Dynamic behavior of outburst two-phase flow in a coal mine T-shaped roadway:The formation of impact airflow and its disaster-causing effect

The study of the dynamic disaster mechanism of coal and gas outburst two-phase flow is crucial for improving disaster reduction and rescue ability of coal mine outburst accidents.An outburst test in a T-shaped roadway was conducted using a self-developed large-scale outburst dynamic disaster test system.We investigated the release characteristics of main energy sources in coal seam,and obtained the dynamic characteristics of outburst two-phase flow in a roadway.Additionally,we established a formation model for outburst impact flow and a model for its flow in a bifurcated structure.The results indicate that the outburst process exhibits pulse characteristics,and the rapid destruction process of coal seam and the blocking state of gas flow are the main causes of the pulse phenomenon.The outburst energy is released in stages,and the elastic potential energy is released in the vertical direction before the horizontal direction.In a straight roadway,the impact force oscillates along the roadway.With an increase in the solid–gas ratio,the two-phase flow impact force gradually increases,and the disaster range extends from the middle of the roadway to the coal seam.In the area near the coal seam,the disaster caused by the two-phase flow impact is characterized by intermittent recovery.In a bifurcated roadway,the effect of impact airflow on impact dynamic disaster is much higher than that of two-phase flow,and the impact force tends to weaken with increasing solid-gas ratio.The impact force is asymmetrically distributed;it is higher on the left of the bifurcated roadway.With an increase in the solid-gas ratio,the static pressure rapidly decreases,and the bifurcated structure accelerates the attenuation of static pressure.Moreover,secondary acceleration is observed when the shock wave moves along the T-shaped roadway,indicating that the bifurcated structure increases the shock wave velocity.

Flow Regimes in Bubble Columns with and without Internals: A Review

Hydrodynamics characterization in terms offlow regime behavior is a crucial task to enhance the design of bubble column reactors and scaling up related methodologies.This review presents recent studies on the typicalflow regimes established in bubble columns.Some effort is also provided to introduce relevant definitions pertaining to thisfield,namely,that of“void fraction”and related(local,chordal,cross-sectional and volumetric)variants.Experimental studies involving different parameters that affect design and operating conditions are also discussed in detail.In the second part of the review,the attention is shifted to cases with internals of various types(perfo-rated plates,baffles,vibrating helical springs,mixers,and heat exchanger tubes)immersed in the bubble columns.It is shown that the presence of these elements has a limited influence on the global column hydrodynamics.However,they can make the homogeneousflow regime more stable in terms of transition gas velocity and transi-tion holdup value.The last section is used to highlight gaps which have not beenfilled yet and future directions of investigation.

Visual experimental study of nanofluids application to promote CO_(2) absorption in a bubble column

The addition of dispersed-phase nanoparticles in the liquid phase can enhance the gas-liquid transfer process as the suspended nanoparticles affect the transfer process inside the fluid through microdisturbance or micro-convection effects.In this article,a high-speed digital camera was used to visualize the bubble behavior of CO_(2) in pure water and nanofluids to examine the effects of CO_(2) gas flow rate,nanoparticle solid content and type on the bubble behavior in the fluids.The CO_(2) absorption performance in three water-based nanofluids were compared in a bubbler.And the mass transfer characteristics during CO_(2) bubble absorption and the reasons for the enhanced gas-liquid mass transfer effect of nanoparticles were analyzed.The results showed that the presence of nanoparticles affected the formation process of bubbles in the fluid,shortened the bubble detachment time,reduced the detachment diameter,effectively increased the gas-liquid contact area,and improved the bubbles detachment frequency.The system with MCM-41 corresponded to a higher overall mass transfer coefficient.Uncalined MCM-41 contained surfactant that enhanced foaming behavior in water.This prevented the transfer of CO_(2) to some extent,and the CO_(2) absorption by uncalined MCM-41/H_(2)O was 5.34%higher than that by pure water.Compared with SiO_(2) nanoparticles with the same particle size and the same composition,MCM-41 had a higher adsorption capacity and better hydrophilicity due to its larger specific surface area and rich porous structure,which was more favorable to accelerate the collision between nanoparticles and CO_(2) bubbles to cause micro-convection.Under the condition of 0.1%(mass)solid content,the enhancement of CO_(2) absorption process by MCM-41 nanoparticles was more significant and improved by 16.9%compared with pure water.

Numerical Analysis of Cold-Formed Thin-Walled Steel Short Columns with Pitting Corrosion during Bridge Construction

Pitting corrosion is harmful during bridge construction,which will lead to uneven roughness of steel surfaces and reduce the thickness of steel.Hence,the effect of pitting corrosion on the mechanical properties of cold-formed thin-walled steel stub columns is studied,and the empirical formulas are established through regression fitting to predict the ultimate load of web and flange under pitting corrosion.In detail,the failure modes and load-displacement curves of specimens with different locations,area ratios,and depths are obtained through a large number of non-linear finite element analysis.As for the specimens with pitting corrosion on the web,all the specimens are subject to local buckling failure,and the failure mode will not change with pitting corrosion,but the failure location will change with pitting corrosion location;the size,location,and area ratio of pitting corrosion have little influence on the ultimate load of cold-formed thin-walled steel short columns,but the loss rate of pitting corrosion section area has a greater impact on the ultimate bearing capacity.As for the specimen with flange pitting corrosion,the location and area ratio of pitting corrosion have less influence on the ultimate load of cold-formed thin-walled steel short columns,and the section area loss rate has greater influence on the ultimate bearing capacity;the impact of web pitting corrosion on the ultimate load is greater than that of flange pitting corrosion under the same condition of pitting corrosion section area.The prediction formulas of limit load which are suitable for pitting corrosion of web and flange are established,which can provide a reference for performance evaluation of corroded cold-formed thin-walled steel.

An Affordable and Easily Accessible Approach for Acrylonitrile Monomer Purification through a Simple Column Technique

This manuscript presents a dataset detailing a method for purifying monomers. Purification plays a crucial role in every chemical process, as it leads to an improvement in product quality through the removal of impurities. The primary method for monomer purification, like acrylonitrile (AN), is the distillation technique. However, this technique is unsafe and hard to set up or handle. A straightforward, risk-free, low-cost method like the column technique resolves these issues. A simple column technique demonstrated the successful execution of purifying AN. Fourier transform infrared (FTIR) and nuclear magnetic resonance (NMR) analyses confirmed that AN was successfully purified, with purity reaching 99.8%. FTIR spectra revealed changes in the position and intensity of the stretching vibration peaks after purification. Also, the functional groups of the inhibitor monomethyl ether of hydroquinone (MeHQ) were undetected after purification. Furthermore, after purification, NMR spectra revealed the absence of aromatic protons and carbons associated with MeHQ. In conclusion, the column technique is a successful and inexpensive way to purify AN monomers. This makes it useful for a wide range of applications, especially in polymerization reactions where MeHQ needs to be removed to prevent self-polymerization during the initiation process.

Improved design of special boundary elements for T-shaped reinforced concrete walls

This study examines the design provisions of the Chinese GB 50011-2010 code for seismic design of buildings for the special boundary elements of T-shaped reinforced concrete walls and proposes an improved design method. Comparison of the design provisions of the GB 50011-2010 code and those of the American code ACI 318-14 indicates a possible deficiency in the T-shaped wall design provisions in GB 50011-2010. A case study of a typical T-shaped wall designed in accordance with GB 50011-2010 also indicates the insufficient extent of the boundary element at the non-flange end and overly conservative design of the flange end boundary element. Improved designs for special boundary elements ofT-shaped walls are developed using a displacement-based method. The proposed design formulas produce a longer boundary element at the non-flange end and a shorter boundary element at the flange end, relative to those of the GB 50011-2010 provisions. Extensive numerical analysis indicates that T-shaped walls designed using the proposed formulas develop inelastic drift of 0.01 for both cases of the flange in compression and in tension.

Static and dynamic responses of a microcantilever with a T-shaped tip mass to an electrostatic actuation

In this study, nonlinear static and dynamic responses of a microcantilever with a T-shaped tip mass excited by electrostatic actuations are investigated. The electrostatic force is generated by applying an electric voltage between the horizontal part of?T-shaped tip mass and an opposite electrode plate. The cantilever microbeam is modeled as an Euler-Bernoulli beam. The T-shaped tip mass is assumed to be a rigid body and the nonlinear effect of electrostatic force is considered. An equation of motion and its associated boundary conditions are derived by the aid of combining the Hamilton principle and Newton’s method. An exact solution is obtained for static deflection and mode shape of vibration around the static position. The differential equation of nonlinear vibration around the static position is discretized using the Galerkin method. The system mode shapes are used as its related comparison functions. The discretized equations are solved by the perturbation theory in the neighborhood of primary and subharmonic resonances. In addition, effects of mass inertia, mass moment of inertia as well as rotation of the T-shaped mass, which were ignored in previous works, are considered in the analysis. It is shown that by increasing the length of the horizontal part of the T-shaped mass, the amount of static deflection increases, natural frequency decreases and nonlinear shift of the resonance frequency increases. It is concluded that attaching an electrode plate with a T-shaped configuration to the end of the cantilever microbeam results in a configuration with larger pull-in voltage and smaller nonlinear shift of the resonance frequency compared to the configuration in which the electrode plate is directly attached to it.

Analytical Modeling of Fluid Sloshing in A 2D Rectangular Container with A Bottom-Mounted T-Shaped Baffle

An analytical procedure is presented to evaluate the fluid sloshing characteristics in a two-dimensional(2D)rectangular container with a bottom-mounted T-shaped baffle.The fluid region is divided into several sub-domains with hypothetical interfaces and the velocities and pressures of the fluid on adjacent interfaces should be identical.The separation of variables in conjunction with the superposition principle is employed to formulate the velocity potential of each sub-domain.The Fourier series expansion is used to derive the eigenvalue equation by substituting the velocity potential solutions into the free surface conditions and the continuity conditions on adjacent interfaces.Under the horizontal base excitation,the total velocity potential of fluid is decomposed of the impulsive and perturbed velocity potentials.The orthogonality of the sloshing modes is demonstrated by implementing Gauss formula.The dynamic response equation is established by incorporating the total velocity potential solution into the surface wave equation.Excellent agreements are achieved between the present results and those from the reported literature and finite element code.Numerical results are exhibited to reveal the effect of the baffle parameters and excitation frequency on sloshing characteristics and responses of liquid.

Stresses due to an adhesion crack in T-shaped junction of two orthotropic plates

The general solution of stresses is derived for a T-shaped junction of two thin plates with an adhesion crack. The plates are orthotropic. A shear force is applied on the crack surface. The analysis is based on the supposition that the stresses in each plate can be approximated by a plane stress condition. The results obtained are verified by numerical calculation of FEM.

SYNTHESIS AND CHARACTERIZATION OF LIQUID CRYSTAL POLYMERS WITH T-SHAPED TWO-DIMENSIONAL MESOGENIC UNITS (Ⅱ)

A series of liquid crystalline polymers with T-shaped two-dimensional mesogenic unitswere synthesized via low temperature solution polycondensation of 2-(4'-alkoxy-phenyl)hydroquinone with various diacyl dichlorides. The polymers were found to be nematic andshown thermotropic liquid crystalline behaviors through observations using DSC, polarizedmicroscopy and X-ray diffraction. The melting temperature T_m and the isotropizationtemperature T_i of the polymers change regularly with varying of the monomer structures.

SYNTHESIS OF LIQUID CRYSTALLINE COPOLYESTERS WITH T-SHAPED TWO-DIMENSIONAL MESOGENIC UNIT AND CROWN ETHER CYCLE

A novel series of liquid crystalline copolyesters with T-shaped two-dimensional mesogenic unit and crown ether cycle of cis-4,4′-bis(4-hydroxyphenylazo)dibenzo-18-crown-6 was prepared via solution condensation polymerization from 4,4′-(α,ω-hexanedioyloxy)dibenzoyl dichloride(M_1),2-(4′-ethoxyphenyl)hydroquinone(M_2)and cis-4,4′-bis(4- hydroxyphenylazo)dibenzo-18-crown-6(M_3).The molecular weights of copolyesters are not high,and the intrinsic viscosity [η]of copolyesters ranges from 0.29-0.43.The monomers ...

Vertical polarization-induced doping InN/InGaN heterojunction tunnel FET with hetero T-shaped gate

A novel vertical InN/InGaN heterojunction tunnel FET with hetero T-shaped gate as well as polarization-doped source and drain region(InN-Hetero-TG-TFET)is proposed and investigated by Silvaco-Atlas simulations for the first time.Compared with the conventional physical doping TFET devices,the proposed device can realize the P-type source and N-type drain region by means of the polarization effect near the top InN/InGaN and bottom InGaN/InN heterojunctions respectively,which could provide an effective solution of random dopant fluctuation(RDF)and the related problems about the high thermal budget and expensive annealing techniques due to ion-implantation physical doping.Besides,due to the hetero T-shaped gate,the improvement of the on-state performance can be achieved in the proposed device.The simulations of the device proposed here in this work show ION of 4.45×10^(-5)A/μm,ION/IOFF ratio of 10^(13),and SS_(avg)of 7.5 mV/dec in InN-Hetero-TG-TFET,which are better than the counterparts of the device with a homo T-shaped gate(InN-Homo-TG-TFET)and our reported lateral polarization-induced InN-based TFET(PI-InN-TFET).These results can provide useful reference for further developing the TFETs without physical doping process in low power electronics applications.

SYNTHESIS AND CHARACTERIZATION OF LIQUID CRYSTAL POLYESTERS WITH T-SHAPED TWO-DIMENSIONAL MESOGENIC UNITS(Ⅲ)

A new series of liquid crystal polyesters with T-shaped two-dimensional mesogenic units weresynthesized by melt polycondensation of the diacetates of 2-(4'-alkoxy -phenyl)-hydroquinones with 4,4'-alkylenedioxydibenzoic acid. The polymers were characterized by using polarized microscopy, DSC and X-ray diffraction. It was realized that all the polymers have nematic thermotropic liquid crystallinecharacteristics. The melting temperature (T_m) and isotropization temperature (T_i) of the polymers changeregularly with varying lengths of the alkoxy side group and the length of the alkylene group in the main chainin company with an even-odd effect. The mesophase temperature range also varies regularly with the polymerstructure. It is shown that the mesophase range has been widened.

Prediction of column failure modes based on artificial neural network

To implement the performance-based seismic design of engineered structures,the failure modes of members must be classified.The classification method of column failure modes is analyzed using data from the Pacific Earthquake Engineering Research Center(PEER).The main factors affecting failure modes of columns include the hoop ratios,longitudinal reinforcement ratios,ratios of transverse reinforcement spacing to section depth,aspect ratios,axial compression ratios,and flexure-shear ratios.This study proposes a data-driven prediction model based on an artificial neural network(ANN)to identify the column failure modes.In this study,111 groups of data are used,out of which 89 are used as training data and 22 are used as test data,and the ANN prediction model of failure modes is developed.The results show that the proposed method based on ANN is superior to traditional methods in identifying the column failure modes.

Design and Implementation of T-Shaped Planar Antenna for MIMO Applications

This paper proposes,demonstrates,and describes a basic T-shaped Multi-Input and Multi-Output(MIMO)antenna with a resonant frequency of 3.1 to 10.6 GHz.Compared with the U-shaped antenna,the mutual coupling is minimized by using a T-shaped patch antenna.The T-shaped patch antenna shapes filter properties are tested to achieve separation over the 3.1 to 10.6 GHz frequency range.The parametric analysis,including width,duration,and spacing,is designed in the MIMO applications for good isolation.On the FR4 substratum,the configuration of MIMO is simulated.The appropriate dielectric material ε_(r)=4.4 is introduced using this contribution and application array feature of the MIMO systems.In this paper,FR4 is used due to its high dielectric strength and low cost.For 3.1 to 10.6 GHz and 3SRR,T-shaped patch antennas are used in the field to increase bandwidth.The suggested Tshaped MIMO antenna is calculated according to the HFSS 13.0 program simulation performances.The antenna suggested is,therefore,a successful WLAN candidate.

CPW Fed Double T-Shaped Array Antenna with Suppressed Mutual Coupling

A compact CPW-fed double T-Shaped antenna is proposed for dual-band wireless local area network (WLAN) operations. For the proposed antenna, the -10 dB return loss bandwidth could reach about 25.5% for the 2.4 GHz band and 5.7 % for the 5 GHz band, which meet the required bandwidth specification of WLAN standard. To reduce the mutual coupling and get high isolation between two dual-band antennas, we proposed the novel electromagnetic band gap (EBG) structures. When the EBG structure is employed, a -13dB and -30dB mutual coupling reduction is achieved at 2.4 and 5.2 GHz. It shows that the features of small size, uniplanar structure, good radiation characteristics and small mutual coupling are promising for multi-input multi-output (MIMO) applications.

Optimization of ambipolar current and analog/RF performance for T-shaped tunnel field-effect transistor with gate dielectric spacer

A new T-shaped tunnel field-effect transistor(TTFET) with gate dielectric spacer(GDS) structure is proposed in this paper. To further studied the effects of GDS structure on the TTFET, detailed device characteristics such as current-voltage relationships, energy band diagrams, band-to-band tunneling(BTBT) rate and the magnitude of the electric field are investigated by using TCAD simulation. It is found that compared with conventional TTFET and TTFET with gate-drain overlap(GDO) structure, GDS-TTFET not only has the minimum ambipolar current but also can suppress the ambipolar current under a more extensive bias range. Furthermore, the analog/RF performances of GDS-TTFET are also investigated in terms of transconductance, gate-source capacitance, gate-drain capacitance, cutoff frequency, and gain bandwidth production. By inserting a low-κ spacer layer between the gate electrode and the gate dielectric, the GDS structure can effectively reduce parasitic capacitances between the gate and the source/drain, which leads to better performance in term of cutoff frequency and gain bandwidth production. Finally, the thickness of the gate dielectric spacer is optimized for better ambipolar current suppression and improved analog/RF performance.

A method for coastal oil tank detection in polarimetric SAR images based on recognition of T-shaped harbor

To automatically detect oil tanks in polarimetric synthetic aperture radar（SAR） images, a coastal oil tank detection method is proposed based on recognition of T-shaped harbor. First of all, the T-shaped harbor is detected to locate the region of interest（ROI） of oil tanks. Then all suspicious targets in the ROI are extracted by the segmentation of strong scattering targets and the classifier of H/α. The template targets are selected from the suspicious targets by the combination of a proposed circular degree parameter and the similarity parameter（SP） of the polarimetric coherency matrix. Finally, oil tanks are detected according to the statistics of the similarity parameter between each suspicious target and template targets in ROI. Polarimetric SAR data acquired by RADARSAT-2 over Berkeley and Singapore areas are used for testing. Experiment results show that most of the targets are correctly detected and the overall detection rate is close to 80%.The false rate is effectively reduced by the proposed algorithm compared with the method without T-shaped harbor recognition.

Novel Preparation of Magnetic Microcapsules by Using T-Shaped Microchannel Reactor

Traditional preparation of magnetic microcapsules involves cumbersome processes and often results in irregular-shaped products. Due to the stable laminar flow of reaction solution and the moderate reaction conditions, the T-shaped microchannel (T-MC) reactor is supposed to yield microcapsules with regular shape. In this paper, magnetic particles of ferroferric oxide modified by oleic acid (OA-Fe3O4) and dispersed in tetrachloroethylene were used as core material. Polymethyl methacrylate (PMMA) was used as shell material. Magnetic microcapsules were prepared by using a T-MC reactor. Factors that influenced the encapsulated reaction were investigated in details, which included the velocity ratio of aqueous phase to oil phase, the length and the inner diameter of the microchannel. The morphology, composition, and magnetic responsiveness of the magnetic microcapsules were analyzed and characterized by SEM, FTIR, XRD, TGA, and vibrating sample magnetometer (VSM). The results confirmed that magnetic microcapsules prepared by T-MC reactor were regular in shape.

SYNTHESIS AND CHARACTERIZATION OF LIQUID CRYSTAL POLYMERS WITH T-SHAPED TWO-DIMENSIONAL MESOGENIC UNITS

Two series of new liquid crystalline polymers with T-shaped two-dimensional mesogenic units were synthesized by low temperature solution polycondensations of 4-substituted N-2, 5-dihydroxybenzylidene aniline monomers with different diacyl dichlorides. The polymers were found to be nematic and shown liquid crystalline behavior. The melting temperature T-m and the clearing temperature T-i of the polymers change regularly with varying of the monomer structures.