The blade root fatigue is one of important failure modes of turbocharger turbine for vehicle application,and the reliability and life of turbine with blade root fatigue failure mode are studied.Firstly,the stress char...The blade root fatigue is one of important failure modes of turbocharger turbine for vehicle application,and the reliability and life of turbine with blade root fatigue failure mode are studied.Firstly,the stress characteristics of turbine are analyzed,and based on the operating profile of turbocharger corresponding to the endurance test of engine,the stress spectrum of turbine with blade root fatigue failure mode is studied with the simulation method.Then,with the number of endurance test profile cycle as the life parameter,the reliability model and failure rate model of turbine with blade root fatigue failure mode are derived respectively. Finally,the rules that the reliability and failure rate of turbine with the blade root fatigue failure mode changes as life parameters are studied,and the life probabilistic characteristics of turbine are also studied.展开更多
In order to effectively solve the dead-zone and low-precision of T-shaped transmission line fault location,a new T-shaped transmission line fault location algorithm based on phase-angle jump checking is proposed in th...In order to effectively solve the dead-zone and low-precision of T-shaped transmission line fault location,a new T-shaped transmission line fault location algorithm based on phase-angle jump checking is proposed in this paper.Firstly,the 3-terminal synchronous fundamental positive sequence voltage and current phasors are extracted and substituted into the fault branch distance function to realize the selection of fault branch when the fault occurs;Secondly,use the condition of the fundamental positive sequence voltage phasor at the fault point is equal to calculate all roots(including real root and virtual roots);Finally,the phase-angle jump check function is used for checking calculation,and then the only real root can be determined as the actual fault distance,thereby achieving the purpose of high-precision fault location.MATLAB simulation results show that the proposed new algorithm is feasible and effective with high fault location accuracy and good versatility.展开更多
Removal of milling marks at the root fillet of titanium alloy blade is a tough work because of the interference between the polishing tool and the workpiece.A polishing method based on elastic magnetic tool was propos...Removal of milling marks at the root fillet of titanium alloy blade is a tough work because of the interference between the polishing tool and the workpiece.A polishing method based on elastic magnetic tool was proposed.The software ANSYS Maxwell was used to simulate the effect of different pole orientation arrangements on the magnetic field distribution.A comparison of polishing effect was made between elastic and inelastic magnetic pole carriers.The processing parameters of the elastic magnetic tool polishing for the blade root were optimized by orthogonal experiment(Taguchi)method.Results show that compared with the inelastic magnetic polishing tool,the elastic magnetic polishing tool with polyurethane as the pole carrier can effectively improve the surface quality of the polished workpiece.Under the optimal processing parameters(rotational speed=900 r/min,feeding rate=6 mm/min,machining gap=1.5 mm and abrasive size=10‒14μm),the original milling marks at the blade root are effectively removed and the average surface roughness Ra is dropped from 0.95μm to 0.12μm,which verifies the feasibility of the elastic magnetic polishing tool in the surface finishing of the titanium alloy blade root.展开更多
基金National Natural Science Foundation of China(No.51375465)
文摘The blade root fatigue is one of important failure modes of turbocharger turbine for vehicle application,and the reliability and life of turbine with blade root fatigue failure mode are studied.Firstly,the stress characteristics of turbine are analyzed,and based on the operating profile of turbocharger corresponding to the endurance test of engine,the stress spectrum of turbine with blade root fatigue failure mode is studied with the simulation method.Then,with the number of endurance test profile cycle as the life parameter,the reliability model and failure rate model of turbine with blade root fatigue failure mode are derived respectively. Finally,the rules that the reliability and failure rate of turbine with the blade root fatigue failure mode changes as life parameters are studied,and the life probabilistic characteristics of turbine are also studied.
基金supported by National Nature Science Foundation of China(51507031).
文摘In order to effectively solve the dead-zone and low-precision of T-shaped transmission line fault location,a new T-shaped transmission line fault location algorithm based on phase-angle jump checking is proposed in this paper.Firstly,the 3-terminal synchronous fundamental positive sequence voltage and current phasors are extracted and substituted into the fault branch distance function to realize the selection of fault branch when the fault occurs;Secondly,use the condition of the fundamental positive sequence voltage phasor at the fault point is equal to calculate all roots(including real root and virtual roots);Finally,the phase-angle jump check function is used for checking calculation,and then the only real root can be determined as the actual fault distance,thereby achieving the purpose of high-precision fault location.MATLAB simulation results show that the proposed new algorithm is feasible and effective with high fault location accuracy and good versatility.
基金Joint Funds of the National Natural Science Foundation of China(U20A20293)。
文摘Removal of milling marks at the root fillet of titanium alloy blade is a tough work because of the interference between the polishing tool and the workpiece.A polishing method based on elastic magnetic tool was proposed.The software ANSYS Maxwell was used to simulate the effect of different pole orientation arrangements on the magnetic field distribution.A comparison of polishing effect was made between elastic and inelastic magnetic pole carriers.The processing parameters of the elastic magnetic tool polishing for the blade root were optimized by orthogonal experiment(Taguchi)method.Results show that compared with the inelastic magnetic polishing tool,the elastic magnetic polishing tool with polyurethane as the pole carrier can effectively improve the surface quality of the polished workpiece.Under the optimal processing parameters(rotational speed=900 r/min,feeding rate=6 mm/min,machining gap=1.5 mm and abrasive size=10‒14μm),the original milling marks at the blade root are effectively removed and the average surface roughness Ra is dropped from 0.95μm to 0.12μm,which verifies the feasibility of the elastic magnetic polishing tool in the surface finishing of the titanium alloy blade root.
