,which can mainly attribute to the higher oxygen vacancy concentration and thus the rapid generation of more C1oxygenated intermediate species.Based on the understanding of the size-performance relationship,ZnCr_(2)O_(4)-400 with a smaller size mixing with H-ZSM-5 can achieve32.6%CO conversion with 76%aromatics selectivity.The STY of aromatics reaches as high as 4.79 mmol g_(cat)^(-1)h^(-1),which outperforms the previously reported some typical catalysts.This study elucidates the importance of regulating the size of oxide to design more efficient oxidezeolite composite catalysts for conversion of syngas to value-added chemicals.
基金financially supported by Independent Research Subject from Ministry of Science and Technology of China(No.2008BWZ005)
文摘Coral reef-like Ni/Al2O3 catalysts were prepared by co-precipitation of nickel acetate and aluminium nitrate with sodium carbonate aqueous solution in the medium of ethylene glycolye.Methanation of syngas was carried out over coral reef-like Ni/Al2O3 catalysts in a continuous flow type fixed-bed reactor.The structure and properties of the fresh and used catalysts were studied by SEM,N2 adsorption-desorption,XRD,H2-TPR,O2-TPO,TG and ICP-AES techniques.The results showed that the coral reef-like Ni/Al2O3 catalysts exhibited better activity than the conventional Ni/Al2O3-H2O catalysts.The activities of coral reef-like catalysts were in the order of Ni/Al2O3-673Ni/Al2O3-573Ni/Al2O3- 473Ni/Al2O3-773.Ni/Al2O3-673-EG catalyst showed not only good activity and improved stability but also superior resistance to carbon deposition,sintering,and Ni loss.Under the reaction conditions of CO/H2(molar ratio)=1:3,593 K,atmospheric pressure and a GHSV of 2500 h-1,CH4 selectivity was 84.7%,and the CO conversion reached 98.2%.
文摘A series of noble metal catalysts (Ru, Rh, Ir, Pt, and Pd) supported on alumina-stabilized magnesia (Spinel) were used to produce syngas by methane reforming with carbon dioxide. The synthesized catalysts were characterized using BET, TPR, TPO, TPH, and H2S chemisorption techniques. The activity results showed high activity and stability for the Ru and Rh catalysts. The TPO and TPH analyses indicated that the main reason for lower activity and stability of the Pd catalyst was the formation of the less reactive deposited carbon and sintering of the catalyst.
基金supported by the Ministry of Science and Technology of China (No.2017YFB0602201)the Chinese Academy of Sciences (XDA21020400)+2 种基金the National Natural Science Foundation of China (Grant nos.91645204, 21425312 and 21621063)the Youth Innovation Promotion Association of Chinese Academy of Sciences (2019184)the INCOE (International Network of Centers of Excellence) project coordinated by BASF SE
文摘Oxide-Zeolite(OX-ZEO) bifunctional catalyst design concept has been exemplified in several processes to direct conversion syngas to value-added chemicals and fuels such as mixed light olefins, ethylene, aromatics and gasoline.Herein we demonstrate that the product can be steered toward liquefied petroleum gas(LPG) with a selectivity up to 89% in hydrocarbons especially propane selectivity reaching 80% at CO conversion of 63% using ZnCrOx-H-SSZ-39 catalyst.Interestingly, the quantity of the acid sites of SSZ-39 does not influence obviously the hydrocarbon distribution but the strength is crucial for selective formation of propane.This finding provides an alternative route of LPG synthesis from a variety of carbon resources via syngas.
基金The work has been supported by the National High Technology Research and Development Program 863 of China(2011AA050106)the Fundamental Research Funds for the Central Universities(2012YH01).
文摘This research focused on the feasibility of applying the forward and reverse combustion approach to the in situ gasification of lignite with the production of hydrogen-rich syngas(H_(2)and CO).The so-called forward combustion gasification(FCG)and reverse combustion gasification(RCG)approach in which oxygen and steam are simultaneously fed to the simulated system of underground coal gasification(UCG)was studied.A simulated system of UCG was designed and established.The underground conditions of the coal seam and strata were simulated in the system.The combustion gasification of lignite has been carried out experimentally for almost 6.5 days.The average effective content(H_(2)+CO)of syngas during the FCG phase was 62.31%and the maximum content was 70.92%.For the RCG phase the corresponding figures are 61.33%and 67.91%.Thus,the feasibility of using RCG way for UCG has been demonstrated.The temperature profiles have been provided by using of 85 thermocouples during the model experiment,which portrayed the several nephograms of thermal data in the gasifier were of significance for the prospective gasification processes.
基金supported by the National Science and Technology Supporting Plan (No. 2006BAE02B02)
文摘Ni/Al2O3 catalysts with different amounts of manganese ranging from 1 to 3 wt% as promoter were prepared by co-impregnation method. The catalysts were characterized by N2 physisorption, XRD, TPR, SEM and TEM. Their catalytic activity towards syngas methanation reaction was also investigated using a fixed-bed integral reactor. It was demonstrated that the addition of manganese to Ni/Al2O3 catalysts can increase the catalyst surface area and average pore volume, but decrease NiO crystallite size, leading to higher activity and stability. The effects of reaction temperature, pressure and weight hourly space velocity (WHSV) on carbon oxides conversion and CH4 formation rate were also studied. High carbon oxides conversion, CH4 selectivity and formation rate were achieved at the reaction temperature range of 280 300℃.
文摘A series of Cu-based catalysts were developed for alkylation of benzene with syngas. The catalyst samples were prepared by the impregnation method, and were characterized by XRD, XRF, NH3-TPD, and TEM and evaluated in a fixed bed reactor. The optimized reaction temperature of Cu/Al2O3/ZSM-5 catalyst was 350 ℃, while higher contents of copper were conducive to alkylation of benzene with syngas. The new medium strength acid centers in the catalyst created by Cu were beneficial to alkylation. Hydrogenation reaction of CO was executed on the metal centers without dissociation, Dimethyl ether(DME) was the major intermediate over Cu-based catalysts. Higher selectivity of methylation and lower selectivity of heavy aromatics were confirmed after the second metal(Zn, Mn, or V) was added to the copper catalyst. Cu was partly covered by Zn in the Cu-Zn/Al2O3/ZSM-5 catalyst leading to low dispersion and low activity of copper. Cu-Mn/Al2O3/ZSM-5 catalyst possessed the best yield of methylation product. Cu-Mn composite oxides were probably formed in fresh catalyst, which blocked the sintering of Cu in the reaction process. The loading of Cu decreased dramatically after the introduction of V, while causing an increase of the amount of medium strength acid centers at the same time. V prevented the sintering of copper particles during the reducing process and had a promoting effect on the activity of Cu.
基金supported by the Program for Scientific Research Innovation Team in Colleges and Universities of Shandong Provincethe Ph.D.Programs Foundation of Liaocheng University(No.31805)the NSF of China(21263011,21376170)
文摘Cu-Co bi-metal catalysts derived from CuO/LaCoO3 perovskite structure were prepared by one-step citrate complexing method, and the structure evolution reaction from CuO/LaCoO3 to Cu-Co2C/La202CO3 under 1-12 pretreatment was investigated by techniques of XRD, TPR and TEM. The results suggest that a much higher dispersion of copper significantly enhanced the reduction of cobalt, and a stronger interaction between copper and cobalt ions in LaCoO3 particles led to the formation of bi-metallic Cu-Co particles in the reduced catalysts and the enrichment of Co on the surface of bimetallic particles. The prepared catalysts were highly active and selective for the alcohol synthesis from syngas due to the presence of copper-modified C02C species.
文摘In this work,syngas methanation over Ni-W/TiO2-SiO2catalyst was studied in a fluidized-bed reactor(FBR)and its performance was compared with a fixed-bed reactor(FIXBR).The effects of main operating variables including feedstock gases space velocity,coke content,bed temperature and sulfur-tolerant stability of 100 h life were investigated.The structure of the catalysts was characterized by XRD,N2adsorptiondesorption and TEM.It is found that under same space velocity from 5000 h 1to 25000 h 1FBR gave a higher CH4yield,lower coke content,and lower bed temperature than those obtained in FIXBR.Ni-W/TiO2-SiO2catalyst possessed excellent sulfur-tolerant stability on the feedstock gases less than 500 ppm H2S in FBR.The carbon deposits formed on the spent catalyst were in the form of carbon fibers in FBR,while in the form of dense accumulation distribution appearance in FIXBR.
基金supported by the National Natural Science Foundation of China(21673214,U1732272)
文摘The nanosheets structured K–Co–MoS_2 catalyst was prepared through a one-step hydrothermal synthesis combined with the wetness impregnation. The fresh catalyst has a high dispersion of Co–Mo–S active phase and no Co_9S_8 is found. The pure H_2 activated catalyst shows a higher intrinsic activity, especially the C_(2+) OH selectivity for the higher alcohol synthesis compared to the one activated by 5% H_2/N_2 atmosphere. The reason is attributed to that the pure H_2 activation more effectively suppresses the formation of Co_9S_8 and stabilizes the Co–Mo–S active phase during the reaction due to the formation of SH species.
基金the National Natural Science Foundation of China(Nos.U1707603,21878008,21625101,and U1507102,21922801)the Beijing Natural Science Foundation(Nos.2182047 and 2202036)the Fundamental Research Funds for the Central Universities(Nos.XK1802-6,XK1902,12060093063,and 2312018RC07).
文摘Visible-light-driven CO2 photoreduction to achieve renewable materials,such as syngas,hydrocarbons,and alcohols,is a key process that could relieve environmental problems and the energy crisis simultaneously.Reduction of syngas products with diff erent H2:CO proportions is highly expected to produce high value-added chemicals in the industry.However,the development of technologies employing long-wavelength irradiation to achieve CO2 photoreduction and simultaneous tuning of the resultant H2:CO proportion remains a challenging endeavor.In this work,we carried out interfacial engineering by designing a series of heterostructured layered double-hydroxide/MoS2 nanocomposites via electrostatic self-assembly.The syngas proportion(H 2:CO)obtained from CO2 photoreduction could be modulated from 1:1 to 9:1 by visible-light irradiation(λ>400 nm)under the control of the interface-rich heterostructures.This work provides a cost-eff ective strategy for solar-tofuel conversion in an artificial photosynthetic system and describes a novel route to produce syngas with targeted proportions.
基金supported by the Fundamental Research Funds for the Central Universities(XK1802-6,XK1902,XK1803-05,12060093063,2312018RC07)the National Natural Science Foundation of China(U1707603,21878008,21625101,20190816)。
文摘Photocatalytic reduction of CO2 with H2 O to syngas is an effective way for producing high value-added chemical feedstocks such as methanol and light olefins in industry.Nevertheless,the precise control of CO/H2 ratio from photocatalytic CO2 reduction reaction still poses a great challenge for the further application.Herein,we prepared a series of highly efficient heterostructure based on highly dispersed palladium supported on ultrathin Co Al-layered double hydroxide(LDH).In conjunction with a Ru-complex sensitizer,the molar ratios of CO/H2 can be tuned from 1:0.74 to 1:3 under visible-light irradiation(λ>400 nm).More interestingly,the syngas can be obtained under light irradiation atλ>600 nm.Structure characterization and density functional theory calculations revealed that the remarkable catalytic activity can be due to the supported palladium,which improved the charge transfer efficiency.Meanwhile,more H atoms were used to generate H2 on the supported palladium for further tunable CO/H2 ratio.This work demonstrates a new strategy for harnessing abundant solar-energy to produce syngas from a CO2 feedstock.
基金supported by the National Natural Science Foundation of China (NO. 51004060)the Natural Science Foundation of Yunnan Province (NO. 2008E030M, 2010ZC108)+2 种基金the Research Foundation for the Doctoral Program of Higher Education of China (NO. 20095314120005)the Analysis and Test Foundation of Kunming University of Science and Technology (KUST)the 2010 Innovation Foundation of KUST
文摘CeO2 oxygen carrier was prepared by precipitation method and tested by two-step steam reforming of methane (SRM). Two-step SRM for hydrogen and syngas generation is investigated in a fixed-bed reactor. Methane is directly converted to syngas at a H2/CO ratio close to 2 : 1 at a high temperature (above 750 °C) by the lattice oxygen of CeO2; methane cracking is found when the reduction degree of CeO2 was above 5.0% at 850 °C in methane isothermal reaction. CeO2?δ obtained from methane isothermal reaction can split water to generate CO-free hydrogen and renew its lattice oxygen at 700 °C; simultaneously, deposited carbon is selectively oxidized to CO2 by steam following the reaction (C+2H2O→CO2+2H2). Slight deactivation in terms of amounts of desired products (syngas and hydrogen) is observed in ten repetitive two-step SRM process due to the carbon deposition on CeO2 surface as well as sintering of CeO2.
基金the National Natural Science Foundation of China (50574046)National Natural Science Foundationof Major Research Projects (90610035)High School Doctoral Subject Special Science and Research Foundation of Ministry of Education (20040674005)
文摘CexZr1-xO2 mixed oxides with different Ce/Zr ratios were prepared by coprecipitation. The characterizations of mixed oxides were studied by X-ray diffraction (XRD) and H2-TPR. And the performances were tested in a fixed-bed quartz reactor. The results indicated that lattice oxygen of CexZr1-xO2 could oxidate methane to syngas and the incorporation of zirconium into the ceria lattice could improve the O2- mobility. The Ce0.7Zr0.3O2 had the best activity in investigative temperature ranging from 600 to 900 ℃. Effects of reaction time on H2/CO ratio were studied at 850 ℃ when using Ce0.7Zr0.3O2 as catalyst. The results indicated that the ratio was closed to 2 values in the first 10 min, however, it rapidly increased with reaction time after >10 min. The possible reason was that the direct partial oxidation of methane reaction was dominant in the first 10 min. However, the methane pyrogenation was responsible for the rapid increase of H2/CO ratio after 10 min. Thus, if syngas with H2/CO ratio of 2 wanted to be obtained, the reaction time needed to be controlled.
基金Supported by the National Natural Science Foundation of China(21673187,21336009,21576228)National Key Technology Support Program of China(2014BAC10B01).
文摘In this paper, Ni/Zr–Yb–O catalysts with different sodium contents are prepared by a co-precipitation method, using aqueous Na2CO3 solution as a precipitant, and the effect of sodium on the catalyst structure and catalytic performance for syngas methanation is extensively investigated using five Ni/Zr–Yb–O catalysts, containing 0, 0.5, 1.5,4.5 and 13.5 wt% Na^+, those are denoted as Cat-1, Cat-2, Cat-3, Cat-4 and Cat-5 respectively. It is found that the interaction between Ni and support determines the catalytic performance of Ni/Zr–Yb–O and the residual sodium content negatively affects the interaction between Ni and support. Cat-1 exhibits an excellent catalytic performance.During a long run time of 380 h, no deactivation is observed and both CO conversion and CH4 selectivity maintain a level above 90%. However, Cat-3 and Cat-5 suffer rapid deactivation under the same reaction condition. The characterization results indicate the strong interaction between Ni and support enables Cat-1 to possess well dispersed Ni species, resistance to sintering and carbon deposition and thus the excellent catalytic performance. However, the presence of sodium ions over Ni/Zr–Yb–O degrades the interaction between Ni and support and the catalytic performance, especially for the stability. The relative weak interaction between Ni and support results in severe sintering of both ZrO2 and Ni under the reaction condition, carbon deposition and the poor catalytic performance.
文摘CO2 reforming of methane (CDRM) was carried out over MgO supported Ni catalysts with various Ni loadings. The preparation of MgO supported Ni catalysts via surfactant-assisted precipitation method led to the formation of a nanocrystalline carrier for nickel catalysts. The synthesized samples were characterized by XRD, N2 adsorption-desorption, H2 chemisorption, TPR, TPO and SEM techniques. It was found that the high catalytic activity and stability of the prepared catalysts could be attributable to high dispersion of reduced Ni species and basicity of support surface. In addition, the effect of feed ratio, nickel loading and GHSV on the catalytic performance of CDRM over the catalysts were investigated.