Effects of welding parameters and welding sequence on residual stress and distortion in Al6061-T6 aluminum alloy for T-shaped welded joint

The distribution of temperature and then the distribution of residual stress and distortion in the stiffened aluminum alloy Al6061-T6 plates under the metal inert gas(MIG)welding process were investigated by three dimensional thermo-mechanical coupled finite element model using Ansys software.The properties of materials were considered temperature-dependent and the filler metal was added to the workpiece by the element birth and death technique.In three modes of current,two different speeds and two various sequences,the distribution of residual stress and distortion were calculated and analyzed.The results showed that increase in welding speed decreased the vertical deflection in the plate,transverse shrinkage and angular distortion of plate and the lateral deflection of stiffener,but increased the maximum longitudinal tensile stress in the plate and stiffener.Furthermore,increase in current increased the residual stress and deformation in the plate and stiffener,and the change in the welding sequence changed the distribution of the distortion in the plate and the stiffener without significant change in the distribution of the longitudinal residual stress.

Influences of fillet radius and draft angle on local loading process of titanium alloy T-shaped components

In order to study influences of geometric parameters on the T-shaped components local loading process, a new mathematical model considering the fillet radius and draft angle was established by using the slab method. The results obtained by the mathematical model agree with the data form experiment and numerical simulation, and the results are closer to the experimental and simulation results. The influence of draft angle may be neglected under the forming conditions used. The influence of fillet radius is notable, especially in the case that the ratio of fillet radius to rib width is less than 0.75.

Performance of a Self-Aligned InP/GaInAs SHBT with a Novel T-Shaped Emitter

A self-aligned InP/GalnAs single heterojunction bipolar transistor（HBT） is investigated using a novel T-shaped emitter. A U-shaped emitter layout,selective wet etching,laterally etched undercut, and an air-bridge are applied in this process. The device, which has a 2μm×12μm U-shaped emitter area,demonstrates a common-emitter DC current gain of 170,an offset voltage of 0.2V,a knee voltage of 0.5V, and an open-base breakdown voltage of over 2V. The HBT exhibits good microwave performance with a current gain cutoff frequency of 85GHz and a maximum oscillation frequency of 72GHz, These results indicate that these InP/InGaAs SHBTs are suitable for low-voltage,low-power,and high-frequency applications.

Improved design of special boundary elements for T-shaped reinforced concrete walls

This study examines the design provisions of the Chinese GB 50011-2010 code for seismic design of buildings for the special boundary elements of T-shaped reinforced concrete walls and proposes an improved design method. Comparison of the design provisions of the GB 50011-2010 code and those of the American code ACI 318-14 indicates a possible deficiency in the T-shaped wall design provisions in GB 50011-2010. A case study of a typical T-shaped wall designed in accordance with GB 50011-2010 also indicates the insufficient extent of the boundary element at the non-flange end and overly conservative design of the flange end boundary element. Improved designs for special boundary elements ofT-shaped walls are developed using a displacement-based method. The proposed design formulas produce a longer boundary element at the non-flange end and a shorter boundary element at the flange end, relative to those of the GB 50011-2010 provisions. Extensive numerical analysis indicates that T-shaped walls designed using the proposed formulas develop inelastic drift of 0.01 for both cases of the flange in compression and in tension.

Numerical investigation of flow pattern and components of three-dimensional velocity around a submerged T-shaped spur dike in a 90° bend

Spur dike is one of the river training structures. This work presented a numerical simulation of flow field and three-dimensional velocity around a T-shaped spur dike located in bend using SSIIM model. The main objective of this work is to investigate the three-dimensional velocities and streamlines at transverse and longitudinal sections and plan views around the T-shaped spur dike in different submergence ratios(0, 5%, 15%, 25% and 50%). It is concluded that by increasing the submergence ratio from 5% to 50%, the maximum of scour is reduced; the maximum of longitudinal velocity increases by 7.7% and occurs at the water surface in spur dike axis. Near the bed, the maximum of vertical velocity occurs at the end of spur wing. By analyzing the streamlines at transverse sections, the followings were deduced for different submergence ratios: different dimensions and different positions of vortices around the spur dike.

Static and dynamic responses of a microcantilever with a T-shaped tip mass to an electrostatic actuation

In this study, nonlinear static and dynamic responses of a microcantilever with a T-shaped tip mass excited by electrostatic actuations are investigated. The electrostatic force is generated by applying an electric voltage between the horizontal part of T-shaped tip mass and an opposite electrode plate. The cantilever microbeam is modeled as an Euler-Bernoulli beam. The T-shaped tip mass is assumed to be a rigid body and the nonlinear effect of electrostatic force is considered. An equation of motion and its associated boundary conditions are derived by the aid of combining the Hamilton principle and Newton’s method. An exact solution is obtained for static deflection and mode shape of vibration around the static position. The differential equation of nonlinear vibration around the static position is discretized using the Galerkin method. The system mode shapes are used as its related comparison functions. The discretized equations are solved by the perturbation theory in the neighborhood of primary and subharmonic resonances. In addition, effects of mass inertia, mass moment of inertia as well as rotation of the T-shaped mass, which were ignored in previous works, are considered in the analysis. It is shown that by increasing the length of the horizontal part of the T-shaped mass, the amount of static deflection increases, natural frequency decreases and nonlinear shift of the resonance frequency increases. It is concluded that attaching an electrode plate with a T-shaped configuration to the end of the cantilever microbeam results in a configuration with larger pull-in voltage and smaller nonlinear shift of the resonance frequency compared to the configuration in which the electrode plate is directly attached to it.

Analytical Modeling of Fluid Sloshing in A 2D Rectangular Container with A Bottom-Mounted T-Shaped Baffle

An analytical procedure is presented to evaluate the fluid sloshing characteristics in a two-dimensional(2D)rectangular container with a bottom-mounted T-shaped baffle.The fluid region is divided into several sub-domains with hypothetical interfaces and the velocities and pressures of the fluid on adjacent interfaces should be identical.The separation of variables in conjunction with the superposition principle is employed to formulate the velocity potential of each sub-domain.The Fourier series expansion is used to derive the eigenvalue equation by substituting the velocity potential solutions into the free surface conditions and the continuity conditions on adjacent interfaces.Under the horizontal base excitation,the total velocity potential of fluid is decomposed of the impulsive and perturbed velocity potentials.The orthogonality of the sloshing modes is demonstrated by implementing Gauss formula.The dynamic response equation is established by incorporating the total velocity potential solution into the surface wave equation.Excellent agreements are achieved between the present results and those from the reported literature and finite element code.Numerical results are exhibited to reveal the effect of the baffle parameters and excitation frequency on sloshing characteristics and responses of liquid.

Vertical polarization-induced doping InN/InGaN heterojunction tunnel FET with hetero T-shaped gate

A novel vertical InN/InGaN heterojunction tunnel FET with hetero T-shaped gate as well as polarization-doped source and drain region(InN-Hetero-TG-TFET)is proposed and investigated by Silvaco-Atlas simulations for the first time.Compared with the conventional physical doping TFET devices,the proposed device can realize the P-type source and N-type drain region by means of the polarization effect near the top InN/InGaN and bottom InGaN/InN heterojunctions respectively,which could provide an effective solution of random dopant fluctuation(RDF)and the related problems about the high thermal budget and expensive annealing techniques due to ion-implantation physical doping.Besides,due to the hetero T-shaped gate,the improvement of the on-state performance can be achieved in the proposed device.The simulations of the device proposed here in this work show ION of 4.45×10^(-5)A/μm,ION/IOFF ratio of 10^(13),and SS_(avg)of 7.5 mV/dec in InN-Hetero-TG-TFET,which are better than the counterparts of the device with a homo T-shaped gate(InN-Homo-TG-TFET)and our reported lateral polarization-induced InN-based TFET(PI-InN-TFET).These results can provide useful reference for further developing the TFETs without physical doping process in low power electronics applications.

基于SYSWELD的等高齿弧锥齿轮铣刀盘多层焊接数值模拟

本文借助Visual-Environment焊接模拟仿真软件,以SYSWELD为求解器对等高齿弧锥齿轮铣刀盘V形坡口多层焊接的焊接温度场进行数值模拟,得到了焊接温度场分布云图,分析并对比了每层焊缝中心、焊趾及距焊缝中心5mm处的温度循环曲线,推导出三层焊接温度场公式用于计算验证。结果表明,熔池中心温度最高,距离焊缝中心越近,温度梯度变化越大。

基于SYSWELD的大厚板窄间隙双丝埋弧焊热过程数值模拟

基于60 mm厚Q345R钢,开展了窄间隙双丝埋弧焊焊接试验,得到了合理的工艺参数,焊缝成型平整均匀无任何缺陷.通过SYSWELD有限元软件对大厚板窄间隙双丝埋弧焊焊接热过程进行数值模拟分析,模拟的熔池宽与高和实际相比,误差率均控制在5%以内,并利用热电偶装置测得热影响区热循环曲线与模拟的热循环曲线变化趋势基本一致,具有升温快,降温慢的特点,验证了该模型的有效性.为后续利用该模型,进一步探究不同参数或边界条件对于大厚板窄间隙双丝埋弧焊焊接热过程与应力-应变规律提供理论指导.

Stresses due to an adhesion crack in T-shaped junction of two orthotropic plates

The general solution of stresses is derived for a T-shaped junction of two thin plates with an adhesion crack. The plates are orthotropic. A shear force is applied on the crack surface. The analysis is based on the supposition that the stresses in each plate can be approximated by a plane stress condition. The results obtained are verified by numerical calculation of FEM.

A review of linear friction welding of Ni -based superalloys

Ni-based superalloys are one of the most important materials employed in high-temperature applications within the aerospace and nuclear energy industries and in gas turbines due to their excellent corrosion,radiation,fatigue resistance,and high-temperature strength.Linear friction welding(LFW)is a new joining technology with near-net-forming characteristics that can be used for the manu-facture and repair of a wide range of aerospace components.This paper reviews published works on LFW of Ni-based superalloys with the aim of understanding the characteristics of frictional heat generation and extrusion deformation,microstructures,mechanical proper-ties,flash morphology,residual stresses,creep,and fatigue of Ni-based superalloy weldments produced with LFW to enable future optim-um utilization of the LFW process.

Effect of Interface Form on Creep Failure and Life of Dissimilar Metal Welds Involving Nickel-Based Weld Metal and Ferritic Base Metal

For dissimilar metal welds(DMWs)involving nickel-based weld metal(WM)and ferritic heat resistant steel base metal(BM)in power plants,there must be an interface between WM and BM,and this interface suffers mechanical and microstructure mismatches and is often the rupture location of premature failure.In this study,a new form of WM/BM interface form,namely double Y-type interface was designed for the DMWs.Creep behaviors and life of DMWs containing double Y-type interface and conventional I-type interface were compared by finite element analysis and creep tests,and creep failure mechanisms were investigated by stress-strain analysis and microstructure characterization.By applying double Y-type interface instead of conventional I-type interface,failure location of DMW could be shifted from the WM/ferritic heat-affected zone(HAZ)interface into the ferritic HAZ or even the ferritic BM,and the failure mode change improved the creep life of DMW.The interface premature failure of I-type interface DMW was related to the coupling effect of microstructure degradation,stress and strain concentrations,and oxide notch on the WM/HAZ interface.The creep failure of double Y-type interface DMW was the result of Type IV fracture due to the creep voids and micro-cracks on fine-grain boundaries in HAZ,which was a result of the matrix softening of HAZ and lack of precipitate pinning at fine-grain boundaries.The double Y-type interface form separated the stress and strain concentrations in DMW from the WM/HAZ interface,preventing the trigger effect of oxide notch on interface failure and inhibiting the interfacial microstructure cracking.It is a novel scheme to prolong creep life and enhance reliability of DMW,by means of optimizing the interface form,decoupling the damage factors from WM/HAZ interface,and then changing the failure mechanism and shifting the failure location.

SYNTHESIS OF LIQUID CRYSTALLINE COPOLYESTERS WITH T-SHAPED TWO-DIMENSIONAL MESOGENIC UNIT AND CROWN ETHER CYCLE

A novel series of liquid crystalline copolyesters with T-shaped two-dimensional mesogenic unit and crown ether cycle of cis-4,4′-bis(4-hydroxyphenylazo)dibenzo-18-crown-6 was prepared via solution condensation polymerization from 4,4′-(α,ω-hexanedioyloxy)dibenzoyl dichloride(M_1),2-(4′-ethoxyphenyl)hydroquinone(M_2)and cis-4,4′-bis(4- hydroxyphenylazo)dibenzo-18-crown-6(M_3).The molecular weights of copolyesters are not high,and the intrinsic viscosity [η]of copolyesters ranges from 0.29-0.43.The monomers ...

Kondo-Fano Effect in T-shaped Double Quantum Dots Coupled to Ferromagnetic Leads

Using an equation-of-motion technique, we theoretically study the Kondo-Fano effect in the T-shaped double quantum dots coupled to two ferromagnetic leads by the Anderson Hamiltonian. We calculate the density of states in this system by solving Green function. Our results reveal that the density of states show some noticeable characteristics not only depending upon the interdot coupling tab, the energy level eal of the side coupled quantum dot QDb, and the relative angle θ of magnetic moment M, but also the asymmetry parameter a in ferromagnetic leads and so on. All these parameters greatly influence the density of states of the eentral quantum dot QDa. This system is a possible candidate for spin valve transistors and may have potential applications in the spintronies.

SYNTHESIS AND CHARACTERIZATION OF LIQUID CRYSTAL POLYMERS WITH T-SHAPED TWO-DIMENSIONAL MESOGENIC UNITS (Ⅱ)

A series of liquid crystalline polymers with T-shaped two-dimensional mesogenic unitswere synthesized via low temperature solution polycondensation of 2-(4'-alkoxy-phenyl)hydroquinone with various diacyl dichlorides. The polymers were found to be nematic andshown thermotropic liquid crystalline behaviors through observations using DSC, polarizedmicroscopy and X-ray diffraction. The melting temperature T_m and the isotropizationtemperature T_i of the polymers change regularly with varying of the monomer structures.

SYNTHESIS AND CHARACTERIZATION OF LIQUID CRYSTAL POLYESTERS WITH T-SHAPED TWO-DIMENSIONAL MESOGENIC UNITS(Ⅲ)

A new series of liquid crystal polyesters with T-shaped two-dimensional mesogenic units weresynthesized by melt polycondensation of the diacetates of 2-(4'-alkoxy -phenyl)-hydroquinones with 4,4'-alkylenedioxydibenzoic acid. The polymers were characterized by using polarized microscopy, DSC and X-ray diffraction. It was realized that all the polymers have nematic thermotropic liquid crystallinecharacteristics. The melting temperature (T_m) and isotropization temperature (T_i) of the polymers changeregularly with varying lengths of the alkoxy side group and the length of the alkylene group in the main chainin company with an even-odd effect. The mesophase temperature range also varies regularly with the polymerstructure. It is shown that the mesophase range has been widened.

Design and Implementation of T-Shaped Planar Antenna for MIMO Applications

This paper proposes,demonstrates,and describes a basic T-shaped Multi-Input and Multi-Output(MIMO)antenna with a resonant frequency of 3.1 to 10.6 GHz.Compared with the U-shaped antenna,the mutual coupling is minimized by using a T-shaped patch antenna.The T-shaped patch antenna shapes filter properties are tested to achieve separation over the 3.1 to 10.6 GHz frequency range.The parametric analysis,including width,duration,and spacing,is designed in the MIMO applications for good isolation.On the FR4 substratum,the configuration of MIMO is simulated.The appropriate dielectric material ε_(r)=4.4 is introduced using this contribution and application array feature of the MIMO systems.In this paper,FR4 is used due to its high dielectric strength and low cost.For 3.1 to 10.6 GHz and 3SRR,T-shaped patch antennas are used in the field to increase bandwidth.The suggested Tshaped MIMO antenna is calculated according to the HFSS 13.0 program simulation performances.The antenna suggested is,therefore,a successful WLAN candidate.

Dynamic behavior of outburst two-phase flow in a coal mine T-shaped roadway:The formation of impact airflow and its disaster-causing effect

The study of the dynamic disaster mechanism of coal and gas outburst two-phase flow is crucial for improving disaster reduction and rescue ability of coal mine outburst accidents.An outburst test in a T-shaped roadway was conducted using a self-developed large-scale outburst dynamic disaster test system.We investigated the release characteristics of main energy sources in coal seam,and obtained the dynamic characteristics of outburst two-phase flow in a roadway.Additionally,we established a formation model for outburst impact flow and a model for its flow in a bifurcated structure.The results indicate that the outburst process exhibits pulse characteristics,and the rapid destruction process of coal seam and the blocking state of gas flow are the main causes of the pulse phenomenon.The outburst energy is released in stages,and the elastic potential energy is released in the vertical direction before the horizontal direction.In a straight roadway,the impact force oscillates along the roadway.With an increase in the solid–gas ratio,the two-phase flow impact force gradually increases,and the disaster range extends from the middle of the roadway to the coal seam.In the area near the coal seam,the disaster caused by the two-phase flow impact is characterized by intermittent recovery.In a bifurcated roadway,the effect of impact airflow on impact dynamic disaster is much higher than that of two-phase flow,and the impact force tends to weaken with increasing solid-gas ratio.The impact force is asymmetrically distributed;it is higher on the left of the bifurcated roadway.With an increase in the solid-gas ratio,the static pressure rapidly decreases,and the bifurcated structure accelerates the attenuation of static pressure.Moreover,secondary acceleration is observed when the shock wave moves along the T-shaped roadway,indicating that the bifurcated structure increases the shock wave velocity.

CPW Fed Double T-Shaped Array Antenna with Suppressed Mutual Coupling

A compact CPW-fed double T-Shaped antenna is proposed for dual-band wireless local area network (WLAN) operations. For the proposed antenna, the -10 dB return loss bandwidth could reach about 25.5% for the 2.4 GHz band and 5.7 % for the 5 GHz band, which meet the required bandwidth specification of WLAN standard. To reduce the mutual coupling and get high isolation between two dual-band antennas, we proposed the novel electromagnetic band gap (EBG) structures. When the EBG structure is employed, a -13dB and -30dB mutual coupling reduction is achieved at 2.4 and 5.2 GHz. It shows that the features of small size, uniplanar structure, good radiation characteristics and small mutual coupling are promising for multi-input multi-output (MIMO) applications.