Optimizing Average Electric Power During the Charging of Lithium-Ion Batteries Through the Taguchi Method

In recent times, lithium-ion batteries have been widely used owing to their high energy density, extended cycle lifespan, and minimal self-discharge rate. The design of high-speed rechargeable lithium-ion batteries faces a significant challenge owing to the need to increase average electric power during charging. This challenge results from the direct influence of the power level on the rate of chemical reactions occurring in the battery electrodes. In this study, the Taguchi optimization method was used to enhance the average electric power during the charging process of lithium-ion batteries. The Taguchi technique is a statistical strategy that facilitates the systematic and efficient evaluation of numerous experimental variables. The proposed method involved varying seven input factors, including positive electrode thickness, positive electrode material, positive electrode active material volume fraction, negative electrode active material volume fraction, separator thickness, positive current collector thickness, and negative current collector thickness. Three levels were assigned to each control factor to identify the optimal conditions and maximize the average electric power during charging. Moreover, a variance assessment analysis was conducted to validate the results obtained from the Taguchi analysis. The results revealed that the Taguchi method was an eff ective approach for optimizing the average electric power during the charging of lithium-ion batteries. This indicates that the positive electrode material, followed by the separator thickness and the negative electrode active material volume fraction, was key factors significantly infl uencing the average electric power during the charging of lithium-ion batteries response. The identification of optimal conditions resulted in the improved performance of lithium-ion batteries, extending their potential in various applications. Particularly, lithium-ion batteries with average electric power of 16 W and 17 W during charging were designed and simulated in the range of 0-12000 s using COMSOL Multiphysics software. This study efficiently employs the Taguchi optimization technique to develop lithium-ion batteries capable of storing a predetermined average electric power during the charging phase. Therefore, this method enables the battery to achieve complete charging within a specific timeframe tailored to a specificapplication. The implementation of this method can save costs, time, and materials compared with other alternative methods, such as the trial-and-error approach.

Design Optimization of a Self-circulated Hydrogen Cooling System for a PM Wind Generator Based on Taguchi Method

With the continuous improvement of permanent magnet(PM)wind generators'capacity and power density,the design of reasonable and efficient cooling structures has become a focus.This paper proposes a fully enclosed self-circulating hydrogen cooling structure for a originally forced-air-cooled direct-drive PM wind generator.The proposed hydrogen cooling system uses the rotor panel supports that hold the rotor core as the radial blades,and the hydrogen flow is driven by the rotating plates to flow through the axial and radial vents to realize the efficient cooling of the generator.According to the structural parameters of the cooling system,the Taguchi method is used to decouple the structural variables.The influence of the size of each cooling structure on the heat dissipation characteristic is analyzed,and the appropriate cooling structure scheme is determined.

Multi-Objective Optimization of Fused Deposition Modeling for Mechanical Properties of Biopolymer Parts Using the Grey-Taguchi Method

The urgent need to develop customized functional products only possible by 3D printing had realized when faced with the unavailability of medical devices like surgical instruments during the coronavirus-19 disease and the ondemand necessity to perform surgery during space missions.Biopolymers have recently been the most appropriate option for fabricating surgical instruments via 3D printing in terms of cheaper and faster processing.Among all 3D printing techniques,fused deposition modelling(FDM)is a low-cost and more rapid printing technique.This article proposes the fabrication of surgical instruments,namely,forceps and hemostat using the fused deposition modeling(FDM)process.Excellent mechanical properties are the only indicator to judge the quality of the functional parts.The mechanical properties of FDM-processed parts depend on various process parameters.These parameters are layer height,infill pattern,top/bottom pattern,number of top/bottom layers,infill density,flow,number of shells,printing temperature,build plate temperature,printing speed,and fan speed.Tensile strength and modulus of elasticity are chosen as evaluation indexes to ascertain the mechanical properties of polylactic acid(PLA)parts printed by FDM.The experiments have performed through Taguchi’s L27orthogonal array(OA).Variance analysis(ANOVA)ascertains the significance of the process parameters and their percent contributions to the evaluation indexes.Finally,as a multiobjective optimization technique,grey relational analysis(GRA)obtains an optimal set of FDM process parameters to fabricate the best parts with comprehensive mechanical properties.Scanning electron microscopy(SEM)examines the types of defects and strong bonding between rasters.The proposed research ensures the successful fabrication of functional surgical tools with substantial ultimate tensile strength(42.6 MPa)and modulus of elasticity(3274 MPa).

Optimum Design of Stair-Climbing Robots Using Taguchi Method

Environmental issues like pollution are major threats to human health.Many systems are developed to reduce pollution.In this paper,an optimal mobile robot design to reduce pollution in Green supply chain management system.Green supply chain management involves as similating environmentally and eco-nomically feasible solutions into the supply chain life-cycle.Smartness,advanced technologies,and advanced networks are becoming pillars of a sustainable supply chain management system.At the same time,there is much change happening in the logistics industry.They are moving towards a new logistics model.In the new model,robotic logistics has a vital role.The reasons for this change are the rapid growth of the e-commerce business and the shortage of workers.The advantages of using robotic logistics are reduction in human errors,faster delivery speed,better customer satisfaction,more safety for workers,and high workforce adaptability.A robot with rocker-bogie suspension is a six-wheeled mobile platform that has a distinctive potential to keep all wheels on the ground continuously.It has been designed to traverse rough and uneven terrain by distributing the load over its wheels equally.However,there is a limitation to achieving high-speed mobility against vertical barriers.In this research,an optimal design of product delivery wheeled robots for a sustainable supply chain system is proposed to ensure higher adaptability and maximum stability during climbing staircases.The design parameters of the proposed robot are optimized using Taguchi Method.The aim is to get a smooth trajectory of the robot’s center-of-mass.The proposed approach realizes a robot with much-improved stability which can climb over heights more than the size of the wheel(i.e.,3 times the radius of wheels).The results reveal that the modified rocker-bogie system not only increases the stair-climbing capability but also thwarts instability due to overturning of a wheel of the robot.

Design of Rotor Magnetic Barrier Structure of Built-in Permanent Magnet Motor Based on Taguchi Method

In this paper,a 20kW vehicle built-in permanent magnet synchronous motor is taken as an example,and a magnetic barrier structure is added to the rotor of the motor to solve the uneven saturation problem of the rotor side magnetic bridge.This structure improves the air-gap flux density waveform of the motor by influencing the internal magnetic flux path of the motor rotor,thus improving the sine of the no-load back EMF waveform of the motor and reducing the torque ripple of the motor.At the same time,Taguchi method is used to optimize the structural parameters of the added magnetic barrier.In order to facilitate the analysis of its uneven saturation phenomenon and improve the optimization effect,a simple equivalent magnetic network(EMN)model considering the uneven saturation of rotor magnetic bridge is established in this paper,and the initial values of optimization factors are selected based on this model.Finally,the no-load back EMF waveform distortion rate,torque ripple and output torque of the optimized motor are compared and analyzed,and the influence of magnetic barrier structure parameters on the electromagnetic performance of the motor is also analyzed.The results show that the optimized motor can not change the output torque of the motor as much as possible on the basis of reducing the waveform distortion rate of no-load back EMF and torque ripple.

Performance Investigation of Cone Dielectric Elastomer Actuator Using Taguchi Method

Dielectric elastomer actuator （DEA） show promise for mechatronic applications due to the advantages of dielectric elastomer, such as lightweight, flexible, low cost, high strain, etc, and many configurations of DEAs have been demonstrated. As a kind of linear actuator, cone DEAs are studied in some laboratory prototypes due to easy manufacturing, however, their performance have not been exploited fully. Based on the working principle of DEA, a four-bar linkage mechanism is designed to provide negative stiffness preload, which can increase displacement output of actuator （outer diameter 100 mm） to 17 mm. Three cone actuating units are assembled in parallel to enhance the maximum force output to 5.07 N. Loading experiments of actuator in forward and backward strokes are performed, the experimental results show that backward stroke has stronger actuating capability than forward stroke, accordingly application of actuator is recommended. Four factors rather than applied voltage, i.e., number of actuating units, pre-stretch ratio, inner diameter, and outer diameter, are determined as influencing factors for Taguchi method. Then the performance objectives of actuator, i.e., displacement output, maximum force output, and maximum work in backward stroke, are investigated based on L9（34） Taguchi orthogonal design. The mean signal-to-noise （S/N） ratio based on the larger-the-better criterion is calculated according to the acquired displacement and force output. Analytical results show that outer diameter has the most significant influence on displacement output, and maximum force out and work output are influenced most by number of actuating units. Inner diameter also has an important effect on the performance objectives of actuator, while pre-stretch ratio has the least influence. The proposed performance investigation is helpful for the design and application of cone actuator in mechatronic system.

Optimization of Polishing Parameters with Taguchi Method for LBO Crystal in CMP

Chemical mechanical polishing （CMP） was used to polish Lithium triborate （LiB3O5 or LBO） crystal. Taguchi method was applied for optimization of the polishing parameters. Material removal rate （MRR） and surface roughness are considered as criteria for the optimization. The polishing pressure, the abrasive concentration and the table velocity are important parameters which influence MRR and surface roughness in CMP of LBO crystal. Experiment results indicate that for MRR the polishing pressure is the most significant polishing parameter followed by table velocity; while for the surface roughness, the abrasive concentration is the most important one. For high MRR in CMP of LBO ctystal the optimal conditions are： pressure 620 g/cm^2, concentration 5.0 wt pct, and velocity 60 r/min, respectively. For the best surface roughness the optimal conditions are： pressure 416 g/cm^2, concentration 5.0 wt pct, and velocity 40 r/min, respectively. The contributions of individual parameters for MRR and surface roughness were obtained.

Statistical evaluation and optimization of zinc electrolyte hot purification process by Taguchi method

The neutral zinc sulfate solution obtained from hydrometallurgical process of Angouran zinc concentrate has cadmium, nickel and cobalt impurities, that must be purified before electrowinning. Therefore, cadmium and nickel are usually cemented out by addition of zinc dust and remained nickel and cobalt cemented out at second stage with zinc powder and arsenic trioxide. In this research, a new approach is described for determination of effective parameters and optimization of zinc electrolyte hot purification process using statistical design of experiments. The Taguchi method based on orthogonal array design（OAD） has been used to arrange the experimental runs. The experimental conditions involved in the work are as follows： the temperature range of 70-90 ℃ for reaction temperature（T）, 30-90 min for reaction time（t）, 2-4 g/L for zinc powder mass concentration（M）, one to five series for zinc dust particle size distributions（S1-S5）, and 0.1-0.5 g/L（C） for arsenic trioxide mass concentration. Optimum conditions for hot purification obtained in this work are T4（85 ℃）, t4=75 min, M4=3.5 g/L, S4（Serie 4）, and C2=0.2 g/L.

Study of M-ZSM-5 nanocatalysts(M: Cu, Mn, Fe, Co …) for selective catalytic reduction of NO with NH_3: Process optimization by Taguchi method

A series of different transition metals(V,Co,Cr,Mn,Fe,Ni,Cu and Zn) promoted H-ZSM-5 catalysts were prepared by impregnation method and characterized by X-ray diffraction(XRD),scanning electron microscopy(SEM) and transmission electron microscopy(TEM).The catalytic activity of these catalysts was evaluated for the selective catalytic reduction(SCR) of NO with NH_3 as reductant in the presence of oxygen.The results revealed that the catalytic activity of Cu-ZSM-5 nanocatalyst for NO conversion to N_2 was 80%at 300 ℃,which was the best among various promoted metals.Design of experiments(DOEs) with Taguchi method was employed to optimize NH_3-SCR process parameters such as NH_3/NO ratio,O_2 concentration,and gas hourly space velocity(GHSV) over Cu-ZSM-5 nanocatalyst at 250 and 300 ℃.Results showed that the most important parameter in NH_3-SCR of NO is O_2 concentration;followed by NH_3/NO ratio and GHSV has little importance.The NO conversion to N_2 of 63.1%and 94.86%was observed at 250℃ and 300℃,respectively under the obtained optimum conditions.

Identification of strategy parameters for particle swarm optimizer through Taguchi method

Particle swarm optimization （PSO）, like other evolutionary algorithms is a population-based stochastic algorithm inspired from the metaphor of social interaction in birds, insects, wasps, etc. It has been used for finding promising solutions in complex search space through the interaction of particles in a swarm. It is a well recognized fact that the performance of evolutionary algorithms to a great extent depends on the choice of appropriate strategy/operating parameters like population size, crossover rate, mutation rate, crossover operator, etc. Generally, these parameters are selected through hit and trial process, which is very unsystematic and requires rigorous experimentation. This paper proposes a systematic based on Taguchi method reasoning scheme for rapidly identifying the strategy parameters for the PSO algorithm. The Taguchi method is a robust design approach using fractional factorial design to study a large number of parameters with small number of experiments. Computer simulations have been performed on two benchmark functionsiRosenbrock function and Griewank functionito validate the approach.

Application for Optimization of New Soft Magnetic Material Motor by Taguchi Method

The application of new soft magnetic materials in permanent magnet motor can effectively reduce the loss of motor and improve the efficiency of motor. Taguchi method is a local multivariable and multi-objective optimization method widely used in various engineering problems, which can effectively improve the efficiency of engineering optimization. In this paper, based on a 25 kW, 1700 r/min three-phase permanent magnet motor, the relevant motor model is established in the finite element simulation software, and the relevant simulation analysis is carried out. Combined with Taguchi method optimization, the local optimal structure scheme is obtained. Through optimization, the motor can maintain high efficiency, reduce the cogging torque of the motor by 53.45%, reduce the torque ripple by 36.79%, and increase the torque generated by the permanent magnet per unit mass by 21.42%. Through this optimization, the overall performance of the motor has been significantly improved. The research content of this paper verifies the feasibility of the application of Taguchi method in the optimization of new soft magnetic material motor, provides a new idea for the optimization design of new soft magnetic material motor, and also provides a certain reference for the local multi-objective optimization of the electromagnetic structure of other similar motors.

Determining the Effect of Cutting Fluids on Surface Roughness in Turning AISI 1330 Alloy Steel Using Taguchi Method

Taguchi method has been employed to investigate the effects of cutting fluids on surface roughness in turning AISI 1330 alloy steel, using manually operated lathe machine. Experiments have been conducted using L27 (34) orthogonal array and each experiment was repeated three times and each test used a new cutting tool, High Speed Steel (HSS), to ensure accurate readings of the surface roughness. The statistical methods of Signal-to-Noise (S/N) ratio and the Analysis of Variance (ANOVA) were applied to investigate effects of cutting speed, feed rate and depth of cut on surface roughness under different cutting fluids. Minitab 14 software was used to analyze the effect of variables on the surface roughness. Results obtained indicated that optimal variables for the minimum surface roughness were cutting speed of 35 m/min (level 2), feed of 0.124 mm/rev (level 1), depth of cut of 0.3 mm (level 1) and a cutting fluid with a viscosity of 2.898 mm2/s (level 3). Hence, the optimal parameters to obtain better surface roughness of the workpiece material were obtained when groundnut oil based cutting fluid was used. Analysis of variance shows that feed rate has the most significant effect on surface roughness.

Synthesis of the CuInSe_2 thin film for solar cells using the electrodeposition technique and Taguchi method

The Taguchi method was used to obtain the optimum electrodeposition parameters for the synthesis of the CuInSe2 thin film for solar cells. The parameters consist of annealing temperature, current density, CuCl2 concentration, FeCl3 concentration, H2SeO3 concentration, TEA amount, pH value, and deposition time. The experiments were carried out according to an L18（2^13^7） table An X-ray diffractometer （XRD） and a scanning electron microscope （SEM） were respectively used to analyze the phases and observe the microstructure and the grain size of the CuInSe2 film before and after annealing treatment. The results showed that the CuInSe2 phase was deposited with a preferred plane （112） parallel to the substrate surface. The optimum parameters are as follows： current density, 7 mA/cm^2; CuCl2 concentration, 10 mM; FeCl3 concentration, 50 mM; H2SeO3 concentration, 15 mM; TEA amount, 0 mL; pH value, 1.65; deposition time, 10 min; and annealing temperature, 500℃.

The Interaction Effects of the Parameters on Optimization Design in Paper Production Waste Usage on Alkali-Activated Slag with Taguchi Method

The paper investigates the second-order interactions of parameters in an alkali-activated mixture of paper production waste(PPW)and blast furnace slag(BFS)in Taguchi method.The PPW including lime mud(LM)and paper sludge(PS).This paper provides the experimental models to assess the compressive and flexural strength of them at 7-day and 28-day.The results have shown that the second-order interactions between PPW and alkali-activated activator exists in each experimental model,and the significant interactions affect the selection of optimal compositions.Compared with the interactions between the PPW themselves,the interactions between PPW and alkali-activated parameters are the main significant factors affecting its physical properties.In each experimental model,the maximum compressive strength was 47.41 MPa in 7-day and 65.64 MPa in 28-day.Compared with the confirmatory experiments,the deviation of prediction calculated by experimental models was 3.08%and 0.56%,respectively.The maximum flexural strength was 5.74 MPa in 7-day and 5.96 MPa in 28-day;compared with the confirmatory experiments,the deviation of prediction calculated by experimental models was 5.40%and 0.17%.Considering the influence of circular materials,30%of PPW should be a suitable ratio to replace BFS as the raw material of alkali-activated slag(AAS).

Improvement of the CFRP Mechanical Properties Using Taguchi Method to Optimize the Formation Conditions

Carbon fiber composites have high strength, high stiffness and light weight characteristics to apply to many fields, such as leisure, energy and transportation industries. The CFRP （carbon fiber reinforced polymers/plastics） composites made of carbon fibers as reinforcement and epoxy resins as matrix were prepared by drum winding process. Various parameters such as molding temperature, molding pressure and pressing time were selected as the pre-pregs were laminated to be the CFRP. The effects of fabricating parameters which affected the mechanical properties of CFRPs were analyzed by Taguchi method in this study. The results showed that molding temperature was the main factor to influence the mechanical properties of composites.

Retro-Reflective Fiber Optic Displacement Sensor for Performance Optimization Using Taguchi Method

Fiber optic displacement sensors are widely used in industry. Retro reflective fiber optic displacement sensor consists of parallel fibers with a reflector at a distance. Light is launched into the transmitting fiber which gets reflected by reflector. This reflected light is collected by the receiving fiber. The received light is function of the displacement of the reflector from the fiber end faces. This paper is targeted to obtain a robust design for the fiber optic displacement sensor (FODS) using well known Taguchi method. The design takes care of all noise parameters within constraints of manufacturing tolerances. The statistical data analysis is performed on the simulated results. The larger the better signal to noise quality characteristics is used to find the effect of control parameters in the data analysis. Taguchi analysis suggests dominant parameters, which affects the sensitivity of the FODS and causes immunity to noise. A source fiber inclination angle is chosen as an adjustment parameter. Other control parameters are used for fine tuning of the FODS design for achieving three qualities viz. best robustness, optimized sensitivity and robustness and best sensitivity.

Optimization of back bead geometry in the PMAG-TIG twin arc hybrid root welding process using grey based Taguchi method

This study investigated multi-response optimization of the pulse metal active gas-tungsten inert gas( PMAG-TIG) twin arc hybrid root welding process for an optimal parametric combination to yield favorable back bead geometry of welded joints using grey relational analysis and Taguchi method.Eighteen experimental runs based on an orthogonal array following the Taguchi method were performed to derive objective functions to be optimized within the experimental domain.The objective functions were selected in relation to parameters of PMAG-TIG twin arc root welding back bead geometry: back bead width to root reinforcement ratio and deposited metal height.The Taguchi approach was followed by grey relational analysis to solve the multi-response optimization problem.The significance of factors on overall quality characteristics of the weld joint was also evaluated quantitatively using analysis of variance.Optimal results were verified through additional experiments,and showed to feasibility of applying grey relation analysis in combination with Taguchi technique for continuous improvement of product quality in the manufacturing industry.

Process Window Determination for Biofiltration by the Taguchi Method

Raw water from the Yantian Reservoir in Southern China was used for this study. Several process parameters of biofiltration, temperature, media, empty bed contact time, ozone dosage and concentration of geosmin and MIB, were adopted in order to determine their effects. Experiments were conducted using the Taguchi method and 9 experiments were needed to obtain the best process parameter settings and parameter effects. The results of these experiments indicate the use of biological filtration as a method of geosmin and MIB removal, to be satisfactory. In addition, the results show that temperature impacts the removal rate of both geosmin and MIB. Useful insights into the effects of the filter media on such as, empty bed contact time, ozone dosage and concentration of geosmin and MIB were also obtained.

Dry Sliding Wear Behaviour of Aluminium/Be₃Al₂(SiO₃)₆Composite Using Taguchi Method

The present study deals with investigation relating to the influence of wear parameters like sliding speed, applied load and sliding distance on the dry sliding wear of aluminium metal matrix composites. The design of experiment approach was employed to acquire data in controlled way using Taguchi method. A Pin-on-disc apparatus was used to conduct the dry sliding wear test. An orthogonal array, signal-to-noise ratio and analysis of variance were employed to investigate the wear behavior of aluminium and it’s composite. The mathematical model was obtained to determine the wear rate of the aluminium and it’s composite. The confirmation tests were conducted to verify the experimental results. The incorporation of Be3Al2(SiO3)6 as reinforcement material in aluminium matrix material improves the tribological characteristics.

An Application of the Taguchi Method (Robust Design) to Environmental Engineering: Evaluating Advanced Oxidative Processes in Polyester-Resin Wastewater Treatment

This paper presents the Taguchi Method, a statistical design modelling for experiments applied in environmental engineering. This method was applied to optimize the treatment conditions of polyester-resin effluent by means of Advanced Oxidative Processes (AOPs) using chemical oxygen demand (COD) as response parameter. The influence of each independent parameter including respective interactions was evaluated by Taguchi Method, which allowed determining the most statistically significant variables and conditions to best fit the process. Results showed that Taguchi Method is a very useful tool for environmental engineering field and possible simplifications of analysis and calculations through commercially available software.