The study of the dynamic disaster mechanism of coal and gas outburst two-phase flow is crucial for improving disaster reduction and rescue ability of coal mine outburst accidents.An outburst test in a T-shaped roadway...The study of the dynamic disaster mechanism of coal and gas outburst two-phase flow is crucial for improving disaster reduction and rescue ability of coal mine outburst accidents.An outburst test in a T-shaped roadway was conducted using a self-developed large-scale outburst dynamic disaster test system.We investigated the release characteristics of main energy sources in coal seam,and obtained the dynamic characteristics of outburst two-phase flow in a roadway.Additionally,we established a formation model for outburst impact flow and a model for its flow in a bifurcated structure.The results indicate that the outburst process exhibits pulse characteristics,and the rapid destruction process of coal seam and the blocking state of gas flow are the main causes of the pulse phenomenon.The outburst energy is released in stages,and the elastic potential energy is released in the vertical direction before the horizontal direction.In a straight roadway,the impact force oscillates along the roadway.With an increase in the solid–gas ratio,the two-phase flow impact force gradually increases,and the disaster range extends from the middle of the roadway to the coal seam.In the area near the coal seam,the disaster caused by the two-phase flow impact is characterized by intermittent recovery.In a bifurcated roadway,the effect of impact airflow on impact dynamic disaster is much higher than that of two-phase flow,and the impact force tends to weaken with increasing solid-gas ratio.The impact force is asymmetrically distributed;it is higher on the left of the bifurcated roadway.With an increase in the solid-gas ratio,the static pressure rapidly decreases,and the bifurcated structure accelerates the attenuation of static pressure.Moreover,secondary acceleration is observed when the shock wave moves along the T-shaped roadway,indicating that the bifurcated structure increases the shock wave velocity.展开更多
The general solution of stresses is derived for a T-shaped junction of two thin plates with an adhesion crack. The plates are orthotropic. A shear force is applied on the crack surface. The analysis is based on the su...The general solution of stresses is derived for a T-shaped junction of two thin plates with an adhesion crack. The plates are orthotropic. A shear force is applied on the crack surface. The analysis is based on the supposition that the stresses in each plate can be approximated by a plane stress condition. The results obtained are verified by numerical calculation of FEM.展开更多
This study examines the design provisions of the Chinese GB 50011-2010 code for seismic design of buildings for the special boundary elements of T-shaped reinforced concrete walls and proposes an improved design metho...This study examines the design provisions of the Chinese GB 50011-2010 code for seismic design of buildings for the special boundary elements of T-shaped reinforced concrete walls and proposes an improved design method. Comparison of the design provisions of the GB 50011-2010 code and those of the American code ACI 318-14 indicates a possible deficiency in the T-shaped wall design provisions in GB 50011-2010. A case study of a typical T-shaped wall designed in accordance with GB 50011-2010 also indicates the insufficient extent of the boundary element at the non-flange end and overly conservative design of the flange end boundary element. Improved designs for special boundary elements ofT-shaped walls are developed using a displacement-based method. The proposed design formulas produce a longer boundary element at the non-flange end and a shorter boundary element at the flange end, relative to those of the GB 50011-2010 provisions. Extensive numerical analysis indicates that T-shaped walls designed using the proposed formulas develop inelastic drift of 0.01 for both cases of the flange in compression and in tension.展开更多
In this study, nonlinear static and dynamic responses of a microcantilever with a T-shaped tip mass excited by electrostatic actuations are investigated. The electrostatic force is generated by applying an electric vo...In this study, nonlinear static and dynamic responses of a microcantilever with a T-shaped tip mass excited by electrostatic actuations are investigated. The electrostatic force is generated by applying an electric voltage between the horizontal part of?T-shaped tip mass and an opposite electrode plate. The cantilever microbeam is modeled as an Euler-Bernoulli beam. The T-shaped tip mass is assumed to be a rigid body and the nonlinear effect of electrostatic force is considered. An equation of motion and its associated boundary conditions are derived by the aid of combining the Hamilton principle and Newton’s method. An exact solution is obtained for static deflection and mode shape of vibration around the static position. The differential equation of nonlinear vibration around the static position is discretized using the Galerkin method. The system mode shapes are used as its related comparison functions. The discretized equations are solved by the perturbation theory in the neighborhood of primary and subharmonic resonances. In addition, effects of mass inertia, mass moment of inertia as well as rotation of the T-shaped mass, which were ignored in previous works, are considered in the analysis. It is shown that by increasing the length of the horizontal part of the T-shaped mass, the amount of static deflection increases, natural frequency decreases and nonlinear shift of the resonance frequency increases. It is concluded that attaching an electrode plate with a T-shaped configuration to the end of the cantilever microbeam results in a configuration with larger pull-in voltage and smaller nonlinear shift of the resonance frequency compared to the configuration in which the electrode plate is directly attached to it.展开更多
An analytical procedure is presented to evaluate the fluid sloshing characteristics in a two-dimensional(2D)rectangular container with a bottom-mounted T-shaped baffle.The fluid region is divided into several sub-doma...An analytical procedure is presented to evaluate the fluid sloshing characteristics in a two-dimensional(2D)rectangular container with a bottom-mounted T-shaped baffle.The fluid region is divided into several sub-domains with hypothetical interfaces and the velocities and pressures of the fluid on adjacent interfaces should be identical.The separation of variables in conjunction with the superposition principle is employed to formulate the velocity potential of each sub-domain.The Fourier series expansion is used to derive the eigenvalue equation by substituting the velocity potential solutions into the free surface conditions and the continuity conditions on adjacent interfaces.Under the horizontal base excitation,the total velocity potential of fluid is decomposed of the impulsive and perturbed velocity potentials.The orthogonality of the sloshing modes is demonstrated by implementing Gauss formula.The dynamic response equation is established by incorporating the total velocity potential solution into the surface wave equation.Excellent agreements are achieved between the present results and those from the reported literature and finite element code.Numerical results are exhibited to reveal the effect of the baffle parameters and excitation frequency on sloshing characteristics and responses of liquid.展开更多
A series of liquid crystalline polymers with T-shaped two-dimensional mesogenic unitswere synthesized via low temperature solution polycondensation of 2-(4'-alkoxy-phenyl)hydroquinone with various diacyl dichlorid...A series of liquid crystalline polymers with T-shaped two-dimensional mesogenic unitswere synthesized via low temperature solution polycondensation of 2-(4'-alkoxy-phenyl)hydroquinone with various diacyl dichlorides. The polymers were found to be nematic andshown thermotropic liquid crystalline behaviors through observations using DSC, polarizedmicroscopy and X-ray diffraction. The melting temperature T_m and the isotropizationtemperature T_i of the polymers change regularly with varying of the monomer structures.展开更多
A novel series of liquid crystalline copolyesters with T-shaped two-dimensional mesogenic unit and crown ether cycle of cis-4,4′-bis(4-hydroxyphenylazo)dibenzo-18-crown-6 was prepared via solution condensation polyme...A novel series of liquid crystalline copolyesters with T-shaped two-dimensional mesogenic unit and crown ether cycle of cis-4,4′-bis(4-hydroxyphenylazo)dibenzo-18-crown-6 was prepared via solution condensation polymerization from 4,4′-(α,ω-hexanedioyloxy)dibenzoyl dichloride(M_1),2-(4′-ethoxyphenyl)hydroquinone(M_2)and cis-4,4′-bis(4- hydroxyphenylazo)dibenzo-18-crown-6(M_3).The molecular weights of copolyesters are not high,and the intrinsic viscosity [η]of copolyesters ranges from 0.29-0.43.The monomers ...展开更多
A novel vertical InN/InGaN heterojunction tunnel FET with hetero T-shaped gate as well as polarization-doped source and drain region(InN-Hetero-TG-TFET)is proposed and investigated by Silvaco-Atlas simulations for the...A novel vertical InN/InGaN heterojunction tunnel FET with hetero T-shaped gate as well as polarization-doped source and drain region(InN-Hetero-TG-TFET)is proposed and investigated by Silvaco-Atlas simulations for the first time.Compared with the conventional physical doping TFET devices,the proposed device can realize the P-type source and N-type drain region by means of the polarization effect near the top InN/InGaN and bottom InGaN/InN heterojunctions respectively,which could provide an effective solution of random dopant fluctuation(RDF)and the related problems about the high thermal budget and expensive annealing techniques due to ion-implantation physical doping.Besides,due to the hetero T-shaped gate,the improvement of the on-state performance can be achieved in the proposed device.The simulations of the device proposed here in this work show ION of 4.45×10^(-5)A/μm,ION/IOFF ratio of 10^(13),and SS_(avg)of 7.5 mV/dec in InN-Hetero-TG-TFET,which are better than the counterparts of the device with a homo T-shaped gate(InN-Homo-TG-TFET)and our reported lateral polarization-induced InN-based TFET(PI-InN-TFET).These results can provide useful reference for further developing the TFETs without physical doping process in low power electronics applications.展开更多
A new series of liquid crystal polyesters with T-shaped two-dimensional mesogenic units weresynthesized by melt polycondensation of the diacetates of 2-(4'-alkoxy -phenyl)-hydroquinones with 4,4'-alkylenedioxy...A new series of liquid crystal polyesters with T-shaped two-dimensional mesogenic units weresynthesized by melt polycondensation of the diacetates of 2-(4'-alkoxy -phenyl)-hydroquinones with 4,4'-alkylenedioxydibenzoic acid. The polymers were characterized by using polarized microscopy, DSC and X-ray diffraction. It was realized that all the polymers have nematic thermotropic liquid crystallinecharacteristics. The melting temperature (T_m) and isotropization temperature (T_i) of the polymers changeregularly with varying lengths of the alkoxy side group and the length of the alkylene group in the main chainin company with an even-odd effect. The mesophase temperature range also varies regularly with the polymerstructure. It is shown that the mesophase range has been widened.展开更多
This paper proposes,demonstrates,and describes a basic T-shaped Multi-Input and Multi-Output(MIMO)antenna with a resonant frequency of 3.1 to 10.6 GHz.Compared with the U-shaped antenna,the mutual coupling is minimize...This paper proposes,demonstrates,and describes a basic T-shaped Multi-Input and Multi-Output(MIMO)antenna with a resonant frequency of 3.1 to 10.6 GHz.Compared with the U-shaped antenna,the mutual coupling is minimized by using a T-shaped patch antenna.The T-shaped patch antenna shapes filter properties are tested to achieve separation over the 3.1 to 10.6 GHz frequency range.The parametric analysis,including width,duration,and spacing,is designed in the MIMO applications for good isolation.On the FR4 substratum,the configuration of MIMO is simulated.The appropriate dielectric material ε_(r)=4.4 is introduced using this contribution and application array feature of the MIMO systems.In this paper,FR4 is used due to its high dielectric strength and low cost.For 3.1 to 10.6 GHz and 3SRR,T-shaped patch antennas are used in the field to increase bandwidth.The suggested Tshaped MIMO antenna is calculated according to the HFSS 13.0 program simulation performances.The antenna suggested is,therefore,a successful WLAN candidate.展开更多
A compact CPW-fed double T-Shaped antenna is proposed for dual-band wireless local area network (WLAN) operations. For the proposed antenna, the -10 dB return loss bandwidth could reach about 25.5% for the 2.4 GHz ban...A compact CPW-fed double T-Shaped antenna is proposed for dual-band wireless local area network (WLAN) operations. For the proposed antenna, the -10 dB return loss bandwidth could reach about 25.5% for the 2.4 GHz band and 5.7 % for the 5 GHz band, which meet the required bandwidth specification of WLAN standard. To reduce the mutual coupling and get high isolation between two dual-band antennas, we proposed the novel electromagnetic band gap (EBG) structures. When the EBG structure is employed, a -13dB and -30dB mutual coupling reduction is achieved at 2.4 and 5.2 GHz. It shows that the features of small size, uniplanar structure, good radiation characteristics and small mutual coupling are promising for multi-input multi-output (MIMO) applications.展开更多
A new T-shaped tunnel field-effect transistor(TTFET) with gate dielectric spacer(GDS) structure is proposed in this paper. To further studied the effects of GDS structure on the TTFET, detailed device characteristics ...A new T-shaped tunnel field-effect transistor(TTFET) with gate dielectric spacer(GDS) structure is proposed in this paper. To further studied the effects of GDS structure on the TTFET, detailed device characteristics such as current-voltage relationships, energy band diagrams, band-to-band tunneling(BTBT) rate and the magnitude of the electric field are investigated by using TCAD simulation. It is found that compared with conventional TTFET and TTFET with gate-drain overlap(GDO) structure, GDS-TTFET not only has the minimum ambipolar current but also can suppress the ambipolar current under a more extensive bias range. Furthermore, the analog/RF performances of GDS-TTFET are also investigated in terms of transconductance, gate-source capacitance, gate-drain capacitance, cutoff frequency, and gain bandwidth production. By inserting a low-κ spacer layer between the gate electrode and the gate dielectric, the GDS structure can effectively reduce parasitic capacitances between the gate and the source/drain, which leads to better performance in term of cutoff frequency and gain bandwidth production. Finally, the thickness of the gate dielectric spacer is optimized for better ambipolar current suppression and improved analog/RF performance.展开更多
To automatically detect oil tanks in polarimetric synthetic aperture radar(SAR) images, a coastal oil tank detection method is proposed based on recognition of T-shaped harbor. First of all, the T-shaped harbor is d...To automatically detect oil tanks in polarimetric synthetic aperture radar(SAR) images, a coastal oil tank detection method is proposed based on recognition of T-shaped harbor. First of all, the T-shaped harbor is detected to locate the region of interest(ROI) of oil tanks. Then all suspicious targets in the ROI are extracted by the segmentation of strong scattering targets and the classifier of H/α. The template targets are selected from the suspicious targets by the combination of a proposed circular degree parameter and the similarity parameter(SP) of the polarimetric coherency matrix. Finally, oil tanks are detected according to the statistics of the similarity parameter between each suspicious target and template targets in ROI. Polarimetric SAR data acquired by RADARSAT-2 over Berkeley and Singapore areas are used for testing. Experiment results show that most of the targets are correctly detected and the overall detection rate is close to 80%.The false rate is effectively reduced by the proposed algorithm compared with the method without T-shaped harbor recognition.展开更多
Traditional preparation of magnetic microcapsules involves cumbersome processes and often results in irregular-shaped products. Due to the stable laminar flow of reaction solution and the moderate reaction conditions,...Traditional preparation of magnetic microcapsules involves cumbersome processes and often results in irregular-shaped products. Due to the stable laminar flow of reaction solution and the moderate reaction conditions, the T-shaped microchannel (T-MC) reactor is supposed to yield microcapsules with regular shape. In this paper, magnetic particles of ferroferric oxide modified by oleic acid (OA-Fe3O4) and dispersed in tetrachloroethylene were used as core material. Polymethyl methacrylate (PMMA) was used as shell material. Magnetic microcapsules were prepared by using a T-MC reactor. Factors that influenced the encapsulated reaction were investigated in details, which included the velocity ratio of aqueous phase to oil phase, the length and the inner diameter of the microchannel. The morphology, composition, and magnetic responsiveness of the magnetic microcapsules were analyzed and characterized by SEM, FTIR, XRD, TGA, and vibrating sample magnetometer (VSM). The results confirmed that magnetic microcapsules prepared by T-MC reactor were regular in shape.展开更多
Two series of new liquid crystalline polymers with T-shaped two-dimensional mesogenic units were synthesized by low temperature solution polycondensations of 4-substituted N-2, 5-dihydroxybenzylidene aniline monomers ...Two series of new liquid crystalline polymers with T-shaped two-dimensional mesogenic units were synthesized by low temperature solution polycondensations of 4-substituted N-2, 5-dihydroxybenzylidene aniline monomers with different diacyl dichlorides. The polymers were found to be nematic and shown liquid crystalline behavior. The melting temperature T-m and the clearing temperature T-i of the polymers change regularly with varying of the monomer structures.展开更多
By utilizing a Fabry–Perot (FP) nanocavity adjacent to T-shaped gap waveguide ports, spectrally selective filtering is realized. When the wavelength of incident light corresponds to the resonance wavelength of the ...By utilizing a Fabry–Perot (FP) nanocavity adjacent to T-shaped gap waveguide ports, spectrally selective filtering is realized. When the wavelength of incident light corresponds to the resonance wavelength of the FP nanocavity, the surface plasmons are captured inside the nanocavity, and light is highly reflected from this port. The resonance wavelength is determined by using Fabry–Perot resonance condition for the nanocavity. For any desired filtering frequency the dimension of the nanocavity can be tailored. The numerical results are based on the two-dimensional finite difference time domain simulation under a perfectly matched layer absorbing boundary condition. The analytical and simulation results indicate that the proposed structure can be utilized for filtering and splitting applications.展开更多
In order to effectively solve the dead-zone and low-precision of T-shaped transmission line fault location,a new T-shaped transmission line fault location algorithm based on phase-angle jump checking is proposed in th...In order to effectively solve the dead-zone and low-precision of T-shaped transmission line fault location,a new T-shaped transmission line fault location algorithm based on phase-angle jump checking is proposed in this paper.Firstly,the 3-terminal synchronous fundamental positive sequence voltage and current phasors are extracted and substituted into the fault branch distance function to realize the selection of fault branch when the fault occurs;Secondly,use the condition of the fundamental positive sequence voltage phasor at the fault point is equal to calculate all roots(including real root and virtual roots);Finally,the phase-angle jump check function is used for checking calculation,and then the only real root can be determined as the actual fault distance,thereby achieving the purpose of high-precision fault location.MATLAB simulation results show that the proposed new algorithm is feasible and effective with high fault location accuracy and good versatility.展开更多
A novel A1GaN/GaN high electron mobility transistor (HEMT) with a source-connected T-shaped field-plate (ST-FP HEMT) is proposed for the first time in this paper. The source-connected T-shaped field-plate (ST-FP...A novel A1GaN/GaN high electron mobility transistor (HEMT) with a source-connected T-shaped field-plate (ST-FP HEMT) is proposed for the first time in this paper. The source-connected T-shaped field-plate (ST-FP) is composed of a source-connected field-plate (S-FP) and a trench metal. The physical intrinsic mechanisms of the ST-FP to improve the breakdown voltage and the FP efficiency and to modulate the distributions of channel electric field and potential are studied in detail by means of two-dimensional numerical simulations with Silvaco-ATLAS. A comparison to the HEMT and the HEMT with an S-FP (S-FP HEMT) shows that the ST-FP HEMT could achieve a broader and more uniform channel electric field distribution with the help of a trench metal, which could increase the breakdown voltage and the FP efficiency remarkably. In addition, the relationship between the structure of the ST-FP, the channel electric field, the breakdown voltage as well as the FP efficiency in ST-FP HEMT is analyzed. These results could open up a new effective method to fabricate high voltage power devices for the power electronic applications.展开更多
The bubble formation dynamics and size manipulation in the slurry of polystyrene microspheres in the microfluidic T-junction were visually investigated by a high-speed camera.Based on the evolution of the bubble neck ...The bubble formation dynamics and size manipulation in the slurry of polystyrene microspheres in the microfluidic T-junction were visually investigated by a high-speed camera.Based on the evolution of the bubble neck with time,the formation process of bubbles is divided into three stages:filling,squeezing and pinch-off.The particle concentration has an obvious effect on the squeezing stage,while less impact on the filling and pinch-off stages.In the squeezing stage,the evolution of the dimensionless minimum neck width of bubbles with time could be described by a power-law relationship.The increase of the particle concentration or continuous phase flow rate could lead to the increase of body flow of the continuous phase and the enhancement of the squeezing force acted on the bubble neck,correspondingly,the power-law index a in the squeezing stage enlarges.Moreover,the bubble size increases with the increase of the gas phase flow rate and the decrease of the particle concentration and continuous phase flow rate.However,the effect of the particle concentration on the bubble size weakens with the increase of the continuous phase flow rate.In addition,a new prediction correlation of the bubble size for the slurry system in a T-shape microchannel was proposed with good prediction accuracy.展开更多
Parasitic capacitances associated with overhangs of the T-shape-gate enhancement-mode(E-mode)GaN-based power device,were investigated by frequency/voltage-dependent capacitance-voltage and inductive-load switching mea...Parasitic capacitances associated with overhangs of the T-shape-gate enhancement-mode(E-mode)GaN-based power device,were investigated by frequency/voltage-dependent capacitance-voltage and inductive-load switching measurements.The overhang capacitances induce a pinch-off voltage distinguished from that of the E-mode channel capacitance in the gate capacitance and the gatedrain capacitance characteristic curves.Frequency-and voltage-dependent tests confirm the instability caused by the trapping of interface/bulk states in the LPCVD-SiNx passivation dielectric.Circuit-level double pulse measurement also reveals its impact on switching transition for power switching applications.展开更多
基金This work was supported by the National Natural Science Foundation of China(Nos.51874055,52074047,and 52064016).
文摘The study of the dynamic disaster mechanism of coal and gas outburst two-phase flow is crucial for improving disaster reduction and rescue ability of coal mine outburst accidents.An outburst test in a T-shaped roadway was conducted using a self-developed large-scale outburst dynamic disaster test system.We investigated the release characteristics of main energy sources in coal seam,and obtained the dynamic characteristics of outburst two-phase flow in a roadway.Additionally,we established a formation model for outburst impact flow and a model for its flow in a bifurcated structure.The results indicate that the outburst process exhibits pulse characteristics,and the rapid destruction process of coal seam and the blocking state of gas flow are the main causes of the pulse phenomenon.The outburst energy is released in stages,and the elastic potential energy is released in the vertical direction before the horizontal direction.In a straight roadway,the impact force oscillates along the roadway.With an increase in the solid–gas ratio,the two-phase flow impact force gradually increases,and the disaster range extends from the middle of the roadway to the coal seam.In the area near the coal seam,the disaster caused by the two-phase flow impact is characterized by intermittent recovery.In a bifurcated roadway,the effect of impact airflow on impact dynamic disaster is much higher than that of two-phase flow,and the impact force tends to weaken with increasing solid-gas ratio.The impact force is asymmetrically distributed;it is higher on the left of the bifurcated roadway.With an increase in the solid-gas ratio,the static pressure rapidly decreases,and the bifurcated structure accelerates the attenuation of static pressure.Moreover,secondary acceleration is observed when the shock wave moves along the T-shaped roadway,indicating that the bifurcated structure increases the shock wave velocity.
文摘The general solution of stresses is derived for a T-shaped junction of two thin plates with an adhesion crack. The plates are orthotropic. A shear force is applied on the crack surface. The analysis is based on the supposition that the stresses in each plate can be approximated by a plane stress condition. The results obtained are verified by numerical calculation of FEM.
基金International Science&Technology Cooperation Program of China under Grant No.2014DFA70950Tsinghua University Initiative Scientific Research Program under Grant No.2012THZ02-1National Natural Science Foundation of China under Grant No.91315301
文摘This study examines the design provisions of the Chinese GB 50011-2010 code for seismic design of buildings for the special boundary elements of T-shaped reinforced concrete walls and proposes an improved design method. Comparison of the design provisions of the GB 50011-2010 code and those of the American code ACI 318-14 indicates a possible deficiency in the T-shaped wall design provisions in GB 50011-2010. A case study of a typical T-shaped wall designed in accordance with GB 50011-2010 also indicates the insufficient extent of the boundary element at the non-flange end and overly conservative design of the flange end boundary element. Improved designs for special boundary elements ofT-shaped walls are developed using a displacement-based method. The proposed design formulas produce a longer boundary element at the non-flange end and a shorter boundary element at the flange end, relative to those of the GB 50011-2010 provisions. Extensive numerical analysis indicates that T-shaped walls designed using the proposed formulas develop inelastic drift of 0.01 for both cases of the flange in compression and in tension.
文摘In this study, nonlinear static and dynamic responses of a microcantilever with a T-shaped tip mass excited by electrostatic actuations are investigated. The electrostatic force is generated by applying an electric voltage between the horizontal part of?T-shaped tip mass and an opposite electrode plate. The cantilever microbeam is modeled as an Euler-Bernoulli beam. The T-shaped tip mass is assumed to be a rigid body and the nonlinear effect of electrostatic force is considered. An equation of motion and its associated boundary conditions are derived by the aid of combining the Hamilton principle and Newton’s method. An exact solution is obtained for static deflection and mode shape of vibration around the static position. The differential equation of nonlinear vibration around the static position is discretized using the Galerkin method. The system mode shapes are used as its related comparison functions. The discretized equations are solved by the perturbation theory in the neighborhood of primary and subharmonic resonances. In addition, effects of mass inertia, mass moment of inertia as well as rotation of the T-shaped mass, which were ignored in previous works, are considered in the analysis. It is shown that by increasing the length of the horizontal part of the T-shaped mass, the amount of static deflection increases, natural frequency decreases and nonlinear shift of the resonance frequency increases. It is concluded that attaching an electrode plate with a T-shaped configuration to the end of the cantilever microbeam results in a configuration with larger pull-in voltage and smaller nonlinear shift of the resonance frequency compared to the configuration in which the electrode plate is directly attached to it.
基金The study was financially supported by the National Natural Science Foundation of China(Grant No.51978336)the Science and Technology Project of Water Resources Department of Jiangsu Province(Grant No.2021022).
文摘An analytical procedure is presented to evaluate the fluid sloshing characteristics in a two-dimensional(2D)rectangular container with a bottom-mounted T-shaped baffle.The fluid region is divided into several sub-domains with hypothetical interfaces and the velocities and pressures of the fluid on adjacent interfaces should be identical.The separation of variables in conjunction with the superposition principle is employed to formulate the velocity potential of each sub-domain.The Fourier series expansion is used to derive the eigenvalue equation by substituting the velocity potential solutions into the free surface conditions and the continuity conditions on adjacent interfaces.Under the horizontal base excitation,the total velocity potential of fluid is decomposed of the impulsive and perturbed velocity potentials.The orthogonality of the sloshing modes is demonstrated by implementing Gauss formula.The dynamic response equation is established by incorporating the total velocity potential solution into the surface wave equation.Excellent agreements are achieved between the present results and those from the reported literature and finite element code.Numerical results are exhibited to reveal the effect of the baffle parameters and excitation frequency on sloshing characteristics and responses of liquid.
基金This work was supported by the National Natural Science Foundation of China.
文摘A series of liquid crystalline polymers with T-shaped two-dimensional mesogenic unitswere synthesized via low temperature solution polycondensation of 2-(4'-alkoxy-phenyl)hydroquinone with various diacyl dichlorides. The polymers were found to be nematic andshown thermotropic liquid crystalline behaviors through observations using DSC, polarizedmicroscopy and X-ray diffraction. The melting temperature T_m and the isotropizationtemperature T_i of the polymers change regularly with varying of the monomer structures.
基金This work was supported by the National Natural Science Foundation of China(No.29974026)the Natural Science Foundation of Henan Province(No.0211021100)the Education Department Foundation of Henan Province(No.20021500004).
文摘A novel series of liquid crystalline copolyesters with T-shaped two-dimensional mesogenic unit and crown ether cycle of cis-4,4′-bis(4-hydroxyphenylazo)dibenzo-18-crown-6 was prepared via solution condensation polymerization from 4,4′-(α,ω-hexanedioyloxy)dibenzoyl dichloride(M_1),2-(4′-ethoxyphenyl)hydroquinone(M_2)and cis-4,4′-bis(4- hydroxyphenylazo)dibenzo-18-crown-6(M_3).The molecular weights of copolyesters are not high,and the intrinsic viscosity [η]of copolyesters ranges from 0.29-0.43.The monomers ...
基金the Key Research and Development Program of Shaanxi Province,China(Grant No.2020ZDLGY03-05)the National Natural Science Foundation of China(Grant No.61574112).
文摘A novel vertical InN/InGaN heterojunction tunnel FET with hetero T-shaped gate as well as polarization-doped source and drain region(InN-Hetero-TG-TFET)is proposed and investigated by Silvaco-Atlas simulations for the first time.Compared with the conventional physical doping TFET devices,the proposed device can realize the P-type source and N-type drain region by means of the polarization effect near the top InN/InGaN and bottom InGaN/InN heterojunctions respectively,which could provide an effective solution of random dopant fluctuation(RDF)and the related problems about the high thermal budget and expensive annealing techniques due to ion-implantation physical doping.Besides,due to the hetero T-shaped gate,the improvement of the on-state performance can be achieved in the proposed device.The simulations of the device proposed here in this work show ION of 4.45×10^(-5)A/μm,ION/IOFF ratio of 10^(13),and SS_(avg)of 7.5 mV/dec in InN-Hetero-TG-TFET,which are better than the counterparts of the device with a homo T-shaped gate(InN-Homo-TG-TFET)and our reported lateral polarization-induced InN-based TFET(PI-InN-TFET).These results can provide useful reference for further developing the TFETs without physical doping process in low power electronics applications.
基金This work was supported by the National Natural Science Foundation of China.
文摘A new series of liquid crystal polyesters with T-shaped two-dimensional mesogenic units weresynthesized by melt polycondensation of the diacetates of 2-(4'-alkoxy -phenyl)-hydroquinones with 4,4'-alkylenedioxydibenzoic acid. The polymers were characterized by using polarized microscopy, DSC and X-ray diffraction. It was realized that all the polymers have nematic thermotropic liquid crystallinecharacteristics. The melting temperature (T_m) and isotropization temperature (T_i) of the polymers changeregularly with varying lengths of the alkoxy side group and the length of the alkylene group in the main chainin company with an even-odd effect. The mesophase temperature range also varies regularly with the polymerstructure. It is shown that the mesophase range has been widened.
文摘This paper proposes,demonstrates,and describes a basic T-shaped Multi-Input and Multi-Output(MIMO)antenna with a resonant frequency of 3.1 to 10.6 GHz.Compared with the U-shaped antenna,the mutual coupling is minimized by using a T-shaped patch antenna.The T-shaped patch antenna shapes filter properties are tested to achieve separation over the 3.1 to 10.6 GHz frequency range.The parametric analysis,including width,duration,and spacing,is designed in the MIMO applications for good isolation.On the FR4 substratum,the configuration of MIMO is simulated.The appropriate dielectric material ε_(r)=4.4 is introduced using this contribution and application array feature of the MIMO systems.In this paper,FR4 is used due to its high dielectric strength and low cost.For 3.1 to 10.6 GHz and 3SRR,T-shaped patch antennas are used in the field to increase bandwidth.The suggested Tshaped MIMO antenna is calculated according to the HFSS 13.0 program simulation performances.The antenna suggested is,therefore,a successful WLAN candidate.
文摘A compact CPW-fed double T-Shaped antenna is proposed for dual-band wireless local area network (WLAN) operations. For the proposed antenna, the -10 dB return loss bandwidth could reach about 25.5% for the 2.4 GHz band and 5.7 % for the 5 GHz band, which meet the required bandwidth specification of WLAN standard. To reduce the mutual coupling and get high isolation between two dual-band antennas, we proposed the novel electromagnetic band gap (EBG) structures. When the EBG structure is employed, a -13dB and -30dB mutual coupling reduction is achieved at 2.4 and 5.2 GHz. It shows that the features of small size, uniplanar structure, good radiation characteristics and small mutual coupling are promising for multi-input multi-output (MIMO) applications.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.61306116 and 61472322)
文摘A new T-shaped tunnel field-effect transistor(TTFET) with gate dielectric spacer(GDS) structure is proposed in this paper. To further studied the effects of GDS structure on the TTFET, detailed device characteristics such as current-voltage relationships, energy band diagrams, band-to-band tunneling(BTBT) rate and the magnitude of the electric field are investigated by using TCAD simulation. It is found that compared with conventional TTFET and TTFET with gate-drain overlap(GDO) structure, GDS-TTFET not only has the minimum ambipolar current but also can suppress the ambipolar current under a more extensive bias range. Furthermore, the analog/RF performances of GDS-TTFET are also investigated in terms of transconductance, gate-source capacitance, gate-drain capacitance, cutoff frequency, and gain bandwidth production. By inserting a low-κ spacer layer between the gate electrode and the gate dielectric, the GDS structure can effectively reduce parasitic capacitances between the gate and the source/drain, which leads to better performance in term of cutoff frequency and gain bandwidth production. Finally, the thickness of the gate dielectric spacer is optimized for better ambipolar current suppression and improved analog/RF performance.
基金supported by the National Key R&D Program of China(2017YFB0502700)the National Natural Science Foundation of China(61490693+3 种基金61771043)the High-Resolution Earth Observation Systems(41-Y20A14-9001-15/1630-Y20A12-9004-15/1630-Y20A10-9001-15/16)
文摘To automatically detect oil tanks in polarimetric synthetic aperture radar(SAR) images, a coastal oil tank detection method is proposed based on recognition of T-shaped harbor. First of all, the T-shaped harbor is detected to locate the region of interest(ROI) of oil tanks. Then all suspicious targets in the ROI are extracted by the segmentation of strong scattering targets and the classifier of H/α. The template targets are selected from the suspicious targets by the combination of a proposed circular degree parameter and the similarity parameter(SP) of the polarimetric coherency matrix. Finally, oil tanks are detected according to the statistics of the similarity parameter between each suspicious target and template targets in ROI. Polarimetric SAR data acquired by RADARSAT-2 over Berkeley and Singapore areas are used for testing. Experiment results show that most of the targets are correctly detected and the overall detection rate is close to 80%.The false rate is effectively reduced by the proposed algorithm compared with the method without T-shaped harbor recognition.
基金Fundamental Research Funds for the Central Universities,China(No.2011D10543,No.2013D110525)
文摘Traditional preparation of magnetic microcapsules involves cumbersome processes and often results in irregular-shaped products. Due to the stable laminar flow of reaction solution and the moderate reaction conditions, the T-shaped microchannel (T-MC) reactor is supposed to yield microcapsules with regular shape. In this paper, magnetic particles of ferroferric oxide modified by oleic acid (OA-Fe3O4) and dispersed in tetrachloroethylene were used as core material. Polymethyl methacrylate (PMMA) was used as shell material. Magnetic microcapsules were prepared by using a T-MC reactor. Factors that influenced the encapsulated reaction were investigated in details, which included the velocity ratio of aqueous phase to oil phase, the length and the inner diameter of the microchannel. The morphology, composition, and magnetic responsiveness of the magnetic microcapsules were analyzed and characterized by SEM, FTIR, XRD, TGA, and vibrating sample magnetometer (VSM). The results confirmed that magnetic microcapsules prepared by T-MC reactor were regular in shape.
基金Tins work was supported by the National Natural Science Foundation of China.
文摘Two series of new liquid crystalline polymers with T-shaped two-dimensional mesogenic units were synthesized by low temperature solution polycondensations of 4-substituted N-2, 5-dihydroxybenzylidene aniline monomers with different diacyl dichlorides. The polymers were found to be nematic and shown liquid crystalline behavior. The melting temperature T-m and the clearing temperature T-i of the polymers change regularly with varying of the monomer structures.
基金Project supported by the National Key Basic Research Program of China (Grant No. 2013CB328702)
文摘By utilizing a Fabry–Perot (FP) nanocavity adjacent to T-shaped gap waveguide ports, spectrally selective filtering is realized. When the wavelength of incident light corresponds to the resonance wavelength of the FP nanocavity, the surface plasmons are captured inside the nanocavity, and light is highly reflected from this port. The resonance wavelength is determined by using Fabry–Perot resonance condition for the nanocavity. For any desired filtering frequency the dimension of the nanocavity can be tailored. The numerical results are based on the two-dimensional finite difference time domain simulation under a perfectly matched layer absorbing boundary condition. The analytical and simulation results indicate that the proposed structure can be utilized for filtering and splitting applications.
基金supported by National Nature Science Foundation of China(51507031).
文摘In order to effectively solve the dead-zone and low-precision of T-shaped transmission line fault location,a new T-shaped transmission line fault location algorithm based on phase-angle jump checking is proposed in this paper.Firstly,the 3-terminal synchronous fundamental positive sequence voltage and current phasors are extracted and substituted into the fault branch distance function to realize the selection of fault branch when the fault occurs;Secondly,use the condition of the fundamental positive sequence voltage phasor at the fault point is equal to calculate all roots(including real root and virtual roots);Finally,the phase-angle jump check function is used for checking calculation,and then the only real root can be determined as the actual fault distance,thereby achieving the purpose of high-precision fault location.MATLAB simulation results show that the proposed new algorithm is feasible and effective with high fault location accuracy and good versatility.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.61574112,61334002,61306017,61474091,and 61574110)the Natural Science Basic Research Plan in Shaanxi Province,China(Grant No.605119425012)
文摘A novel A1GaN/GaN high electron mobility transistor (HEMT) with a source-connected T-shaped field-plate (ST-FP HEMT) is proposed for the first time in this paper. The source-connected T-shaped field-plate (ST-FP) is composed of a source-connected field-plate (S-FP) and a trench metal. The physical intrinsic mechanisms of the ST-FP to improve the breakdown voltage and the FP efficiency and to modulate the distributions of channel electric field and potential are studied in detail by means of two-dimensional numerical simulations with Silvaco-ATLAS. A comparison to the HEMT and the HEMT with an S-FP (S-FP HEMT) shows that the ST-FP HEMT could achieve a broader and more uniform channel electric field distribution with the help of a trench metal, which could increase the breakdown voltage and the FP efficiency remarkably. In addition, the relationship between the structure of the ST-FP, the channel electric field, the breakdown voltage as well as the FP efficiency in ST-FP HEMT is analyzed. These results could open up a new effective method to fabricate high voltage power devices for the power electronic applications.
基金supported by the National Natural Science Foundation of China(21978197 and 21776200)。
文摘The bubble formation dynamics and size manipulation in the slurry of polystyrene microspheres in the microfluidic T-junction were visually investigated by a high-speed camera.Based on the evolution of the bubble neck with time,the formation process of bubbles is divided into three stages:filling,squeezing and pinch-off.The particle concentration has an obvious effect on the squeezing stage,while less impact on the filling and pinch-off stages.In the squeezing stage,the evolution of the dimensionless minimum neck width of bubbles with time could be described by a power-law relationship.The increase of the particle concentration or continuous phase flow rate could lead to the increase of body flow of the continuous phase and the enhancement of the squeezing force acted on the bubble neck,correspondingly,the power-law index a in the squeezing stage enlarges.Moreover,the bubble size increases with the increase of the gas phase flow rate and the decrease of the particle concentration and continuous phase flow rate.However,the effect of the particle concentration on the bubble size weakens with the increase of the continuous phase flow rate.In addition,a new prediction correlation of the bubble size for the slurry system in a T-shape microchannel was proposed with good prediction accuracy.
基金the National Natural Science Foundation of China under Grant 61822407,Grant 61527816,Grant 11634002,Grant 61631021,Grant 62074161,Grant 62004213,and Grant U20A20208in part by the Key Research Program of Frontier Sciences,Chinese Academy of Sciences(CAS)under Grant QYZDB-SSW-JSC012+2 种基金in part by the Youth Innovation Promotion Association of CASin part by the University of CASthe Opening Project of Key Laboratory of Microelectronic Devices&Integrated Technology,Institute of Microelectronics,CAS.
文摘Parasitic capacitances associated with overhangs of the T-shape-gate enhancement-mode(E-mode)GaN-based power device,were investigated by frequency/voltage-dependent capacitance-voltage and inductive-load switching measurements.The overhang capacitances induce a pinch-off voltage distinguished from that of the E-mode channel capacitance in the gate capacitance and the gatedrain capacitance characteristic curves.Frequency-and voltage-dependent tests confirm the instability caused by the trapping of interface/bulk states in the LPCVD-SiNx passivation dielectric.Circuit-level double pulse measurement also reveals its impact on switching transition for power switching applications.