Influences of fillet radius and draft angle on local loading process of titanium alloy T-shaped components

In order to study influences of geometric parameters on the T-shaped components local loading process, a new mathematical model considering the fillet radius and draft angle was established by using the slab method. The results obtained by the mathematical model agree with the data form experiment and numerical simulation, and the results are closer to the experimental and simulation results. The influence of draft angle may be neglected under the forming conditions used. The influence of fillet radius is notable, especially in the case that the ratio of fillet radius to rib width is less than 0.75.

Performance of a Self-Aligned InP/GaInAs SHBT with a Novel T-Shaped Emitter

A self-aligned InP/GalnAs single heterojunction bipolar transistor（HBT） is investigated using a novel T-shaped emitter. A U-shaped emitter layout,selective wet etching,laterally etched undercut, and an air-bridge are applied in this process. The device, which has a 2μm×12μm U-shaped emitter area,demonstrates a common-emitter DC current gain of 170,an offset voltage of 0.2V,a knee voltage of 0.5V, and an open-base breakdown voltage of over 2V. The HBT exhibits good microwave performance with a current gain cutoff frequency of 85GHz and a maximum oscillation frequency of 72GHz, These results indicate that these InP/InGaAs SHBTs are suitable for low-voltage,low-power,and high-frequency applications.

Improved design of special boundary elements for T-shaped reinforced concrete walls

This study examines the design provisions of the Chinese GB 50011-2010 code for seismic design of buildings for the special boundary elements of T-shaped reinforced concrete walls and proposes an improved design method. Comparison of the design provisions of the GB 50011-2010 code and those of the American code ACI 318-14 indicates a possible deficiency in the T-shaped wall design provisions in GB 50011-2010. A case study of a typical T-shaped wall designed in accordance with GB 50011-2010 also indicates the insufficient extent of the boundary element at the non-flange end and overly conservative design of the flange end boundary element. Improved designs for special boundary elements ofT-shaped walls are developed using a displacement-based method. The proposed design formulas produce a longer boundary element at the non-flange end and a shorter boundary element at the flange end, relative to those of the GB 50011-2010 provisions. Extensive numerical analysis indicates that T-shaped walls designed using the proposed formulas develop inelastic drift of 0.01 for both cases of the flange in compression and in tension.

Numerical investigation of flow pattern and components of three-dimensional velocity around a submerged T-shaped spur dike in a 90° bend

Spur dike is one of the river training structures. This work presented a numerical simulation of flow field and three-dimensional velocity around a T-shaped spur dike located in bend using SSIIM model. The main objective of this work is to investigate the three-dimensional velocities and streamlines at transverse and longitudinal sections and plan views around the T-shaped spur dike in different submergence ratios(0, 5%, 15%, 25% and 50%). It is concluded that by increasing the submergence ratio from 5% to 50%, the maximum of scour is reduced; the maximum of longitudinal velocity increases by 7.7% and occurs at the water surface in spur dike axis. Near the bed, the maximum of vertical velocity occurs at the end of spur wing. By analyzing the streamlines at transverse sections, the followings were deduced for different submergence ratios: different dimensions and different positions of vortices around the spur dike.

Analytical Modeling of Fluid Sloshing in A 2D Rectangular Container with A Bottom-Mounted T-Shaped Baffle

An analytical procedure is presented to evaluate the fluid sloshing characteristics in a two-dimensional(2D)rectangular container with a bottom-mounted T-shaped baffle.The fluid region is divided into several sub-domains with hypothetical interfaces and the velocities and pressures of the fluid on adjacent interfaces should be identical.The separation of variables in conjunction with the superposition principle is employed to formulate the velocity potential of each sub-domain.The Fourier series expansion is used to derive the eigenvalue equation by substituting the velocity potential solutions into the free surface conditions and the continuity conditions on adjacent interfaces.Under the horizontal base excitation,the total velocity potential of fluid is decomposed of the impulsive and perturbed velocity potentials.The orthogonality of the sloshing modes is demonstrated by implementing Gauss formula.The dynamic response equation is established by incorporating the total velocity potential solution into the surface wave equation.Excellent agreements are achieved between the present results and those from the reported literature and finite element code.Numerical results are exhibited to reveal the effect of the baffle parameters and excitation frequency on sloshing characteristics and responses of liquid.

Static and dynamic responses of a microcantilever with a T-shaped tip mass to an electrostatic actuation

In this study, nonlinear static and dynamic responses of a microcantilever with a T-shaped tip mass excited by electrostatic actuations are investigated. The electrostatic force is generated by applying an electric voltage between the horizontal part of T-shaped tip mass and an opposite electrode plate. The cantilever microbeam is modeled as an Euler-Bernoulli beam. The T-shaped tip mass is assumed to be a rigid body and the nonlinear effect of electrostatic force is considered. An equation of motion and its associated boundary conditions are derived by the aid of combining the Hamilton principle and Newton’s method. An exact solution is obtained for static deflection and mode shape of vibration around the static position. The differential equation of nonlinear vibration around the static position is discretized using the Galerkin method. The system mode shapes are used as its related comparison functions. The discretized equations are solved by the perturbation theory in the neighborhood of primary and subharmonic resonances. In addition, effects of mass inertia, mass moment of inertia as well as rotation of the T-shaped mass, which were ignored in previous works, are considered in the analysis. It is shown that by increasing the length of the horizontal part of the T-shaped mass, the amount of static deflection increases, natural frequency decreases and nonlinear shift of the resonance frequency increases. It is concluded that attaching an electrode plate with a T-shaped configuration to the end of the cantilever microbeam results in a configuration with larger pull-in voltage and smaller nonlinear shift of the resonance frequency compared to the configuration in which the electrode plate is directly attached to it.

Vertical polarization-induced doping InN/InGaN heterojunction tunnel FET with hetero T-shaped gate

A novel vertical InN/InGaN heterojunction tunnel FET with hetero T-shaped gate as well as polarization-doped source and drain region(InN-Hetero-TG-TFET)is proposed and investigated by Silvaco-Atlas simulations for the first time.Compared with the conventional physical doping TFET devices,the proposed device can realize the P-type source and N-type drain region by means of the polarization effect near the top InN/InGaN and bottom InGaN/InN heterojunctions respectively,which could provide an effective solution of random dopant fluctuation(RDF)and the related problems about the high thermal budget and expensive annealing techniques due to ion-implantation physical doping.Besides,due to the hetero T-shaped gate,the improvement of the on-state performance can be achieved in the proposed device.The simulations of the device proposed here in this work show ION of 4.45×10^(-5)A/μm,ION/IOFF ratio of 10^(13),and SS_(avg)of 7.5 mV/dec in InN-Hetero-TG-TFET,which are better than the counterparts of the device with a homo T-shaped gate(InN-Homo-TG-TFET)and our reported lateral polarization-induced InN-based TFET(PI-InN-TFET).These results can provide useful reference for further developing the TFETs without physical doping process in low power electronics applications.

Stresses due to an adhesion crack in T-shaped junction of two orthotropic plates

The general solution of stresses is derived for a T-shaped junction of two thin plates with an adhesion crack. The plates are orthotropic. A shear force is applied on the crack surface. The analysis is based on the supposition that the stresses in each plate can be approximated by a plane stress condition. The results obtained are verified by numerical calculation of FEM.

SYNTHESIS OF LIQUID CRYSTALLINE COPOLYESTERS WITH T-SHAPED TWO-DIMENSIONAL MESOGENIC UNIT AND CROWN ETHER CYCLE

A novel series of liquid crystalline copolyesters with T-shaped two-dimensional mesogenic unit and crown ether cycle of cis-4,4′-bis(4-hydroxyphenylazo)dibenzo-18-crown-6 was prepared via solution condensation polymerization from 4,4′-(α,ω-hexanedioyloxy)dibenzoyl dichloride(M_1),2-(4′-ethoxyphenyl)hydroquinone(M_2)and cis-4,4′-bis(4- hydroxyphenylazo)dibenzo-18-crown-6(M_3).The molecular weights of copolyesters are not high,and the intrinsic viscosity [η]of copolyesters ranges from 0.29-0.43.The monomers ...

Research on the navigation method of large-scale differential tail-control improvised guided munitions based on rotational speed constraints

In the process of launching guided projectile under the conventional system, it is difficult to effectively obtain the precise navigation parameters of the projectile in the high dynamic environment. Aiming at this problem, this paper describes a new system of guided ammunition based on tail spin reduction. After analyzing the mechanism of the ammunition's tail spin reduction, a navigation method of large scale difference tail control simple guided ammunition based on speed constraint is proposed. In this method,the corresponding navigation constraints can be carried out by combining the rotation speed state of the ammunition itself, and the optimal solution of navigation parameters during the flight of the missile can be obtained by Extended Kalman Filter(EKF). Finally, the performance of the proposed method was verified by the simulation environment, and the hardware-in-the-loop simulation test and flight test were carried out to verify the performance of the method in the real environment. The experimental results show that the proposed method can achieve the optimal estimation of navigation parameters for simple guided ammunition with large-scale difference tail control. Under the conditions of simulation test and hardware-in-loop simulation test, the position and velocity errors calculated by the method in this paper converged. Under the condition of flight test, the spatial average error calculated by the method described in this paper is 6.17 m, and the spatial error of the final landing point is 3.50 m.Through this method, the accurate acquisition of navigation parameters in the process of projectile launching is effectively realized.

Reinforcing effects of polypropylene on energy absorption and fracturing of cement-based tailings backfill under impact loading

Polypropylene(PP)fiber-reinforced cement-based tailings backfill(FRCTB)is a green compound material with superior crack resistance and has good prospects for application in underground mining.However,FRCTB exhibits susceptibility to dynamic events,such as impact ground pressure and blast vibrations.This paper investigates the energy and crack distribution behavior of FRCTB under dynamic impact,considering the height/diameter(H/D)effect.Split Hopkinson pressure bar,industrial computed tomography scan,and scanning electron microscopy(SEM)experiments were carried out on six types of FRCTB.Laboratory outcomes confirmed fiber aggregation at the bottom of specimens.When H/D was less than 0.8,the proportion of PP fibers distributed along theθangle direction of80°-90°increased.For the total energy,all samples presented similar energy absorption,reflectance,and transmittance.However,a rise in H/D may cause a rise in the energy absorption rate of FRCTB during the peak phase.A positive correlation existed between the average strain rate and absorbed energy per unit volume.The increase in H/D resulted in a decreased crack volume fraction of FRCTB.When the H/D was greater than or equal to 0.7,the maximum crack volume fraction of FRCTB was observed close to the incidence plane.Radial cracks were present only in the FRCTB with an H/D ratio of 0.5.Samples with H/D ratios of 0.5 and 0.6 showed similar distributions of weakly and heavily damaged areas.PP fibers can limit the emergence and expansion of cracks by influencing their path.SEM observations revealed considerable differences in the bonding strengths between fibers and the FRCTB.Fibers that adhered particularly well to the substrate were attracted together with the hydration products adhering to surfaces.These results show that FRCTB is promising as a sustainable and green backfill for determining the design properties of mining with backfill.

Rheological properties and concentration evolution of thickened tailings under the coupling effect of compression and shear

Cemented paste backfill(CPB)is a key technology for green mining in metal mines,in which tailings thickening comprises the primary link of CPB technology.However,difficult flocculation and substandard concentrations of thickened tailings often occur.The rheological properties and concentration evolution in the thickened tailings remain unclear.Moreover,traditional indoor thickening experiments have yet to quantitatively characterize their rheological properties.An experiment of flocculation condition optimization based on the Box-Behnken design(BBD)was performed in the study,and the two response values were investigated:concentration and the mean weighted chord length(MWCL)of flocs.Thus,optimal flocculation conditions were obtained.In addition,the rheological properties and concentration evolution of different flocculant dosages and ultrafine tailing contents under shear,compression,and compression-shear coupling experimental conditions were tested and compared.The results show that the shear yield stress under compression and compression-shear coupling increases with the growth of compressive yield stress,while the shear yield stress increases slightly under shear.The order of shear yield stress from low to high under different thickening conditions is shear,compression,and compression-shear coupling.Under compression and compression-shear coupling,the concentration first rapidly increases with the growth of compressive yield stress and then slowly increases,while concentration increases slightly under shear.The order of concentration from low to high under different thickening conditions is shear,compression,and compression-shear coupling.Finally,the evolution mechanism of the flocs and drainage channels during the thickening of the thickened tailings under different experimental conditions was revealed.

Kondo-Fano Effect in T-shaped Double Quantum Dots Coupled to Ferromagnetic Leads

Using an equation-of-motion technique, we theoretically study the Kondo-Fano effect in the T-shaped double quantum dots coupled to two ferromagnetic leads by the Anderson Hamiltonian. We calculate the density of states in this system by solving Green function. Our results reveal that the density of states show some noticeable characteristics not only depending upon the interdot coupling tab, the energy level eal of the side coupled quantum dot QDb, and the relative angle θ of magnetic moment M, but also the asymmetry parameter a in ferromagnetic leads and so on. All these parameters greatly influence the density of states of the eentral quantum dot QDa. This system is a possible candidate for spin valve transistors and may have potential applications in the spintronies.

SYNTHESIS AND CHARACTERIZATION OF LIQUID CRYSTAL POLYMERS WITH T-SHAPED TWO-DIMENSIONAL MESOGENIC UNITS (Ⅱ)

A series of liquid crystalline polymers with T-shaped two-dimensional mesogenic unitswere synthesized via low temperature solution polycondensation of 2-(4'-alkoxy-phenyl)hydroquinone with various diacyl dichlorides. The polymers were found to be nematic andshown thermotropic liquid crystalline behaviors through observations using DSC, polarizedmicroscopy and X-ray diffraction. The melting temperature T_m and the isotropizationtemperature T_i of the polymers change regularly with varying of the monomer structures.

SYNTHESIS AND CHARACTERIZATION OF LIQUID CRYSTAL POLYESTERS WITH T-SHAPED TWO-DIMENSIONAL MESOGENIC UNITS(Ⅲ)

A new series of liquid crystal polyesters with T-shaped two-dimensional mesogenic units weresynthesized by melt polycondensation of the diacetates of 2-(4'-alkoxy -phenyl)-hydroquinones with 4,4'-alkylenedioxydibenzoic acid. The polymers were characterized by using polarized microscopy, DSC and X-ray diffraction. It was realized that all the polymers have nematic thermotropic liquid crystallinecharacteristics. The melting temperature (T_m) and isotropization temperature (T_i) of the polymers changeregularly with varying lengths of the alkoxy side group and the length of the alkylene group in the main chainin company with an even-odd effect. The mesophase temperature range also varies regularly with the polymerstructure. It is shown that the mesophase range has been widened.

Design and Implementation of T-Shaped Planar Antenna for MIMO Applications

This paper proposes,demonstrates,and describes a basic T-shaped Multi-Input and Multi-Output(MIMO)antenna with a resonant frequency of 3.1 to 10.6 GHz.Compared with the U-shaped antenna,the mutual coupling is minimized by using a T-shaped patch antenna.The T-shaped patch antenna shapes filter properties are tested to achieve separation over the 3.1 to 10.6 GHz frequency range.The parametric analysis,including width,duration,and spacing,is designed in the MIMO applications for good isolation.On the FR4 substratum,the configuration of MIMO is simulated.The appropriate dielectric material ε_(r)=4.4 is introduced using this contribution and application array feature of the MIMO systems.In this paper,FR4 is used due to its high dielectric strength and low cost.For 3.1 to 10.6 GHz and 3SRR,T-shaped patch antennas are used in the field to increase bandwidth.The suggested Tshaped MIMO antenna is calculated according to the HFSS 13.0 program simulation performances.The antenna suggested is,therefore,a successful WLAN candidate.

Dynamic behavior of outburst two-phase flow in a coal mine T-shaped roadway:The formation of impact airflow and its disaster-causing effect

The study of the dynamic disaster mechanism of coal and gas outburst two-phase flow is crucial for improving disaster reduction and rescue ability of coal mine outburst accidents.An outburst test in a T-shaped roadway was conducted using a self-developed large-scale outburst dynamic disaster test system.We investigated the release characteristics of main energy sources in coal seam,and obtained the dynamic characteristics of outburst two-phase flow in a roadway.Additionally,we established a formation model for outburst impact flow and a model for its flow in a bifurcated structure.The results indicate that the outburst process exhibits pulse characteristics,and the rapid destruction process of coal seam and the blocking state of gas flow are the main causes of the pulse phenomenon.The outburst energy is released in stages,and the elastic potential energy is released in the vertical direction before the horizontal direction.In a straight roadway,the impact force oscillates along the roadway.With an increase in the solid–gas ratio,the two-phase flow impact force gradually increases,and the disaster range extends from the middle of the roadway to the coal seam.In the area near the coal seam,the disaster caused by the two-phase flow impact is characterized by intermittent recovery.In a bifurcated roadway,the effect of impact airflow on impact dynamic disaster is much higher than that of two-phase flow,and the impact force tends to weaken with increasing solid-gas ratio.The impact force is asymmetrically distributed;it is higher on the left of the bifurcated roadway.With an increase in the solid-gas ratio,the static pressure rapidly decreases,and the bifurcated structure accelerates the attenuation of static pressure.Moreover,secondary acceleration is observed when the shock wave moves along the T-shaped roadway,indicating that the bifurcated structure increases the shock wave velocity.

CPW Fed Double T-Shaped Array Antenna with Suppressed Mutual Coupling

A compact CPW-fed double T-Shaped antenna is proposed for dual-band wireless local area network (WLAN) operations. For the proposed antenna, the -10 dB return loss bandwidth could reach about 25.5% for the 2.4 GHz band and 5.7 % for the 5 GHz band, which meet the required bandwidth specification of WLAN standard. To reduce the mutual coupling and get high isolation between two dual-band antennas, we proposed the novel electromagnetic band gap (EBG) structures. When the EBG structure is employed, a -13dB and -30dB mutual coupling reduction is achieved at 2.4 and 5.2 GHz. It shows that the features of small size, uniplanar structure, good radiation characteristics and small mutual coupling are promising for multi-input multi-output (MIMO) applications.

A method for coastal oil tank detection in polarimetric SAR images based on recognition of T-shaped harbor

To automatically detect oil tanks in polarimetric synthetic aperture radar（SAR） images, a coastal oil tank detection method is proposed based on recognition of T-shaped harbor. First of all, the T-shaped harbor is detected to locate the region of interest（ROI） of oil tanks. Then all suspicious targets in the ROI are extracted by the segmentation of strong scattering targets and the classifier of H/α. The template targets are selected from the suspicious targets by the combination of a proposed circular degree parameter and the similarity parameter（SP） of the polarimetric coherency matrix. Finally, oil tanks are detected according to the statistics of the similarity parameter between each suspicious target and template targets in ROI. Polarimetric SAR data acquired by RADARSAT-2 over Berkeley and Singapore areas are used for testing. Experiment results show that most of the targets are correctly detected and the overall detection rate is close to 80%.The false rate is effectively reduced by the proposed algorithm compared with the method without T-shaped harbor recognition.

Novel Preparation of Magnetic Microcapsules by Using T-Shaped Microchannel Reactor

Traditional preparation of magnetic microcapsules involves cumbersome processes and often results in irregular-shaped products. Due to the stable laminar flow of reaction solution and the moderate reaction conditions, the T-shaped microchannel (T-MC) reactor is supposed to yield microcapsules with regular shape. In this paper, magnetic particles of ferroferric oxide modified by oleic acid (OA-Fe3O4) and dispersed in tetrachloroethylene were used as core material. Polymethyl methacrylate (PMMA) was used as shell material. Magnetic microcapsules were prepared by using a T-MC reactor. Factors that influenced the encapsulated reaction were investigated in details, which included the velocity ratio of aqueous phase to oil phase, the length and the inner diameter of the microchannel. The morphology, composition, and magnetic responsiveness of the magnetic microcapsules were analyzed and characterized by SEM, FTIR, XRD, TGA, and vibrating sample magnetometer (VSM). The results confirmed that magnetic microcapsules prepared by T-MC reactor were regular in shape.