Synthesis and Flocculation of Polyacrylamide with Low Water Absorption for Non-dispersible Underwater Concrete

The polyacrylamide which is directly added into concrete shows strong water absorption property.Thus the construction of underwater constructure would demand high amount of water,resulting in poor workability of concrete and strength shrinkage after hardening.Herein,a kind of anionic polyacrylamide(APAM)grafted with water reducing functional group(-COOH)was synthesized at low temperatures by partial factor design and response surface design.The structure and morphology of APAM were characterized by UV,FTIR and SEM methods.The experimental results show that the molecular weight of the synthesized APAM could reach 11 million,under the condition that the temperature was 35℃,the pH value was 8,the monomer concentration was 27wt%,the initiator dosage was 0.6wt%,and the monomer ratio(n(AM):n(AA))was 3.When the APAM was applied into the underwater slurry,it presented good flocculation and low water demand.When the dosage was 1%of the mass of the cement,the water demand increased by 12%,which could meet the self-leveling and anti-dispersity of the underwater slurry at the same time.This technology provides technical guidance for the large-scale industrial production of polyacrylamide for underwater concrete construction while achieving environmental protection during production.

Oxidation of Partially Hydrolyzed Polyacrylamide from Polymer Flooding Processes Using Fenton Reagents

The degradation of partially hydrolyzed polyacrylamide(HPAM) found in alkaline/surfactant/polymer flooding sewage was investigated using Fenton-type reagents. Different Fenton reagent treatments for HPAM degradation were compared. The effects of pH, hydrogen peroxide(H_(2)O_(2)), ferrous ion(Fe^(2+)), and tartaric ion(C_(4)H_(4)O_(6)^(2-)) concentrations were studied. The degradation reaction occurred within a wide range of pH(3–9). The HPAM degradation performance of photo-Fenton processes using solar light and UV were compared with that of the Fenton process. The degradation rate was found to be strongly dependent on the H_(2)O_(2)/Fe^(2+)/C_(4)H_(4)O_(6)^(2-)molar ratio. The HPAM degradation efficiency was 90%, and the chemical oxygen demand removal efficiency was 85%. HPAM could be degraded into a compound with a lower molecular weight, but it was difficult to achieve complete mineralization to CO_(2). The presence of intermediate products hindered further oxidation in the Fenton process.

A review of complications of polyacrylamide hydrogel injection

Once a popular injectable filler,polyacrylamide hydrogel(PAAG)has been banned in China since 2006 due to its unclear safety and long-term complications.However,it is still being used worldwide because of its huge commercial profit,leading to emerging complications and an urgent need for standardized clinical management.This review aimed to assess the properties,safety,and complications of PAAG and treatment strategies for its removal.

Drag reduction behavior of hydrolyzed polyacrylamide/xanthan gum mixed polymer solutions

Partially hydrolyzed polyacrylamide（HPAM）as the main component of slickwater fracturing fluid is a shear-sensitive polymer,which suffers from mechanical degradation at turbulent flow rates.Five different concentrations of HPAM as well as mixtures of polyacrylamide/xanthan gum were prepared to investigate the possibility of improving shear stability of HPAM.Drag reduction（DR）measurements were performed in a closed flow loop.For HPAM solutions,the extent of DR increased from 30%to67%with increasing HPAM concentration from 100 to1000 wppm.All the HPAM solutions suffered from mechanical degradation and loss of DR efficiency over the shearing period.Results indicated that the resistance to shear degradation increased with increasing polymer concentration.DR efficiency of 600 wppm xanthan gum（XG）was 38%,indicating that XG was not as good a drag reducer as HPAM.But with only 6%DR decline,XG solution exhibited a better shear stability compared to HPAM solutions.Mixed HPAM/XG solutions initially exhibited greater DR（40%and 55%）compared to XG,but due to shear degradation,DR%dropped for HPAM/XG solutions.Compared to 200 wppm HPAM solution,addition of XG did not improve the drag reduction efficiency of HPAM/XG mixed solutions though XG slightly improved the resistance against mechanical degradation in HPAM/XG mixed polymer solutions.

Study on purification technology of polyacrylamide wastewater by non-thermal plasma

In this work,non-thermal plasma has been applied to treat polyacrylamide(PAM)wastewater.We have investigated the in fluence of the rule of PAM wastewater initial pH,solution concentration and discharge time,discharge voltage on chemical oxygen demand(COD)degradation rate.At the same time,the effect of pH and discharge time on the viscosity removal rate of PAM solution was also studied.Then,the effect of pH on the viscosity removal rate of 1.0g 1^-1 PAM solution was studied separately.Through orthogonal test,the factors affecting the COD degradation rate of PAM wastewater were determined as follows:discharge time>discharge voltage>solution concentration>wastewater initial pH.1'he COD highest removal rate of PAM wastewater reached 85.74%,when the optimal conditions are as follows:discharge voltage 40 kV,discharge time 5 h,solution concentration 1.0 g 1^-1,pH 1.5.This research provides some basic data and new theoretical basis for PAM wastewater purification.

MONODISPERSE MICRON-SIZED POLYACRYLAMIDE PARTICLES SYNTHESIZED BY DISPERSION POLYMERIZATION

Monodisperse micron-sized polyacrylamide （PAM） particles with a regular shape have been successfully prepared through dispersion polymerization of the monomer using a rotary reactor. FTIR and NMR spectroscopic results demonstrated the formation of PAM. POM and TEM observations revealed that PAM particles had a regular shape and good dispersity. A thick layer of surfactant （PVP） still existed on PAM particles after multiple centrifugation and ultrasonic re-dispersion in ethanol, which indicates a strong interaction between PVP and PAM. The effects of various polymerization factors on the average size of PAM particles have also been studied.

Preparation of cationic polyacrylamide microsphere emulsion and its performance for permeability reduction

In this paper, cationic polyacrylamide microspheres （CPAM） were synthesized using acrylamide （AM） and methacryloyloxyethyl trimethyl ammonium chloride （TMAEMC） as monomers, ammonium sulfate as dispersant, poly（acryloyloxyethyl trimethyl ammonium chloride） （PAETAC） as dispersion stabilizer, and ammonium persulfate as initiator. The synthetic method was dispersion polymerization. The effects of monomer ratio （AM/TMAEMC）, dispersant concentration, and dispersion stabilizer dosage on dispersion polymerization were systematically studied to determine the optimal preparation conditions. The structure and viscosity of the synthesized polymer were characterized by FTIR and capillary viscometry, respectively, and the particle sizes and distribution of the polymer microspheres were characterized by microscopy and dynamic light scattering, respectively. Finally, flow tests were conducted to measure the permeability reduction performance of the microspheres at various concentrations in sand packs with different permeability. Results show that CPAM emulsion of a solids content of 1 wt% has excellent performance in low-to-medium permeability formations （〈 1,000 mD）, and the efficiency may reach above 90%.

Rheological Properties of Hydrophobically Associating Polyacrylamide Solution

A temperature-resistant, salt-tolerant polyacrylamide, hydrophobically associating polymer （HAP）, was synthesized in the State Key Laboratory of Heavy Oil Processing. The rheological behavior of HAP solution was investigated by means of flow experiments in porous media and by using a HAAKE RS600 rheometer. The results of Nuclepore membrane filtration showed that filtration time increased sharply when the critical association concentration was reached. Shear rate had a greater impact on viscosity and shear stress with increasing HAP concentration. The HAP solution with a concentration of 100 mg/L （salinity 32,868 mg/L） exhibited negative thixotropy. However, at the same salinity the HAP solution showed thixotropy and its viscosity became greater when the polymer concentration increased to 1,500 mg/L. The flow experiments in cemented core samples indicated that the resistance factor and residual resistance factor of the HAP solution were 31.8 and 12 when polymer concentration and salinity were 1,500 mg/L, 32,868 mg/L at 85℃ respectively, which is favorable for flooding application. Such factors of partially hydrolyzed polyaerylamide 3530S were merely 3.14 and 1.71, so it could not be applied to polymer flooding in the oilfield with high temperature and high salinity.

Treatment of Wastewater Containing Polyacrylamide Using Three Dimensional Electrodes

A method using three-dimensional electrode is applied to treat wastewater in oil fields, which contains polyacrylamide （PAM）, for analogue. A best condition for electrolysis （I= 1.0 A, t=90 min, c=0.1%, m=980 g,φ=5 mm, d=5.0 cm） has been determined, under which the COD removal efficiency reached 96.0%, COD containing in wastewater reduced to 64.3 mg/L from 1 622.9 mg/L, the figure before treatment. Three categories of PAM-containing wastewater in production practice have been treated with the COD removal ratios being 87.5%, 82.4% and 84.7% respectively. Presence of H2O2 and ·OH are detected by means of Ti（IV）-5-Br-PADAP technique and colorimetry respectively. The concentration is positively proportional to the COD removal ratio and increases in accordance with increment of time of electrolysis and current.

Molecular Simulations of the Effect of Hydrated Montmorillonite on the Viscosity of Polyacrylamide under Confined Shear

Our researches are based on the fact that the systems composed of polyacrylamide and montmorillonite under a kind of shear state often appear in some important practical processes like drilling well etc. The viscosity of polyacrylamide is usually the most important one among the characteristics to decide if the practical processes succeed or not. Therefore, we studied the effect of hydrated montmorillonite on the viscosities of polyacrylamide with temperature and shear rate varying under confined shear by molecular simulation method. Adopting the condition of confined shear in the research could make our simulations and the practical processes as similar as possible. First, the model of one polyacrylamide polymer chain with 20 monomers linearly linking surrounded by water molecules between two of montmorillonite layers was constructed. Then canonical ensemble （NVT） MD simulations were carried out for the built model at different temperatures and shear rates. From the gained simulation results, we calculated the polymer＇s structural property-radius of gyration, which was directly related to the viscosity property of polyacrylamide polymer. It was found that the viscosity of the polyacrylamide polymer between hydrated clay layers decreased with the temperature increasing from 298 to 343 K under the condition of confined shear. The variation trend of viscosity from simulation results was also confirmed by our experiments. Besides, the viscosity of the polyacrylamide between hydrated clay layers decreased with the shear rate increasing within the range of higher shear rates.

Determination of the Structure of Polyacrylamide/Aluminum Citrate Colloidal Dispersion Gel System

1 INTRODUCTIONIn recent years,colloidal dispersion gel(CDG)have been attracting more and more in thefield of enhanced oil recovery on account of the cost-effectiveness and high efficiency ofblocking formation.Compared with bulk gel(BG),CDG exhibits lower polymer concentra-tion,undefined shape and selective blocking formation characteristics.The characteris-tics of CDG and BG are related to structure.In the bulk gel a continuous network of polymermolecules is formed predominant through intermolecular cross-linkages.The

Preparation of Dysprosium Ferrite/Polyacrylamide Magnetic Composite Microsphere and Its Characterization

Using the technique of microemulsion polymerization with nano-reactor, dysprosium ferrite/polyacrylamide magnetic composite microsphere was prepared by one-step method in a single inverse microemulsion. The structure, average particle size, morphology of composite microsphere were characterized by FTIR, XRD, TEM and TGA. The magnetic responsibility of composite microsphere was also investigated. The results indicate that the magnetic composite microsphere possess high magnetic responsibility and suspension stability.

Synthesis,Characterization and Electromagnetic Studies on Nanocrystalline Nickel Zinc Ferrite by Polyacrylamide Gel

Nanocrystalline nickel zinc ferrite powders （Ni=Zn1-xFe2O4, A for x=0, B for x=0.2, C for x=0.5, D for x= 0.8 and E for x= 1） were synthesized by polyacrylamide gel method. X-ray diffraction （XRD）, transmission electron microscopy （TEM） and wave-guide were used to characterize the composition. The XRD results show that the dried gel powders are amorphous, and the characteristic peaks of the spinel Ni0.5Zn0.5Fe2O4 appear after the gel is calcined at 400℃ for 1 h. When the calcining temperatures are 600 and 800℃, the average grain sizes are identified by TEM to be 10 and 30 nm, respectively. The NixZn1-xFe2O4 powders have both dielectric loss and magnetic loss in the frequency range of 8.2-11.0GHz. With the increase of Ni^2＋ ions content, the dielectric parameters （ε′） and permeability （u′） of the NixZn1-xFe2O4 powders decrease while the dielectric loss （ε″）, magnetic loss （u″） and the reflection loss increase.

Determination of Residual Acrylamide in Medical Polyacrylamide Hydrogel by High Performance Liquid Chromatography tandem Mass Spectroscopy

Objective To determine residual acrylamide in medical polyacrylamide hydrogel by high performance liquid chromatography tandem mass spectroscopy （HPLC-MS）. Methods After 13C3 labeled acrylamide was added, the sample was extracted with water and then cleaned up with ExtrelutTM 20. The polyacrylamide hydrogel sample and 20 clinical cases were analyzed by HPLC-MS/MS and isotope dilution quantifying technique in selected reaction monitoring （SRM） mode. Results Acrylamide was separated from polyacrylamide hydrogel. The concentration of acrylamide in polyacrylamide hydrogel ranged from 3.9×10^-9 to 3.1×10^- 8g/L in the 20 clinical cases. The peak area was favorable linear and the range was up to 3 000 μg/L. The recovery rate was 103.1% with a relative standard deviation （RSD） of 6.20%, when the mark level was 50 lag/L. Conelusion HPLC-MS is a rapid, accurate, and sensitive method for the determination of residual acrylamide in medical polyacrylamide hydrogel.

Synthesis of YAG∶Ce^(3+) Phosphor by Polyacrylamide Gel Method and Promoting Action of α-Al_2O_3 Seed Crystal on Phase Formation

YAG： Ce^3 ＋ phosphor particles were prepared using polyacrylamide gel method. The structure evolution of powders during annealing process was followed by X-ray diffraction determination. It is found that some intermediate phases, including θ-Al2O3, YAM and YAP, are formed when calcining polyacrylamide gel, however, the pure YAG phase can be formed directly when calcining polyacrylamide gel with α-Al2O3 as seed crystal. These facts show that the existence of α- Al2O3 seed crystal can block the formation of θ-Al2O3, YAM and YAP, and accelerate its reaction with Y2O3 to form YAG phase directly at lower temperature. The emission peak of prepared YAG ： Ce^3 ＋ phosphor is wide with maximum at 550 nm and the exitation band has two peaks, the major one is around at 460 nm, which matches the blue emission of GaN LED and is suitable for the assemble of white LED. Some fluxes can enhance the photoluminescence intensity of phosphor particles, that can be attributed both to the improvement of crystallization processes of YAG and to the stabilization of trivalence cerium ion in YAG：Ce^3 ＋.

Electrically induced gel-sol transition of polyvinyl alcohol/polyacrylamide semi-interpenetrated hydrogels

Polyvinyl alcohol/polyacrylamide semi-interpenetrated hydrogels were prepared via freeze-thaw process. When a 20 V of DC was applied across the gels, the gels with lower polyacrylamide content underwent a contraction or partly turned into solution, while for the gels. with higher polyacrylamide concentration, a complete gel-sol transition was observed in a short time.

Synthesis,Characterization and Electromagnetic Studies on Nanocrystalline Co_(0.5)Zn_(0.5)Fe_2O_4 Synthesized by Polyacrylamide Gel

Nanocrystalline Co0.5Zn0.5Fe2O4 ferrite was synthesized by polyacrylamide gel method. The electromagnetic and microwave absorption properties of the ferrite were investigated. The results indicated that calcining temperature of the ferrite had a significant influence on the effective properties of the ferrite. When the calcining temperature was 500, 600 and 700℃, the average size of particles was 10, 30 and 80 nm, respectively. The dielectric loss （ε″） and magnetic loss （μ″） of the ferrite was around 0.65 and 0.29 at 8.2 GHz, respectively. Microwave absorption properties of the ferrites were simultaneously influenced due to the strong correlation between reflection loss and electromagnetic parameters of the ferrite.

Preparation and determination of hydroximic polyacrylamide

A new kind of polyacrylamide derivate, hydroximic polyacrylamide (HPAM), was prepared from polyacrylamide (PAM) with hydroxylamine hydrochloride in KOH/alcohol solution. Based on colorimetric method in the measurement of C 7 9 alkyl hydroximic acid, the substitution degree of HPAM was determined by selecting octyl hydroximic acid as a primary standard substance. The effects of temperature, the amount of hydroxylamine and potassium hydroxide, and the reaction time on the reaction are discussed. HPAM with 5.78% substitution of degree was acquired by optimizing the reaction conditions. IR spectra revealed that tautomerism appears in the HPAM, and that HPAM exists in both the forms of hydroxamic type and hydroximic type, and the latter type can easily lead to the forming of intramolecular hydrogen bond.

A pH-sensitive Modified Polyacrylamide Hydrogel

A pH-sensitive modified polyacrylamide hydrogel was prepared by two steps and the modified polyacrylamide was characterized by ^1HNMR spectrum. The surface morphology and swelling behavior of the hydrogels were investigated.

CONDUCTIVITY BEHAVIOR OF IONIC Al(OH)_3-POLYACRYLAMIDE HYBRIDS IN AQUEOUS SOLUTIONS

The conductivity behavior of Al(OH)3-acrylamide hybrid polyacrylamide (hybrid PAAm) in distilled water was studied. A discontinuity phenomenon of the conductivity (k) versus concentration (c) curve of the hybrid PAAm in a certain concentration regime is found. This phenomenon is dependent on the molecular weight of the hybrid PAAm and on the particle size and content of the Al(OH)3 colloid in the hybrid PAAm. This phenomenon was accounted for assuming ionization of the hybrid PAAm.